Search

Objective. Deep learning reconstruction (DLR) algorithms exhibit object-dependent resolution and noise performance. Thus, traditional geometric CT phantoms cannot fully capture the clinical imaging performance of DLR. This study uses a patient-derived 3D-printed PixelPrint lung phantom to evaluate a commercial DLR algorithm across a wide range of radiation dose levels. Method. The lung phantom used in this study is based on a patient chest CT scan containing ground glass opacities and was fabricated using PixelPrint 3D-printing technology. The phantom was placed inside two different size extension rings to mimic a small- and medium-sized patient and was scanned on a conventional CT scanner at exposures between 0.5 and 20 mGy. Each scan was reconstructed using filtered back projection (FBP), iterative reconstruction, and DLR at five levels of denoising. Image noise, contrast to noise ratio (CNR), root mean squared error, structural similarity index (SSIM), and multi-scale SSIM (MS SSIM) were calculated for each image. Results. DLR demonstrated superior performance compared to FBP and iterative reconstruction for all measured metrics in both phantom sizes, with better performance for more aggressive denoising levels. DLR was estimated to reduce dose by 25%–83% in the small phantom and by 50%–83% in the medium phantom without decreasing image quality for any of the metrics measured in this study. These dose reduction estimates are more conservative compared to the estimates obtained when only considering noise and CNR. Conclusion. DLR has the capability of producing diagnostic image quality at up to 83% lower radiation dose, which can improve the clinical utility and viability of lower dose CT scans. Furthermore, the PixelPrint phantom used in this study offers an improved testing environment with more realistic tissue structures compared to traditional CT phantoms, allowing for structure-based image quality evaluation beyond noise and contrast-based assessments. [ABSTRACT FROM AUTHOR]

Purpose. Fast kV-switching (FKS) and dual-layer flat-panel detector (DL-FPD) technologies have been actively studied as promising dual-energy spectral imaging solutions for FPD-based cone-beam computed tomography (CT). However, cone-beam CT (CBCT) spectral imaging is known to face challenges in obtaining accurate and robust material discrimination performance. That is because the energy separation by either FKS or DL-FPD, alone, is still limited, along with apparently unpaired signal levels in the effective low- and high-energy projections in real applications, not to mention the x-ray scatter in cone-beam scan which will make the material decomposition almost impossible if no correction is applied. To further improve CBCT spectral imaging capability, this work aims to promote a source-detector joint multi-energy spectral imaging solution which takes advantages of both FKS and DL-FPD, and to conduct a feasibility study on the first tabletop CBCT system with the joint spectral imaging capability developed. Methods. For CBCT, development of multi-energy spectral imaging can be jointly realized by using an x-ray source with a generator whose kilo-voltages can alternate in tens of Hertz (i.e. FKS), and a DL-FPD whose top- and bottom-layer projections corresponds to different effective energy levels. Thanks to the complimentary characteristics inherent in FKS and DL-FPD, the overall energy separation will be significantly better when compared with FKS or DL-FPD alone, and the x-ray photon detection efficiency will be also improved when compared with FKS alone. In this work, a noise performance analysis using the Cramér–Rao lower bound (CRLB) method is conducted. The CRLB for basis material after a projection-domain material decomposition is derived, followed by a set of numerical calculations of CRLBs, for the FKS, the DL-FPD and the joint solution, respectively. To compensate for the slightly angular mismatch between low- and high- projections in FKS, a dual-domain projection completion scheme is implemented. Afterwards material decomposition from the complete projection data is carried out by using the maximum-likelihood method, followed by reconstruction of basis material and virtual monochromatic images (VMI). In this work, the first FKS and DL-FPD jointly enabled multi-energy tabletop CBCT system, to the best of our knowledge, has been developed in our laboratory. To evaluate its spectral imaging performance, a set of physics experiments are conducted, where the multi-energy and head phantoms are scanned using the 80/105/130 kVp switching pairs and projection data are collected using a prototype DL-FPD, whose both top and bottom layer of panels are composed of 550 μ m of cesium iodine (CsI) scintillators with no intermediate metal filter in-between. Results. The numerical simulations show that the joint spectral imaging solution can lead to a significant improvement in energy separation and lower noise levels in most of material decomposition cases. The physics experiments confirmed the feasibility and superiority of the joint spectral imaging, whose CNRs in the selected regions of interest of the multi-energy phantom were boosted by an average improvement of 21.9%, 20.4% for water basis images and 32.8%, 62.8% for iodine images when compared with that of the FKS and DL-FPD, respectively. For the head phantom case, the joint spectral imaging can effectively reduce the streaking artifacts as well, and the standard deviation in the selected regions of interest are reduced by an average decrement of 19.5% and 8.1% for VMI when compared with that of the FKS and DL-FPD, respectively. Conclusions. A feasibility study of the joint spectral imaging solution for CBCT by utilizing both the FKS and DL-FPD was conducted, with the first tabletop CBCT system having such a capability being developed, which exhibits improved CNR and is more effective in avoiding streaking artifacts as expected. [ABSTRACT FROM AUTHOR]

Significance: Photoacoustic computed tomography (PACT) is a promising noninvasive imaging technique for both life science and clinical implementations. To achieve fast imaging speed, modern PACT systems have equipped arrays that have hundreds to thousands of ultrasound transducer (UST) elements, and the element number continues to increase. However, large number of UST elements with parallel data acquisition could generate a massive data size, making it very challenging to realize fast image reconstruction. Although several research groups have developed GPU-accelerated method for PACT, there lacks an explicit and feasible step-by-step description of GPU-based algorithms for various hardware platforms. Aim: In this study, we propose a comprehensive framework for developing GPU-accelerated PACT image reconstruction (GPU-accelerated photoacoustic computed tomography), to help the research community to grasp this advanced image reconstruction method. Approach: We leverage widely accessible open-source parallel computing tools, including Python multiprocessing-based parallelism, Taichi Lang for Python, CUDA, and possible other backends. We demonstrate that our framework promotes significant performance of PACT reconstruction, enabling faster analysis and real-time applications. Besides, we also described how to realize parallel computing on various hardware configurations, including multicore CPU, single GPU, and multiple GPUs platform. Results: Notably, our framework can achieve an effective rate of ~871 times when reconstructing extremely large-scale three-dimensional PACT images on a dual-GPU platform compared to a 24-core workstation CPU. In this paper, we share example codes via GitHub. Conclusions: Our approach allows for easy adoption and adaptation by the research community, fostering implementations of PACT for both life science and medicine. [ABSTRACT FROM AUTHOR]

Image reconstruction problems, like image deblurring and computer tomography, are usually ill-posed and require regularization. A popular approach to regularization is to substitute the original problem with an optimization problem that minimizes the sum of two terms, an ℓ 2 term and an ℓ q term with 0 < q ≤ 1. The first penalizes the distance between the measured data and the reconstructed one, the latter imposes sparsity on some features of the computed solution. In this work, we propose to use the fractional Laplacian of a properly constructed graph in the ℓ q term to compute extremely accurate reconstructions of the desired images. A simple model with a fully automatic method, i.e., that does not require the tuning of any parameter, is used to construct the graph and enhanced diffusion on the graph is achieved with the use of a fractional exponent in the Laplacian operator. Since the fractional Laplacian is a global operator, i.e., its matrix representation is completely full, it cannot be formed and stored. We propose to replace it with an approximation in an appropriate Krylov subspace. We show that the algorithm is a regularization method under some reasonable assumptions. Some selected numerical examples in image deblurring and computer tomography show the performance of our proposal. [ABSTRACT FROM AUTHOR]

