Search

Triplet‐triplet annihilation upconversion (TTA‐UC) is a photophysical process in which two low‐energy photons are converted into one higher‐energy photon. This type of upconversion requires two species: a sensitizer that absorbs low‐energy light and transfers its energy to an annihilator, which emits higher‐energy light after TTA. In spite of the multitude of applications of TTA‐UC, few families of annihilators have been explored. In this work, we show dipyrrolonaphthyridinediones (DPNDs) can act as annihilators in TTA‐UC. We found that structural changes to DPND dramatically increase its upconversion quantum yield (UCQY). Our optimized DPND annihilator demonstrates a high maximum internal UCQY of 9.4 %, outperforming the UCQY of commonly used near‐infrared‐to‐visible annihilator rubrene by almost double. [ABSTRACT FROM AUTHOR]

A rapidly growing interest in organic bioelectronic applications has spurred the development of a wide variety of organic mixed ionic‐electronic conductors. While these new mixed conductors have enabled the community to interface organic electronics with biological systems and efficiently transduce biological signals (ions) into electronic signals, the current materials selection does not offer sufficient selectivity towards specific ions of biological relevance without the use of auxiliary components such as ion‐selective membranes. Here, we present the molecular design of an n‐type (electron‐transporting) perylene diimide semiconductor material decorated with pendant oligoether groups to facilitate interactions with cations such as Na+ and K+. Using the cyclic 15‐crown‐5 oligoether motif, we find that the resulting mixed conductor PDI‐crown displays a strong dependence on the size of the electrolyte cation when tested in an organic electrochemical transistor configuration. In stark contrast to the low current response on the order of 1 μA observed with aqueous sodium chloride, a nearly 200‐fold increase in current is observed with aqueous potassium chloride. We ascribe the high selectivity to extended molecular aggregation and therefore efficient charge transport in the presence of K+ due to a favourable sandwich‐like structure between two adjacent 15‐crown‐5 motifs and the potassium ion. [ABSTRACT FROM AUTHOR]

Dynamic mechanical analysis (DMA) is a powerful technique for characterizing the mechanical properties of a wide range of materials. However, the importance of DMA in studying organic/polymer semiconductors has not been fully appreciated. In this Highlight, we explore recent advancements in the use of DMA in understanding the viscoelastic and mechanical properties and thermal transitions of organic semiconductor materials. In particular, the insights gained from DMA can serve as new guides for the device optimisation of organic solar cells towards stable operation. Furthermore, we present key findings, challenges, and future directions to advance the application of DMA in organic electronics. [ABSTRACT FROM AUTHOR]

Transconductance (gm) is one important figure of merit for benchmarking organic electrochemical transistor (OECT) biosensors, which nevertheless experiences undesired fluctuation instead of keep constant during the target detection of varied concentrations. Light‐matter interplay is recently shown as a potential way to regulate the OECT characteristics, e.g. maximum gm at zero gate bias is achieved. In this work, the challenge of unstable gm is addressed by using a unique metal‐organic framework (MOF)‐derived hollow tube indium sulfide (m‐In2S3) as the photogate. Interestingly, the light irradiation on m‐In2S3 generate a straight transfer curve, leading to a stable gm that is desirable for biological application. Exemplifying by an aptasening, such a device is then tested for protein quantification with a stable sensitivity during the detection. This work features the feasibility of light‐matter interplay to achieve a stable gm in organic electronics. [ABSTRACT FROM AUTHOR]

Semiconducting photoresists hold great promise for scale‐up manufacturing of organic field‐effect transistors (OFETs) for integrated organic electronics. While photolithographic p‐type OFETs have achieved a considerable balance among patterning precision, electrical properties and process stability, it remains challenging for n‐type OFETs due to the inherent limited mobility and ambient instability. Herein, a n‐type semiconducting photoresist (SPr) is developed that is compatible with photolithography procedures. By utilizing the solvent‐driven force, a self‐encapsulated blend film with gradient semiconductor phase is prepared, where the underneath transistor active layer is protected by the upper cross‐linked network, avoiding solvent erosion and air doping. As such, a mobility up to 1.1 cm2 V−1 s−1 that is comparable with amorphous Si is achieved, with remained mobility by ≈90% after long‐term exposure to developer and stripper or atmospheric conditions. The sub‐micrometer patterning accuracy of SPr enables the fabrication of organic transistor arrays with a density of 9 × 105 units cm−1, which is comparable to other state‐of‐the‐art devices fabricated by the printing or photolithography, demonstrating immense potential in integrated organic electronics. [ABSTRACT FROM AUTHOR]

Cellulose is a natural polymer with great properties such as high optical transparency and mechanical strength, flexibility, and biodegradability. Hence, cellulose‐based foils are suitable for the replacement of synthetic polymers as substrate materials in organic electronics. This article reports the fabrication of ultrathin, free‐standing cellulose foils by spraying aqueous 2,2,6,6‐tetramethylpiperidine‐1‐oxyl‐nanocellulose (TEMPO) fibrils ink layer‐by‐layer on a hot substrate using a movable spray nozzle. The resulting foils are only 2 ± 1 µm in thickness with an average basis weight of 1.9 g m−2, which ranges in the same scale as the world's thinnest paper. The suitability of these ultra‐thin nanocellulose foils as a sustainable substrate material for organic electronic applications is demonstrated by testing the foils resistance against organic solvents. Furthermore, silver nanowires (AgNWs) and the blend poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) are integrated into the foils, and the foils are molded into 3D paper structures in order to create conductive, paper‐based building blocks for organic electronics. [ABSTRACT FROM AUTHOR]

The optoelectronic properties of semiconducting polymers and device performance rely on a delicate interplay of design and processing conditions. However, screening and optimizing the relationships between these parameters for reliably fabricating organic electronics can be an arduous task requiring significant time and resources. To overcome this challenge, Polybot is developed—a robotic platform within a self‐driving lab that can efficiently produce organic field‐effect transistors (OFETs) from various semiconducting polymers via high‐throughput blade coating deposition. Polybot not only handles the fabrication process but also can conduct characterization tests on the devices and autonomously analyze the data gathered, thus facilitating the rapid acquisition of data on a large scale. This work leverages the capabilities of this platform to investigate the fabrication of OFETs using hydrogen bonding‐containing semiconducting polymers. Through high‐throughput fabrication and characterization, various data trends are analyzed, and large extents of anisotropic charge mobility are observed in devices. The materials are thoroughly characterized to understand the role of processing conditions in solid state and electronic properties of these organic semiconductors. The findings demonstrate the effectiveness of automated fabrication and characterization platforms in uncovering novel structure–property relationships, facilitating refinement of rational chemical design, and processing conditions, ultimately leading to new semiconducting materials. [ABSTRACT FROM AUTHOR]

