Search

The influence of the average surface area of different graphene nanoplatelets (GNP) on the thermo-electrical behaviour, associated with Joule heating, and the attenuation of electromagnetic signals of epoxy composites has been studied, analysing the effect of the morphology obtained as a function of the dispersion time by ultrasonication and the GNP content added. Gravity moulding was used as the first stage in the scaling-up, oriented to the industrial manufacture of multilayer coatings, observing a preferential self-orientation of nanoparticles and, in several conditions, a self-stratification too. The increase of sonication time during the GNP dispersion provides a decrease in the electrical conductivity, due to the GNP fragmentation. Instead, the thermal conductivity is enhanced due to the higher homogeneous distribution of GNPs into the epoxy matrix. Finally, the lower surface area of GNPs reduces the thermal and electrical conductivity due to a greater separation between nanosheets. Regarding the study of the attenuation of electromagnetic waves, it has been discovered that in the frequency range from 100 Hz to 20 MHz, this attenuation is independent of the direction of analysis, the type of graphene, the sonication time, and the state of dispersion of the nano-reinforcement in the matrix. Furthermore, it has also been observed that the conservation of the constant shielding values for the three types of GNPs are in a range of average frequencies between 0.3 and 3 MHz.

The repair performance of the so-called self-healing polymer systems has been extensively studied in recent works. However, the characterization methodology carried out to analyze the repair performance of these materials has not been widely discussed. Herein, a study of the influence of the characterization parameters on the self-healing capabilities of a 2-Aminophenyl disulfide (AFD)/epoxy system via convective heating is carried out. Results show a decrease in the self-healing efficiency proportional to the damage depth. Finally, increasing the healing temperature and time does not significantly affect the repair performance, obtaining similar self-healing efficiency values (>>95%) in all cases.

The present work studies the electrical and electrothermal properties of CNT/GNP-doped nanocomposites for optimizing their anti-icing and de-icing capabilities. Here, a comparison between 3D-printed circuits and coatings based on these materials is carried out. In this regard, the higher electrical conductivity that is achieved by the specimens when increasing the nanoparticle content and the higher cross-sectional area of the coatings with regard to the 3D-printed circuits induces a higher heat generated by the Joule’s effect. Moreover, the successful de-icing test performed by the specimen with the highest self-heating capability, evinces that the studied nanocomposites are suitable for de-icing purposes.

The aim of this study was to analyze whether children with and without difficulties in handwriting, spelling, or both differed in alphabet writing when using a keyboard. The total sample consisted of 1,333 children from Grades 1 through 3. Scores on the spelling and handwriting factors from the "Early Grade Writing Assessment" (Jiménez, in press) were used to assign the participants to one of four groups with different ability patterns: poor handwriters, poor spellers, a mixed group, and typically achieving students. Groups were equalized by a matching strategy, resulting in a final sample of 352 children. A MANOVA was executed to analyze effects of group and grade on orthographic motor integration (fluency of alphabet writing) and the number of omissions when writing the alphabet (accuracy of alphabet writing) by keyboard writing mode. The results indicated that poor handwriters did not differ from typically achieving children in both variables, whereas the poor spellers did perform below the typical achievers and the poor handwriters. The difficulties of poor handwriters seem to be alleviated by the use of the keyboard; however, children with spelling difficulties might need extra instruction to become fluent keyboard writers.

Chromatin remodeling plays a key role in the establishment and maintenance of gene expression patterns essential for plant development and responses to environmental factors. Post-translational modification of histones, including acetylation, is one of the most relevant chromatin remodeling mechanisms that operate in eukaryotic cells. Histone acetylation is an evolutionarily conserved chromatin signature commonly associated with transcriptional activation. Histone acetylation levels are tightly regulated through the antagonistic activity of histone acetyltransferases (HATs) and histone deacetylases (HDACs). In plants, different families of HATs are present, including the MYST family, which comprises homologs of the catalytic subunit of the Nucleosome Acetyltransferase of H4 (NuA4) complex in yeast. This complex mediates acetylation of histones H4, H2A, and H2A.Z, and is involved in transcriptional regulation, heterochromatin silencing, cell cycle progression, and DNA repair in yeast. In Arabidopsis and, other plant species, homologs for most of the yeast NuA4 subunits are present and although the existence of this complex has not been demonstrated yet, compelling evidence supports the notion that this type of HAT complex functions from mosses to angiosperms. Recent proteomic studies show that several Arabidopsis homologs of NuA4 components, including the assembly platform proteins and the catalytic subunit, are associated in vivo with additional members of this complex suggesting that a NuA4-like HAT complex is present in plants. Furthermore, the functional characterization of some Arabidopsis NuA4 subunits has uncovered the involvement of these proteins in the regulation of different plant biological processes. Interestingly, for most of the mutant plants deficient in subunits of this complex characterized so far, conspicuous defects in flowering time are observed, suggesting a role for NuA4 in the control of this plant developmental program. Moreover, the participation of Arabidopsis NuA4 homologs in other developmental processes, such as gametophyte development, as well as in cell proliferation and stress and hormone responses, has also been reported. In this review, we summarize the current state of knowledge on plant putative NuA4 subunits and discuss the latest progress concerning the function of this chromatin modifying complex.