Background: Spinal degeneration and vertebral compression fractures are common among the elderly that adversely affect their mobility, quality of life, lung function, and mortality. Assessment of vertebral fractures in chronic obstructive pulmonary disease (COPD) is important due to the high prevalence of osteoporosis and associated vertebral fractures in COPD. Purpose: We present new automated methods for (1) segmentation and labelling of individual vertebrae in chest computed tomography (CT) images using deep learning (DL), multi‐parametric freeze‐and‐grow (FG) algorithm, and separation of apparently fused vertebrae using intensity autocorrelation and (2) vertebral deformity fracture detection using computed vertebral height features and parametric computational modelling of an established protocol outlined for trained human experts. Methods: A chest CT‐based automated method was developed for quantitative deformity fracture assessment following the protocol by Genant et al. The computational method was accomplished in the following steps: (1) computation of a voxel‐level vertebral body likelihood map from chest CT using a trained DL network; (2) delineation and labelling of individual vertebrae on the likelihood map using an iterative multi‐parametric FG algorithm; (3) separation of apparently fused vertebrae in CT using intensity autocorrelation; (4) computation of vertebral heights using contour analysis on the central anterior‐posterior (AP) plane of a vertebral body; (5) assessment of vertebral fracture status using ratio functions of vertebral heights and optimized thresholds. The method was applied to inspiratory or total lung capacity (TLC) chest scans from the multi‐site Genetic Epidemiology of COPD (COPDGene) (ClinicalTrials.gov: NCT00608764) study, and the performance was examined (n = 3231). One hundred and twenty scans randomly selected from this dataset were partitioned into training (n = 80) and validation (n = 40) datasets for the DL‐based vertebral body classifier. Also, generalizability of the method to low dose CT imaging (n = 236) was evaluated. Results: The vertebral segmentation module achieved a Dice score of.984 as compared to manual outlining results as reference (n = 100); the segmentation performance was consistent across images with the minimum and maximum of Dice scores among images being.980 and.989, respectively. The vertebral labelling module achieved 100% accuracy (n = 100). For low dose CT, the segmentation module produced image‐level minimum and maximum Dice scores of.995 and.999, respectively, as compared to standard dose CT as the reference; vertebral labelling at low dose CT was fully consistent with standard dose CT (n = 236). The fracture assessment method achieved overall accuracy, sensitivity, and specificity of 98.3%, 94.8%, and 98.5%, respectively, for 40,050 vertebrae from 3231 COPDGene participants. For generalizability experiments, fracture assessment from low dose CT was consistent with the reference standard dose CT results across all participants. Conclusions: Our CT‐based automated method for vertebral fracture assessment is accurate, and it offers a feasible alternative to manual expert reading, especially for large population‐based studies, where automation is important for high efficiency. Generalizability of the method to low dose CT imaging further extends the scope of application of the method, particularly since the usage of low dose CT imaging in large population‐based studies has increased to reduce cumulative radiation exposure. [ABSTRACT FROM AUTHOR]

Since 2010, there has been little published data on the state of equipment and infrastructure in veterinary radiation oncology clinical practice. These data are important not only to identify the status and use of technology within the veterinary radiation oncology community but also to help identify the extent of medical physics support. The purpose of our study is to report findings from a survey of veterinary radiation oncologists in the USA, Canada, and select centers outside of North America in 2022. A 40‐question survey covering topics such as type of radiotherapy equipment, techniques offered, treatment planning systems and dose calculation algorithms, special techniques, board‐certified radiation oncologists and residents, and extent of medical physics support was distributed through an online survey tool. Results from 40 veterinary radiation oncology institutions, with equipment explicitly used for veterinary care, suggest that the current state of practice is not dissimilar to what currently exists in human radiation oncology facilities; techniques and technologies commonly employed include flattening filter‐free mode megavoltage beams, volumetric arc therapy, daily cone‐beam computed tomography, image‐guided radiation therapy, and sophisticated dose calculation algorithms. These findings suggest the need for modern radiation oncology acceptance testing, commissioning, and quality assurance programs within the veterinary community. The increase in veterinary radiation oncology residency positions and increasing sophistication of equipment suggests that increased levels of standardized medical physics support would benefit the veterinary radiation oncology community. [ABSTRACT FROM AUTHOR]

Penumbral imaging is a technique used in plasma diagnostics in which a radiation source shines through one or more large apertures onto a detector. To interpret a penumbral image, one must reconstruct it to recover the original source. The inferred source always has some error due to noise in the image and uncertainty in the instrument geometry. Interpreting the inferred source thus requires quantification of that inference's uncertainty. Markov chain Monte Carlo algorithms have been used to quantify uncertainty for similar problems but have never been used for the inference of the shape of an image. Because of this, there are no commonly accepted ways of visualizing uncertainty in two-dimensional data. This paper demonstrates the application of the Hamiltonian Monte Carlo algorithm to the reconstruction of penumbral images of fusion implosions and presents ways to visualize the uncertainty in the reconstructed source. This methodology enables more rigorous analysis of penumbral images than has been done in the past. [ABSTRACT FROM AUTHOR]

In recent years, many methods for image super‐resolution (SR) have relied on pairs of low‐resolution (LR) and high‐resolution (HR) images for training, where the degradation process is predefined by bicubic downsampling. While such approaches perform well in standard benchmark tests, they often fail to accurately replicate the complexity of real‐world image degradation. To address this challenge, researchers have proposed the use of unpaired image training to implicitly model the degradation process. However, there is a significant domain gap between the real‐world LR and the synthetic LR images from HR, which severely degrades the SR performance. A novel unsupervised image‐blind super‐resolution method that exploits degradation feature‐based learning for real‐image super‐resolution reconstruction (RDFL) is proposed. Their approach learns the degradation process from HR to LR using a generative adversarial network (GAN) and constrains the data distribution of the synthetic LR with real degraded images. The authors then encode the degraded features into a Transformer‐based SR network for image super‐resolution reconstruction through degradation representation learning. Extensive experiments on both synthetic and real datasets demonstrate the effectiveness and superiority of the RDFL method, which achieves visually pleasing reconstruction results. [ABSTRACT FROM AUTHOR]

Quasi-continuous-phase metasurfaces overcome the side effects imposed by high-order diffraction on imaging and can impart optical parameters such as amplitude, phase, polarization, and frequency to incident light at sub-wavelength scales with high efficiency. Structured-light three-dimensional (3D) imaging is a hot topic in the field of 3D imaging because of its advantages of low computation cost, high imaging accuracy, fast imaging speed, and cost-effectiveness. Structured-light 3D imaging requires uniform diffractive optical elements (DOEs), which could be realized by quasi-continuous-phase metasurfaces. In this paper, we design a quasi-continuous-phase metasurface beam splitter through a vector iterative Fourier transform algorithm and utilize this device to realize structured-light 3D imaging of a target object with subsequent target reconstruction. A structured-light 3D imaging system is then experimentally implemented by combining the fabricated quasi-continuous-phase metasurface illuminated by the vertical-cavity surface-emitting laser and a binocular recognition system, which eventually provides a new technological path for the 3D imaging field. [ABSTRACT FROM AUTHOR]

Purpose: Urolithiasis is a chronic condition that leads to repeated CT scans throughout the patient's life. The goal was to assess the diagnostic performance and image quality of submillisievert abdominopelvic computed tomography (CT) using deep learning-based image reconstruction (DLIR) in urolithiasis. Methods: 57 patients with suspected urolithiasis underwent both non-contrast low-dose (LD) and ULD abdominopelvic CT. Raw image data of ULD CT were reconstructed using hybrid iterative reconstruction (ASIR-V 70%) and high-strength-level DLIR (DLIR-H). The performance of ULD CT for the detection of urinary stones was assessed by two readers and compared with LD CT with ASIR-V 70% as a reference standard. Image quality was assessed subjectively and objectively. Results: 266 stones were detected in 38 patients. Mean effective dose was 0.59 mSv for ULD CT and 1.96 mSv for LD CT. For diagnostic performance, sensitivity and specificity were 89% and 94%, respectively, for ULDCT with DLIR-H. There was an almost perfect intra-observer concordance on ULD CT with DLIR-H versus LDCT with ASIR-V 70% (ICC = 0.90 and 0.90 for the two readers). Image noise was significantly lower and signal-to-noise ratio significantly higher with DLIR-H compared to ASIR-V 70%. Subjective image quality was also significantly better with ULDCT with DLIR-H. Conclusion: ULD CT with Deep Learning Image Reconstruction maintains a good diagnostic performance in urolithiasis, with better image quality than hybrid iterative reconstruction and a significant radiation dose reduction. [ABSTRACT FROM AUTHOR]

This article explores the use of a post-processing technique called noise-based correction (NBC) in electrical impedance tomography (EIT) to improve image quality. The study involves simulations and experiments to test the effectiveness of NBC in reducing noise in reconstructed images. The results show that NBC significantly improves image quality in both 2D and 3D reconstructions, making it a recommended technique for EIT image reconstruction. The authors also suggest that NBC may have applications in other linearized methods in EIT and other impedance imaging techniques. [Extracted from the article]