The potential use of n-type small organic molecules in electrodes has attracted significant attention in organic electronics owing to the easy, high-yield purification processes of organic compounds. However, only few studies have reported high-efficiency supercapacitors based on n-type organic materials. Nevertheless, most n-type organic compounds possess low capacitance and poor cycling efficiency. Therefore, it is crucial to develop n-type organic compounds that demonstrate good electrochemical properties for use in electrodes. Herein, both the (E)-N-(4-(diphenylamino)benzylidene)-6,6,10,10-tetramethyl-4-phenyl-6,7,8,9,10,10a-hexahydro-5H-6a,9-methanobenzo[H]quinazolin-2-amine (TPAB) and (E)-N-(4-(diphenylamino)benzylidene)-4-(4-(diphenylamino)phenyl)-6,6,10,10-tetramethyl-6,7,8,9,10,10a-hexahydro-5H-6a,9-methanobenzo [h]quinazolin-2-amine (TPANB) compounds containing electrochromic (EC) and aggregation-induced emission (AIE) groups were synthesized from triphenylamine (TPA) and quinazoline derivatives, and their structure and properties were investigated. These novel electrode materials demonstrate high EC and fluorescence performance just as a typical n-type semiconductor. The coloring time of a TPANB film is 4.00 s, whereas the bleaching time is 3.00 s. Compared with TPANB, TPAB electrode material demonstrate a high area-specific capacitance (2.38 mF cm−2 at 0.05 mA cm−2), outstanding the charge and discharge rate performance (93% with the current density of 0.05–0.25 mA cm−2), and excellent cycling performance (78.51%) after 300 cycles. Above all, the multifunctional materials hold good potential for intelligent display energy storage. [ABSTRACT FROM AUTHOR]

The crystal structures of 16 boron subphthalocyanines (BsubPcs) with structurally diverse axial groups were analyzed and compared to elucidate the impact of the axial group on the intermolecular π–π interactions, axial‐group interactions, axial bond length and BsubPc bowl depth. π–π interactions between the isoindole units of adjacent BsubPc molecules most often involve concave–concave packing, whereas axial‐group interactions with adjacent BsubPc molecules tend to favour the convex side of the BsubPc bowl. Furthermore, axial groups that contain O and/or F atoms tend to have significant hydrogen‐bonding interactions, while axial groups containing arene site(s) can participate in π–π interactions with the BsubPc bowl, both of which can strongly influence the crystal packing. Bulky axial groups did tend to disrupt the π–π interactions and/or axial‐group interactions, preventing some of the close packing that is seen in BsubPcs with less bulky axial groups. The atomic radius of the heteroatom bonded to boron directly influences the axial bond length, whereas the axial group has minimal impact on the BsubPc bowl depth. Finally, the crystal growth method did not generally appear to have a significant impact on the solid‐state arrangement, with the exception of water occasionally being incorporated into crystal structures when hygroscopic solvents were used. These insights can help with the design and fine‐tuning of the solid‐state structures of BsubPcs as they continue to be developed as functional materials in organic electronics. [ABSTRACT FROM AUTHOR]

In recent years, research in organic electronics, a burgeoning interdisciplinary field, has seen significant growth. Organic electronics aims to use organic materials to manufacture more flexible, environmentally friendly, and cost-effective electronic devices for applications in display technology, optoelectronics, energy conversion, and other fields. To enhance undergraduate students' understanding of organic electronics, this experimental teaching plan centers on the commonly used organic polymer P3HT. Using a spin coater, students prepare and modify active layers, then characterize the surface morphology of these films with a step profiler, optical microscope, and atomic force microscope. Conductivity testing of the devices is performed using a probe station. Comprehensive and standardized protective measures ensure safety throughout the experimental process. Additionally, the experiment incorporates fundamental techniques and the use of various instruments, fostering students' practical skills and scientific literacy. This experiment aims to ignite undergraduates' interest in the forefront of organic electronics through hands-on preparation, modification, and characterization of organic polymer films, thereby enhancing their innovative thinking and overall competencies. [ABSTRACT FROM AUTHOR]

n‐Type organic conductive molecules play a significant role in organic electronics. Self‐doping can increase the carrier concentration within the materials to improve the conductivity without the need for additional intentional dopants. This review focuses on the various strategies employed in the synthesis of self‐doped n‐type molecules, and provides an overview of the doping mechanisms. By elucidating these mechanisms, the review aims to establish the relationship between molecular structure and electronic properties. Furthermore, the review outlines the current applications of self‐doped n‐type molecules in the field of organic electronics, highlighting their performance and potential in various devices. It also offers insights into the future development of self‐doped materials. [ABSTRACT FROM AUTHOR]

Solvatochromism plays a pivotal role in various scientific and technological fields including those that explore molecular interactions, sensing technologies, and organic electronics. Notably, despite their ease of manipulation, direct visualization, and potential for single particle‐based sensing, micro‐sized solid particles have been the focus of a surprisingly low number of solvatochromism investigations. In this study, polydiacetylene (PDA) particles are synthesized and their solvatochromism is investigated at the single particle level using optical laser tweezers‐based methods. The findings reveal that unpolymerized monomers within PDA particles at the water/n‐decane interface undergo dissolution in the n‐decane phase to form internal voids in the particles. This phenomenon leads to structural deformation of the PDA which triggers a solvatochromic response. Studies that integrate this phenomenon with established particle‐based methodologies should provide deeper insights into diverse chromism behaviors and potential applications of solvatochromic materials. [ABSTRACT FROM AUTHOR]

Artificial skin with tactile perceptions is anticipated to play a pivotal role in next‐generation robotic and medical devices. The primary challenge lies in creating a biomimetic system that seamlessly integrates with the human body and biological systems. The authors have developed an electronic skin (e‐skin) that imitates the biological sensorimotor loop through medium‐scale circuit integration, boasting low power consumption and solid‐state synaptic transistors. [ABSTRACT FROM AUTHOR]

Organic materials have found widespread applications but require doping to overcome their intrinsically low carrier concentration. Doping injects free carriers into the polymer, moving the position of the Fermi level, and creates coulombic traps, changing the shape of the electronic density of states (DOS). We develop equations to explicitly map the DOS parameters to the Seebeck vs conductivity relationship. At low carrier concentrations, this relationship is a universal slope - k B / q , while at higher carrier concentrations, the slope becomes dependent on the shape of the DOS. We conclude that, at high doping, a heavy-tailed DOS leads to higher thermoelectric power factors. [ABSTRACT FROM AUTHOR]

