Search

This study explores the efficiency and kinetics of the photoactivated periodate process for the degradation of 2,4-dichlorophenol (2,4-DCP) in water. The obtained results show that the degradation rate was considerably higher for UV/IO4- compared to UV irradiation alone. Pseudo first-order reaction rate kinetics were obtained for all process conditions. The pH did not have a significant impact on the decomposition of 2,4-DCP using photoactivated periodate. Therefore, the applied method can be used to treat (waste)water at various pH. By raising the initial concentration of periodate to 5 mM, the degradation rate increased, while it decreased again at a concentration of 8 mM. As the 2,4-DCP concentration increased, the removal rate decreased. The extent of degradation was observed to be proportional with the UV intensity. A mechanistic study revealed that iodine radicals dominated the degradation of 2,4-DCP by photoactivated periodate, whereas OH and O(3P) only played a minor role. At pH 5.0, all chlorine atoms in 2,4-DCP were released as chloride ions in the UV/IO4- process, hence reaching a total dechlorination. Finally, the presence of inorganic salts, even at high levels, did not significantly impact the degradation. According to the results achieved in this study, the UV/IO4- system can be considered as a valuable alternative to treat effluents containing chlorinated organic compounds such as pulp and paper mill effluents and brine (waste)water.

An analytical procedure to measure the whole-body uptake of pharmaceuticals in zebrafish has been developed using state-of-the-art methodologies. A sample preparation procedure for 9 pharmaceuticals displaying a variety in physicochemical properties was developed using 10-day old zebrafish (TG898). For an efficient homogenization of the samples and subsequent recovery of the compounds of interest, different amounts of organic solvents in combination with acidic modifiers were added to zebrafish samples. Samples were subsequently processed using a powerful bath sonicator and centrifuged. Supernatant was then removed and evaporated in a vacuum oven before being reconstituted in a mobile phase-like solvent. Samples were analyzed using ultra-high performance liquid chromatography (UHPLC) on an Acquity BEH C18 column (100 × 2.1mm, dp=1.7µm) coupled to a Waters Xevo TQ-S mass spectrometer. For this purpose, a generic gradient was run, wherein the percentage of acetonitrile was varied from 3% to 82% in 10.5min at a flow rate of 0.41mL/min. Linearity of the method was demonstrated for all compounds (R2 > 0.997) in a practically relevant concentration range. Matrix effects were between 81% and 106%, except for amitriptyline (51%). Using this method, it was demonstrated that a sample pretreatment using 1:2 (v/v) water:methanol in combination with 0.1% formic acid resulted in acceptable recoveries between 74% and 100% for all compounds. Together with the obtained lower limits of quantification of the analytical method (between 0.005 and 1.5ng/mL), this allowed the use of a single zebrafish to study the whole-body uptake of a particular drug, after incubating zebrafish at the maximum tolerated concentration for this drug.

A recently developed stripping protocol to completely remove the stationary phase of reversed-phase liquid chromatography (RPLC) columns and turn them into hydrophilic interaction liquid chromatography (HILIC) columns with identical packing characteristics is used to study the underlying mechanisms of intra-particle diffusion in RPLC and HILIC. The protocol is applied to a column with a large geometrical volume (250 x 4.6 mm, 5 mu m) to avoid extra-column effects and for compounds with a broad range in retention factors (k" from similar to 0.6 to 8). Three types of behavior for the intra-particle diffusion (D-part/D-m) in RPLC versus HILIC can be distinguished: for nearly unretained compounds (k" < 0.6), intra-particle diffusion in HILIC is larger than in RPLC; for compounds with intermediate retention behavior (k" similar to 0.9-1.2), intra-particle diffusion in HILIC and RPLC are similar; and for well retained compounds (k" > 1.8), intraparticle diffusion in RPLC is larger than in HILIC. To explain these observations, diffusion in the stationary phase (gamma D-s(s)) and in the stagnant mobile phase in the mesopore zone (gamma D-mp(m)) are deduced from experimentally determined values of the intra-particle diffusion, using models derived from the Effective Medium Theory. It is demonstrated that the larger intra-particle diffusion obtained for slightly retained compounds under HILIC conditions is caused by the higher mesopore diffusion in HILIC (gamma(mp) = 0.474 for HILIC versus 0.435 for RPLC), while the larger intra-particle diffusion obtained for strongly retained compounds, under RPLC conditions can be related to the much higher stationary phase diffusion in RPLC (gamma D-s(s)/D-m = 0.200 for RPLC versus 0.113 for HILIC). (C) 2017 Elsevier B.V. All rights reserved.

Lack of knowledge on the expected concentration range or insufficient linear dynamic range of the analytical method applied are common challenges for the analytical scientist. Samples that are above the upper limit of quantification are typically diluted and reanalyzed. The analysis of undiluted highly concentrated samples can cause contamination of the system, while the dilution step is time consuming and as the case for any sample preparation step, also potentially leads to precipitation, adsorption or degradation of the analytes. ispartof: Journal of Chromatography A vol:1524 pages:101-107 ispartof: location:Netherlands status: published

A fast methodology to quantify 4-tert-octylphenol (4-t-OP) and 4-nonylphenol (4-NP) and their mono- and di-ethoxylates was developed, validated, and applied to real wastewater samples. Dispersive liquid-liquid microextraction was employed as a sample preparation step, leading to a pre-concentration factor of roughly 30. Analysis was carried out by liquid chromatography-tandem mass spectrometry with electrospray ionisation in multiple reaction monitoring mode. Average recoveries were generally between 80 and 120% for both the alkylphenols and their mono- and di-ethoxylates in influent and effluent wastewater. A minimum of 5 concentration levels per compound, ranging between 1 and 500 ng/mL, were prepared to construct calibration curves making use of isotopically labelled internal standards. The method presented good linearity and repeatability over the whole range of concentrations. Taking into account the concentration factor, and the recovery of the compounds, lower limits of quantification obtained in effluent wastewater were 0.04 ng/mL for 4-t-OP and 0.14 ng/mL for 4-NP, complying with European regulations, and between 0.03 ng/mL and 0.39 ng/mL for the ethoxylates. In influent wastewater, these limits were slightly higher. The total run time of 5 min for the alkylphenols and 8 min for the ethoxylates ensured high throughput. The developed method was applied to determine 4-t-OP and 4-NP and their mono- and di-ethoxylates in wastewater from several tank truck cleaning companies, which was subjected to ozonation and/or biological treatment. It was demonstrated that ozonation was best applied after the biological treatment, since in this case, the biological treatment could degrade most of the biodegradable organic matter, after which ozone could react directly with the recalcitrant organic pollutants. In this case, the concentrations of the target compounds in the wastewater of the investigated company decreased below the legally allowed concentration of the European water legislation. ispartof: ANALYTICAL AND BIOANALYTICAL CHEMISTRY vol:411 issue:8 pages:1611-1621 ispartof: location:Germany status: published