In poor lighting and rainy and foggy bad weather environments, road traffic signs are blurred and have low recognition, etc. A super-resolution reconstruction algorithm for complex lighting and bad weather traffic sign images was proposed. First, a novel attention residual module was designed to incorporate an aggregated feature attention mechanism on the jump connection side of the base residual module so that the deep network can obtain richer detail information; second, a cross-layer jump connection feature fusion mechanism was adopted to enhance the flow of information across layers as well as to prevent the problem of gradient disappearance of the deep network to enhance the reconstruction of the edge detail information; and lastly, a positive-inverse dual-channel sub-pixel convolutional up-sampling method was designed to reconstruct super-resolution images to obtain better pixel and spatial information expression. The evaluation model was trained on the Chinese traffic sign dataset in a natural scene, and when the scaling factor is 4, the average values of PSNR and SSIM are improved by 0.031 when compared with the latest release of the deep learning-based superresolution reconstruction algorithm for single-frame images, MICU (Multi-level Information Compensation and U-net), the average values of PSNR and SSIM are improved by 0.031 dB and 0.083, and the actual test average reaches 20.946 dB and 0.656. The experimental results show that the reconstructed image quality of this paper's algorithm is better than the mainstream algorithms of comparison in terms of objective indexes and subjective feelings. The super-resolution reconstructed image has a higher peak signal-to-noise ratio and perceptual similarity. It can provide certain technical support for the research of safe driving assistive devices in natural scenes under multi-temporal varying illumination conditions and bad weather. [ABSTRACT FROM AUTHOR]

This paper introduces the Kuopio Tomography Challenge 2023 (KTC 2023), created to inspire and facilitate algorithm development for image reconstruction in electrical impedance tomography (EIT). A laboratory EIT dataset was prepared for the KTC 2023, using conductive and resistive inclusions of various shapes and sizes placed inside a shallow, circular water tank. The task for the competitors of the challenge was to produce segmented images of the inclusions from EIT data in cases of complete coverage of the tank surface with electrodes (lowest level of difficulty) and in cases of decreasing boundary coverage (corresponding to increasing level of challenge difficulty). A total of seven teams, with members from seven countries, participated in KTC 2023, submitting a total of 22 algorithms. The results of the competition show a variety of novel algorithms applied to real EIT data, with high quality image reconstructions from limited boundary data. The EIT data set collected for the challenge is publicly available for future studies on EIT image reconstruction. [ABSTRACT FROM AUTHOR]

Solving systems of nonlinear equations has evolved into an active research field, with numerous iterative methods being proposed. Notably, iterative methods characterized by fast convergence remain of interest. In this paper, based on the modified line search scheme by Ou and Li, we introduce a derivative-free algorithm with a relaxed-inertial technique for approximating solutions of nonlinear systems involving pseudo-monotone mappings in Euclidean space. The global convergence of the proposed algorithm is established without Lipschitz continuity of the underlying mapping. Moreover, our approach allows flexibility in selecting the inertial extrapolation step length within the interval [0, 1]. To show the efficiency of the proposed method, we embed a derivative-free search direction into the scheme. Numerical experiments are given to illustrate the efficiency of the proposed algorithm for large-scale systems and sparse signal reconstruction. [ABSTRACT FROM AUTHOR]

Purpose: To quantify operator dose in interventional CT fluoroscopy (CTF) procedures and compare to catheterization laboratory and interventional radiology procedures. Methods: Fifteen studies quantifying operator scatter dose for c‐arm fluoroscopy and CTF were reviewed from a literature survey. The dose provided in each study was normalized to skin entrance air kerma and air kerma rate including backscatter. The average air kerma rate and exposure duration were calculated and compared between c‐arm fluoroscopy and CTF. To enable operator scatter dose calculations in CTF procedures, a model was created which scaled the dose from a reference condition. Results: Our literature survey indicated that for CTF relative to c‐arm fluoroscopy: (1) the mean air kerma rate is 3.5 times higher, while (2) the mean exposure duration is 31.6 times lower. On average, a physician would have to perform 9.1 times (i.e., 31.6/3.5) more CTF procedures relative to c‐arm fluoroscopy procedure to receive equal operator scatter doses. Our own experimental measurements provided scaling factors allowing physician scatter dose to be obtained at any rotation time, tube current, beam collimation, or beam energy. Conclusion: Our results shed light onto a currently mis‐understood issue in radiology. Namely, that physicians receive more dose from CT relative to c‐arm fluoroscopy motivating them to retreat from the room during interventional exposures. Our literature review and experimental measurements indicate the opposite it true; interventional CT produces on average nine times less physician dose relative to c‐arm procedures. Our method allows for prospective/retrospective determination of an individual's dose. [ABSTRACT FROM AUTHOR]

Electrical Capacitance Tomography (ECT) is one of typical tomography technologies based on capacitance-sensitive fields, which can reconstruct the distribution images of permittivity distribution of different fluid in the measured field and is often used for realizing industrial detection in specific occasions. Landweber and homotopy perturbation regularization algorithms are used for image reconstruction in ECT system, but these algorithms are with many iteration steps, slow convergence speed, and relatively low quality of the reconstructed images. Aiming at these problems, this paper proposes an improved image reconstruction algorithm. Firstly, a regularization term is added to the target function by using the different dielectric constant distribution between the current moment and the previous moment. Then, using the homotopy perturbation to derive the second-order iterative formula to get the homotopy perturbation regularization algorithm, and finally the improved algorithm is obtained by combining the landweber algorithm based on weight factor. Furthermore, the improved homotopy perturbation regularization algorithm is applied for ECT image reconstruction. The numerical simulation experiment results show that the improved algorithm is with the highest comprehensive scores for the four flow patterns of laminar flow, annular flow, core flow and bubble flow, which is higher than the landweber algorithm and the improved homotopy perturbation regularization algorithm by 3% ~ 20%, and 18% ~ 31%, respectively. The relative error, correlation coefficient and subjective effect of the reconstructed image are significantly improved, and it has certain anti-noise performance. These reflect the improved algorithm is with practical value. [ABSTRACT FROM AUTHOR]

Objective. We introduce a robust image reconstruction algorithm named residual-guided Golub–Kahan iterative reconstruction technique (RGIRT) designed for sparse-view computed tomography (CT), which aims at high-fidelity image reconstruction from a limited number of projection views. Approach. RGIRT utilizes an inner-outer dual iteration framework, with a flexible least square QR (FLSQR) algorithm implemented in the inner iteration and a restarted iterative scheme applied in the outer iteration. The inner FLSQR employs a flexible Golub–Kahan bidiagonalization method to reduce the size of the inverse problem, and a weighted generalized cross-validation method to adaptively estimate the regularization hyper-parameter. The inner iteration efficiently yields the intermediate reconstruction result, while the outer iteration minimizes the residual and refines the solution by using the result obtained from the inner iteration. Main results. The reconstruction performance of RGIRT is evaluated and compared to other reference methods (FBPConvNet, SART-TV, and FLSQR) using projection data from both numerical phantoms and real experimental Micro-CT data. The experimental findings, from testing various numbers of projection views and different noise levels, underscore the robustness of RGIRT. Meanwhile, theoretical analysis confirms the convergence of residual for our approach. Significance. We propose a robust iterative reconstruction algorithm for x-ray CT scans with sparse views, thereby shortening scanning time and mitigating excessive ionizing radiation exposure to small animals. [ABSTRACT FROM AUTHOR]

The x-ray radiation dose in computed tomography (CT) examination has been a major concern for patients. Lowing the tube current and exposure time in data acquisition is a straightforward and cost-effective strategy to reduce the x-ray radiation dose. However, this will inevitably increase the noise fluctuations in measured projection data, and the corresponding CT image quality will be severely degraded if noise suppression is not performed during image reconstruction. To reconstruct high-quality low-dose CT image, we present a spatial-radon domain total generalized variation (SRDTGV) regularization for statistical iterative reconstruction based on penalized weighted least-squares (PWLS) principle, which is called PWLS-SRDTGV for simplicity. The presented PWLS-SRDTGV model can simultaneously reconstruct high-quality CT image in space domain and its corresponding projection in radon domain. An efficient split Bregman algorithm was applied to minimize the cost function of the proposed reconstruction model. Qualitative and quantitative studies were performed to evaluate the effectiveness of the PWLS-SRDTGV image reconstruction algorithm using a digital 3D XCAT phantom and an anthropomorphic torso phantom. The experimental results demonstrate that PWLS-SRDTGV algorithm achieves notable gains in noise reduction, streak artifact suppression, and edge preservation compared with competing reconstruction approaches. [ABSTRACT FROM AUTHOR]