Chemical doping is a powerful way to enhance the electrical performance of organic electronics. To avoid perturbing the ordered molecular packing of organic semiconducting hosts, molecular dopants are deposited on the surface of highly crystalline organic semiconductor thin films. However, such surface doping protocols not only limit charge‐transfer efficiency but also cause dopant diffusion problems, which significantly reduce charge carrier mobility and device stability. Here, an innovative anion bulk doping strategy is reported that allows effective doping of organic single‐crystalline films (OSCFs) without disrupting molecular ordering to improve the performance of organic field‐effect transistors (OFETs). This method is mediated by anion dopants and can be pictured as an effective charge transfer of dopants with organic semiconductors in liquid phase. The direct introduction of dopant anions overcomes limitations of partial charge transfer while avoiding interference from dopant aggregation with crystallization. Using this method, the average carrier mobility of the OSCFs is boosted by ≈2.5 times. Significantly, low‐voltage OFETs developed from anion‐doped OSCFs exhibit a near‐ideal subthreshold swing of 59.2 mV dec−1 and unparalleled mobility as high as 19.8 cm2 V−1 s−1 together with excellent stability. The concept of anion doping opens new avenues for improving the electrical performance of organic electronics. [ABSTRACT FROM AUTHOR]

Unipolar p‐ and n‐type organic field‐effect transistors (OFETs) are essential for constructing organic circuits and complementary designs crucial for high‐performance electronics. Traditionally, fabricating these transistors requires separate p‐type and n‐type organic semiconductors (OSCs), which complicates the process due to intricate patterning, protection of the first OSC layer, and considerable material wastage. In this work, an innovative approach is introduced, inspired by silicon transistor fabrication to obtain unipolar OFETs, employing a single ambipolar OSC in conjunction with doped organic semiconductor films (DOSCFs) as electrodes. This results demonstrate that OFETs with DOSCF electrodes suppress ambipolarity dramatically and achieve on/off ratios that are two to three orders of magnitude higher than those with metal electrodes, along with excellent stability. The unipolar characteristics of the devices are attributed to the unique work function properties and the intrinsic charge carrier behavior of the DOSCF electrodes. Significantly, inverter circuits utilizing these unipolar transistors outperformed traditional ambipolar transistors with metal electrodes, achieving a fivefold increase in voltage gain. This novel strategy promises to enhance the practicality and economic viability of organic electronics, paving the way for more sustainable and high‐performance circuit designs. [ABSTRACT FROM AUTHOR]

The thermal conductivity (κ) governs how heat propagates in a material, and thus is a key parameter that constrains the lifetime of optoelectronic devices and the performance of thermoelectrics (TEs). In organic electronics, understanding what determines κ has been elusive and experimentally challenging. Here, by measuring κ in 17 π‐conjugated materials over different spatial directions, it is statistically shown how microstructure unlocks two markedly different thermal transport regimes. κ in long‐range ordered polymers follows standard thermal transport theories: improved ordering implies higher κ and increased anisotropy. κ increases with stiffer backbones, higher molecular weights and heavier repeat units. Therein, charge and thermal transport go hand‐in‐hand and can be decoupled solely via the film texture, as supported by molecular dynamics simulations. In largely amorphous polymers, however, κ correlates negatively with the persistence length and the mass of the repeat unit, and thus an anomalous, albeit useful, behavior is found. Importantly, it is shown that for quasi‐amorphous co‐polymers (e.g., IDT‐BT) κ decreases with increasing charge mobility, yielding a 10‐fold enhancement of the TE figure‐of‐merit ZT compared to semi‐crystalline counterparts (under comparable electrical conductivities). Finally, specific material design rules for high and low κ in organic semiconductors are provided. [ABSTRACT FROM AUTHOR]

Developing fluorophores that conform to the Broadcast Service Television 2020 (BT.2020) standard presents a formidable challenge. Here, we propose an innovative approach that integrates two and three‐boron/nitrogen (BN2)‐embedded [4]helicene subunits with naphthalene, resulting in the synthesis of two novel narrowband bright green quasi‐fluorescent emitters, NT‐2B and NT‐3B for ultra‐high‐definition displays. These emitters exhibit minimal reorganization energy and Huang–Rhys factor, emitting at 510 and 511 nm in dilute toluene solution with exceptionally narrow full width at half maximum values of 15 and 14 nm, respectively. Notably, NT‐2B demonstrates an impressive photoluminescence quantum yield of 92.5 %, rapid radiative decay rate, and slow non‐radiative decay rate. Owing to their narrowband emission characteristics and outstanding optoelectronic properties, corresponding OLEDs based on NT‐2B demonstrate a high external quantum efficiency of 30.6 %, with an FWHM value of 21.5 nm and a CIEy of 0.74, positioning it as one of the leading narrow‐band green emitters. [ABSTRACT FROM AUTHOR]

Herein, we propose a regional functionalization molecular design strategy that enables independent control of distinct pivotal parameters through different molecule segments. Three novel multiple resonances thermally activated delayed fluorescence (MR‐TADF) emitters A‐BN, DA‐BN, and A‐DBN, have been successfully synthesized by integrating highly rigid and three‐dimensional adamantane‐containing spirofluorene units into the MR framework. These molecules form two distinctive functional parts: part 1 comprises a boron‐nitrogen (BN)‐MR framework with adjacent benzene and fluorene units forming a central luminescent core characterized by an exceptionally rigid planar geometry, allowing for narrow FWHM values; part 2 includes peripheral mesitylene, benzene, and adamantyl groups, creating a unique three‐dimensional "umbrella‐like" conformation to mitigate intermolecular interactions and suppress exciton annihilation. The resulting A‐BN, DA‐BN, and A‐DBN exhibit remarkably narrow FWHM values ranging from 18 to 14 nm and near‐unity photoluminescence quantum yields. Particularly, OLEDs based on DA‐BN and A‐DBN demonstrate outstanding efficiencies of 35.0 % and 34.3 %, with FWHM values as low as 22 nm and 25 nm, respectively, effectively accomplishing the integration of high color purity and high device performance. [ABSTRACT FROM AUTHOR]