© 2018, Springer-Verlag GmbH Germany, part of Springer Nature. The occurrence of phenazone-type analgesics, such as aminopyrine, metamizole, phenazone and propyphenazone, has been reported in the effluent of wastewater treatment plants in µg/L concentrations. The presence of the main metabolites of aminopyrine and metamizole—acetamido antipyrine and formyl aminoantipyrine—has even been detected in sub µg/L concentrations in surface water and water bodies used to produce drinking water. This points at their high persistence and the need for adequate removal strategies. The degradation of phenazone, propyphenazone, acetamido antipyrine and formyl aminoantipyrine by UV radiation was investigated under laboratory conditions. An elucidation approach based on high-resolution mass spectrometry resulted in the identification of 11 degradation products. A mechanism of ring opening via the oxidation of the N–N bond of the pyrazolone ring was observed as well as the more typical oxidation of carbon–carbon double bonds. Aside from the degradation products, the capacity of formyl aminoantipyrine to produce trimers and dimers was demonstrated. The dimers were shown to be persistent despite continuous UV radiation. The toxicity of the degradation products was assessed by quantitative structure–activity relationships. It was shown that when the carbon–carbon double bond is partially oxidized to an epoxy the toxicity towards fish and daphnid is increased with respect to the parent compound. ispartof: CHROMATOGRAPHIA vol:82 issue:1 pages:261-269 status: published

For a successful reclamation of aquatic systems, advanced reduction processes (ARP) have recently attracted a lot of attention for the elimination of emerging pharmaceutical compounds. This study investigates the synergistic effect between UV and sulfite (UV/sulfite) for the degradation of carbamazepine (CBZ) and elucidates the critical process parameters and degradation mechanisms. No efficient degradation of CBZ is observed when applying sulfite alone, and only little degradation for UV irradiation alone (8.2% in 30 min reaction time), but the combined use of UV/sulfite ARP improves CBZ degradation significantly (99.62% in the same reaction time) through the formation of reductive radicals (eaq−, H , SO3 −). The process is demonstrated to follow a pseudo first order kinetic model, with degradation rate constants of CBZ increasing linearly with increasing sulfite dosage and UV irradiance. It is shown that the degradation of CBZ by UV/sulfite is much more favourable in alkaline conditions than in acidic conditions due to the more favourable distribution between SO32− and HSO3−, which are the precursors of the radicals generated during the UV/sulfite process. It is demonstrated that hydrated radicals (eaq−) are responsible for CBZ degradation, excluding the function of hydrogen atoms (H ) and sulfite radicals (SO3 −). Inhibition experiments, conducted by introducing radical scavengers (NO3− and NO2−) into the system, further demonstrate the crucial contribution of eaq− on the degradation of CBZ. The energy consumption is evaluated for different UV intensities and sulfite concentrations and indicates that a dose of 0.4 mM sulfite in combination with a 18 W UV lamp is the most economic. This study emphasizes the dominant impact of eaq− on CBZ degradation in UV/sulfite-ARP systems and highlights the potential of this process to efficiently eliminate recalcitrant micropollutants in aquatic environments.

Columns packed with new commercially available 1.9 fully porous particles of narrow particle size distribution (nPSD) are characterized by extremely high efficiency. Under typical reversed phase conditions, these columns are able to generate very high number of theoretical plates (in the order of 300,000 plates/m and more). In this paper, we investigate the origin of the high performance of these nPSD columns by performing a series of measurements that include, in addition to the traditional determination of the van Deemter curve, peak parking, pore blocking and inverse size exclusion experiments. Two nPSD columns (both 100 x 3.0 mm) have been considered in this study: the first one, packed with particles of 80 angstrom pore size, is commercially available. The second one is a prototype column packed with 1.9 fully porous particles of 120 angstrom pore size. The main conclusion of our study is that these nPSD columns are characterized by extremely low eddy dispersion, while longitudinal diffusion and mass transfer kinetics are substantially equivalent to those of other fully porous particles of similar chemistry. (C) 2016 Elsevier B.V. All rights reserved.

Eicosanoids, including prostaglandins and thromboxanes are lipid mediators synthetized from polyunsaturated fatty acids. They play an important role in cell signaling and are often reported as inflammatory markers. LC-MS/MS is the technique of choice for the analysis of these compounds, often in combination with advanced sample preparation techniques. Here we report a head to head comparison between an electrospray ionization source (ESI) and a new atmospheric pressure ionization source (UniSpray). The performance of both interfaces was evaluated in various matrices such as human plasma, pig colon and mouse colon. The UniSpray source shows an increase in method sensitivity up to a factor 5. Equivalent to better linearity and repeatability on various matrices as well as an increase in signal intensity were observed in comparison to ESI. publisher: Elsevier articletitle: Enhanced performance for the analysis of prostaglandins and thromboxanes by liquid chromatography-tandem mass spectrometry using a new atmospheric pressure ionization source journaltitle: Journal of Chromatography A articlelink: http://dx.doi.org/10.1016/j.chroma.2016.02.055 content_type: article copyright: Copyright © 2016 Elsevier B.V. All rights reserved. ispartof: Journal of Chromatography A vol:1440 pages:260-5 ispartof: location:Netherlands status: published

We report on a systematic and comprehensive (0.7

Amyotrophic Lateral Sclerosis (ALS) is a fatal degenerative motor neuron disorder of which the progression is influenced by several disease-modifying factors. Here, we investigated ELP3, a subunit of the elongator complex that modifies tRNA wobble uridines, as one of such ALS disease modifiers. ELP3 attenuated the axonopathy of a mutant SOD1, as well as of a mutant C9orf72 ALS zebrafish model. Furthermore, expression of ELP3 in the SOD1G93A mouse extended the survival and attenuated the denervation in this model. Depletion of ELP3 in vitro reduced the modified tRNA wobble uridine mcm5s2U and increased abundance of insoluble mutant SOD1, which was reverted by exogenous ELP3 expression. Interestingly, the expression of ELP3 in the motor cortex of ALS patients was reduced and correlated with mcm5s2U levels. Our results demonstrate that ELP3 is a modifier of ALS and suggest a link between tRNA modification and neurodegeneration. ispartof: Human Molecular Genetics vol:27 issue:7 pages:1276-1289 ispartof: location:England status: published