Objective. Limited-angle computed tomography (CT) presents a challenge due to its ill-posed nature. In such scenarios, analytical reconstruction methods often exhibit severe artifacts. To tackle this inverse problem, several supervised deep learning-based approaches have been proposed. However, they are constrained by limitations such as generalization issue and the difficulty of acquiring a large amount of paired CT images. Approach. In this work, we propose an iterative neural reconstruction framework designed for limited-angle CT. By leveraging a coordinate-based neural representation, we formulate tomographic reconstruction as a convex optimization problem involving a deep neural network. We then employ differentiable projection layer to optimize this network by minimizing the discrepancy between the predicted and measured projection data. In addition, we introduce a prior-based weight initialization method to ensure the network starts optimization with an informed initial guess. This strategic initialization significantly improves the quality of iterative reconstruction by stabilizing the divergent behavior in ill-posed neural fields. Our method operates in a self-supervised manner, thereby eliminating the need for extensive data. Main results. The proposed method outperforms other iterative and learning-based methods. Experimental results on XCAT and Mayo Clinic datasets demonstrate the effectiveness of our approach in restoring anatomical features as well as structures. This finding was substantiated by visual inspections and quantitative evaluations using NRMSE, PSNR, and SSIM. Moreover, we conduct a comprehensive investigation into the divergent behavior of iterative neural reconstruction, thus revealing its suboptimal convergence when starting from scratch. In contrast, our method consistently produced accurate images by incorporating an initial estimate as informed initialization. Significance. This work showcases the feasibility to reconstruct high-fidelity CT images from limited-angle x-ray projections. The proposed methodology introduces a novel data-free approach to enhance medical imaging, holding promise across various clinical applications. [ABSTRACT FROM AUTHOR]

The hyperspectral image (HSI) distinguishes itself in material identification through its exceptional spectral resolution. However, its spatial resolution is constrained by hardware limitations, prompting the evolution of HSI super-resolution (SR) techniques. Single HSI SR endeavors to reconstruct high-spatial-resolution HSI from low-spatial-resolution inputs, and recent progress in deep learning-based algorithms has significantly advanced the quality of reconstructed images. However, convolutional methods struggle to extract comprehensive spatial and spectral features. Transformer-based models have yet to harness long-range dependencies across both dimensions fully, thus inadequately integrating spatial and spectral data. To solve the above problem, in this paper, we propose a new HSI SR method, SSAformer, which merges the strengths of CNNs and Transformers. It introduces specially designed attention mechanisms for HSI, including spatial and spectral attention modules, and overcomes the previous challenges in extracting and amalgamating spatial and spectral information. Evaluations on benchmark datasets show that SSAformer surpasses contemporary methods in enhancing spatial details and preserving spectral accuracy, underscoring its potential to expand HSI's utility in various domains, such as environmental monitoring and remote sensing. [ABSTRACT FROM AUTHOR]

The Kaczmarz algorithm is widely used in image reconstruction. In this paper, we propose an enhanced version of the Kaczmarz algorithm by integrating Nesterov momentum into the Kaczmarz algorithm, denoted as the Kaczmarz algorithm with momentum. Our innovation offers a novel approach to accelerate the convergence rate of the Kaczmarz algorithm significantly. Based on greedy rules for selecting work row, we prove that the Kaczmarz method with momentum can achieve global linear convergence rates. Furthermore, we extend a constrained version of the Kaczmarz algorithm with Nesterov momentum for improved image reconstruction and prove its convergence. Numerical experiments show that the proposed algorithm outperforms the original Kaczmarz algorithm in terms of efficiency for image reconstruction. [ABSTRACT FROM AUTHOR]

Objective. 3D cine-magnetic resonance imaging (cine-MRI) can capture images of the human body volume with high spatial and temporal resolutions to study anatomical dynamics. However, the reconstruction of 3D cine-MRI is challenged by highly under-sampled k-space data in each dynamic (cine) frame, due to the slow speed of MR signal acquisition. We proposed a machine learning-based framework, spatial and temporal implicit neural representation learning (STINR-MR), for accurate 3D cine-MRI reconstruction from highly under-sampled data. Approach. STINR-MR used a joint reconstruction and deformable registration approach to achieve a high acceleration factor for cine volumetric imaging. It addressed the ill-posed spatiotemporal reconstruction problem by solving a reference-frame 3D MR image and a corresponding motion model that deforms the reference frame to each cine frame. The reference-frame 3D MR image was reconstructed as a spatial implicit neural representation (INR) network, which learns the mapping from input 3D spatial coordinates to corresponding MR values. The dynamic motion model was constructed via a temporal INR, as well as basis deformation vector fields (DVFs) extracted from prior/onboard 4D-MRIs using principal component analysis. The learned temporal INR encodes input time points and outputs corresponding weighting factors to combine the basis DVFs into time-resolved motion fields that represent cine-frame-specific dynamics. STINR-MR was evaluated using MR data simulated from the 4D extended cardiac-torso (XCAT) digital phantom, as well as two MR datasets acquired clinically from human subjects. Its reconstruction accuracy was also compared with that of the model-based non-rigid motion estimation method (MR-MOTUS) and a deep learning-based method (TEMPEST). Main results. STINR-MR can reconstruct 3D cine-MR images with high temporal (<100 ms) and spatial (3 mm) resolutions. Compared with MR-MOTUS and TEMPEST, STINR-MR consistently reconstructed images with better image quality and fewer artifacts and achieved superior tumor localization accuracy via the solved dynamic DVFs. For the XCAT study, STINR reconstructed the tumors to a mean ± SD center-of-mass error of 0.9 ± 0.4 mm, compared to 3.4 ± 1.0 mm of the MR-MOTUS method. The high-frame-rate reconstruction capability of STINR-MR allows different irregular motion patterns to be accurately captured. Significance. STINR-MR provides a lightweight and efficient framework for accurate 3D cine-MRI reconstruction. It is a 'one-shot' method that does not require external data for pre-training, allowing it to avoid generalizability issues typically encountered in deep learning-based methods. [ABSTRACT FROM AUTHOR]

Diffuse correlation tomography (DCT) is an emerging tissue blood flow index (BFI) imaging technique that typically requires a large number of source‐detector pairs, resulting in high instrumentation costs. We developed a low‐cost paradigm for upgrading the DCT system with time‐sharing hardware sensors via optical switches, wherein the S‐D configuration was spatially optimized and combined with a novelty Nth‐order linear algorithm for image reconstruction. We verified this system through the phantom experiment and the lower limb skeletal muscle cuff occlusion test. The reconstructed BFI images exhibit the excellent performance of the upgraded DCT system in retrieval of the target location, outline, and anomaly contrast. For the deepest quasi‐solid anomaly, location accuracy was 90% with the αDB‐contrast of 0.75. While, for the deepest liquid tube anomaly, a good linear relationship was achieved between contrast and pump speed, with the αDB‐contrast of 3.29 at 600 mL/h. For human experiments, it was found that the BFI in the relaxed state was ten times higher than in the cuff occlusion state. This study demonstrates the feasibility of the proposed upgraded low‐cost DCT system for diagnosing various diseases associated with local perfusion abnormalities. [ABSTRACT FROM AUTHOR]

Standard beams are mainly used for the calibration of strain sensors using their load reconstruction models. However, as an ill-posed inverse problem, the solution to these models often fails to converge, especially when dealing with dynamic loads of different frequencies. To overcome this problem, a piecewise Tikhonov regularization method (PTR) is proposed to reconstruct dynamic loads. The transfer function matrix is built both using the denoised excitations and the corresponding responses. After singular value decomposition (SVD), the singular values are divided into submatrices of different sizes by utilizing a piecewise function. The regularization parameters are solved by optimizing the piecewise submatrices. The experimental result shows that the MREs of the PTR method are 6.20% at 70 Hz and 5.86% at 80 Hz. The traditional Tikhonov regularization method based on GCV exhibits MREs of 28.44% and 29.61% at frequencies of 70 Hz and 80 Hz, respectively, whereas the L-curve-based approach demonstrates MREs of 29.98% and 18.42% at the same frequencies. Furthermore, the PREs of the PTR method are 3.54% at 70 Hz and 3.73% at 80 Hz. The traditional Tikhonov regularization method based on GCV exhibits PREs of 27.01% and 26.88% at frequencies of 70 Hz and 80 Hz, respectively, whereas the L-curve-based approach demonstrates PREs of 29.50% and 15.56% at the same frequencies. All in all, the method proposed in this paper can be extensively applied to load reconstruction across different frequencies. [ABSTRACT FROM AUTHOR]

