Search

This article reports the use of a customized surgical guide for simple and precise C-tube plate placement with minimized incision.Patients who were planning to have orthodontic miniplate treatment because of narrow interradicular space were recruited for this study. A combined silicone and stainless steel wire surgical guide for the C-tube was fabricated on the cast model. The taller wire of the positioning guide is used to accurately start the incision. The incision guide-wire position is verified by placing the miniplate on the coronal horizontal wire to confirm that the incision will coordinate with the screw holes. Because the miniplate is firmly held in place, there is no risk of the miniplate anchoring screws (diameter, 1.5 mm; length, 4 mm) sliding on the bone surface during placement with a manual hand driver.The surgical guide was placed on the clinical site, and it allowed precise placement of the miniplate with minimum incision and preventing from slippage or path-of-insertion angulation errors that might interfere with accurate placement.Customized surgical guide enables precise planning for miniplate positions in anatomically complex sites.

Introduction. The purpose of this study was to investigate effects of surface treatment of mini-implants in diabetes-induced rabbits by comparing osseointegration around mini-implants.Methods. Twelve New Zealand white rabbits were divided into two groups (alloxan-induced diabetic group and control group). A total of 48 mini-implants were placed after four weeks of diabetic induction. 24 mini-implants were surface-treated with SLA (sandblasted with large grit, and acid etched) and the remaining 24 mini-implants had smooth surfaces. Four weeks after placement, 32 mini-implants were removed from 4 control and 4 diabetic rabbits. Insertion and removal torques were measured. The remaining 16 mini-implants from the two groups were histomorphometrically analyzed.Results. Maximum insertion torque showed no difference between diabetic and control groups, but total insertion energy was higher in control group. In surface-treated mini-implants, maximum removal torque was higher in both diabetic and control groups. Bone-implant contact (BIC) was increased in the control group when compared to the diabetic group. Surface-treated group had higher BIC than smooth surface group in both control and diabetic groups. However, there was no significantly statistical difference.Conclusions. Type 1 diabetes mellitus and surface treatment method of mini-implant affected primary stability of mini-implants. In addition, the use of orthodontic mini-implants in a diabetic patient is likely to show results similar to the healthy patient.

Cleidocranial dysplasia (CCD) is a rare congenital disorder characterized by skeletal and dental anomalies. This clinical report describes the prosthodontic approach to treating a CCD patient who presented with decreased facial height and relative mandibular protrusion due to maxillary hypoplasia after orthodontic treatment. Functional and esthetic rehabilitation was achieved using telescopic detachable prostheses in the maxilla and osseointegrated implants and metal-ceramic fixed dental prostheses in the mandible. These treatment approaches precluded the need for orthognathic surgical correction and presented a favorable prognosis during the 5-year observation period.

Implant has been an effective treatment option for the patients with oligodontia. However, it still remains unclear when the implant should be placed. Skeletal growth that can appear even after the growth period can lead to infraocclusion of the implant which can cause functional or esthetic complications. In order to minimize these problems, definitive restorations should be placed after the functional and esthetic rehabilitation is achieved through the use of provisional restorations. Definitive restorations made with monolithic zirconia were created by replicating provisional restorations by using the latest CAD/CAM technology. These definitive restorations were delivered to the patient and clinical observation after the treatment showed satisfactory result. (J Korean Acad Prosthodont 2016;54:28-34)

The aim of this study was to analyze and compare the level and distribution of peri-implant bone stresses associated with mandibular two-implant overdentures with different implant positions.Mathematical models of mandibles and overdentures were designed using finite element analysis software. Two intraosseous implants and ball attachment systems were placed in the interforaminal region. The overdenture, which was supported by the two implants, was designed to withstand bilateral and unilateral vertical masticatory loads (total 100 N). In all, eight types of models, which differed according to assigned implant positions, height of attachments, and angulation, were tested: MI (model with implants positioned in the lateral incisor sites), MC (implants in canine sites), MP (implants in premolar sites), MI-Hi (greater height of attachments), MC-M (canine implants placed with mesial inclination), MC-D (canine implants placed with distal inclination), MC-B (canine implants placed with buccal inclination), and MC-L (canine implants placed with lingual inclination).Peri-implant bone stress levels associated with overdentures retained by lateral incisor implants resulted in the lowest stress levels and the highest efficiency in distributing peri-implant stress. MI-Hi showed increased stress levels and decreased efficiency in stress distribution. As the implants were inclined, stress levels increased and the efficiency of stress distribution decreased. Among the inclined models, MC-B showed the lowest stress level and best efficiency in stress distribution.The lowest stress and the best stability of implants in mandibular two-implant overdentures were obtained when implants were inserted in lateral incisor areas with shorter attachments and were placed parallel to the long axes of the teeth.