This study aims at investigating the efficiency and kinetics of 2,4-DCP degradation via advanced reduction processes (ARP). Using UV light as activation method, the highest degradation efficiency of 2,4-DCP was obtained when using sulphite as a reducing agent. The highest degradation efficiency was observed under alkaline conditions (pH = 10.0), for high sulphite dosage and UV intensity, and low 2,4-DCP concentration. For all process conditions, first-order reaction rate kinetics were applicable. A quadratic polynomial equation fitted by a Box-Behnken Design was used as a statistical model and proved to be precise and reliable in describing the significance of the different process variables. The analysis of variance demonstrated that the experimental results were in good agreement with the predicted model (R2 = 0.9343), and solution pH, sulphite dose and UV intensity were found to be key process variables in the sulphite/UV ARP. Consequently, the present study provides a promising approach for the efficient degradation of 2,4-DCP with fast degradation kinetics. ispartof: JOURNAL OF HAZARDOUS MATERIALS vol:357 pages:81-88 ispartof: location:Netherlands status: published

A stability-indicating method for the determination of S-carboxymethyl-L-cysteine and related degradation impurities in Exputex® 250mg/5mL syrup was developed in anion-exchange liquid chromatography mode. A forced degradation study supported the method development to ensure stability indicating conditions. Aqueous solutions of the active pharmaceutical ingredient and syrup samples at different pH-values were stress-tested in different thermal, light exposure and headspace conditions. One degradation product was detected in thermal stress studies at 60°C and 80°C in the pH range 5.0-7.0 and was identified by mass spectrometry as 5-oxo-thiomorpholine-3-carboxylic acid (lactam of carbocysteine). A second degradation product was only generated in moderately strong oxidizing conditions (0.5% H2O2 aqueous solution) and was identified as S-carboxymethyl-L-cysteine-(R/S)-sulphoxide (carbocysteine sulphoxide). The method was developed on a Zorbax SAX column, in isocratic mode. The mobile phase consisted of 200mM phosphate solution at pH 4.0 and acetonitrile (50:50 v/v) and UV detection was performed at a wavelength of 205nm. The method was linear for carbocysteine (R>0.9982) over a concentration range of 2.5-50μg/mL and 0.4-0.6mg/mL. Linearity for the impurities was shown from the LOQ to 50μg/mL. Specificity was verified and accuracy demonstrated for the active ingredient and its degradation products in syrup samples at 3 levels around their respective specification limits. Repeatability, intermediate precision and inter-laboratory reproducibility were assessed on three commercial batches, analyzed in triplicate by two operators at both the transferring and the receiving site and demonstrated a successful method transfer to the manufacturing quality control laboratory.

Phenazone-type pharmaceuticals, such as aminopyrine, metamizole, phenazone and propyphenazone, are widely used analgesics that have been detected in wastewater treatment plant effluents in μg L−1 concentrations. Acetamido antipyrine (AAA) and formyl aminoantipyrine (FAA) – the main metabolites of aminopyrine and metamizole – have also been detected in sub μg L−1 concentrations in environmental water bodies and in resources used to produce drinking water, suggesting their highly persistent character. In this study phenazone, propyphenazone, AAA and FAA were treated with ozone under laboratory conditions and 17 degradation products were identified by an elucidation approach based on high-resolution mass spectrometry (LTQ Orbitrap). Typical oxidation of carbon–carbon double bonds by ozone was observed among other mechanisms of ring opening. It was demonstrated that reactivity of these compounds with ozone is high (rate constants kO3 ranging from 6.5 × 104 to 2.4 × 106 M−1 s−1). The toxicity of the degradation products from ozonation was estimated by quantitative structure–activity relationships (QSAR). It was shown that, when the carbon–carbon double bond is partially oxidized to an epoxy, the toxicity towards fish and daphnids is higher than that of the parent compound. By further oxidizing the molecules, a common degradation product – 1-acetyl-1-methyl-2-phenylhydrazide (AMPH) – was also found to be more toxic than its parent compounds, which is of concern since this compound has previously been reported in environmental waters.

Structural elucidation of metabolites is an important part during the discovery and development process of new pharmaceutical drugs. Liquid Chromatography (LC) in combination with Mass Spectrometry (MS) is usually the technique of choice for structural identification but cannot always provide precise structural identification of the studied metabolite (e.g. site of hydroxylation and site of glucuronidation). In order to identify those metabolites, different approaches are used combined with MS data including nuclear magnetic resonance, hydrogen/deuterium exchange and chemical derivatization followed by LC-MS. Those techniques are often time-consuming and/or require extra sample pre-treatment. In this paper, a fast and easy to set up tool using desorption electrospray ionization-MS for metabolite identification is presented. In the developed method, analytes in solution are simply dried on a glass plate with printed Teflon spots and then a single drop of derivatization mixture is added. Once the spot is dried, the derivatized compound is analyzed. Six classic chemical derivatizations were adjusted to work as a one drop reaction and applied on a list of compounds with relevant functional groups. Subsequently, two successive reactions on a single spot of amoxicillin were tested and the methodology described was successfully applied on an in vitro incubated alprazolam metabolite. All reactions and analyses were performed within an hour and gave useful structural information by derivatizing functional groups, making the method a time-saving and efficient tool for metabolite identification if used in addition or in some cases as an alternative to common methods.

International audience

The type and design of an ionization source can have a significant influence on the performances of a bioanalytical method. It is, therefore, of high interest to evaluate the performances of newly introduced sources to highlight their benefits and limitations in comparison to other well established sources. In this paper, liquid chromatography - mass spectrometry (LC/MS) performances of a new atmospheric pressure ionization (API) source, commercialized as UniSpray, is evaluated. The dynamic range of 24 pharmaceutical and biological compounds is compared between the new API source and electrospray ionization (ESI) for 3 different mobile phase conditions. Matrix effects are also compared with ESI on a refined selection of 19 pharmaceutical and biological compounds in 4 matrices commonly encountered in bioanalysis. A slightly better dynamic range towards lower concentrations was often observed with the new API source. Matrix effects were quite similar between the two sources with a small, but statistically significant, lower percentage of matrix effects observed for the new API source in plasma and bile in the positive ion mode, and bile in negative ion mode for ESI. Finally, the sensitivity of late eluting compounds could be improved on the new API source by post-column addition of water.

