Search

P3HT:PCBM blends applied as active layers for bulk heterojunction organic solar cells generally show unstable morphologies upon prolonged thermal annealing, severely limiting the lifetime of the devices. As such, the thermodynamic instability of the blend is a limiting factor in the overall performance of organic photovoltaics, and a strong disadvantage in the fierce competition with other photovoltaic technologies. This paper shows whether different blend preparation conditions and intrinsic structural changes in the side chains of poly(3-alkylthiophene) (P3AT) derivatives can influence the thermal stability of the resulting solar cells. A combination of Bright Field Transmission Electron Microscopy (BFTEM) and the analysis of Selected Area Electron Diffraction (SAED) patterns revealed that the investigated preparation conditions do not really affect the thermal stability, whereas the introduction of a small ratio (10%) of specific functional moieties in the side chains of random P3AT copolymers does improve the thermal stability significantly. It was demonstrated that demixing of the blend components upon prolonged thermal annealing is strongly delayed in the functionalized P3AT:PCBM blends. The enhanced thermal stability was confirmed by in-situ monitoring of the short circuit current of organic solar cells based on the respective active layers. The introduction of functionalized side chains hence represents an attractive approach to increase the operational stability of organic photovoltaics based on the bulk heterojunction concept.

We report on the synthesis of new thermally cross-linkable all-conjugated diblock copolymers composed of a poly(3-hexylthiophene) (P3HT) block and an acrylate-functionalized polythiophene block. These copolymers are then used in bulk heterojunction (BHJ) solar cells with [6,6]-phenyl C61-butyric acid methyl ester (PCBM), and their photovoltaic performances are compared with standard P3HT/PCBM devices. Thermal cross-linking of the functional copolymers/PCBM blends is performed to improve the thermal stability of the active layer. BHJ photovoltaic cells with cross-linkable copolymers and PCBM show initial power conversion efficiencies slightly lower than that of P3HT devices. However, solar cells with cross-linkable copolymers retain more than 85% of their initial power efficiency value after 165 h of thermal annealing (accelerated aging test), whereas the same devices with P3HT retain less than 65% of their initial power efficiency. This improvement of the thermal stability of BHJ photovoltaic cells is the...

Organic solar cells (OSC) are green solar energy technology, which can be fabricated from organic compounds with cheep techniques and on flexible or transparent substrates such as plastic or glass. OSCs are cost efficient, and lightweight devices that can exhibit high power conversion efficiency (PCE) under low light irradiation. These advantages have made OSCs of great interest, and they have been extensively studied over the course of past few years1. Despite these advantages, OSCs have low stability and lifetime, which puts a barrier between laboratory achievements and industrial scale requirements. Therefore, in order to closing this gap and to obtain further improvements in the device performance and long-term outdoor stabilities, a detailed understanding of the device degradation mechanism is required. In an OSC, effective dissociation of the excitons takes place at the donor-acceptor interface via delocalized charge-transfer (CT) states, which represents an intermediate state between the exciton dissociation and recombination back to the ground state. In this work we perform the electroluminescence (EL) created by bimolecular free career recombination and sensitive external quantum efficiency measurements (sEQE) in DBP:C70 based SCs as a less studied system in order to study the energy and effect of CT states on degradation of the devices2. The results from these measurements reveal valuable information about the loss mechanism during the aging experiment as well as the energy of the CT states from which the maximum open circuit can be calculated and will set the base for modeling and optimizing the stability of the solar cells. 1. Cao, H. et al. Recent progress in degradation and stabilization of organic solar cells. J. Power Sources 264, 168–183 (2014).2. Tvingstedt, K. et al. Electroluminescence from charge transfer states in polymer solar cells. J. Am. Chem. Soc. 131, 11819–11824 (2009).

