Search

In this work, pure and S–N/WO3 (1%–7%) nanoparticles (NPs) have been developed for the degradation of MB dye. Optical properties, vibrational analysis, morphology, structural analysis, and photocatalytic activity of the samples have been evaluated using a variety of characterization techniques, including UV–vis, PL, FTIR, SEM, and x-ray diffraction (XRD). The XRD patterns showed that the stability of the orthorhombic phase of WO3 was affected by the concentrations of S and N. In SEM, nanospheres with an average size of 80 nm of NPs have been observed. The PL results showed that the e−, h+ recombination rate for the S–N7%/WO3 sample was the lowest. The degradation of MB dye has also been investigated in order to investigate the photocatalytic performance. Remarkably, S–N7%/WO3 shows the best results, with a maximum degradation of 90% in 120 min. The stability of the improved catalyst was tested using recycling and trapping studies. S–N7%/WO3 catalyst's exceptional photocatalytic activity highlights its potential use in wastewater treatment. This study will be helpful for manufacturing innovation. [ABSTRACT FROM AUTHOR]

It is vital to conduct research on the behaviour of natural fibre composites under cyclic loading in order to have confidence in the mechanical durability. During this study, the fabrication of composite laminates will be carried out by the hybridization effect of natural and synthetic fibres. Quantifying the impact that the SiC filler (10, 20, and 30 g) has when combined with the fibre reinforcement and epoxy matrix (275 g) under cyclic loading circumstances and determining the significant sequence of hybrid composites are the goals of this research. The results of the tensile mode were used to determine the input parameters, and based on the tensile strength of the hybrid composite, 70% of the tensile strength was fixed at 3 Hz frequency as the input for fatigue analysis. The life span was then determined for the hybrid composite. The results of this fatigue test showed that increasing the amount of SiC nanofillers produced a very high potential output for the fatigue test. As a result of increasing the amount of silicon carbide fillers from 10 to 30 g, sample S3 was able to significantly tolerate 65% more life. Failure mode can be identified from scanning electron microscope analysis revealing the major porosity, matrix crack, and laminate bonding strength that causes the failure during fatigue analysis.

The Prunus armeniaca L. (bitter apricot) is an apricot fruit tree categorized on the basis of the bitter taste of its seed kernel. In this study, the functional, medicinal, and therapeutic potential of bitter apricot seed kernel oil (BASKO) was evaluated. The qualitative screening of BASKO was performed using standard methodologies. The chemical profile of the oil was analyzed with the help of Fourier transform infrared (FTIR) and gas chromatography and mass spectrometry (GC‐MS). Results revealed the presence of different phytochemical constituents comprising steroids, flavonoids, terpenoids, alkaloids, and cardiac glycosides. The antioxidant activity of the oil was determined by a 2,2,diphenyl‐1picrylhydrazyl (DPPH) radical inhibition essay. Total phenolic and flavonoid contents were 10.6 ± 1.32 mg GAE/g and 4.75 ± 0.11 mg QE/g, respectively. DPPH inhibition of 89.5% was achieved at 1000 μg/mL of BASKO, with IC50 = 90.44 μg/mL (83.47–96.67 μg/mL with 95% CI). The antimicrobial potential of the BASKO revealed the inhibition of Escherichia coli (20.3 ± 2.08 mm), Salmonella typhi (19.3 ± 2.51 mm), Klebsiella pneumoniae (16.6 ± 1.52 mm), Pseudomonas aeruginosa (17 ± 2 mm), and Staphylococcus aureus (25 ± 1.01 mm). The minimum inhibitory concentration (MIC) value was 250 μL/mL for K. pneumoniae, S. typhi, P. aeruginosa, and S. aureus, whereas 62.5 μL/mL for E. coli. Moreover, BASKO showed antifungal potential against Trichophyton tonsurans (77.3 ± 2.08%), Epidermophyton floccosum (69.6 ± 3.51%), Aspergillus niger (74.3 ± 2.56%), Aspergillus flavus (90 ± 3%), and Mucor mucedo (78.3 ± 2.51%). Antileishmanial activity of oil was evaluated against Leishmania major by MTT assay, and an IC50 value of 89.75 μg/mL was observed. The study revealed that BASKO is a good source of biologically active compounds to be used as functional, therapeutical, and antimicrobial agents in food and pharmaceutical products. [ABSTRACT FROM AUTHOR]