Drug-induced liver injury (DILI) is the most common reason for failures during the drug development process and for safety-related withdrawal of drugs from the pharmaceutical market. Therefore, having tools and techniques that can detect hepatotoxic properties in drug candidates at an early discovery stage is highly desirable. In this study, cell imaging counting was used to measure in a fast, straightforward, and unbiased way the effect of paracetamol and tetracycline, (compounds known to cause hepatotoxicity in humans) on the amount of DsRed-labeled hepatocytes recovered by protease digestion from Tg(fabp10a:DsRed) transgenic zebrafish. The outcome was in general comparable with the results obtained using two reference methods, i.e., visual analysis of liver morphology by fluorescence microscopy and size analysis of fluorescent 2D liver images. In addition, our study shows that administering compounds into the yolk is relevant in the framework of hepatotoxicity testing. Taken together, cell imaging counting provides a novel and rapid tool for screening hepatotoxicants in early stages of drug development. This method is also suitable for testing of other organ-related toxicities subject to the organs and tissues expressing fluorescent proteins in transgenic zebrafish lines. ispartof: International Journal of Molecular Sciences vol:18 issue:2 ispartof: location:Switzerland status: published

WOS: 000389088700037, PubMed ID: 27837829, A specific and sensitive capillary liquid chromatography-ultraviolet detection (cap-LC-UV) method in combination with a micro-extraction by packed sorbent (MEPS) sample clean-up procedure has been developed and validated for the simultaneous analysis of chlorpromazine, olanzapine and their flavin-containing monooxygenase (FMO) mediated N-oxides in rat brain microdialysates. Chromatographic separation was obtained on an Acclaim Pepmap RP C18 column with an ID of 300 mu m. An injection volume of 20 L was used to inject the largely aqueous samples and was shown to have no influence on the obtained peak shape of the compounds of interest. Optimal conditions for MEPS extraction were obtained on a mixed-mode M1 (80% C8, 20% SCX) cartridge after diluting microdialysate samples with phosphate buffer pH 2.5 (1:3 v/v). The method was validated and lower limits of quantification (LLOQ) were determined at 0.5 nM for all compounds. Linearity was demonstrated between the LLOQ and 1 mu M for all compounds (R-2 > 0.995). MEPS recoveries were between 92% and 98%, with intra- and interday variabilities below 15%. The applicability of the developed method was successfully demonstrated by analysing rat brain microdialysates. The capillary LC-UV method in combination with MEPS sample treatment provides a simple, sensitive method to quantify all compounds of interest in 45 min and can be applied for routine therapeutic monitoring and pharmacokinetic studies of olanzapine, chlorpromazine and their respective N-oxides., Scientific and Technical Research Council of Turkey (TUBITAK) [113S036]; Research Foundation Flanders (FWO) [VS.054.13N.LC], This work was supported by the Scientific and Technical Research Council of Turkey (TUBITAK) (Project No. 113S036); and the Research Foundation Flanders (FWO) (Project No. VS.054.13N.LC).

After the great commercial success of sub-3 µm superficially porous particles, vendors are now also starting to commercialize 5 µm superficially porous particles, as an alternative to their fully porous counterparts which are routinely used in pharmaceutical analysis. In this study, the performance of 5 µm superficially porous particles was compared to that of fully porous 5 µm particles in terms of efficiency, separation performance and loadability on a conventional HPLC instrument. Van Deemter and kinetic plots were first used to evaluate the efficiency and performance of both particle types using alkylphenones as a test mixture. The van Deemter and kinetic plots showed that the superficially porous particles provide a superior kinetic performance compared to the fully porous particles over the entire relevant range of separation conditions, when both support types were evaluated at the same operating pressure. The same observations were made both for isocratic and gradient analysis. The superior performance was further demonstrated for the separation of a pharmaceutical compound (griseofulvin) and its impurities, where a gain in analysis time of around 2 could be obtained using the superficially porous particles. Finally, both particle types were evaluated in terms of loadability by plotting the resolution of the active pharmaceutical ingredient and its closest impurity as a function of the signal-to-noise ratio obtained for the smallest impurity. It was demonstrated that the superficially porous particles show better separation performance for griseofulvin and its impurities without significantly compromising sensitivity due to loadability issues in comparison with their fully porous counterparts. Moreover these columns can be used on conventional equipment without modifications to obtain a significant improvement in analysis time.

The kinetic performance of commercially available first generation and prototype second generation silica monoliths has been investigated for 2.0 mm and 3.0–3.2 mm inner diameter columns. It is demonstrated that the altered sol–gel process employed for the production of second generation monoliths results in structures with a smaller characteristic size leading to an improved peak shape and higher efficiencies. The permeability of the columns however, decreases significantly due to the smaller throughpore and skeleton sizes. Scanning electron microscopy pictures suggest the first generation monoliths have cylindrical skeleton branches, whereas the second generation monoliths rather have skeleton branches that resemble a single chain of spherical globules. Using recently established correlations for the flow resistance of cylindrical and globule chain type monolithic structures, it is demonstrated that the higher flow resistance of the second generation monoliths can be entirely attributed to their smaller skeleton sizes, which is also evident from the external porosity that is largely the same for both monolith generations ( ɛ e ∼ 0.65). The recorded van Deemter plots show a clear improvement in efficiency for the second generation monoliths (minimal plate heights of 13.6–14.1 μm for the first and 6.5–8.2 μm for the second generation, when assessing the plate count using the Foley–Dorsey method). The corresponding kinetic plots, however, indicate that the much reduced permeability of the second generation monoliths results in kinetic performances (time needed to achieve a given efficiency) which are only better than those of the first generation for plate counts up to N ∼ 45,000. For more complex samples ( N ≥ 50,000), the first generation monoliths can intrinsically still provide faster analysis due to their high permeability. It is also demonstrated that – despite the improved efficiency of the second generation monoliths in the practical range of separations ( N = 10,000–50,000) – these columns can still not compete with state-of-the-art core–shell particle columns when all columns are evaluated at their own maximum operating pressure (200 bar for the monolithic columns, 600 bar for core–shell columns). It is suggested that monolithic columns will only become competitive with these high efficiency particle columns when further improvements to their production process are made and their pressure resistance is raised.