The non-geminate recombination of charge carriers in polymer-fullerene solar cells has been modeled in the last few years with a trap-assisted recombination model, which states that the apparent recombination order depends on the concentration of trapped charges tailing into the band gap. Higher concentrations of trapped charges lead to higher apparent recombination orders. In this work, the mass fraction f of highly crystalline nanofibrillar P3HT to the total P3HT content in P3HT:PCBM solar cells is consistently varied, controlling the temperature of a nanofibers-P3HT casting dispersion. A systematic study of the apparent recombination order, measured with a transient photovoltage technique, as a function of f is presented. A correlation is shown between the apparent recombination order, the P3HT crystallinity, and the trap concentration in the band gap measured with an admittance spectroscopy technique

This paper focuses on the characterization of the ZnO/poly(3- hexylthiophene) (P3HT) interfaces in nanostructured hybrid solar cells, aiming to elucidate the relationship between thermal treatment, local morphology, and device performance. An equivalent impedimetric model for the device is proposed, allowing us to extract information about the ZnO/P3HT interface morphology and its impact on the photovoltaic properties by comparing devices with and without nanopatterning. It is found that the influence of thermal treatment on performance lies solely in the interface, resulting from a different interfacial morphology of P3HT depending on which crystal direction of ZnO is present. © 2011 American Chemical Society. ispartof: Journal of Physical Chemistry C vol:115 issue:33 pages:16695-16700 status: published

The use of nanostructured non-conventional semiconductors such as conjugated polymers and metal oxides (e.g. TiO2), opens promising perspectives towards a new generation of solar cells based on the concept of donor:acceptor bulk heterojunctions. In this concept donor material and acceptor material form interpenetrating networks allowing light absorption, charge transfer and charge transport throughout the entire bulk of the thin film. Since nanomorphology is of crucial importance for this type of solar cells, in this contribution the use of nanofibers in bulk heterojunction solar cells is explored in order to obtain highways for charge transport. We investigate in particular the use of P3AT (poly(3-alkylthiophene)) nanofibers and show that the polymer fraction aggregated into fibers can be easily controlled by temperature. We find an optimal efficiency at intermediate fiber fraction and show that it can be linked to the morphology of the active layer.

To improve the thermal stability of polymer:fullerene bulk heterojunction solar cells, a new polymer, poly[2-methoxy-5-(2'-phenylethoxy)-1,4-phenylenevinylene] (MPE-PPV), has been designed and synthesized, which showed an increased glass transition temperature (Tg) of 111 °C. The thermal characteristics and phase behavior of MPE-PPV:[6,6]-phenyl C61-butyric acid methyl ester ([60]PCBM) blends were investigated by means of modulated temperature differential scanning calorimetry and rapid heating–cooling calorimetry. The thermal stability of MPE-PPV:[60]PCBM solar cells was compared with devices based on the reference MDMO-PPV material with a Tg of 45 °C. Monitoring of the photocurrent–voltage characteristics at elevated temperatures revealed that the use of high-Tg MPE-PPV resulted in a substantial improvement of the thermal stability of the solar cells. Furthermore, a systematic transmission electron microscope study of the active polymer:fullerene layer at elevated temperatures likewise demonstrated a more stable morphology for the MPE-PPV:[60]PCBM blend. Both observations indicate that the use of high-Tg MPE-PPV as donor material leads to a reduced free movement of the fullerene molecules within the active layer of the photovoltaic device. Finally, optimization of the PPV:fullerene solar cells revealed that for both types of devices the use of [6,6]-phenyl C71-butyric acid methyl ester ([70]PCBM) resulted in a substantial increase of current density and power conversion efficiency, up to 3.0% for MDMO-PPV:[70]PCBM and 2.3% for MPE-PPV:[70]PCBM.