Developing novel n‐type organic semiconductors is an on‐going research endeavour, given their pivotal roles in organic electronics and their relative scarcity compared to p‐type counterparts. In this study, a new strategy was employed to synthesize n‐type organic semiconductors featuring a fully fused conjugated backbone. By attaching two sets of adjacent amino and formyl groups to the indacenodithiophene‐based central cores and triggering a tandem reaction sequence of a Knoevenagel condensation‐intramolecular cyclization, DFA1 and DFA2 were realized. The solution‐processed organic field effect transistors based on DFA1 exhibited unipolar n‐type transport character with a decent electron mobility of ca. 0.10 cm2 V−1 s−1 (ca. 0.038 cm2 V−1 s−1 for DFA2 based devices). When employing DFA1 as a third component in organic solar cells, a high power conversion efficiency of 19.2 % can be achieved in ternary devices fabricated with PM6 : L8‐BO : DFA1. This work provides a new pathway in the molecular engineering of n‐type organic semiconductors, propelling relevant research forward. [ABSTRACT FROM AUTHOR]

Covalent organic frameworks linked by carbon‐carbon double bonds (C=C COFs) are an emerging class of crystalline, porous, and conjugated polymeric materials with potential applications in organic electronics, photocatalysis, and energy storage. Despite the rapidly growing interest in sp2 carbon‐conjugated COFs, only a small number of closely related condensation reactions have been successfully employed for their synthesis to date. Herein, we report the first example of a C=C COF, CORN‐COF‐1 (CORN=Cornell University), prepared by N‐heterocyclic carbene (NHC) dimerization. In‐depth characterization reveals that CORN‐COF‐1 possesses a two‐dimensional layered structure and hexagonal guest‐accessible pores decorated with a high density of strongly reducing tetraazafulvalene linkages. Exposure of CORN‐COF‐1 to tetracyanoethylene (TCNE, E1/2=0.13 V and −0.87 V vs. SCE) oxidizes the COF and encapsulates the radical anion TCNE⋅− and the dianion TCNE2− as guest molecules, as confirmed by spectroscopic and magnetic analysis. Notably, the reactive TCNE⋅− radical anion, which generally dimerizes in the solid state, is uniquely stabilized within the pores of CORN‐COF‐1. Overall, our findings broaden the toolbox of reactions available for the synthesis of redox‐active C=C COFs, paving the way for the design of novel materials. [ABSTRACT FROM AUTHOR]

In this work, we present the innovative synthesis of salophen (acetaminosalol) derivatives in a solvent-free environment by high-speed ball milling, using a non-conventional activation method, which allowed obtaining compounds in a shorter time and with a better yield. Furthermore, for the first time, the salophen derivatives were deposited as composite films, using a matrix of poly 3,4-ethylene dioxythiophene:polystyrene sulfonate (PEDOT:PSS) polymer. Significant findings include the transformation from the benzoid to the quinoid form of PEDOT post-IPA treatment, as evidenced by Raman spectroscopy. SEM analysis revealed the formation of homogeneous films, and AFM provided insights into the changes in surface roughness and morphology post-IPA treatment, which may be crucial for understanding potential applications in electronics. The optical bandgap ranges between 2.86 and 3.2 eV for PEDOT:PSS-salophen films, placing them as organic semiconductors. The electrical behavior of the PEDOT:PSS-salophen films undergoes a transformation with the increase in voltage, from ohmic to space charge-limited conduction, and subsequently to constant current, with a maximum of 20 mA. These results suggest the possible use of composite films in organic electronics. [ABSTRACT FROM AUTHOR]

Displays have become ubiquitous in our modern and highly interconnected lives. Complex vacuum processed multi‐stacks are widely integrated into high tech, high value products such as smart phones, while solution processed large area single‐layer OLEDs appear more adequate for basic applications focusing on recyclability such as packaging, road signage, advertising, and single‐use health care products. In this context, we report herein the design, synthesis, and characterization of an accessible series of oligothiophenes end‐capped triphenylamines that were preprepared by atom‐economical direct (hetero)arylation reactions and successfully used as emitter in solution processed devices, from lab scale to large area printed and flexible demonstrator. [ABSTRACT FROM AUTHOR]

The nature of interchain π-system contacts, and their relationship to hole transport, are elucidated for the high-mobility, noncrystalline conjugated polymer C16-IDTBT by the application of scanning tunneling microscopy, molecular dynamics, and quantum chemical calculations. The microstructure is shown to favor an unusual packing motif in which paired chains cross-over one another at near-perpendicular angles. By linking to mesoscale microstructural features, revealed by coarse-grained molecular dynamics and previous studies, and performing simulations of charge transport, it is demonstrated that the high mobility of C16-IDTBT can be explained by the promotion of a highly interconnected transport network, stemming from the adoption of perpendicular contacts at the nanoscale, in combination with fast intrachain transport. [ABSTRACT FROM AUTHOR]

Realizing highly efficient organic light‐emitting diodes (OLEDs) based on "hot exciton" emitters is crucial for the widespread use of purely organic electroluminescence. Herein, it is demonstrated that the radiative decay rate, modulated by molecular configuration, plays a vital role in determining the optoelectronic properties of hot exciton materials. The proof‐of‐concept isomers, TPA‐1IPCN and TPA‐3IPCN, and TPA‐1IANCN and TPA‐3IANCN are intentionally designed and successfully synthesized. By employing a novel donor–acceptor–acceptor (D–A'–A) molecular architecture, implementing a molecular isomerization strategy, incorporating diverse steric hindrance moieties, and strategically manipulating the positioning of functional groups, precise modulation of the molecular configuration can be achieved to enable accurate regulation of the radiative decay rate. Consequently, various optoelectronic properties, including photoluminescent wavelength, photoluminescence quantum yield, fluorescence lifetime, packing mode in aggregated state, and molecular horizontal dipole ratios in films, undergo significant modifications. As a result, non‐doped blue OLED based on TPA‐1IPCN exhibits outstanding maximum external quantum efficiency (EQE) of 10.3% with minimal efficiency roll‐off—one of the highest reported values for blue OLEDs based on hot exciton materials. [ABSTRACT FROM AUTHOR]

Layered (2D) perovskites are an emerging attractive 2D system with enhanced stability to ambient conditions as opposed to their highly unstable three dimensional bulk counterpart. Their uniquely tuneable optical and electrical properties are underpinning a surge of interest in 2D‐photovoltaics. So far, the development of nano‐scale integrated opto‐electronic 2D perovskite devices remains nearly unexplored since they have generally been found to be incompatible with standard top‐down semiconductor nano‐fabrication technologies. Here, following the synthesis of solvent‐stable 2D‐fluorinated phenethylammonium lead iodide perovskite (F‐PEA)2PbI4 (F‐PEAI), planar photodetectors entirely fabricated in atmosphere is demonstrated, exhibiting figures of merit rivalling those of commercial silicon photodiodes. A record large room temperature detectivity (>5 × 1017 Jones), a fast time photoresponse (rise time 1.5 ns), an extraordinarily large linear dynamic range (228 dB), as well as a photo‐responsivity of ≈ 1100 AW−1 are demonstrated for devices on a range of substrates including flexible wearable media without the need for any planarization or any atomically thin dielectric, in stark contrast to other 2D semiconductors. Finally, the suitability of nano‐scale 2D F‐PEAI photodetector arrays with sub‐wavelength pixel size of just 100 nm of use for high definition imaging is demonstrated. [ABSTRACT FROM AUTHOR]