Sauerkraut‐derived lactic acid bacterial (LAB) strains have gained attention due to their potential health benefits. This study focuses on evaluating seven Sauerkraut‐derived RAMULAB strains isolated from sauerkraut, aiming to identify promising candidates for modulating α‐glucosidase (AG) and α‐amylase (AM) enzymatic functions. RAMULAB strains with remarkable probiotic potential can contribute to the digestive health and manage conditions like diabetes. Identifying robust candidates from sauerkraut, a fermented food, holds promise for natural and cost‐effective probiotic sources. The RAMULAB strains underwent extensive characterization, including identification through 16S ribosomal RNA (rRNA) sequencing. Their tolerance to harsh conditions, adherence properties, antimicrobial activity, antioxidant potential, and inhibition of AG and AM were assessed. In silico analyses explored their molecular interactions, particularly with hydroxycitric acid, a potential antidiabetic compound. Among the RAMULAB strains, RAMULAB48 emerged as a standout candidate. It displayed exceptional resilience to acidic bile (≥97%), and simulated gastrointestinal conditions (≥95%), highlighting its suitability for probiotic applications. RAMULAB48 exhibited robust adherence properties, including cell‐surface hydrophobicity (80%), autoaggregation (42%), coaggregation with pathogens (≥33%), and adhesion to epithelial cells. Additionally, all seven isolates demonstrated gamma‐hemolysis and resistance to antibiotics (Kanamycin, Methicillin, and Vancomycin), while displaying strong antibacterial properties against foodborne pathogens. These RAMULAB strains also exhibited varying degrees of antioxidant activity, with RAMULAB48 displaying the highest potential (≥41%). In terms of antidiabetic activity, cell‐free supernatant (CS) obtained from RAMULAB48 expressed the highest inhibition levels, notably inhibiting yeast AG by an impressive 59.55% and AM being by a remarkable 67.42%. RAMULAB48 produced organic acids, including hydroxycitric acid (28.024 mg/mL), which showed promising antidiabetic properties through in silico analyses, indicating favorable interactions with the target enzymes. This study identifies Lacticaseibacillus paracasei RAMULAB48, a Sauerkraut‐derived RAMULAB strain, as a promising probiotic candidate with exceptional tolerance, adherence properties, antimicrobial activity, antioxidant potential, and antidiabetic effects. The presence of hydroxycitric acid further underscores its potential in managing diabetes. [ABSTRACT FROM AUTHOR]

Fruit peels are usually disposed of or treated as fertilizer. The peel, however, contains rich nutrients that can be used as a medium for growing microbes. Conventional culture medium is widely used for growing microbes, but the cost is very high and it is not suitable to produce cyanobacterium-based biofuel, biomass, and in other applications. Therefore, this study explores the potential for using fruit peels as a culture medium for Anabaena cylindrica. The fruit peels were dried, homogenized, and filtered to make different concentrations of fruit peel media (5%, 10% and 20%). For comparison, BG-11 medium acted as a positive control whereas deionized water serves as a negative control in this experiment. Growth of A. cylindrica in different types of media was analyzed after cell counting using a hemacytometer and biomass measuring. The cyanobacterial growth rate and biomass production were recorded in different types of fruit peel media with different concentrations. A. cylindrica have greater biomass yield when growing in 20% papaya peel medium and a higher growth rate when growing in 10% pineapple peel media compared to that growing in the BG-11 medium. In other words, the fruit peel media have more potential in growing cyanobacteria than conventional medium.