Although platinum (Pt) is a rare and very expensive material, Pt counter electrodes are still very commonly used for reaching high efficiencies in dye-sensitized solar cells (DSCs). The use of alternative cheaper catalyst materials did not yet yield equivalent efficiencies. In this work, we tried to understand how to reduce the amount of deposited Pt-material and simultaneously deliver higher DSC performances. We systematically compared the properties of Pt-counter electrodes prepared by simple solution deposition methods such as spray-coating, dip-coating, brushing with reference to the Pt-electrodes prepared by sputtering onto fluorine doped-tin oxides (FTOs). The morphological and structural characterizations of the deposited Pt-layers were performed by atomic force microscopy (AFM) and scanning electron microscopy (SEM). The composition of Pt-material was quantified using SEM electron dispersive X-ray (EDX) mapping measurements which were further compared with optical transmission measurements. Also contact angle and sheet resistance measurements were performed. By taking Pt-layers composition, morphology and structural factors into account, 9.16% efficient N3 dye based DSCs were assembled. The DSCs were subjected to various opto-electrical characterization techniques like current–voltage (I–V), external quantum efficiency (EQE), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and transient photo voltage (TPV) measurements. The obtained experimental data suggest that the Pt counter electrodes prepared by solution deposition methods can also reach high DSC device performances with a consumption of very little amount of Pt material as compared with sputtered Pt-layers. This process also proves that higher DSC performances are not limited to the usage of sputtered Pt-layer as counter electrode.

Graphene has potential for applications in solar cells. We show that the short circuit current density of P3HT (Poly(3-hexylthiophene-2,5-diyl):PCBM((6,6)-Phenyl C61 butyric acid methyl ester) solar cells is enhanced by 10% upon the addition of graphene, with a 15% increase in the photon to electric conversion efficiency. We discuss the performance enhancement by studying the crystallization of P3HT, as well as the electrical transport properties. We show that graphene improves the balance between electron and hole mobilities with respect to a standard P3HT:PCBM solar cell.

Lately, research efforts in photovoltaics towards hybrid solar cells based on nanostructured metal oxides and conjugated polymers have been intensifying. However, very limited effort has been spent so far to investigate their recombination kinetics in comparison with their fully organic counterpart. In this work, impedance spectroscopy under different illumination intensities is used to probe the recombination kinetics of hybrid solar cells based on ZnO nanorod arrays and poly(3-hexylthiophene). A recombination-based model developed for fully organic solar cells is effectively applied in our hybrid solar cells, demonstrating their similarity in device physics and establishing the nanorod array/polymer compound as true bulk heterojunction.

Metal-substituted phthalocyanine thin films such as copper-phthalocyanine (CuPc) are often used as photo-active and hole transporting layers (HTLs) in fully organic photovoltaic devices. In this work, CuPc is vacuum sublimated on an electron acceptor layer of mesoporous titania (TiO(2)) for the formation of hybrid TiO(2):CuPc solar cell devices. The performance of these hybrid solar cell devices was demonstrated without and with dye sensitization at the TiO(2):CuPc interface. The charge separation and photocurrent contribution at the interfaces in these multilayer hybrid devices was studied by using a variety of optoelectrical and photophysical characterization techniques. It is important to understand the fundamental interface properties of these multilayer hybrid solar cell devices for optimized performance.

Electrical transport properties of poly (3-hexylthiophene) (P3HT) (6,6)-phenyl C61-butyric acid methyl ester (PCBM) solar cells, with and without encapsulation, have been investigated and analyzed using admittance spectroscopy and capacitance voltage measurements at different temperatures. The admittance spectroscopy clearly reveals two defect states with activation energies of 53 and 100 meV, and a concentration ten times higher in the unencapsulated sample. These defects seem to have a strong effect on the charge transport and the solar cell performance when they are present with a high concentration, since they lead to a decrease of the mobility and also the short-circuit current and the efficiency. The origin of these defects has been assigned to reaction of the blend with O2 which is also known to induce p-type doping in pure P3HT. In an attempt to understand the effect of these defects on the organic solar cell performance, modeling and simulation were carried out using the effective medium layer model and gave good agreement with the measurements results.

Stability is now a critical factor in the commercialization of organic photovoltaic (OPV) devices. Both extrinsic stability to oxygen and water and intrinsic stability to light and heat in inert conditions must be achieved. Triplet states are known to be problematic in both cases, leading to singlet oxygen production or fullerene dimerization. The latter is thought to proceed from unquenched singlet excitons that have undergone intersystem crossing (ISC). Instead, we show that in bulk heterojunction (BHJ) solar cells the photo-degradation of C60 via photo-oligomerization occurs primarily via back-hole transfer (BHT) from a charge-transfer state to a C60 excited triplet state. We demonstrate this to be the principal pathway from a combination of steady-state optoelectronic measurements, time-resolved electron paramagnetic resonance, and temperature-dependent transient absorption spectroscopy on model systems. BHT is a much more serious concern than ISC because it cannot be mitigated by improved exciton quenching, obtained for example by a finer BHJ morphology. As BHT is not specific to fullerenes, our results suggest that the role of electron and hole back transfer in the degradation of BHJs should also be carefully considered when designing stable OPV devices., The commercialisation of organic photovoltaic technology calls for research on material degradation mechanisms. Ramirez et al. show that triplet excitons produced by back charge transfer can significantly impact the photo-stability of fullerene-based devices even in the absence of water and oxygen.