Zebrafish-based platforms have recently emerged as a useful tool for toxicity testing as they combine the advantages of in vitro and in vivo methodologies. Nevertheless, the capacity to metabolically convert xenobiotics by zebrafish eleuthero embryos is supposedly low. To circumvent this concern, a comprehensive methodology was developed wherein test compounds (i.e., parathion, malathion and chloramphenicol) were first exposed in vitro to rat liver microsomes (RLM) for 1 h at 37 &deg, C. After adding methanol, the mixture was ultrasonicated, placed for 2 h at &minus, 20 &deg, C, centrifuged and the supernatant evaporated. The pellet was resuspended in water for the quantification of the metabolic conversion and the detection of the presence of metabolites using ultra high performance liquid chromatography-Ultraviolet-Mass (UHPLC-UV-MS). Next, three days post fertilization (dpf) zebrafish eleuthero embryos were exposed to the metabolic mix diluted in Danieau&rsquo, s medium for 48 h at 28 &deg, C, followed by a stereomicroscopic examination of the adverse effects induced, if any. The novelty of our method relies in the possibility to quantify the rate of the in vitro metabolism of the parent compound and to co-incubate three dpf larvae and the diluted metabolic mix for 48 h without inducing major toxic effects. The results for parathion show an improved predictivity of the toxic potential of the compound.

The intrinsic kinetic performance of three recently commercialized large size (≥4 μm) core–shell particles packed in columns with different lengths has been measured and compared with that of standard fully porous particles of similar and smaller size (5 and 3.5 μm, respectively). The kinetic performance is compared in both absolute (plot of t0 versus the plate count N or the peak capacity np for isocratic and gradient elution, respectively) and dimensionless units. The latter is realized by switching to so-called impedance plots, a format which has been previously introduced (as a plot of t0/N2 or E0 versus Nopt/N) and has in the present study been extended from isocratic to gradient elution (where the impedance plot corresponds to a plot of t0/np4 versus np,opt2/np2). Both the isocratic and gradient impedance plot yielded a very similar picture: the clustered impedance plot curves divide into two distinct groups, one for the core–shell particles (lowest values, i.e. best performance) and one for the fully porous particles (highest values), confirming the clear intrinsic kinetic advantage of core–shell particles. If used around their optimal flow rate, the core–shell particles displayed a minimal separation impedance that is about 40% lower than the fully porous particles. Even larger gains in separation speed can be achieved in the C-term regime.

A novel mixing unit is proposed for the serial coupling of orthogonal columns to analyze polar and non-polar compounds in a single run. The principle relies on the isolation of unretained peaks eluting from a first dimension column in a sample loop, before directing them to a second column for separation. Since the mobile phases employed in highly orthogonal separations are not directly compatible, a mixing unit is required to alter the mobile phase composition before executing the second dimension separation. The mixing unit proposed in this work is based on the use of two restriction capillaries with different flow resistances to dilute the mobile phase eluting from the first dimension with a solvent appropriate for the second dimension separation. The restriction capillaries are implemented in an ultra-high performance liquid chromatography set-up using three high-pressure switching valves and two T-pieces. It is demonstrated that the dilution ratio can be adequately predicted using the law of Hagen-Poiseuille and can be adjusted easily by changing the dimensions of the restriction capillaries. The dilution volume required to obtain acceptable recoveries is investigated and the use of different column diameters in the first and second dimension is proposed to increase the sensitivity of the analysis. Under optimum dilution conditions, recoveries ranging between 82% and 99% are always obtained, while repeatability values are excellent. The proof-of-concept of the different set-ups is demonstrated for the separation of 20 pharmaceuticals with log D-values ranging between -5.75 and 4.22.

A new atmospheric pressure ionization (API) source, viz. UniSpray, was evaluated for mass spectrometry (MS) analysis of pharmaceutical compounds by head-to-head comparison with electrospray ionization (ESI) on the same high-resolution MS system. The atmospheric pressure ionization source is composed of a grounded nebulizer spraying onto a high voltage, cylindrical stainless steel target. Molecules are ionized in a similar fashion to electrospray ionization, predominantly producing protonated or deprotonated species. Adduct formation (e.g., proton and sodium adducts) and in-source fragmentation is shown to be almost identical between the two sources. The performance of the new API source was compared with electrospray by infusion of a mix of 22 pharmaceutical compounds with a wide variety of functional groups and physico-chemical properties (molecular weight, logP, and pKa) in more than 100 different conditions (mobile phase strength, solvents, pH, and flow rate). The new API source shows an intensity gain of a factor 2.2 compared with ESI considering all conditions on all compounds tested. Finally, some hypotheses on the ionization mechanism, similarities, and differences with ESI, are discussed. Graphical Abstract ᅟ.

Appropriate analytical methods are required to evaluate the presence, metabolism, degradation, and removal of specific compounds in complex mixtures. There is an increasing demand to analyze samples with a wide range of polarities in a variety of applications, including environmental analysis, biomarker discovery, and proteomics. Multiple analyses on complementary columns are often needed to cover the separation of all compounds with a large difference in polarity. This article describes a generic method involving an ultrahigh-pressure liquid chromatography (UHPLC) system equipped with two external switching valves to connect hydrophilic interaction liquid chromatography (HILIC) and reversed phase LC columns in series for the sequential analysis of polar and apolar compounds. The method was successfully applied to separate 32 pharmaceutical compounds with a wide range of polarities, which could be useful for analyzing pharmaceutical compounds in the environment.

Diffusion plays an important role in all aspects of band broadening in chromatography. An accurate knowledge of molecular diffusion coefficients in different mobile phases is therefore crucial in fundamental column performance studies. Correlations available in literature, such as the Wilke-Chang equation, can provide good approximations of molecular diffusion under reversed-phase conditions. However, these correlations have been demonstrated to be less accurate for mobile phases containing a large percentage of acetonitrile, as is the case in hydrophilic interaction liquid chromatography.A database of experimentally measured molecular diffusion coefficients of some 45 polar and apolar compounds that are frequently used as test molecules under hydrophilic interaction liquid chromatography and reversed-phase conditions is therefore presented. Special attention is given to diffusion coefficients of polar compounds obtained in large percentages of acetonitrile (>90%). The effect of the buffer concentration (5-10mM ammonium acetate) on the obtained diffusion coefficients is investigated and is demonstrated to mainly influence the molecular diffusion of charged molecules.Diffusion coefficients are measured using the Taylor-Aris method and hence deduced from the peak broadening of a solute when flowing through a long open tube. The validity of the set-up employed for the measurement of the diffusion coefficients is demonstrated by ruling out the occurrence of longitudinal diffusion, secondary flow interactions and extra-column effects, while it is also shown that radial equilibration in the 15 m long capillary is effective. (C) 2016 Elsevier B.V. All rights reserved.