Background: Robotic C‐arm cone‐beam computed tomography (CBCT) scanners provide fast in‐room imaging in radiotherapy. Their mobility extends beyond performing a gantry rotation, but they might encounter obstructions to their motion which limit the gantry angle range. The axial field‐of‐view (FOV) of a reconstructed CBCT image depends on the acquisition geometry. When imaging a large anatomical location, such as the thorax, abdomen, or pelvis, a centered cone beam might be insufficient to acquire untruncated projection images. Some CBCT scanners can laterally displace their detector and collimate the beam to increase the FOV, but the gantry must then perform a 360∘$360^{\circ}$ rotation to provide complete data for reconstruction. Purpose: To extend the FOV of a CBCT image with a single short scan (gantry angle range of 180∘+$180^{\circ}+$ fan angle) using two complementary short scans. Methods: We defined an acquisition protocol using two short scans during which the source follows the same trajectory and where the detector has equal and opposite tilt and/or offset between the two scans, which we refer to as complementary scans. We created virtual acquisitions using a Monte Carlo simulator on a digital anthropomorphic phantom and on a computed tomography (CT) scan of a patient abdomen. For our proposed method, each simulation produced two complementary sets of projections, which were weighted for redundancies and used to reconstruct one CBCT image. We compared the resulting images to the ground truth phantoms and simulations of conventional scans. Results: Reconstruction artifacts were slightly more prominent in the complementary scans w.r.t. a complete scan with untruncated projections but matched those in a single short scan without truncation. When analyzing reconstructed scans from simulated projections with scatter and corrected with prior CT information, we found a global agreement between complementary and conventional scan approaches. Conclusions: When dealing with a limited range of motion of the gantry of a CBCT scanner, two complementary short scans are a technically valid alternative to a full 360∘$^{\circ}$ scan with equal FOV. This approach enables FOV extension without collisions or hardware upgrades. [ABSTRACT FROM AUTHOR]

Tensor wheel (TW) decomposition is an elegant compromise of the popular tensor ring decomposition and fully connected tensor network decomposition, and it has many applications. In this work, we investigate the computation of this decomposition. Three randomized algorithms based on random sampling or random projection are proposed. Specifically, by defining a new tensor product called the subwheel product, the structures of the coefficient matrices of the alternating least squares subproblems from the minimization problem of TW decomposition are first figured out. Then, using the structures and the properties of the subwheel product, a random sampling algorithm based on leverage sampling and two random projection algorithms respectively based on Kronecker subsampled randomized Fourier transform and TensorSketch are derived. These algorithms can implement the sampling and projection on TW factors and hence can avoid forming the full coefficient matrices of subproblems. We present the complexity analysis and numerical performance on synthetic data, real data, and image reconstruction for our algorithms. Experimental results show that, compared with the deterministic algorithm in the literature, they need much less computing time while achieving similar accuracy and reconstruction effect. We also apply the proposed algorithms to tensor completion and find that the sampling-based algorithm always has excellent performance and the projection-based algorithms behave well when the sampling rate is higher than 50%. [ABSTRACT FROM AUTHOR]

This letter was to present an attempt of large‐wavelength Gaussian deconvolution phase‐contrast computed tomography (LW‐GD‐PCCT) for promotion of image quality reconstructed in low‐frequency band of terahertz (THz) spectrum at 0.11 THz. The interaction between the imaging samples and the THz Gaussian beam were formulated firstly in this paper, where the unwrapped phase was extracted specifically to portray the spatial structure distribution of the samples. Additionally, a Gaussian deconvolution was employed for the further reduction of spatial distortions. Moreover, an image reconstruction was carried out with the obtained phase sinograms based on phase‐used inverse Radon transform from the different positions on the sample. For an experimental assessment of the concept of LW‐GD‐PCCT, a single ellipsoid reflector‐based THz Gaussian beam generating system was established and samples such as polystyrene (PS) foam cuboid (Sample 1), and cylinder (Sample 2) with hollow defects (air holes and triangles) were prepared carefully in this work. To experimentally evaluate the performance of the contributing to the structural imaging over soft samples. Two‐dimensional topographies of each sample were reconstructed successfully, and the obtained cross root‐mean‐square error (cross‐RMSE), cross peak signal‐to‐noise ratio (cross‐PSNR), and cross structural similarity (cross‐SSIM) were 151.6451, 26.3225, and 0.9616 for Sample 1 with a high dose of 180 projections respectively, as well as 30.3242, 33.3129, and 0.9711 for Sample 2 with a low dose of 36 projections, respectively. The obtained imaging indicators of this work showed a superiority of imaging quality over those of recent works. Furthermore, the investigation of the bearing capacity has shown promise in enhancing image quality even in low‐dose conditions. The presented results suggest that the unwrapped phase combining with Gaussian deconvolution in low‐frequency band of THz imaging would be useful to improve the reconstructed image quality, potential to highly feasible non‐destructive testing of polymer foam via large wavelength. [ABSTRACT FROM AUTHOR]

This paper proposes a super‐resolution reconstruction model, SRPGANto improve the visual quality of images based on generative adversarial networks (GANs) by improving the network structures of the generator and the discriminator. In the generator, a dual branch residual block is designed instead of the residual block, including a branch with an attention mechanism and a branch without an attention mechanism, to extract more differentiated features. Normalization methods are explored to avoid unstable training and bath normalization artifacts and use a half instance normalization layer that is more suitable for underlying visual problems compared with traditional batch normalization. In the discriminator, PatchGAN is applied instead of typical GAN to improve the generation of local texture by discriminating each patch rather than the global image. The experimental results on the public datasets demonstrate that the proposed SRPGAN can achieve excellent quantitative evaluation while improving the visual quality of reconstructed images. [ABSTRACT FROM AUTHOR]

To introduce a new cross-domain complex convolution neural network for accurate MR image reconstruction from undersampled k-space data. Most reconstruction methods utilize neural networks or cascade neural networks in either the image domain and/or the k-space domain. However, these methods encounter several challenges: 1) Applying neural networks directly in the k-space domain is suboptimal for feature extraction; 2) Classic image-domain networks have difficulty in fully extracting texture features; and 3) Existing cross-domain methods still face challenges in extracting and fusing features from both image and k-space domains simultaneously. In this work, we propose a novel deep-learning-based 2-D single-coil complex-valued MR reconstruction network termed TEID-Net. TEID-Net integrates three modules: 1) TE-Net, an image-domain-based sub-network designed to enhance contrast in input features by incorporating a Texture Enhancement Module; 2) ID-Net, an intermediate-domain sub-network tailored to operate in the image-Fourier space, with the specific goal of reducing aliasing artifacts realized by leveraging the superior incoherence property of the decoupled one-dimensional signals; and 3) TEID-Net, a cross-domain reconstruction network in which ID-Nets and TE-Nets are combined and cascaded to boost the quality of image reconstruction further. Extensive experiments have been conducted on the fastMRI and Calgary-Campinas datasets. Results demonstrate the effectiveness of the proposed TEID-Net in mitigating undersampling-induced artifacts and producing high-quality image reconstructions, outperforming several state-of-the-art methods while utilizing fewer network parameters. The cross-domain TEID-Net excels in restoring tissue structures and intricate texture details. The results illustrate that TEID-Net is particularly well-suited for regular Cartesian undersampling scenarios. [ABSTRACT FROM AUTHOR]

This article discusses a novel approach to non-invasive skin cancer diagnosis using graphene electrical tattoos and electrical impedance tomography (EIT). The authors propose a system that combines EIT with graphene electronic tattoos (GETs) to differentiate between benign and malignant skin lesions based on impedance differences. The feasibility of the system is demonstrated through computational and experimental models. This approach has the potential to provide rapid and accurate skin cancer diagnosis without invasive procedures. The article also provides a list of references related to skin cancer detection and diagnosis using electrical impedance techniques, which can be valuable resources for further research. [Extracted from the article]