Recently, much research has focused on the search for new mixed donor–acceptor layers for applications in organic electronics. Organic heterostructures with layers based on the generation 1 poly(propylene thiophenoimine) (G1PPT) dendrimer, N,N′-diisopropylnaphthalene diimide (MNDI), and a combination of the two were prepared and their electrical properties were investigated. Single layers of G1PPT and MNDI and a mixed layer (G1PPT:MNDI) were obtained via spin coating on quartz glass, silicon, and glass/ITO substrates, using chloroform as a solvent. The absorption mechanism was investigated, the degree of disorder was estimated, and the emission properties of the layers were highlighted using spectroscopic methods (UV–Vis transmission and photoluminescence). The effects of the concentration and surface topographical particularities on the properties of the layers were analyzed via atomic force microscopy. All of the heterostructures realized with ITO and Au electrodes showed good conduction, with currents of the order of mA. Additionally, the heterostructure with a mixed layer exhibited asymmetry in the current–voltage curve between forward and reverse polarization in the lower range of the applied voltages, which was more significant at increased concentrations and could be correlated with rectifier diode behavior. Consequently, the mixed-layer generation 1 poly(propylene thiophenoimine) dendrimer with N,N′-diisopropylnaphthalene diimide can be considered promising for electronic applications. [ABSTRACT FROM AUTHOR]

The production of nanofibers has become a significant area of research due to their unique properties and diverse applications in various fields, such as biomedicine, textiles, energy, and environmental science. Electrospinning, a versatile and scalable technique, has gained considerable attention for its ability to fabricate nanofibers with tailored properties. Among the wide array of conductive polymers, poly(3,4-ethylenedioxythiophene) (PEDOT) has emerged as a promising material due to its exceptional conductivity, environmental stability, and ease of synthesis. The electrospinning of PEDOT-based nanofibers offers tunable electrical and optical properties, making them suitable for applications in organic electronics, energy storage, biomedicine, and wearable technology. This review, with its comprehensive exploration of the fabrication, properties, and applications of PEDOT nanofibers produced via electrospinning, provides a wealth of knowledge and insights into leveraging the full potential of PEDOT nanofibers in next-generation electronic and functional devices by examining recent advancements in the synthesis, functionalization, and post-treatment methods of PEDOT nanofibers. Furthermore, the review identifies current challenges, future directions, and potential strategies to address scalability, reproducibility, stability, and integration into practical devices, offering a comprehensive resource on conductive nanofibers. [ABSTRACT FROM AUTHOR]

The fabrication of nanocellulose-based substrates with high dielectric permittivity and anisotropic thermal conductivity to replace synthetic thermoplastics in flexible organic electronics remains a big challenge. Herein, films were prepared from native (CNF) and carboxylated (TCNF) cellulose nanofibrils, with and without the addition of thermally conductive multi-layered Ti3C2Tx MXene, to examine the impact of polar (− OH, − COOH) surface groups on the film morphological, moisturizing, dielectric, and thermal dissipation properties. The electrostatic repulsion and hydrogen bonding interaction between the hydrophilic surface/terminal groups on CNF/TCNF and MXene was shown to render their self-assembly distribution and organization into morphologically differently structured films, and, consequently, different properties. The pristine CNF film achieved high intrinsic dielectric permittivity (ε' ~ 9), which was further increased to almost ε' ~ 14 by increasing (50 wt%) the MXene content. The well-packed and aligned structure of thinner TCNF films enables the tuning of both the composite's dielectric permittivity (ε' ~ 6) and through-plane thermal conductivity (K ~ 2.9 W/mK), which increased strongly (ε' ~ 17) at higher MXene loading giving in-plane thermal conductivity of ~ 6.3 W/mK. The air-absorbed moisture ability of the films contributes to heat dissipation by releasing it. The dielectric losses remained below 0.1 in all the composite films, showing their potential for application in electronics. [ABSTRACT FROM AUTHOR]

While organic semiconductors hold significant promise for the development of flexible, lightweight electronic devices such as organic thin-film transistors (OTFTs), photodetectors, and gas sensors, their widespread application is often limited by intrinsic challenges. In this article, we first review these challenges in organic electronics, including low charge carrier mobility, susceptibility to environmental degradation, difficulties in achieving uniform film morphology and crystallinity, as well as issues related to poor interface quality, scalability, and reproducibility that further hinder their commercial viability. Next, we focus on reviewing the hybrid system comprising an organic semiconductor and polystyrene (PS) to address these challenges. By examining the interactions of PS as a polymer additive with several benchmark semiconductors such as pentacene, rubrene, 6,13-bis(triisopropylsilylethynyl) pentacene (TIPS pentacene), 2,8-difluoro-5,11-bis(triethylsilylethynyl) anthradithiophene (diF-TES-ADT), and 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT), we showcase the versatility of PS in enhancing the crystallization, thin film morphology, phase segregation, and electrical performance of organic semiconductor devices. This review aims to highlight the potential of an organic semiconductor/PS hybrid system to overcome key challenges in organic electronics, thereby paving the way for the broader adoption of organic semiconductors in next-generation electronic devices. [ABSTRACT FROM AUTHOR]

In recent years, the charge carrier mobility study of organic semiconductors has seen significant progress and surpassed that of amorphous silicon thanks to the development of various molecular engineering, solution processing, and external alignment methods. These advances have allowed the implementation of organic semiconductors for fabricating high-performance organic electronic devices. In particular, diketopyrrolopyrrole-based small-molecular and polymeric organic semiconductors have garnered considerable research interest due to their ambipolar charge-carrier properties. In this article, we focus on conducting a comprehensive review of previous studies that are dedicated to the external alignment, thermal annealing, and molecular engineering of diketopyrrolopyrrole molecular structures and side-chain structures in order to achieve oriented crystal orientation, optimized thin-film morphology, and enhanced charge carrier transport. By discussing these benchmark studies, this work aims to provide general insights into optimizing other high-mobility, solution-processed organic semiconductors and sheds lights on realizing the acceleration of organic electronic device applications. [ABSTRACT FROM AUTHOR]