In the present study, the extraction kinetics of cobalt with Cyanex 272 in a flat membrane microcontactor is studied. Pseudo-first order and non-first order models are proposed to describe the extraction kinetics with acidic Cyanex 272 and saponified Cyanex 272. The impact of the acetate buffer concentration, the Cyanex 272 concentration, the feed concentration, the channel depth and saponification of Cyanex 272 on the extraction kinetics was experimentally measured. From this, it was shown that for acidic Cyanex 272 pseudo-first order reaction kinetics could be assumed under at least following conditions: (1) when the feed was buffered; (2) the Cyanex 272 concentration was 4.4 times higher than the cobalt concentration; and (3) the cobalt concentration remained below 17 mmol/L. In that case a linear model could be derived that could be solved analytically. At higher cobalt concentrations, saturation of the interface had to be taken into account, resulting in a non-linear model that had to be solved numerically. When Cyanex 272 was saponified, the extraction kinetics dropped significantly indicating that pseudo-first order kinetics does not apply any longer. Consequently, faster extraction kinetics in membrane contactors with acidic Cyanex 272 is obtained by buffering the feed phase compared to the saponification approach of Cyanex 272. (C) 2015 Elsevier B.V. All rights reserved.

A membrane microcontactor suitable to perform liquid-liquid extraction as well as evaporation in order to conduct enrichment steps in sample preparation of organ samples has been designed, fabricated, and characterized. Spacers of 100- or 200-μm high were constructed in a metal substrate with a channel width of 13 mm and the extraction kinetics in these channels was evaluated. The spacers were designed such that at the entrance and exit region a uniform flow distribution could take place and that a uniform flow profile could be guaranteed along the channel, hence allowing a large freedom in sample volume to be processed. The extraction and evaporation kinetic behavior of the device was first evaluated by extraction of a drug candidate (4-(2,5-dimethyl-pyrrol-1-y1)-2-hydroxybenzoic acid). To evaluate the device under more challenging working conditions, a homogenized mice kidney sample containing the drug candidate that was administered in life condition was cleaned and enriched with the extraction and evaporation modules and characterized by high-performance liquid chromatography, yielding an overall analysis time of 15-20 min per sample only. The system has the potential to be operated in a continuous fashion, making it appealing to be implemented in screening or high-throughput applications.

In LC method development, the choice of suitable experimental conditions is often challenging for the analyst because of the huge diversity of stationary phases, mobile phase pH and organic modifiers, that could significantly alter the selectivity. The influence of these parameters on selectivity was experimentally tested in both RPLC and HILIC conditions for the analysis of 45 pharmaceutical compounds covering a wide range of physico-chemical properties. Principal component analysis (PCA) models were built to assess the resulting multivariate dataset. The complementarity between RPLC and HILIC was clearly demonstrated. The importance of mobile phase pH as one of the main experimental factors to be considered was confirmed. The RPLC and HILIC methods were thus employed for the analysis of a drug cocktail containing two substrates and their numerous desmethylated metabolites. All the compounds were finally resolved in both modes, with a very distinct elution order. In addition, the possibility to combine columns of different selectivity was highlighted using a column coupler set-up and found to be extremely promising. The same type of experiments was also carried out for the impurity profiling of an antihistaminic drug. In this example, compounds of very distinct polarity were satisfactorily eluted in both RPLC and HILIC modes, using suitable conditions of pH and stationary phase. In conclusion, this study demonstrates the complementary and interest of RPLC and HILIC in the case of pharmaceutical method development.

The present contribution reviews the foundations of the kinetic-plot method for the direct comparison of the kinetic performance of different chromatographic support and operating modes. The method directly uses experimental data collected for a specific sample and operating condition of one's interest, and is applicable both under isocratic- and gradient-elution conditions. Experimental proof is provided for the strong relation between the kinetic performance of a given support under isocratic and gradient conditions: a material offering superior kinetic performances under isocratic conditions will remain superior under gradient conditions and vice versa provided the comparison occurs under unbiased conditions. In addition, a review is made of the recent literature using the kinetic-plot method to compare and assess the kinetic performance of high performance HPLC columns and their operation mode.

Using a set of experimentally determined liquid chromatography column performance data, it has been investigated how a range of efficiencies can best be covered when using a multi-column system. Two main variants are considered: a serially-connected variant (realizing different column lengths by connecting a different number of column segments in series) and a parallel-connected variant (realizing different column lengths by simply switching between columns with a different length arranged in parallel). Both variants are compared for their ability to keep the average analysis time along a given range of efficiencies as close as possible to the intrinsic Knox & Saleem-speed limit. It was found that the serial connection mode offers a better compromise between average speed and amount of required silica (total required column length) than the parallel connection mode for all efficiency ranges running from 5000-10,000 plates up to 75,000-150,000 plates. Considering an ultra-high performance liquid chromatography (UHPLC) operation at 1200 bar, the best possible serial connection system can get within about within 15-25% of the Knox & Saleem-speed limit, whereas a three-column parallel system can only get to within 40-50% of the speed limit, while needing 50-100% more total column length. In absolute terms, the serially-connected system with individually optimized segment lengths should be able to cover a range of 5000-75,000 theoretical plates (dynamic range of 25) in an average analysis time of 14.3 min when using a 1200 bar instrument. At 400 bar, this would be 37.9 min, showing that the construction of wide-efficiency range systems would be one of the application areas where the advantages of UHPLC-conditions would be most fully realized.

A protocol using trifluoroacetic acid at a temperature of 60 degrees C is developed for the adequate removal of the stationary phase of reversed-phase liquid chromatography (RPLC) columns. This procedure allows for studying the same column first under RPLC and subsequently under hydrophilic-interaction liquid chromatography (HILIC) conditions to isolate intrinsic differences between mass transfer properties in HILIC and RPLC from differences in packing quality. The established procedure allows for a complete removal of the stationary phase (confirmed by retention studies and thermogravimetry analyses) while leaving the structure of the packing unaffected (witnessed by an unchanged external porosity and pressure drop). Accurate plate height analysis comparing compounds at the same zone retention factor indicates a significant difference in reduced c-term (typically 40-80% larger under HILIC conditions), despite the columns otherwise being identical. Correcting for the known contributions of longitudinal diffusion (b-term) and mass transfer (c(m)- and c(s)-term) to focus on band broadening originating from eddy dispersion, similar strong differences are observed (differences of some h = 0.3 up to 1.2). These findings show that the interior structure and retention mechanism of the particles have a very strong effect on the observed eddy dispersion, a factor typically ascribed to phenomena occurring outside the particles. This also implies that comparing the quality of packings of different particle types is virtually impossible without the availability of a sound model to correct for the intraparticle effect on the observed eddy dispersion.