OBJECTIVES: To evaluate the performance of deep learning image reconstruction (DLIR) algorithm in dual-energy spectral CT (DEsCT) as a function of radiation dose and image energy level, in comparison with filtered-back-projection (FBP) and adaptive statistical iterative reconstruction-V (ASIR-V) algorithms. METHODS: An ACR464 phantom was scanned with DEsCT at four dose levels (3.5 mGy, 5 mGy, 7.5 mGy, and 10 mGy). Virtual monochromatic images were reconstructed at five energy levels (40 keV, 50 keV, 68 keV, 74 keV, and 140 keV) using FBP, 50% and 100% ASIR-V, DLIR at low (DLIR-L), medium (DLIR-M), and high (DLIR-H) settings. The noise power spectrum (NPS), task-based transfer function (TTF) and detectability index (d') were computed and compared among reconstructions. RESULTS: NPS area and noise increased as keV decreased, with DLIR having slower increase than FBP and ASIR-V, and DLIR-H having the lowest values. DLIR had the best 40 keV/140 keV noise ratio at various energy levels, DLIR showed higher TTF (50%) than ASIR-V for all materials, especially for the soft tissue-like polystyrene insert, and DLIR-M and DLIR-H provided higher d' than DLIR-L, ASIR-V and FBP in all dose and energy levels. As keV increases, d' increased for acrylic insert, and d' of the 50 keV DLIR-M and DLIR-H images at 3.5 mGy (7.39 and 8.79, respectively) were higher than that (7.20) of the 50 keV ASIR-V50% images at 10 mGy. CONCLUSIONS: DLIR provides better noise containment for low keV images in DEsCT and higher TTF(50%) for the polystyrene insert over ASIR-V. DLIR-H has the lowest image noise and highest detectability in all dose and energy levels. DEsCT 50 keV images with DLIR-M and DLIR-H show potential for 65% dose reduction over ASIR-V50% withhigher d'. [ABSTRACT FROM AUTHOR]

For the significant distortion problem caused by the special projection method of equi-rectangular projection (ERP) images, this paper proposes an omnidirectional image super-resolution algorithm model based on position information transformation, taking SwinIR as the base. By introducing a space position transformation module that supports deformable convolution, the image preprocessing process is optimized to reduce the distortion effects in the polar regions of the ERP image. Meanwhile, by introducing deformable convolution in the deep feature extraction process, the model's adaptability to local deformations of images is enhanced. Experimental results on publicly available datasets have shown that our method outperforms SwinIR, with an average improvement of over 0.2 dB in WS-PSNR and over 0.030 in WS-SSIM for ×4 pixel upscaling. [ABSTRACT FROM AUTHOR]

The benefits of having digital twins of urban buildings are numerous. However, a major difficulty encountered in their creation from airborne LiDAR point clouds is the effective means of accurately reconstructing significant occlusions amidst point density variations and noise. To bridge the noise/sparsity/occlusion gap and generate high fidelity 3D building models, we propose APC2Mesh which integrates point completion into a 3D reconstruction pipeline, enabling the learning of dense geometrically accurate representation of buildings. Specifically, we leveraged complete points generated from occluded ones as input to a linearized skip attention-based deformation network for 3D mesh reconstruction. In our experiments, conducted on 3 different scenes, we demonstrate that: (1) Compared to SoTA methods like NDF, Points2Poly, Point2Mesh, and a few others, APC2Mesh ranked second in positional RMSE and first in directional RSME, with error magnitudes of 0.0134 m and 0.1581, respectively. This indicates the efficacy of APC2Mesh in handling the challenges of airborne building points of diverse styles and complexities. (2) The combination of point completion with typical deep learning-based 3D point cloud reconstruction methods offers a direct and effective solution for reconstructing significantly occluded airborne building points. As such, this neural integration holds promise for advancing the creation of digital twins for urban buildings with greater accuracy and fidelity. Our source code is available at https://github.com/geospatial-lab/APC2Mesh. [ABSTRACT FROM AUTHOR]

Gas–solid Fluidized bed technology has a pivotal role in coal separation. Bubble movement behavior is an important factor affecting the fluidization stability. Fluidized bed measurement is an essential link in the bubble behavior study. As the main evaluation parameters, the concentration distribution and density distribution can reflect the bubble movement behavior. This work uses a noninvasive method of electrical capacitance tomography (ECT) for fluidized bed measurements, combined with COMSOL simulation validation for real-time imaging of bubbles in Geldart Group B magnetite powder particles. Meanwhile, the most suitable reconstruction algorithm for gas–solid separation fluidized bed is selected from three image reconstruction algorithms. And then concentration distribution and density distribution are analyzed. The results show that under reasonable gas velocity conditions (U–Umf =2.28 and 3.17 cm/s), the central region ([0, 1/4]) concentrations of [0.43–0.45] and [0.39–0.42] and densities of [1.98–2.06 g/cm3] and [1.86–1.96 g/cm3] are obtained by ECT measurements, respectively. Finally, the bed density obtained from the ECT sensors in the experiment was validated using three different bed density models. The error can be controlled to within 20%, which indicates that the ECT measurement method has a fairly high reliability and accuracy in dry coal beneficiation field. [ABSTRACT FROM AUTHOR]

To precisely estimate blur kernels (BKs) and obtain high-quality latent images (LIs), we present an efficient blind image deblurring (BID) algorithm via a gradient prior and an enhanced sparse prior. The proposed algorithm decomposes BID into two phases: multiscale blur estimation (MSBE) and image deconvolution (ID). The former focuses on precise BKs, whereas the latter focuses on high-quality LIs. In the MSBE phase, significant image gradients and an enhanced sparse prior are used to estimate BKs. To this end, we build an MSBE model using a hyper-Laplacian gradient (HLG) prior and sparsity-inducing l2,1-regularization. l2,1-regularization imposes enhanced sparsity on the BKs to be estimated, and the HLG prior characterizes the true distribution of image gradients. We use a method derived from half-quadratic splitting (HQS) to handle the built MSBE model by decoupling it into simpler subproblems. Subsequently, these subproblems are solved by efficient and concise methods. In the MSBE phase, we also adopt a multiscale process to avoid local optima of the estimated BKs and adaptively update a penalty parameter to accelerate the iteration. In the ID phase, SotA restoration algorithms are employed by the proposed BID algorithm to obtain competitive final LIs. The experiments are conducted on several baseline datasets to evaluate our BID algorithm. Under the evaluation criteria of success-rate (SR), SSDE, PSNR, SSIM, vision effect, and running time (RT), our study shows apparent advantages compared with some SotA BID algorithms. These advantages include but are not limited to reducing the RT; obtaining higher PSNRs, SSIMs, and SRs; decreasing SSDEs; and obtaining high-quality LIs without artifacts. [ABSTRACT FROM AUTHOR]

A novel and highly efficient computational framework for reconstructing binary-type images suitable for models of various complexity seen in diverse biomedical applications is developed and validated. Efficiency in computational speed and accuracy is achieved by combining the advantages of recently developed optimization methods that use sample solutions with customized geometry and multiscale control space reduction, all paired with gradient-based techniques. The control space is effectively reduced based on the geometry of the samples and their individual contributions. The entire 3-step computational procedure has an easy-to-follow design due to a nominal number of tuning parameters making the approach simple for practical implementation in various settings. Fairly straightforward methods for computing gradients make the framework compatible with any optimization software, including black-box ones. The performance of the complete computational framework is tested in applications to 2D inverse problems of cancer detection by electrical impedance tomography (EIT) using data from models generated synthetically and obtained from medical images showing the natural development of cancerous regions of various sizes and shapes. The results demonstrate the superior performance of the new method and its high potential for improving the overall quality of the EIT-based procedures. [ABSTRACT FROM AUTHOR]

Image reconstruction in multispectral computed tomography (MSCT) requires solving a challenging nonlinear inverse problem, commonly tackled via iterative optimization algorithms. Existing methods necessitate computing the derivative of the forward map and potentially its regularized inverse. In this work, we present a simple yet highly effective algorithm for MSCT image reconstruction, utilizing iterative update mechanisms that leverage the full forward model in the forward step and a derivative-free adjoint problem. Our approach demonstrates both fast convergence and superior performance compared to existing algorithms, making it an interesting candidate for future work. We also discuss further generalizations of our method and its combination with additional regularization and other data discrepancy terms. [ABSTRACT FROM AUTHOR]