The release of pollutant such as lead (Pb) from factories, agriculture wastes, and domestic wastes into the environment has threatened the freshwater ecosystem. Therefore, there is a crucial need for a quick and efficient method for early detection of Pb in the aquatic environment. The aim of this study is to determine the changes of physicochemical parameters (pH, conductivity and dissolve oxygen) in the surrounding water body caused by Chlorella vulgaris that were exposed to Pb, as a mean of Pb bio-detection. The microalgae were exposed to different concentrations of Pb (1, 0.1 and 0.01 mg/L) and for each exposure, the physicochemical parameter changes in the surrounding water body were recorded at 0 hour (initial exposure), 1 hour, 2 hours, 6 hours and 24 hours by using the portable multiparameter meter. The results showed that the pH values of the water decreases as the concentration of metal exposure increases. On the other hand, the conductivity and dissolved oxygen showed a decreased in their values as the exposure time increases. This phenomenon could be attributed to the inhibition of the photosynthesis by the C. vulgaris as well as the ability of the algae to accumulate Pb and thus lowering the physicochemical parameters. Therefore, C. vulgaris serves as a good bioindicator for Pb pollution.

In present work, synthesis of a nanohybrid material using Fe and MoS2 has been performed via a cost‐effective and environmentally friendly route for sustainable manufacturing innovation. Rice straw extract was prepared and used as a reducing and chelating agent to synthesize the nanohybrid material by mixing it with molybdenum disulfide (MoS2) and ferric nitrate [Fe (NO3)3.9H2O], followed by heating and calcination. The X‐ray diffraction (XRD) pattern confirms the formation of a nanohybrid consisting of monoclinic Fe2(MoO4)3, cubic Fe2.957O4, and orthorhombic FeS with 86% consisting of Fe2(MoO4)3. The properties were analyzed through Fourier‐transformed infrared spectroscopy (FTIR), atomic force microscopy (AFM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results of the dynamic light scattering (DLS) study revealed a heterogeneous size distribution, with an average particle size of 48.42 nm for 18% of particles and 384.54 nm for 82% of particles. Additionally, the zeta potential was measured to be −18.88 mV, suggesting moderate stability. X‐ray photoelectron spectroscopy (XPS) results confirmed the presence of both Fe2+ and Fe3+ oxidation states along with the presence of Molybdenum (Mo), oxygen (O), and Sulphur (S). The prepared nanohybrid material exhibited a band gap of 2.95 eV, and the photoluminescence intensity increased almost twice that of bare MoS2. The present work holds potential applications in photo luminescent nanoplatform for biomedical applications. [ABSTRACT FROM AUTHOR]

The treatment of palm oil mill effluent (POME) poses a significant challenge for Malaysia's palm oil industry, necessitating compliance with the Department of Environment (DOE) regulations prior to discharge. This study introduces an eco-friendly synthesis method utilizing mangosteen (Garcinia mangostana L.)-leaf aqueous extract to fabricate copper oxide (CuO), zinc oxide (ZnO) nanoparticles (NPs), and their nanocomposite (CuO-ZnO NCs). The physicochemical properties of these nanomaterials were characterized using various analytical tools and their effectiveness in reducing the chemical oxygen demand (COD) of palm oil mill effluent (POME) was assessed under the illumination of two types of light sources: monochromatic blue- and polychromatic white-light emitting diodes (LEDs). CuO-ZnO NCs demonstrated superior performance, with the lowest energy bandgap (1.61 eV), and achieved a COD removal efficiency of 63.27% ± 0.010 under blue LED illumination, surpassing the DOE's discharge limit of 100 mg/L. This study offers a cost-effective and environmentally friendly method for synthesizing heterojunction materials, which show great potential as photocatalysts in reducing POME COD to permissible levels for discharge. [ABSTRACT FROM AUTHOR]