The molecular weight of poly(3-hexylthiophene) is an important factor influencing the photovoltaic properties of bulk heterojunction organic solar cells based on this material. However, since different synthetic processes or repetitive soxhlet extractions - generally applied to obtain the different molecular weight batches under study - result in samples with simultaneously varying regioregularity (RR) and polydispersity index (PDI), it has not been possible yet to find an unambiguous correlation between the molecular weight and the photovoltaic performance. In the present work preparative gel permeation chromatography is introduced as a versatile technique to fractionate the donor polymer and thereby obtain a systematic variation of the number average molecular weight (M-n = 11-91 kg mol (1)) with an almost constant PDI and RR. Polymer crystallinity and conjugation length are evaluated by UV-Vis spectroscopy, rapid heat-cool calorimetry and selected area electron diffraction, and are found to be deeply affected by Mn. This in turn influences the behavior of the charge transfer state energy, measured via Fourier transform photocurrent spectroscopy, and therefore the open-circuit voltage. The short-circuit current is also affected by Mn, but mainly due to a change in absorption coefficient. The apparent recombination order is shown to be linked to the morphology of the polymer: fullerene blend and is determined using transient photovoltage and photocurrent techniques. Finally, a correlation between recombination and fill factor is also suggested.

The best organic solar cells (OSCs) achieve comparable peak external quantum efficiencies and fill factors as conventional photovoltaic devices. However, their voltage losses are much higher, in particular those due to nonradiative recombination. To investigate the possible role of triplet states on the donor or acceptor materials in this process, model systems comprising Zn- and Cu-phthalocyanine (Pc), as well as fluorinated versions of these donors, combined with C-60 as acceptor are studied. Fluorination allows tuning the energy level alignment between the lowest energy triplet state (T-1) and the charge-transfer (CT) state, while the replacement of Zn by Cu as the central metal in the Pcs leads to a largely enhanced spin-orbit coupling. Only in the latter case, a substantial influence of the triplet state on the nonradiative voltage losses is observed. In contrast, it is found that for a large series of typical OSC materials, the relative energy level alignment between T-1 and the CT state does not substantially affect nonradiative voltage losses. This work was supported by the German Federal Ministry for Education and Research (BMBF) through the InnoProfile project "Organische p-i-n Bauelemente 2.2" and the European Union's Horizon 2020 research and innovation programme under Marie Sklodowska Curie Grant agreement No. 722651 (SEPOMO). F.P. and D.N. acknowledge funding by the German Research Foundation (DFG) via the SFB 951 "HIOS". The authors acknowledge Prof. K. Leo and V. C. Nikolis for fruitful discussions. The authors thank Dr. B. Beyer for supplying ZnF4Pc and CuF4Pc as well as Dr. M. Lau for the synthesis of F4CuPc. Additionally, the authors thank Prof. Bauerle from University of Ulm for the supply of DH4T, DH6T, and several DCV2-nT-R. Furthermore, the authors acknowledge Dr. F. Holzmueller, M. Saalfrank, and Dr. R. Meerheim for providing OSC devices for this study. Computational resources were provided by the Consortium des Equipements de Calcul Intensif (CECI), funded by the Fonds de la Recherche Scientifiques de Belgique (F.R.S.-FNRS) under Grant No. 2.5020.11, as well as the Tier-1 supercomputer of the Federation Wallonie-Bruxelles, infrastructure funded by the Walloon Region under Grant Agreement No. 1117545. D.B. is a FNRS Research Director.