The orthogonal moments giving relevant results of these last years within the framework of object detection, pattern recognition and image reconstruction, this work based on orthogonal functions called Orthogonal Jacobi Polynomials (OJPs), and we introduce a new set of moments called Generalized Jacobi Fourier Moments (GJFMs), these polynomials are characterized by parameters α,β and λ. However, it was very important to optimize these parameters in order to obtain a good result, in this context; this study used a new approach to optimized Jacobi Fourier parameters α,β and λ using the artificial bee colony algorithm (ABC) in order to improves the quality of reconstruction of images of large sizes. On the one hand, to validate this technique which offers a high image reconstruction quality. On other hand, the comparison carried out with other algorithms clearly indicates the advantage of the proposed method. [ABSTRACT FROM AUTHOR]

The reconstruction of three-dimensional scenes from a single image represents a significant challenge in computer vision, particularly in the context of cultural heritage digitisation, where datasets may be limited or of poor quality. This paper addresses this challenge by conducting a study of the latest and most advanced algorithms for single-image 3D reconstruction, with a focus on applications in cultural heritage conservation. Exploiting different single-image datasets, the research evaluates the strengths and limitations of various artificial intelligence-based algorithms, in particular Neural Radiance Fields (NeRF), in reconstructing detailed 3D models from limited visual data. The study includes experiments on scenarios such as inaccessible or non-existent heritage sites, where traditional photogrammetric methods fail. The results demonstrate the effectiveness of NeRF-based approaches in producing accurate, high-resolution reconstructions suitable for visualisation and metric analysis. The results contribute to advancing the understanding of NeRF-based approaches in handling single-image inputs and offer insights for real-world applications such as object location and immersive content generation. [ABSTRACT FROM AUTHOR]

Large-area image acquisition techniques are essential in underwater investigations: high-resolution 3D image-based reconstructions have improved coral reef monitoring by enabling novel seascape ecological analysis. Artificial intelligence (AI) offers methods for significantly accelerating image data interpretation, such as automatically recognizing, enumerating, and measuring organisms. However, the rapid proliferation of these technological achievements has led to a relative lack of standardization of methods. Remarkably, there are notable differences in procedures for generating human and AI annotations, and there is also a scarcity of publicly available datasets and shared machine-learning models. The lack of standard procedures makes it challenging to compare and reproduce scientific findings. One way to overcome this problem is to make the most used platforms by coral reef scientists interoperable so that the analyses can all be exported into a common format. This paper introduces functionality to promote interoperability between three popular open-source software tools dedicated to the digital study of coral reefs: TagLab, CoralNet, and Viscore. As users of each platform may have different analysis pipelines, we discuss several workflows for managing and processing point and area annotations, improving collaboration among these tools. Our work sets the foundation for a more seamless ecosystem that maintains the established investigation procedures of various laboratories but allows for easier result sharing. [ABSTRACT FROM AUTHOR]

The single-image super-resolution task benefits has a wide range of application scenarios, so has long been a hotspot in the field of computer vision. However, designing a continuous-scale super-resolution algorithm with excellent performance is still a difficult problem to solve. In order to solve this problem, we propose a continuous-scale SR algorithm based on a Transformer, which is called residual dense Swin Transformer (RDST). Firstly, we design a residual dense Transformer block (RDTB) to enhance the information flow before and after the network and extract local fusion features. Then, we use multilevel feature fusion to obtain richer feature information. Finally, we use the upsampling module based on the local implicit image function (LIIF) to obtain continuous-scale super-resolution results. We test RDST on multiple benchmarks. The experimental results show that RDST achieves SOTA performance in the fixed scale of super-resolution tasks in the distribution, and significantly improves (0.1∼0.6 dB) the arbitrary scale of super-resolution tasks out of distribution. Sufficient experiments show that our RDST can use fewer parameters, and its performance is better than the SOTA SR method. [ABSTRACT FROM AUTHOR]

Image fusion plays a significant role in computer vision since numerous applications benefit from the fusion results. The existing image fusion methods are incapable of perceiving the most discriminative regions under varying illumination circumstances and thus fail to emphasize the salient targets and ignore the abundant texture details of the infrared and visible images. To address this problem, a multiscale aggregation and illumination‐aware attention network (MAIANet) is proposed for infrared and visible image fusion. Specifically, the MAIANet consists of four modules, namely multiscale feature extraction module, lightweight channel attention module, image reconstruction module, and illumination‐aware module. The multiscale feature extraction module attempts to extract multiscale features in the images. The role of the lightweight channel attention module is to assign different weights to each channel so as to focus on the essential regions in the infrared and visible images. An illumination‐aware module is employed to assess the probability distribution regarding the illumination factor. Meanwhile, an illumination perception loss is formulated by the illumination probabilities to enable the proposed MAIANet to better adjust to the changes in illumination. Experimental results on three datasets, that is, MSRS, TNO, and RoadSence, verify the effectiveness of the MAIANet in both qualitative and quantitative evaluations. [ABSTRACT FROM AUTHOR]

Image captioning (IC), bringing vision to language, has drawn extensive attention. A crucial aspect of IC is the accurate depiction of visual relations among image objects. Visual relations encompass two primary facets: content relations and structural relations. Content relations, which comprise geometric positions content (i.e., distances and sizes) and semantic interactions content (i.e., actions and possessives), unveil the mutual correlations between objects. In contrast, structural relations pertain to the topological connectivity of object regions. Existing Transformer-based methods typically resort to geometric positions to enhance the visual relations, yet only using the shallow geometric content is unable to precisely cover actional content correlations and structural connection relations. In this article, we adopt a comprehensive perspective to examine the correlations between objects, incorporating both content relations (i.e., geometric and semantic relations) and structural relations, with the aim of generating plausible captions. To achieve this, first, we construct a geometric graph from bounding box features and a semantic graph from the scene graph parser to model the content relations. Innovatively, we construct a topology graph that amalgamates the sparsity characteristics of the geometric and semantic graphs, enabling the representation of image structural relations. Second, we propose a novel unified approach to enrich image relation representations by integrating semantic, geometric, and structural relations into self-attention. Finally, in the language decoding stage, we further leverage the semantic relation as prior knowledge to generate accurate words. Extensive experiments on MS-COCO dataset demonstrate the effectiveness of our model, with improvements of CIDEr from 128.6% to 136.6%. Codes have been released at https://github.com/CrossmodalGroup/ER-SAN/tree/main/VG-Cap. [ABSTRACT FROM AUTHOR]

This article proposes a target image processing method based on super-resolution reconstruction and machine learning algorithms, which solves the low-resolution problem in medical images during imaging. This method uses nonlocal autoregressive learning based on a medical image super-resolution reconstruction method. The autoregressive model is introduced into the sparse representation-based medical image super-resolution reconstruction model by utilizing medical image data inherent nonlocal similarity characteristics. At the same time, a clustering algorithm is used to obtain a classification dictionary, improving experimental efficiency. The experimental results show that ten randomly selected CT/MR images are used as test images, and each image's peak signal-to-noise ratio and structural similarity values are calculated separately. Compared with other methods, the method proposed in this paper is significantly better and can achieve ideal results, with the highest value being 31.49. This method demonstrates the feasibility of using super-resolution reconstruction and machine learning algorithms in medical image resolution. [ABSTRACT FROM AUTHOR]