Abstract A key component of organic bioelectronics is electrolyte‐gated organic field‐effect transistors (EG‐OFETs), which have recently been used as sensors to demonstrate label‐free, single‐molecule detection. However, these devices exhibit limited stability when operated in direct contact with aqueous electrolytes. Ultrahigh stability is demonstrated to be achievable through the utilization of a systematic multifactorial approach in this study. EG‐OFETs with operational stability and lifetime several orders of magnitude higher than the state of the art have been fabricated by carefully controlling a set of intricate stability‐limiting factors, including contamination and corrosion. The indacenodithiophene‐co‐benzothiadiazole (IDTBT) EG‐OFETs exhibit operational stability that exceeds 900 min in a variety of widely used electrolytes, with an overall lifetime exceeding 2 months in ultrapure water and 1 month in various electrolytes. The devices were not affected by electrical stress‐induced trap states and can remain stable even in voltage ranges where electrochemical doping occurs. To validate the applicability of our stabilized device for biosensing applications, the reliable detection of the protein lysozyme in ultrapure water and in a physiological sodium phosphate buffer solution for 1500 min was demonstrated. The results show that polymer‐based EG‐OFETs are a viable architecture not only for short‐term but also for long‐term biosensing applications.

Abstract There is increasing interest in using specialized circuits based on emerging technologies to develop a new generation of smart devices. The process and device variability exhibited by such materials, however, can present substantial challenges for designing circuits. Three models are considered here: a physical compact model, an empirical look‐up table, and an empirical surrogate model based on a multilayer perceptron (MLP) regression. Each one is fit to measurements of discrete organic thin film transistors in the low voltage regime. It is shown that the models provide consistent results when designing artificial neuron circuits, but that the MLP regression provides the highest accuracy and is much simpler to fit compared to the compact model. The targeted technology exhibits non‐ideal behavior such as variable threshold voltage and hysteresis. Using the MLP regression model, the effect of such variability on the performance of an artificial neuron circuit is compared. It is found that these effects alter the neuron firing rate and change the time spent in the on/off states but do not change the basic operation.

The text discusses the advancements in organic neuromorphic devices and their potential in addressing challenges in neuromorphic computing. It highlights the benefits of organic materials such as flexibility, biocompatibility, and low power consumption for applications in wearable systems and bioelectronics. The document also mentions key research studies presented at the NOD Workshop, focusing on topics like memory stability, device performance optimization, and biosensing applications. Overall, the text emphasizes the importance of interdisciplinary collaboration and innovation in advancing neuromorphic devices for future AI systems. [Extracted from the article]

Diketopyrrolopyrrole (DPP)‐based polymer semiconductors have drawn great attention in the field of organic electronics due to the planar structure, decent solubilizing capability, and high crystallinity. However, the electron‐deficient capacity of DPP derivatives are not strong enough, leading to relatively high‐lying lowest unoccupied molecular orbital (LUMO) energy levels of the corresponding polymers. As a result, n‐type and ambipolar DPP‐based polymers are rare and their electron mobilities also lag far behind the p‐type counterparts, which limits the development of important p‐n‐junction‐based electronic devices. Therefore, new design strategies have been proposed recent years to develop n‐type/ambipolar DPP‐based polymers with improved performances. In this view, these molecular design strategies are summarized, including copolymerization of DPP with different acceptors and weak donors, DPP flanked aromatic ring modification, DPP‐core ring expansion and DPP dimerization. The relationship between the chemical structures and organic thin‐film transistor performances is intensively discussed. Finally, a perspective on future trends in the molecular design of DPP‐based n‐type/ambipolar polymers is also proposed. [ABSTRACT FROM AUTHOR]

Fused-ring electronic acceptors (FREAs) have transformed the field of organic solar cells. However, the prevailing syntheses of FREAs suffer from low yield, difficulty in separation, and high cost. Here, we report new and streamlined syntheses with three distinctive key steps. First, a universal approach to fuse neighboring aromatic units via a single carbon atom is demonstrated with ytterbium triflate and boron trifluoride as the catalysts. This approach allows the incorporation of diverse side-chain combinations. Second, nitrogen atom fusing neighboring aromatics is realized by using oxo-molybdenum catalyst, featuring lower reaction temperatures and enhanced yields. Third, an organic catalyst, proline, is identified to catalyze the aldol condensation with high yield to afford the most typical FREAs having acceptor-donor-acceptor (ADA) configurations. Our new chemistries enable easy syntheses of a wide range of FREAs, substantially expanding the scope and availability of these coveted materials at reduced synthetic cost, particularly for organic electronics. [ABSTRACT FROM AUTHOR]

The introduction of a colorless function to organic electronic devices allows responses to light in the near‐infrared (NIR) region and is expected to broaden the applications of these devices. However, the development of a colorless NIR dye remains a challenge due to the lack of a rational molecular design for controlling electronic transitions. In this study, to suppress the π‐π* transitions in the visible region, polycyclic donor‐acceptor‐donor π‐conjugated molecules with boron bridges (Py‐FNTz‐B and IP‐FNTz‐B) are designed and synthesized, which contain pyrrole or indenopyrrole as donor units with fluorinated naphthobisthiadiazole (FNTz) as an acceptor unit. The pyrrole end‐capped Py‐FNTz‐B shows an absorption band in the NIR region without distinct visible‐light absorption, which has led to the establishment of colorless characteristics. The indenopyrrole end‐capped IP‐FNTz‐B shows a narrow optical energy gap of 0.87 eV in films. Time‐resolved microwave conductance and field‐effect transistors demonstrate the semiconducting characteristics of these molecules, and Py‐FNTz‐B‐based devices function as NIR phototransistors. Theoretical analyses indicate that the combination of a polyene‐like electronic structure with orbital symmetry is important to obtain NIR wavelength‐selective absorption. This study suggests that a molecular design based on electronic structures can be effective in the development of colorless NIR‐absorbing dyes for organic electronics. [ABSTRACT FROM AUTHOR]