The development of a method for the separation of standard compounds of the 15 main phenolics found in rooibos tea is presented. The separation of these compounds in a single HPLC analysis is particularly challenging due to the similarity of rooibos phenolics. As a result, multiple methods are often required to analyze all major phenolics in rooibos tea samples. The method development process is significantly enhanced in this study by using the recently introduced automated column coupler in combination with the variable column length strategy. This strategy consists of performing the initial scouting runs, wherein the best separation conditions are determined, on a short column and subsequently fine-tuning the separation on longer columns to benefit from their higher separation performance. It is demonstrated that the method development process can further be expedited by operating each column length at the maximum pressure, in this case 1000 bar. Although this holds in general, it is even more the case for the presently considered sample, since the selectivity of the sample is more pressure- than temperature-dependent. Applying the optimized method to unfermented and fermented aqueous rooibos tea extracts in combination with Q-TOF mass spectrometry, some 30 phenolic compounds are tentatively identified.

Four fully porous C18 columns (Hypersil Gold, ACE3, Xbridge and Gemini NX), widely employed in the pharmaceutical industry, were compared in terms of efficiency and analysis speed with the Kinetic Plot Method. Weakly basic, medium-sized, N-containing pharmaceutical compounds from GlaxoSmithKline Research and Development were used as test molecules. Isocratic elution was carried out at pH 4.5 and pH 8.0 with acetonitrile as organic modifier. The columns under evaluation included highly pure silica supports (Hypersil Gold, ACE3) and hybrid polymer-silica supports (XBridge, Gemini NX). Both types of columns claim for nearly absent secondary interactions with ionized silanol groups and are therefore applicable in a wide pH range. This is an important feature for method development purposes in pharmaceutical industries. The Kinetic Plot Method was used to compare the support characteristics and assess the kinetic performance of the columns in different experimental conditions. Although the evaluated columns have roughly identical particle diameters (from 3.0 to 3.5 μm) according to their manufacturers, large differences in kinetic performance were observed at pH 4.5 that can be accounted for by different flow resistances, porosities and average particle diameters, experimentally determined from scanning electron microscopy and laser light scattering experiments on loose stationary phase material. The ACE3 column was the best performing support among the evaluated columns, due to its excellent efficiency and average flow resistance. The better performance of the ACE3 column was due to its better packing quality, as could be derived from its impedance plot. Kinetic plots of resolution of a critical pair versus analysis time and column length were established at pH 8.0. These plots can be used as a method development tool to tailor the separation conditions to the required resolution of a given critical pair, combining efficiency and selectivity features of the column.

A variable length method development (or VL-MD)strategy, exploiting the potential of an automatic column coupling system, is proposed and has been applied to a number of different pharmaceutical and environmental samples with a varying degree of complexity. The proposed strategy consistently produced separation methods that had at least an equally good critical pair resolution and an equally short run time to those of methods produced using commercially available MD assistance software. In some cases, the VL-MD strategy allowed the MD time to be drastically shortened from >30 h to an overnight run of only 12 h. The developed strategy has the potential to become fully automated provided that reliable chromatogram read-out software becomes available. The advantage of combining different stationary phase types to improve the available selectivity and the integration into the general VL-MD strategy was also demonstrated.

A recently introduced 2.5 μm fully porous support (Kromasil Eternity) is compared with three different brands of superficially porous material (Kinetex, Halo and Poroshell 120) by means of the kinetic plot method using pharmaceutical compounds from GlaxoSmithKline as probe molecules. The kinetic plot method immediately shows the range of plate numbers wherein a support performs better than another. Results from experiments carried out at pH 4.5 and 8.0 are presented in order to assess the pH stability of the tested phases. Moreover, since all supports are able to withstand pressures higher than 400 bar, they have been evaluated both on HPLC and UHPLC instrumentation. True average particle sizes were determined by SEM images taken from loose stationary phases. Kinetex outperforms the other columns in HPLC conditions for practically relevant efficiencies, but shows poor packing quality in the 100×2.1-mm format. Kromasil is advantageous for simple and fast separations on short columns both in HPLC and in UHPLC conditions. Halo achieves the highest efficiencies of all columns at the lowest pressure cost and shows a noticeable lower axial diffusion. Poroshell 120 has the best packing quality reproducibility across the tested formats. All columns preserve their performance at high pH.

The kinetic-plot approach, in which experimental t(0) and N-values are extrapolated to the performance at maximum system pressure by increasing the column length, was validated by coupling 250×3 mm columns packed with 3 μm particles. The extra-column volume introduced by coupling columns could be neglected with respect to the peak volumes. Plate numbers of up to 132,000 were experimentally achieved by coupling four columns. The maximum deviation between the experimental and predicted plate numbers was 7% for two coupled columns, and decreasing to 0.1% for four coupled columns. Kinetic plots were used to find the conditions to separate a critical pair, with a preset value for the effective plate number, in the shortest possible time. For high-efficiency separations yielding 100,000 effective plates, the optimum critical-pair retention factor was around 4.5. Kinetic plots are presented to find the optimal column length to obtain the fastest possible 100,000 effective-plate separation, taking into account the effect of mobile-phase viscosity on column pressure, and consequently the optimum column length.

As an alternative to the classical approach of combining strong cation exchange SCX-LC and RP-LC for the separation of complex proteomic samples, this essay describes the online comprehensive RP-LCxRP-LC separation of BSA and human blood serum. High orthogonality and peak capacity are achieved through the application of a significantly different pH in the two dimensions. The coupling of fused-core columns in series ensures high efficiency in the first dimension, while a previously designed interface with parallel second dimension columns further enhances the separation capability of the comprehensive system.

Peak parking experiments have been performed on three RP-HPLC different columns, using two different components and a variable mobile phase composition. The aim of the study was to investigate whether the B-term diffusion expressions currently used in the literature (which are all Knox-type models) should be replaced by the effective diffusion expressions that have been developed in the frame of the effective medium theory (EMT). Although the EMT-expressions are not fully accurate either (the mathematics of the complex interactions between different diffusion zones that are in close contact are too demanding to catch them in an exact analytical expression), they at least are physically sound and do not violate Maxwell's basic law of diffusion. Further they also provide a much better approximation of the numerically calculated effective diffusivity in the theoretical test situation considered in part I. The present study shows that the values of the surface or stationary phase diffusion coefficient that are derived from peak parking models can depend heavily on the employed B-term model. The EMT-based B-term expressions lead to values of the surface diffusion coefficient that vary much less strongly with the phase retention factor than if one of the Knox-type models is used to analyze the data. This implies that, since all peak parking experiments that have been performed in the past have all been interpreted with a Knox-type model, the conclusions that have been drawn from these studies should all be moderated or at least revisited.