This paper presents a process where carbon fibers and hydrogen can be recovered simultaneously through a two-stage thermal treatment of an epoxy-carbon fiber composite. For this purpose, some pieces of epoxy resin reinforced with carbon fiber fabrics have been fabricated and, after curing, have been pyrolyzed in an installation consisting of two reactors. In the first one, the thermal decomposition of the resin takes place, and in the second one, the gases and vapors coming from the first reactor are thermally treated. Once this process is completed, the solid generated is oxidized with air to eliminate the resin residues and carbonaceous products from the fibers surface. The recovered carbon fiber fabrics have been reused to make new cured parts and their electrical and mechanical properties have been measured. The results show that it is possible to obtain carbon fiber fabrics that can be processed as they leave the recycling process and that retain 80% of the tensile modulus, 70% of the flexural strength, and 50% of the interlaminar shear strength. At the same time, a gaseous stream with more than 66% by volume of hydrogen can be obtained, reaching a maximum of 81.7%.

In this paper, a novel carbon nanotube (CNT) polycaprolactone (PCL), epoxy, and glass fiber (GF) composite is reported. Here, the nanoreinforced composites show a flexural strength increase of around 30%, whereas the interlaminar shear strength increases by 10–15% in comparison to unenhanced samples. This occurs because the addition of the CNTs induces a better PCL/epoxy/GF interaction. Furthermore, the nanoparticles also give novel functionalities to the multiscale composite, such as strain and damage monitoring. Here, the electrical response of the tensile- and compressive-subjected faces was simultaneously measured during flexural tests as well as the transverse conductivity in interlaminar tests, showing an exceptional capability for damage detection. Moreover, it was observed that the electrical sensitivity increases with PCL content due to a higher efficiency of the dispersion process that promotes the creation of a more uniform electrical network.

This work consists of the development of an easy strategy to transform any structure into an efficient surface heater by the application of a low voltage over 3D printed nanocomposite circuits. To this end, the electrical conductivity and self-heating capabilities of UV-Assisted Direct Write 3D printed circuits doped with carbon nanotubes were widely explored as a function of the number of printed layers. Moreover, an optimization of the printing process was carried out by comparing the accuracy and printability obtained when printing with two different configurations: extruding and curing the ink in the same stage or curing the extruded ink in a second stage, after the whole layer was deposited. In this regard, the great homogeneity and repeatability of the heating showed by the four-layer printed circuits, together with their excellent performance for long heating times, proved their applicability to convert any structure to a surface heater. Finally, the deicing capability of the four-layer circuit was demonstrated, being able to remove a 2.5 mm thick ice layer in 4 min and 4 s.

Electrical and electromechanical properties of hybrid graphene nanoplatelet (GNP)/carbon nanotube (CNT)-reinforced composites were analyzed under two different sonication conditions. The electrical conductivity increases with increasing nanofiller content, while the optimum sonication time decreases in a low viscosity media. Therefore, for samples with a higher concentration of GNPs, an increase of sonication time of the hybrid GNP/CNT mixture generally leads to an enhancement of the electrical conductivity, up to values of 3 S/m. This means that the optimum sonication process to achieve the best performances is reached in the longest times. Strain sensing tests show a higher prevalence of GNPs at samples with a high GNP/CNT ratio, reaching gauge factors of around 10, with an exponential behavior of electrical resistance with applied strain, whereas samples with lower GNP/CNT ratio have a more linear response owing to a higher prevalence of CNT tunneling transport mechanisms, with gauge factors of around 3–4.

The pursuit of efficient, profitable, and ecofriendly materials has defined solar cell research from its inception to today. Some materials, such as copper nitride (Cu3N), show great promise for promoting sustainable solar technologies. This study employed reactive radio-frequency magnetron sputtering using a pure nitrogen environment to fabricate quality Cu3N thin films to evaluate how both temperature and gas working pressure affect their solar absorption capabilities. Several characterization techniques, including X-ray diffraction (XRD), Rutherford backscattering spectrometry (RBS), Raman spectroscopy, scanning electron microscopy (SEM), nanoindentation, and photothermal deflection spectroscopy (PDS), were used to determine the main properties of the thin films. The results indicated that, at room temperature, it is possible to obtain a material that is close to stoichiometric Cu3N material (Cu/N ratio ≈ 3) with (100) preferred orientation, which was lost as the substrate temperature increases, demonstrating a clear influence of this parameter on the film structure attributed to nitrogen re-emission at higher temperatures. Raman microscopy confirmed the formation of Cu-N bonds within the 628–637 cm−1 range. In addition, the temperature and the working pressure significantly also influence the film hardness and the grain size, affecting the elastic modulus. Finally, the optical properties revealed suitable properties at lower temperatures, including bandgap values, refractive index, and Urbach energy. These findings underscore the potential of Cu3N thin films in solar energy due to their advantageous properties and resilience against defects. This research paves the way for future advancements in efficient and sustainable solar technologies. [ABSTRACT FROM AUTHOR]