Introduction This paper introduces a virtually planned and stereolithographically fabricated guiding system that will allow the clinician to plan carefully for the best location of the device and to achieve an accurate position without complications. Methods The scanned data from preoperative dental casts were edited to obtain preoperative 3-dimensional (3D) virtual models of the dentition. After the 3D virtual models were repositioned, the 3D virtual surgical guide was fabricated. A surgical guide was created onscreen, and then these virtual guides were materialized into real ones using the stereolithographic technique. Results Whereas the previously described guide required laboratory work to be performed by the orthodontist, our technique is more convenient because the laboratory work is done remotely by computer-aided design/computer-aided manufacturing technology. Because the miniplate is firmly held in place as the patient holds his or her mandibular teeth against the occlusal pad of the surgical guide, there is no risk that the miniscrews can slide on the bone surface during placement. The software program (2.5-dimensional software) in this study combines 2-dimensional cephalograms with 3D virtual dental models. This software is an effective and efficient alternative to 3D software when 3D computed tomography data are not available. Conclusions To confidently and safely place a miniplate with screw fixation, a simple customized guide for an orthodontic miniplate was introduced. The use of a custom-made, rigid guide when placing miniplates will minimize complications such as vertical mislocation or slippage of the miniplate during placement.

The purpose of this study was to determine the effect of stabilization splints and mouthguards on the athletic ability of professional golfers. For this study, eight professional golfers with a mean age of 20.5 were selected. These participants performed four trials of 10 driver swings and 10 putts with or without a stabilization splint (control group) or mouthguard. For the 4th trial, the splints were adjusted using a simple blind test so that the participants were unaware of the unilateral molar contact. The drive distance, club head speed, initial ball speed, and putting accuracy were compared and analyzed before and after the application of equal bilateral molar occlusion. When the bilateral molar occlusion was applied using a mouthguard or stabilization splint, the club head speed and driving distance in the presence of the oral appliances were significantly increased compared with those without the presence of either appliance (P0.05). Alternatively, the initial ball speed and putting accuracy in the presence of these appliances were increased compared with those without the presence of an appliance; however, this effect was not statistically significant. When the mouthguards or stabilization splints were adjusted to result in unilateral molar occlusion, the club head speed and driving distance in the presence of the appliances were significantly decreased compared with those that were obtained without these appliances (P0.05). The initial ball speed and the putting accuracy were not affected by the use of the appliances. No difference was observed in the effectiveness of the stabilization splint and mouthguard when bilateral molar occlusion was performed. The occlusion stability that results from stabilization splints and mouthguards is thought to increase the club head speed and driving distance in professional golf players.

BackgroundA previous study on the genetic association between single nucleotide polymorphisms in FGFR1OP2/wit3.0 and the long term atrophy of edentulous mandible hypothesized that the excessive jawbone atrophy after dental extraction may be associated with abnormal oral mucosa contraction induced by the FGFR1OP2/wit 3.0 gene. It was reported that the minor allele of rs840869 or rs859024 in FGFR1OP2/wit3.0 was associated with the excessive atrophy of edentulous mandible. The present study represents an attempt to replicate the results of this previous study and to examine the genetic association between polymorphisms in FGFR1OP2 and residual ridge resorption of mandible in a Korean population.Methodology/principal findings134 subjects (70.46 ± 9.02 years) with partially or completely edentulous mandible were recruited. The mandibular bone height was measured following the protocol of the American College of Prosthodontists (ACP). From 24 subjects, seven variants in FGFR1OP2 were discovered and four of them were novel. Selected SNPs that are not in high LD at r2 threshold of 0.8 were genotyped for the remaining population. There was no frequency of the minor allele of SNP rs859024 in Korean population. SNP rs840869 was not associated with residual ridge resorption (p = 0.479). The bone height of the subject with the ss518063493 minor allele (8.52 mm) was shorter than that of those subjects with major alleles (18.96 ± 5.33 mm, p = 0.053).Conclusions/significanceThe patient with minor allele of ss518063493 may be associated with excessive atrophy of edentulous mandible whereas the patients with that of rs840869 are not associated in Korean population. The result from this study may assist in developing a novel genetic diagnostic test and be useful in identifying Koreans susceptible to developing excessive jawbone atrophy after dental extraction.