The increasing amount of electronic exerts a profound impact on both the environment and human health. Looking forward, it is imperative to develop electronic products that can degrade under mind condition, which largely relies on the development of degradable organic semiconductors (OSCs). Yet, designing degradable OSCs with decent electrical properties is challenging. In this study, two degradable n‐type OSCs based on a dynamic covalent C═C bond formed via the Knoevenagel condensation reaction are reported. The cleavage of Knoevenagel formed C═C bond through a retro‐Knoevenagel process imparts the degradability of these two OSCs in the weak base, particularly in the human‐friendly α‐amino acid of lysine. Meanwhile, the C═C bond formed by Knoevenagel reaction preserves optimal backbone planarity and good electron delocalization of the molecules. This, in turn, endows the OSCs with commendable electron transport performance, achieving an electron mobility of up to 0.57 cm2 V⁻¹ s⁻¹ in organic thin‐film transistors. This work provides a new insight into the molecular design strategy for the development of OSCs with degradability and good electrical properties. [ABSTRACT FROM AUTHOR]

The doping levels of conjugated polymers significantly influence their conductivity, energetics, and optical properties. Recently, a highly conductive n‐doped polymer called poly (3,7‐dihydrobenzo[1,2‐b:4,5‐b′]difuran‐2,6‐dione) (poly(benzodifurandione), n‐PBDF) is discovered, opening new possibilities for n‐type conducting polymers in printed electronics and other fields. Controlling the doping level of n‐PBDF is of great interest due to its wide range of potential applications. Here controlled dedoping and redoping of n‐PBDF is reported and a mechanistic understating of such a process is provided. Dedoping occurs through electron transfer and proton capture, wherein the ionic dopants, tris(4‐bromophenyl)ammoniumyl hexachloroantimonate (Magic Blue), exhibit efficient proton capture ability and stronger interaction with n‐PBDF, resulting in high dedoping efficiency. Moreover, chemically dedoped PBDF can be redoped using various proton‐coupled electron transfer agents. By manipulating the doping levels of n‐PBDF thin films, ranging from highly doped to dedoped states, the system demonstrates controllable conductivity in five orders of magnitude, adjustable optical properties, and energetics. As a result, these characteristics demonstrate the potential applications of n‐PBDF in organic electrochemical transistors and thermoelectrics. [ABSTRACT FROM AUTHOR]

Effective recycling of mixed materials requires the separation of the different components without the need for toxic solvents. One approach involves utilizing a water‐soluble coating with reversible photo‐cross‐linkers, making it robust until end of life where it can then be dissolved in water after de‐cross‐linking. Here, a novel coumarin methacrylate monomer and its nitroxide‐mediated copolymerization to create poly((methacrylic acid)‐co‐(styrene sulfonate)‐co‐(coumarin methacrylate)) for water‐soluble thin films are reported. Under exposure to light, the coumarin functional groups produce reversible [2+2] cycloadditions which cross‐link the resulting polymer films, making them no longer water soluble. Characterization of reversible cross‐linking behavior is reported through changes in contact angle and in situ rheological characterization. The resulting polymers are successfully integrated into metal–insulator–metal capacitors, demonstrating the potential use for water‐soluble reversible photo‐cross‐linkable dielectric materials for organic electronics. [ABSTRACT FROM AUTHOR]

Conjugated polymers consist of complex backbone structures and side‐chain moieties to meet various optoelectronic and processing requirements. Recent work on conjugated polymers has been devoted to studying the mechanical properties and developing new conjugated polymers with low modulus and high‐crack onset strain, while the thin film mechanical stability under long‐term external tensile strain is less investigated. Here we performed direct mechanical stress relaxation tests for both free‐standing and thin film floated on water surface on both high‐Tg and low‐Tg conjugated polymers, as well as a reference nonconjugated sample, polystyrene. We measured thin films with a range of film thickness from 38 to 179 nm to study the temperature and thickness effect on thin film relaxation, where an apparent enthalpy–entropy compensation effect for glassy polymer PS and PM6 thin films was observed. We also compared relaxation times across three different conjugated polymers and showed that both crystalline morphology and higher modulus reduce the relaxation rate besides higher glass transition temperature. Our work provides insights into the mechanical creep behavior of conjugated polymers, which will have an impact on the future design of stable functional organic electronics. [ABSTRACT FROM AUTHOR]

Phosphaphenalenes, extended π conjugates with the incorporation of phosphorus, are attractive avenues towards molecular materials for the applications in organic electronics, but their electron accepting ability have not been investigated. Herein we present systematic studies on the reductive behavior of a representative phosphaphenalene and its oxide by chemical and electrochemical methods. The chemical reduction of the phosphaphenalene by alkali metals reveals the facile P−C bond cleavage to form phosphaphenalenide anion, which functions as a transfer block for structure modification on the phosphorus atom. In contrast, the pentavalent P‐oxide reacts with one or two equivalents of elemental sodium to form stable radical anion and dianion salts, respectively. [ABSTRACT FROM AUTHOR]

Polycyclic aromatic hydrocarbons and their nitrogen‐substituted analogues are of great interest for various applications in organic electronics. The performance of such devices is determined not only by the properties of the single molecules, but also by the structure of their aggregates, which often form via self‐aggregation. Gaining insight into such aggregation processes is a challenging task, but crucial for a fine‐tuning of the materials properties. In this work, an efficient approach for the generation and characterisation of aggregates is described, based on matrix‐isolation experiments and quantum‐chemical calculations. This approach is exemplified for aggregation of acridine. The acridine dimer and trimer are thoroughly analysed on the basis of experimental and calculated UV and IR absorption spectra, which agree well with each other. Thereby a novel structure of the acridine dimer is found, which disagrees with a previously reported one. The calculations also show the changes from excitonic coupling towards orbital interactions between two molecules with decreasing distance to each other. In addition, a structure of the trimer is determined. Finally, an outlook is given on how even higher aggregates can be made accessible through experiment. [ABSTRACT FROM AUTHOR]

This study explores the impact of sulfur oxidation on the structural, optical, and electronic properties of [1]benzothieno[3,2-b][1]benzothiophene (BTBT) derivatives, specifically focusing on 2,7-dibromo BTBT (2,7-diBr-BTBT) and its oxidized forms, 5,5-dioxide (2,7-diBr-BTBTDO) and 5,5,10,10–tetraoxide (2,7-diBr-BTBTTO). The bromination of BTBT followed by sequential oxidation with m-chloroperoxybenzoic acid yielded the target compounds in good yields. They were characterized using a wide array of analytical techniques including different spectroscopic methods, X-ray analysis, thermal analysis, and quantum chemical calculations. The results revealed that sulfur oxidation significantly alters the crystal packing, thermal stability, and optoelectronic properties of BTBT derivatives. Notably, the oxidized forms exhibited increased thermal stability and enhanced emission properties, with quantum yields exceeding 99%. These findings provide valuable insights for designing advanced organic semiconductors and fluorescent materials with tunable properties, based on the BTBT core. [ABSTRACT FROM AUTHOR]