This study presents a novel approach for the fabrication of a Co,Ni/MoS2‐derived nanohybrid material using wheat straw extract. The facile synthesis method involves a sol–gel process, followed by calcination, showcasing the potential of agricultural waste as a sustainable reducing and chelating reagent. The as‐prepared nanohybrid has been characterized using different techniques to analyse its physicochemical properties. X‐ray diffraction analysis confirmed the successful synthesis of the nanohybrid material, identifying the presence of NiMoO4, CoSO4 and Mo17O47 as its components. Fourier‐transform infrared spectroscopy differentiated the functional groups present in the wheat straw biomass and those in the nanohybrid material, highlighting the formation of metal–oxide and sulphide bonds. Scanning electron microscopy revealed a heterogeneous morphology with agglomerated structures and a grain size of around 70 nm in the nanohybrid. Energy‐dispersive X‐ray spectroscopy analysis shows the composition of elements with weight percentages of (Mo) 9.17%, (S) 6.21%, (Co) 12.48%, (Ni) 12.18% and (O) 50.46% contributing to its composition. Electrochemical analysis performed through cyclic voltammetry showcased the exceptional performance of the nanohybrid material as compared with MoS2, suggesting its possible applications for designing biosensors and related technologies. Thus, the research study presented herein underscores the efficient utilization of natural resources for the development of functional nanomaterials with promising applications in various fields. This study paves a way for manufacturing innovation along with advancement of novel synthesis method for sustainable nanomaterial for future technological developments. [ABSTRACT FROM AUTHOR]

Composites are versatile materials that can be tailored to meet the specific needs of various industries, including aerospace, automotive, and construction. This study focuses on investigating how the amount of titanium-di-boride (TiB2) particles (0%, 3%, 6%, and 9%) affects the physical, mechanical, microstructural, and fracture properties of Al7075/TiB2 composites produced using a liquid-state stir-casting process. The addition of TiB2 particles increases the hardness and tensile strength of the Al7075 alloy. This has been confirmed by X-ray diffraction analysis, which showed that these particles are dispersed throughout the aluminum matrix. The hardness increases from 60 HV to 90 HV and the tensile strength increases from 140 MPa to 211 MPa. The significance of increased wettability brought about by the addition of magnesium powder and the preheating of a ceramic reinforcement before pouring molten metal was revealed by scanning electron micrographs of the cast composites, which showed an even dispersal of reinforcements in the aluminum matrix, establishing the strong connection between the matrix and the reinforcement agents. Fracture surface scanning electron microscopy revealed that micro-void formation and nucleation in Al7075/TiB2 composites resulted in ductile material paves a way for manufacturing innovation. [ABSTRACT FROM AUTHOR]

In this current work, pristine Ti O 2 , BiV O 4 , and Ti O 2 /BiV O 4 ( 1%, 3%, 5%, and 7%) nanocomposites were prepared for the deteriorate of MB dye and tetracycline antibiotic. For synthesis aim, an easy and facile hydrothermal method has been utilized. Several characterization techniques like XRD, SEM, UV–Vis, and PL spectroscopic analysis have been performed to address the structural, morphological, and optical properties of the nanocomposites. It was observed that 5% Ti O 2 /BiV O 4 plays a significant role in decreasing the recombination rate of photogenerated electron/hole pairs, subsequently in the reduction of band gap. Interestingly, a nanocomposite of 5% TiO2/BiVO4 demonstrates the excellent deteriorate of Methylene and Tetracycline, with rates of 87% and 72%, respectively within 120 min. To check the stability of the optimized catalyst, recyclability and trapping investigations have been performed. Moreover, the 5% Ti O 2 /BiV O 4 photocatalyst exhibits good stability in five cycles for the degradation of MB dye and Tetracycline and paves a way for manufacturing innovation. [ABSTRACT FROM AUTHOR]