심한 잔존치조제의 흡수와 의치지지조직의 손상을 동반한 총의치 난증례는 정확한 진단과 체계적인 치료계획 수립을 통해 보철물의 유지, 안정, 지지를 증진시켜야 한다. Provisional restoration은 총의치의 안정성을 다각도로 평가하고 환자와 치과의사의 피드백을 가능하게 하는 유용한 도구로서 사용될 수 있다. 본 증례에서는 진단용의치를 통해 인상면, 연마면, 교합면을 평가하여 의치의 안정성을 증대시키고 환자의 심미적 요구를 반영하여 최종의치로 이행하였으며 임상적으로 기능과 심미적인 측면에 있어서 만족할 만한 결과를 얻었기에 이를 보고하고자 한다. 【In fully edentulous cases, which are accompanied by severe residual ridge resorption and impairment of supporting tissues of complete dentures, proper diagnosis and systemic treatment planning are required for the improvement in retention, stability, and support of prosthesis. Provisional restoration, while it is unfamiliar in complete denture restoration, can be used as a valuable tool, which makes possible to evaluate the stability of complete dentures and receive feedback from patients in complex clinical situations. In this case, a provisional denture was used to improve stability of impression, polished, and occlusal surfaces of complete denture, and to consider esthetic requirements before final denture construction. The result was clinically satisfactory in terms of functional and esthetical aspects.】

성공적인 보철 치료를 위해서는 정확한 진단이 근거가 되어야 한다. 즉, 처음 환자가 내원하였을 때, 환자의 주소를 바탕으로 한 문제점을 찾고, 그 원인을 분석하여 이에 입각한 치료 계획을 세웠을 때, 만족스러운 결과를 기대할 수 있을 것이다. 본 증례의 환자는 77세 여성으로, 저작 시 상 하악 좌측 소구치 부위의 통증 및 기존 보철물의 비심미성을 주소로 내원하였다. 임상적, 방사선학적 검사 및 모형 분석을 통해 문제점을 파악하였고, 여러 문헌에 근거하여 지대치 평가, 보철물의 여러 가지 디자인에 따른 예후 및 최종 보철물의 장착 시 유지 관리의 용이성 등을 고려하여 치료 계획을 수립하기로 하였다. 심미적 문제, 보철을 위한 악간 공간의 부족을 해소하고자 최소한의 수직 고경 증가를 동반한 전악 수복을 시행하기로 결정하였다. 기능, 심미성 및 교합의 안정을 통한 환자의 적응도를 평가하여 치료 계획의 적절성 여부를 판단할 수 있었다. 따라서, 최종적인 고정성 국소 의치를 제작하고 장착하여 만족스러운 결과를 얻었기에 이를 보고하는 바이다. 【Data collection including checking the problem list and analyzing the etiology cannot be overemphasized in full mouth rehabilitation cases. It is well reported that favorable prognosis of prosthodontic treatment depends on accurate diagnosis. Seventy seven year old female patient presented with chief complaints of chewing pain on maxillary and mandibular left premolars and unesthetic existing prosthesis. Clinical evaluation, radiographic examination and cast analysis were performed to gather comprehensive data and problem lists. Treatment planning was based on collected data and related articles. Abutment evaluation, prognosis depending on various types of prosthesis, and maintenance were considered as well. Occlusal vertical dimension was increased to solve esthetic dissatisfaction and insufficient interocclusal space. Patient adaptation was verified with provisional restorations followed by diagnostic wax up. Function, esthetics and occlusal stability were verified during 8 week follow-up period. Prosthodontic reconstruction based on systemic analysis, diagnosis, and treatment plan led to satisfactory result after delivery of definitive prosthesis.】

This article presents the application of laser welding technique to fabricate an orthodontic mini-implant provisional restoration in missing area after limited orthodontic treatment. A 15-year-old boy case is presented. Two-piece orthodontic C-implant was placed after regaining space for missing right mandibular central incisor. Due to angular deviation of implant, customized abutment was required. Ready-made head part was milled and lingual part of customized abutment was made with non-precious metal. Two parts then were laser welded (Master 1000, Elettrolaser Italy, Verona, Italy) and indirect lab composite (3 M ESPE Sinfony, St. Paul, MN, USA) was built up. The patient had successful result, confirmed by clinical and radiographic examinations. Before the patient is ready to get a permanent restoration later on, this provisional restoration will be used. This case shows that a two-piece orthodontic C-implant system can be used to maintain small edentulous space after orthodontic treatment.