The occurrence of turbulent flow conditions in the connection tubing or at the entrance of the detection flow cell has been identified as a potential source of excessive detector noise in the signal of the diode array UV-absorption detector flow cell of a commercial HPLC system used to perform high-speed separations on wide-bore columns (4.6 mm i.d.). This excessive noise was found to occur abruptly if the flow rate is increased beyond a certain critical value or during gradient runs, if the mobile phase viscosity falls below a certain critical value. Several detector cells of different dimensions were studied to investigate the dependency of the effect on the detector cell design and the system tubing. Evidence for the turbulent flow origin of this noise is that its onset always occurred at a given fixed value of the Reynolds number. This critical Reynolds number could also be used to predict the onset of detector noise during gradient elution runs. Second, evidence for the turbulent flow origin of the noise was that it could be reliably eliminated using a flow splitter after the column to reduce the flow rate below its critical value before entering the detector. The loss in separation efficiency and detection sensitivity accompanying this flow splitting solution was found to be so small that it does not weigh up against the huge advantage of the possibility to eliminate the excessive detector noise.

The pressure-drop characteristics of six sub-2 μm columns of three different manufacturers but with the same surface chemistry (C18) have been studied using the recently introduced total pore blocking method for the determination of the external porosity and by using scanning electron microscopy pictures to measure the actual size of the particles. Having used the Sauter-mean particle size to correctly account for the particle size spread, and having corrected for the influence of the intra-particle porosity, it was found that all columns yielded Kozeny–Carman constant (fKC) values close to 180, in agreement with the theory. This agreement could subsequently be used to quantify how the different system parameters such as mean particle size, packing density and intra-particle porosity (all tending to vary significantly from manufacturer to manufacturer) each contributes to the observed total bed permeability. Small (upward) deviations from the fKC = 180-value could be correlated to a larger width of the particle size distribution, and more notably to the existence of a high size ratio of the largest to the smallest particles present in the particle batches.

Using a set of experimentally determined plate height data obtained on three commercial high-temperature HPLC supports, and evaluating their isocratic separation speed potential under the application of a set of instrumental constraints, a qualitative map of the practically achievable critical pair separation speed potential of high-temperature HPLC has been established. The obtained data show that the gain in separation speed is more strongly affected by the instrumental limitations in the high-temperature range than it is for the low temperatures. For the presently considered case of alkylbenzene separations, the potential gain in analysis time that can be obtained by going from T = 30 to 120 °C in the presence of a typical set of instrumental limitations nevertheless remains of the order of a factor of 2–4. The study also shows that improvements on the instrumentation side (increased detector frequency, pumping flow rate, smaller extra-column volumes, …) are indispensable to fully benefit from the high temperature advantages for all separations requiring less than 10,000 effective theoretical plates.

The present study aimed at mapping the separation speed potential of a critical pair on commercial high-temperature HPLC (HT-HPLC) supports at elevated temperatures. For this purpose, band broadening and pressure drop measurements were conducted on three different commercial HT-HPLC columns operated at various elevated temperatures but by keeping the same retention factor. The plate height data were subsequently transformed into a plot showing the minimal required analysis time needed to yield a given required effective plate number. For the considered RPLC alkylbenzene separations, it was found that the maximal gain in separation speed of the critical pair that can be obtained by varying the operating temperature from T=30 to 120 degrees C can be expected to be of the order of a factor of 3-4, if using an individually optimized column length for each considered temperature and if no secondary adsorption effects occur at the lower temperature. This gain factor, remaining more or less constant over the most relevant range of plate numbers, largely paralleled the reduction of the mobile phase viscosity accompanying the temperature increase.

Hydrophilic interaction chromatography (HILIC) is being increasingly used for the analysis of hydrophilic compounds in biological matrices. The complexity of biological samples demands adequate sample preparation procedures, specifically adjusted for HILIC analyses. Currently, most bioanalytical assays are performed on bare silica and ZIC-HILIC columns. Trends in HILIC for bioanalysis include smaller particle sizes and miniaturization of the analytical column. For complex biological samples, multidimensional techniques can separate and identify more compounds than 1D separations. The high volatility of the mobile phase, the added separation power and high sensitivity make MS the detection method of choice for bioanalysis using HILIC, although other detectors such as evaporative light scattering detection, charged aerosol detection and nuclear magnetic resonance have been reported.

We discuss the most important plot types for the kinetic performance of liquid chromatography columns and elaborate on how these plots should best be constructed and can be made dimensionless. Distinction is made between plots that are most suited for practitioners (column users) versus those most suited for theoreticians and column manufacturers.

Structural elucidation of metabolites is an important part during the discovery and development process of new pharmaceutical drugs. Liquid Chromatography (LC) in combination with Mass Spectrometry (MS) is usually the technique of choice for structural identification but cannot always provide precise structural identification of the studied metabolite (e.g. site of hydroxylation and site of glucuronidation). In order to identify those metabolites, different approaches are used combined with MS data including nuclear magnetic resonance, hydrogen/deuterium exchange and chemical derivatization followed by LC-MS. Those techniques are often time-consuming and/or require extra sample pre-treatment. In this paper, a fast and easy to set up tool using desorption electrospray ionization-MS for metabolite identification is presented. In the developed method, analytes in solution are simply dried on a glass plate with printed Teflon spots and then a single drop of derivatization mixture is added. Once the spot is dried, the derivatized compound is analyzed. Six classic chemical derivatizations were adjusted to work as a one drop reaction and applied on a list of compounds with relevant functional groups. Subsequently, two successive reactions on a single spot of amoxicillin were tested and the methodology described was successfully applied on an in vitro incubated alprazolam metabolite. All reactions and analyses were performed within an hour and gave useful structural information by derivatizing functional groups, making the method a time-saving and efficient tool for metabolite identification if used in addition or in some cases as an alternative to common methods. ispartof: Journal of Mass Spectrometry vol:50 issue:7 pages:871-878 ispartof: location:England status: published

This chapter is intended as a basic introduction to microchip-based capillary electrophoresis to set the scene for newcomers and give pointers to reference material. An outline of some commonly used setups and key concepts is given, many of which are explored in greater depth in later chapters.