A new generation cone‐beam computed tomography (CBCT) system with new hardware design and advanced image reconstruction algorithms is available for radiation treatment simulation or adaptive radiotherapy (HyperSight CBCT imaging solution, Varian Medical Systems‐a Siemens Healthineers company). This study assesses the CBCT image quality metrics using the criteria routinely used for diagnostic CT scanner accreditation as a first step towards the future use of HyperSight CBCT images for treatment planning and target/organ delineations. Image performance was evaluated using American College of Radiology (ACR) Program accreditation phantom tests for diagnostic computed tomography systems (CTs) and compared HyperSight images with a standard treatment planning diagnostic CT scanner (Siemens SOMATOM Edge) and with existing CBCT systems (Varian TrueBeam version 2.7 and Varian Halcyon version 2.0). Image quality performance for all Varian HyperSight CBCT vendor‐provided imaging protocols were assessed using ACR head and body ring CT phantoms, then compared to existing imaging modalities. Image quality analysis metrics included contrast‐to‐noise (CNR), spatial resolution, Hounsfield number (HU) accuracy, image scaling, and uniformity. All image quality assessments were made following the recommendations and passing criteria provided by the ACR. The Varian HyperSight CBCT imaging system demonstrated excellent image quality, with the majority of vendor‐provided imaging protocols capable of passing all ACR CT accreditation standards. Nearly all (8/11) vendor‐provided protocols passed ACR criteria using the ACR head phantom, with the Abdomen Large, Pelvis Large, and H&N vendor‐provided protocols produced HU uniformity values slightly exceeding passing criteria but remained within the allowable minor deviation levels (5–7 HU maximum differences). Compared to other existing CT and CBCT imaging modalities, both HyperSight Head and Pelvis imaging protocols matched the performance of the SOMATOM CT scanner, and both the HyperSight and SOMATOM CT substantially surpassed the performance of the Halcyon 2.0 and TrueBeam version 2.7 systems. Varian HyperSight CBCT imaging system could pass almost all tests for all vendor‐provided protocols using ACR accreditation criteria, with image quality similar to those produced by diagnostic CT scanners and significantly better than existing linac‐based CBCT imaging systems. [ABSTRACT FROM AUTHOR]

In this paper, we explore the usage of boosted as well as semi-boosted topologies in all-hadronic t t ̄ final states in simulated p p collisions at s = 1 4 TeV, with top quarks decaying into a boosted hadronic top-jet or a W-jet and an isolated b-jet. Correlations between selected kinematic variables and their shapes are studied for scalar and vector resonances decaying to a pair of top quarks, and also for a models of t t ̄ -associated production with an invisible dark matter particle pair. Stacked signal + background samples have been investigated in terms of the ability to resolve an excess of events over the Standard Model background in terms of the t t ̄ invariant mass, top quark transverse momentum and other 1D and 2D spectra using a parameterized detector simulation. A 2D extension of the BumpHunter algorithm is proposed, resulting in an improved signal sensitivity in specific 2D areas. We identify the most promising variables with the largest signal significance and smaller sensitivity to experimental uncertainties related to the jet energy calibration. We compare to statistical tests computing the background-only hypothesis compatibility and a likelihood fit of the signal strength. [ABSTRACT FROM AUTHOR]

Objective. X-ray computed tomography employing sparse projection views has emerged as a contemporary technique to mitigate radiation dose. However, due to the inadequate number of projection views, an analytic reconstruction method utilizing filtered backprojection results in severe streaking artifacts. Recently, deep learning (DL) strategies employing image-domain networks have demonstrated remarkable performance in eliminating the streaking artifact caused by analytic reconstruction methods with sparse projection views. Nevertheless, it is difficult to clarify the theoretical justification for applying DL to sparse view computed tomography (CT) reconstruction, and it has been understood as restoration by removing image artifacts, not reconstruction. Approach. By leveraging the theory of deep convolutional framelets (DCF) and the hierarchical decomposition of measurement, this research reveals the constraints of conventional image and projection-domain DL methodologies, subsequently, the research proposes a novel dual-domain DL framework utilizing hierarchical decomposed measurements. Specifically, the research elucidates how the performance of the projection-domain network can be enhanced through a low-rank property of DCF and a bowtie support of hierarchical decomposed measurement in the Fourier domain. Main results. This study demonstrated performance improvement of the proposed framework based on the low-rank property, resulting in superior reconstruction performance compared to conventional analytic and DL methods. Significance. By providing a theoretically justified DL approach for sparse-view CT reconstruction, this study not only offers a superior alternative to existing methods but also opens new avenues for research in medical imaging. It highlights the potential of dual-domain DL frameworks to achieve high-quality reconstructions with lower radiation doses, thereby advancing the field towards safer and more efficient diagnostic techniques. The code is available at https://github.com/hanyoseob/HDD-DL-for-SVCT. [ABSTRACT FROM AUTHOR]

Objective. Computed Tomography (CT) has been widely used in industrial high-resolution non-destructive testing. However, it is difficult to obtain high-resolution images for large-scale objects due to their physical limitations. The objective is to develop an improved super-resolution technique that preserves small structures and details while efficiently capturing high-frequency information. Approach. The study proposes a new deep learning based method called spectrum learning (SPEAR) network for CT images super-resolution. This approach leverages both global information in the image domain and high-frequency information in the frequency domain. The SPEAR network is designed to reconstruct high-resolution images from low-resolution inputs by considering not only the main body of the images but also the small structures and other details. The symmetric property of the spectrum is exploited to reduce weight parameters in the frequency domain. Additionally, a spectrum loss is introduced to enforce the preservation of both high-frequency components and global information. Main results. The network is trained using pairs of low-resolution and high-resolution CT images, and it is fine-tuned using additional low-dose and normal-dose CT image pairs. The experimental results demonstrate that the proposed SPEAR network outperforms state-of-the-art networks in terms of image reconstruction quality. The approach successfully preserves high-frequency information and small structures, leading to better results compared to existing methods. The network's ability to generate high-resolution images from low-resolution inputs, even in cases of low-dose CT images, showcases its effectiveness in maintaining image quality. Significance. The proposed SPEAR network's ability to simultaneously capture global information and high-frequency details addresses the limitations of existing methods, resulting in more accurate and informative image reconstructions. This advancement can have substantial implications for various industries and medical diagnoses relying on accurate imaging. [ABSTRACT FROM AUTHOR]

Vector Quantization (VQ) is a technique with a wide range of applications. For example, it can be used for image compression. The codebook design for VQ has great significance in the quality of the quantized signals and can benefit from the use of swarm intelligence. Initialization of the Linde–Buzo–Gray (LBG) algorithm, which is the most popular VQ codebook design algorithm, is a step that directly influences VQ performance, as the convergence speed and codebook quality depend on the initial codebook. A widely used initialization alternative is random initialization, in which the initial set of codevectors is drawn randomly from the training set. Other initialization methods can lead to a better quality of the designed codebooks. The present work evaluates the impacts of initialization strategies on swarm intelligence algorithms for codebook design in terms of the quality of the designed codebooks, assessed by the quality of the reconstructed images, and in terms of the convergence speed, evaluated by the number of iterations. Initialization strategies consist of a combination of codebooks obtained by initialization algorithms from the literature with codebooks composed of vectors randomly selected from the training set. The possibility of combining different initialization techniques provides new perspectives in the search for the quality of the VQ codebooks. Nine initialization strategies are presented, which are compared with random initialization. Initialization strategies are evaluated on the following algorithms for codebook design based on swarm clustering: modified firefly algorithm—Linde–Buzo–Gray (M-FA-LBG), modified particle swarm optimization—Linde–Buzo–Gray (M-PSO-LBG), modified fish school search—Linde–Buzo–Gray (M-FSS-LBG) and their accelerated versions (M-FA-LBGa, M-PSO-LBGa and M-FSS-LBGa) which are obtained by replacing the LBG with the accelerated LBG algorithm. The simulation results point out to the benefits of the proposed initialization strategies. The results show gains up to 4.43 dB in terms of PSNR for image Clock with M-PSO-LBG codebooks of size 512 and codebook design time savings up to 67.05% for image Clock, with M-FF-LBGa codebooks with size N = 512 , by using initialization strategies in substitution to Random initialization. [ABSTRACT FROM AUTHOR]

Due to the excellent characteristics of Synthetic Aperture Radar (SAR), it has become an important technical means for land and sea target detection applications worldwide. However, the SAR image imaging process is often accompanied by speckle noise, which affects the accuracy of target detection. For this problem, this paper proposes an SAR image reconstruction model based on image denoising and feature extraction. Given a noisy SAR image, at each pixel of the image, the value of the singularity index of a metric defined by the signal gradient norm density is calculated. Then through a hierarchical decomposition of these singular indices, a set of pixels containing the most informative feature set of the image is extracted, and a denoised image is reconstructed using the extracted features. In comparison to traditional filtering and denoising techniques such as non-local filtering, this algorithm achieves remarkable local filtering and denoising effects while preserving the image's texture information. The denoising performance of the proposed method is evaluated through a series of quantitative indicators and visual comparisons. The results demonstrate that this method effectively reduces background clutter, resulting in a higher contrast between the target and the background. [ABSTRACT FROM AUTHOR]