Pure aromatic hydrocarbon materials (PHCs) represent a new generation of host materials for phosphorescent OLEDs (PhOLEDs), free of heteroatoms. They reduce the molecular complexity, can be easily synthesized and are an important direction towards robust devices. As heteroatoms can be involved in bonds dissociations in operating OLEDs through exciton induced degradation processes, developing novel PHCs appear particularly relevant for the future of this technology. In the present work, we report a series of extended PHCs constructed by the assembly of three spirobifluorene fragments. The resulting positional isomers present a high triplet energy level, a wide HOMO/LUMO difference and improved thermal and morphological properties compared to previously reported PHCs. These characteristics are beneficial for the next generation of host materials for PhOLEDs and provide relevant design guidelines. When used as a host in blue‐emitting PhOLEDs, which are still the weakest link of the field, a very high EQE of 24 % and low threshold voltage of 3.56 V were obtained with a low‐efficiency roll‐off. This high performance strengthens the position of PHC strategy as an efficient alternative for OLED technology and opens the way to a more simple electronic. [ABSTRACT FROM AUTHOR]

The adverse aggregated‐caused quenching (ACQ) problem of most electroluminescent materials existing in highly doped thin films is one of the key factors impeding the commercialization of high‐efficiency organic light‐emitting diodes (OLEDs) panel. Whereas, by delicately constructing and modulating moderate intermolecular interactions, some aggregates have been demonstrated to present distinct luminescent properties such as tunable emission spectra, improved photoluminescence quantum yields, different emission mechanism and enhanced horizontal transition dipole ratio (Θ) of emitting layer, providing feasible solution for ACQ problem. The luminescence from newly generated emissive state in aggregates is different from the traditional "isolated" molecules in organic electronics and will possess novel properties and applications. Herein, we summarize the different types of intermolecular interactions within emitter aggregates exhibiting distinct luminescent mechanisms, as well as their effects on photoluminescent and electroluminescent properties, offering reliable reference for the advancement of highly efficient OLEDs utilizing aggregated emitters. [ABSTRACT FROM AUTHOR]

The emergence of cutting‐edge cross‐disciplines has motivated the rapid development of wearable technology and flexible electronics. The flexibility and tunable properties of organic materials enable organic flexible electronics to adapt to complex surface deformations and achieve sensitive detection of physiological signals. The cost‐effectiveness of organic materials in mass production offers additional possibilities for the practical and commercialization of e‐skin technology. However, how to ensure stability and long‐term reliability while maintaining a highly sensitive, flexible, and stretchable is a challenge for e‐skins. In this review, the research progress and development trend of e‐skin is systematically summarized, especially the latest breakthroughs and innovations in the frontier of organic flexible electronics, and systematically review the applications of e‐skin in sensors, physiological monitoring, and energy supply. In addition, the review further discusses the prospects and current challenges for the application of organic flexible electronics in e‐skin, which provides a one‐stop reference for the development of e‐skin. [ABSTRACT FROM AUTHOR]

Increasing demand for bio-interfaced human-machine interfaces propels the development of organic neuromorphic electronics with small form factors leveraging both ionic and electronic processes. Ion-based organic electrochemical transistors (OECTs) showing anti-ambipolarity (OFF-ON-OFF states) reduce the complexity and size of bio-realistic Hodgkin-Huxley(HH) spiking circuits and logic circuits. However, limited stable anti-ambipolar organic materials prevent the design of integrated, tunable, and multifunctional neuromorphic and logic-based systems. In this work, a general approach for tuning anti-ambipolar characteristics is presented through assembly of a p-n bilayer in a vertical OECT (vOECT) architecture. The vertical OECT design reduces device footprint, while the bilayer material tuning controls the anti-ambipolarity characteristics, allowing control of the device's on and off threshold voltages, and peak position, while reducing size thereby enabling tunable threshold spiking neurons and logic gates. Combining these components, a mimic of the retinal pathway reproducing the wavelength and light intensity encoding of horizontal cells to spiking retinal ganglion cells is demonstrated. This work enables further incorporation of conformable and adaptive OECT electronics into biointegrated devices featuring sensory coding through parallel processing for diverse artificial intelligence and computing applications. Stable anti-ambipolar organic materials are limited, thus preventing the design of integrated, tunable, and multifunctional neuromorphic systems. Here, the authors report a small form factor neuromorphic circuit based on organic anti-ambipolar materials, mimicking the pre-processing functions of the retina. [ABSTRACT FROM AUTHOR]

Nanohoops, cyclic association of π‐conjugated systems to form a hoop‐shaped molecule, have been widely developed in the last 15 years. Beyond the synthetic challenge, the strong interest towards these molecules arises from their radially oriented π‐orbitals, which provide singular properties to these fascinating structures. Thanks to their particular cylindrical arrangement, this new generation of curved molecules have been already used in many applications such as host–guest complexation, biosensing, bioimaging, solid‐state emission and catalysis. However, their potential in organic electronics has only started to be explored. From the first incorporation as an emitter in a fluorescent organic light emitting diode (OLED), to the recent first incorporation as a host in phosphorescent OLEDs or as charge transporter in organic field‐effect transistors and in organic photovoltaics, this field has shown important breakthroughs in recent years. These findings have revealed that curved materials can play a key role in the future and can even be more efficient than their linear counterparts. This can have important repercussions for the future of electronics. Time has now come to overview the different nanohoops used to date in electronic devices in order to stimulate the future molecular designs of functional materials based on these macrocycles. [ABSTRACT FROM AUTHOR]

Accurate glucose prediction is vital for diabetes management. Artificial intelligence and artificial neural networks (ANNs) are showing promising results for reliable glucose predictions, offering timely warnings for glucose fluctuations. The translation of these software‐based ANNs into dedicated computing hardware opens a route toward automated insulin delivery systems ultimately enhancing the quality of life for diabetic patients. ANNs are transforming this field, potentially leading to implantable smart prediction devices and ultimately to a fully artificial pancreas. However, this transition presents several challenges, including the need for specialized, compact, lightweight, and low‐power hardware. Organic polymer‐based electronics are a promising solution as they have the ability to implement the behavior of neural networks, operate at low voltage, and possess key attributes like flexibility, stretchability, and biocompatibility. Here, the study focuses on implementing software‐based neural networks for glucose prediction into hardware systems. How to minimize network requirements, downscale the architecture, and integrate the neural network with electrochemical neuromorphic organic devices, meeting the strict demands of smart implants for in‐body computation of glucose prediction is investigated. [ABSTRACT FROM AUTHOR]