Electromechanical sensing devices, based on resins doped with carbon nanotubes, were developed by digital light processing (DLP) 3D printing technology in order to increase design freedom and identify new future and innovative applications. The analysis of electromechanical properties was carried out on specific sensors manufactured by DLP 3D printing technology with complex geometries: a spring, a three-column device and a footstep-sensing platform based on the three-column device. All of them show a great sensitivity of the measured electrical resistance to the applied load and high cyclic reproducibility, demonstrating their versatility and applicability to be implemented in numerous items in our daily lives or in industrial devices. Different types of carbon nanotubes—single-walled, double-walled and multi-walled CNTs (SWCNTs, DWCNTs, MWCNTs)—were used to evaluate the effect of their morphology on electrical and electromechanical performance. SWCNT- and DWCNT-doped nanocomposites presented a higher Tg compared with MWCNT-doped nanocomposites due to a lower UV light shielding effect. This phenomenon also justifies the decrease of nanocomposite Tg with the increase of CNT content in every case. The electromechanical analysis reveals that SWCNT- and DWCNT-doped nanocomposites show a higher electromechanical performance than nanocomposites doped with MWCNTs, with a slight increment of strain sensitivity in tensile conditions, but also a significant strain sensitivity gain at bending conditions.

A historical research is presented about the foundation and evolution of the Cuban subsidiary of clinical pathology in Cienfuegos, contextualized in antecedents, development and present situation of the clinical laboratories in the province. The most complex and important tasks which were developed by the members of the scientific society from its foundation to the current period are stated, so as future challenges.

A performance mapping of GNP/epoxy composites was developed according to their electromechanical and electrothermal properties for applications as strain sensors and Joule heaters. To achieve this purpose, a deep theoretical and experimental study of the thermal and electrical conductivity of nanocomposites has been carried out, determining the influence of both nanofiller content and sonication time. Concerning dispersion procedure, at lower contents, higher sonication times induce a decrease of thermal and electrical conductivity due to a more prevalent GNP breakage effect. However, at higher GNP contents, sonication time implies an enhancement of both electrical and thermal properties due to a prevalence of exfoliating mechanisms. Strain monitoring tests indicate that electrical sensitivity increases in an opposite way than electrical conductivity, due to a higher prevalence of tunneling mechanisms, with the 5 wt.% specimens being those with the best results. Moreover, Joule heating tests showed the dominant role of electrical mechanisms on the effectiveness of resistive heating, with the 8 wt.% GNP samples being those with the best capabilities. By taking the different functionalities into account, it can be concluded that 5 wt.% samples with 1 h sonication time are the most balanced for electrothermal applications, as shown in a radar chart.

The use of graphene nanoplatelets for several purposes such as barrier properties and structural health monitoring is widely studied in polymer-based coating technology. Nevertheless, their extremely good effect on wear resistance makes them particularly interesting for coating technology. The effect of graphene nanoplatelets addition on the wear behaviour of an epoxy resin was analysed. The effects of graphene nanoplatelets content (0–8 wt.%), morphology and functionalization in wear behaviour were analysed by evaluating the main wear parameters of the nanocomposites studied. The morphology of the wear surfaces was analysed by scanning electron microscopy (SEM) and 3D optical profilometry in order to evaluate the mechanism and severity of wear. The results showed that the wear behaviour of the epoxy resin improved considerably with the addition of graphene, especially for higher contents. Moreover, as the wear mechanism depends on the morphology of graphene nanoplatelets, it was concluded that the proper selection of graphene can be made depending on the chosen application.

Polycaprolactone (PCL) is being researched as a self-healing agent blended with epoxy resins by several reasons: low melting point, differential expansive bleeding (DBE) of PCL, and reaction induced phase separation (RIPS) of PCL/epoxy blends. In this work, PCL/epoxy blends were prepared with different PCL ratios and two different epoxy networks, cured with aliphatic and aromatic amine hardeners. The curing kinetic affects to the blend morphology, varying its critical composition. The self-healing behavior is strongly affected by the blend morphology, reaching the maximum efficiency for co-continuous phases. Blends with dispersed PCL phase into epoxy matrix can also show high self-healing efficiency because of the low PCL domains that act as reservoir of self-healing agent. In this last case, it was confirmed that the most efficient self-healable blends are one whose area occupied by PCL phase is the largest. These blends remain the good thermal and mechanical behavior of epoxy matrix, in contrast to the worsened properties of blends with bicontinuous morphology. In this work, the self-healing mechanism of blends is studied in depth by scanning electron microscopy. Furthermore, the influence of the geometry of the initial surface damage is also evaluated, affecting to the measurement of self-healing efficiency.