Search

Full cost accounting has been applied in many industrial settings that include the oil and gas, energy, chemical and waste management industries. Presently, it is not known how it can be applied in an automotive industry context. Therefore, the objective of this paper is to review existing full cost accounting methods and identify an appropriate approach for the automotive sector. This literature review of 4381 papers extracted ten full cost accounting methods with a diverse level of development and consistency in application. Based on a careful examination and critical analysis of each approach and existing automotive sustainability measures, the Sustainability Assessment Model developed by British Petroleum and Aberdeen University has been proposed as a well-developed and potentially practical tool for automotive applications. The Sustainability Assessment Model can be used by both academics and practitioners to translate a range of conflicting sustainability information into a monetary unit score. This is an effective way of communicating trade-offs and outcomes for complex and multi-disciplinary sustainable decisions in the automotive sector. It measures a broad range of economic, environmental, resource and social effects (internal and external), which is currently lacking in existing automotive systems. Its other strengths are the ability to provide both monetary and physical metrics for sustainability assessment, its flexibility and the ability to combine multiple sustainability dimensions. Furthermore, this paper provides helpful clues for researchers interested in exploring full cost accounting in the future by reviewing, analysing and synthesising the broad range of relevant sources from diverse fields in this topic area.

This paper proposes a robustness analysis based on Multiple Criteria Decision Aiding (MCDA). The ensuing model was used to assess the implementation of green chemistry principles in the synthesis of silver nanoparticles. Its recommendations were also compared to an earlier developed model for the same purpose to investigate concordance between the models and potential decision support synergies. A three-phase procedure was adopted to achieve the research objectives. Firstly, an ordinal ranking of the evaluation criteria used to characterize the implementation of green chemistry principles was identified through relative ranking analysis. Secondly, a structured selection process for an MCDA classification method was conducted, which ensued in the identification of Stochastic Multi-Criteria Acceptability Analysis (SMAA). Lastly, the agreement of the classifications by the two MCDA models and the resulting synergistic role of decision recommendations were studied. This comparison showed that the results of the two models agree between 76% and 93% of the simulation set-ups and it confirmed that different MCDA models provide a more inclusive and transparent set of recommendations. This integrative research confirmed the beneficial complementary use of MCDA methods to aid responsible development of nanosynthesis, by accounting for multiple objectives and helping communication of complex information in a comprehensive and traceable format, suitable for stakeholders and/or decision-makers with diverse backgrounds., Journal of Cleaner Production, 162, ISSN:0959-6526

The first approach utilises a thin film of acrylic that is moulded onto the outside of a polycarbonate substrate. It was found that the gate of the injection mould cavity must be of uniform cross section otherwise local shear heating can occur and melt the acrylic film. The injection gate must also be located entirely on one side of the mould cavity otherwise the film is punctured by the molten polycarbonate and free to float within the cavity. Any mixing of the two materials will lead to opaque components due the difference in the refractive indices. The film was found to improve the UV resistance of any component, acting as a protective buffer for the polycarbonate.\ud \ud A new variety of hardcoat was applied to film-backed samples to impart abrasion resistance and samples were found to outperform commercially available alternatives under recognised laboratory conditions. The film-backed samples also exhibited excellent impact resistance when impacted upon the film-face. However, similar components failed at extremely low energy levels when impacted from the non-film face because flaws in the acrylic film caused cracks to be initiated when the film was placed into tension. The level of adhesion between the film and the polycarbonate has been found to be critical and if the failure mechanism could be guaranteed, then intruder resistant glazing that could be broken from the inside in an emergency becomes a possibility. Such a product would address the identified consumer concern of being trapped in a vehicle.\ud \ud The second approach utilises simultaneous dual injection moulding (2K), which has previously only been used to manufacture coloured components. A successful feasibility study was undertaken to demonstrate the concept of producing transparent components via such a process. This showed that much greater control is required for transparent applications otherwise the skin and core materials mix and opaque components are produced. The generally accepted academic principles associated with the process have been shown to be too simplistic and cannot be relied upon to guarantee good results. The ratio of viscosities of the skin and core materials appear to be more dominant than previously thought and the relative injection speeds of the two materials has a direct influence upon interfacial mixing and haze generation. It was also found that haze could be avoided if the refractive indices of the skin and core material were matched to within ±0.002, but this is impractical.\ud \ud A third area of research examined the feasibility of introducing structured glass fibres weaves into transparent components to improve rigidity. The study resulted in the construction of a transparent glass fibre pre-preg that could be moulded onto the outer surface of polycarbonate components. Flexural tests revealed that a single layer of glass fibre increased the flexural modulus of test samples by a factor of 3, whilst transparency and clarity were retained. Two patents have been filed as a direct result of this work.

During the last few decades, phytoremediation process has attracted much attention because of the growing concerns about the deteriorating quality of soil caused by anthropogenic activities. Here, a tandem phytoremediation/biorefinery process was proposed as a way to turn phytoremediation into a viable commercial method by producing valuable chemicals in addition to cleaned soil. Two agricultural plants (Sinapis alba and Helianthus annuus) were grown in moderately contaminated soil with ca. 100 ppm of Ni and further degraded by a fungal lignin degrader - Phanerochaete chrysosporium. Several parameters have been studied: the viability of plants, biomass yield and their accumulating and remediating potentials. Further down-stream processing showed that up to 80% of Ni can be easily extracted from contaminated biomass by aqueous extraction at mild conditions. Finally, it was demonstrated that the grown onto contaminated soil plants can be degraded by Phanerochaete chrysosporium and the effect of nickel and biomass pre-treatment on the solid state fermentation was studied. The proposed and studied in this work methodology can pave the way to successful commercialization of the phytoremediation process in the near future