Search

The utilization of carbon-fiber-reinforced polymer (CFRP) composites as strengthening materials for structural components has become quite famous over the last couple of decades. The present experimental study was carried out to examine the effect of varied widths of externally bonded CFRP on the debonding strain of CFRP and the failure mode of plain concrete beams. Twelve plain concrete prims measuring 100 mm × 100 mm × 500 mm were cast and tested under identical loading conditions. The twelve specimens include two control prisms, i.e., without CFRP strips, and the remaining ten prisms were reinforced with CFRP strips with widths of 10 mm, 20 mm, 30 mm, 40 mm, and 50 mm, respectively, i.e., two prisms in each group. Four-point loading flexural testing was carried out, and the resulting data are presented in the form of peak load vs. midpoint displacement, load vs. concrete strain, and load vs. CFRP strain. The peak load was directly recorded from the testing machine, while the midpoint deflection was recorded through the linear variable differential transducer (LVDT) installed at the midpoint. To measure the strain, two separate strain gauges were installed at the bottom of each concrete prism, i.e., one on the concrete surface and the other on the surface of the CFRP strip. The results of this study indicate that the debonding strain is a function of CFRP strip width and that the failure patterns of beams are significantly affected by the CFRP reinforcement ratio.

The safety and economy of an infrastructure project depends on the material and design equations used to simulate the performance of a particular member. A variety of materials can be used in conjunction to achieve a composite action, such as a hollow steel section filled with concrete, which can be successfully utilized in the form of an axially loaded member. This study aims to model the ultimate compressive strength (P u ) of concrete-filled hollow steel sections (CFSS) by formulating a mathematical expression using gene expression programming (GEP). A total of 149 datapoints were obtained from the literature, considering ten input parameters, including the outer diameter of steel tube (D), wall thickness of steel tube, compressive strength of concrete (f c '), elastic modulus of concrete (E c ), yield strength of steel (f v ), elastic modulus of steel (E s ), length of the column (L), confinement factor (ζ), ratio of D to thickness of column, and the ratio of length to D of column. The performance of the developed models was assessed using coefficient of regression R 2 , root mean squared error RMSE, mean absolute error MAE and comparison of regression slopes. It was found that the optimal GEP Model T3, having number of chromosomes N c = 100, head size H s = 8 and number of genes N g = 3, outperformed all the other models. For this particular model, R 2 overall equaled 0.99, RMSE values were 133.4 and 162.2, and MAE = 92.4 and 108.7, for training (TR) and testing (TS) phases, respectively. Similarly, the comparison of regression slopes analysis revealed that the Model T3 exhibited the highest R 2 of 0.99 with m = 1, in both the TR and TS stages, respectively. Finally, parametric analysis showed that the P u of composite steel columns increased linearly with the value of D, t and f y .

The useful life of a concrete structure is highly dependent upon its durability, which enables it to withstand the harsh environmental conditions. Resistance of a concrete specimen to rapid chloride ion penetration (RCP) is one of the tests to indirectly measure its durability. The central aim of this study was to investigate the influence of different variables, such as, age, amount of binder, fine aggregate, coarse aggregate, water to binder ratio, metakaolin content and the compressive strength of concrete on the RCP resistance using a genetic programming approach. The number of chromosomes (N c ), genes (N g ) and, the head size (H s ) of the gene expression programming (GEP) model were varied to study their influence on the predicted RCP values. The performance of all the GEP models was assessed using a variety of performance indices, i.e., R 2 , RMSE and comparison of regression slopes. The optimal GEP model (Model T3) was obtained when the N c = 100, H s = 8 and N g = 3. This model exhibits an R 2 of 0.89 and 0.92 in the training and testing phases, respectively. The regression slope analysis revealed that the predicted values are in good agreement with the experimental values, as evident from their higher R 2 values. Similarly, parametric analysis was also conducted for the best performing Model T3. The analysis showed that the amount of binder, compressive strength and age of the sample enhanced the RCP resistance of the concrete specimens. Among the different input variables, the RCP resistance sharply increased during initial stages of curing (28-d), thus validating the model results.

Estimating concrete properties using soft computing techniques has been shown to be a time and cost-efficient method in the construction industry. Thus, for the prediction of steel fiber-reinforced concrete (SFRC) strength under compressive and flexural loads, the current research employed advanced and effective soft computing techniques. In the current study, a single machine learning method known as multiple-layer perceptron neural network (MLPNN) and ensembled machine learning models known as MLPNN-adaptive boosting and MLPNN-bagging are used for this purpose. Water; cement; fine aggregate (FA); coarse aggregate (CA); super-plasticizer (SP); silica fume; and steel fiber volume percent (Vf SF), length (mm), and diameter were the factors considered (mm). This study also employed statistical analysis such as determination coefficient (R 2 ), root mean square error (RMSE), and mean absolute error (MAE) to assess the performance of the algorithms. It was determined that the MLPNN-AdaBoost method is suitable for forecasting SFRC compressive and flexural strengths. The MLPNN technique's higher R 2 , i.e., 0.94 and 0.95 for flexural and compressive strength, respectively, and lower error values result in more precision than other methods with lower R 2 values. SHAP analysis demonstrated that the volume of cement and steel fibers have the greatest feature values for SFRC's compressive and flexural strengths, respectively.

The outcomes of acute coronary syndromes (ACS) vary internationally, given regional differences in patient co-morbidities, access to health care, interventional procedures and adherence to guideline-based management practices. This study aimed to identify the predictors of mortality from a large ACS registry of patients admitted to a tertiary care cardiac centre in Dhaka, Bangladesh. This was a hospital record based retrospective cross sectional observational study that included all patients presenting with ACS to Ibrahim Cardiac Hospital and Research Institute, Dhaka, Bangladesh from January 2013 to December 2013. Data were collected from cardiac catheterization laboratory database and hospital discharge records. Statistical analysis was done using Statistical Package for Social Sciences (SPSS) version 16.0. A p value <0.05 was considered statistically significant. Ethical approval was obtained by Institutional Review Board of the hospital. A total of 1914 ACS patients were studied: 39.8% presented with ST-elevation myocardial infarction (STEMI), 39.7% with non-ST-elevation myocardial infarction (NSTEMI) and 20.5% with unstable angina (UA). There were 146 in-hospital deaths (7.6%). Mortality was highest among STEMI patients (10.5%), followed by NSTEMI (8.1%) and UA (1.03%). The mean age of expired patients was significantly higher than that of those who survived (64.82±12.14 years vs. 57.32±11.99 years; p<0.001). Male patients were 71.4%, with no significant gender differences observed between expired and surviving groups. Age >50 years {odds ratio (OR) 2.56, p=0.005}, chronic kidney disease (CKD) (OR 2.1, p<0.001), shock (OR 16.82, p<0.001), left ventricular failure (LVF) (OR 2.43, p<0.001) and STEMI (OR 1.92, p=0.002) were independent predictors of mortality among ACS patients. Although diabetes per se was not associated with mortality (OR 1.3; 95% CI=0.89-1.91; p=0.169), uncontrolled diabetes defined as HbA1c levels ≥7.5% had significant risk of mortality (OR 51.4, p<0.001). ACS patients who did not undergo angiography (OR 16.4; p<0.001) or PCI (OR 18.9; p<0.001) had greater risk of mortality. ACS patients complicated with shock, LVF, uncontrolled diabetes and CKD had increased risk of in-hospital mortality. Improved outcomes may be likely with prompt angiography and PCI during index admission. This study is a preliminary initiative, and prospective multi-centre registries with nation-wide involvement are warranted.

In this study, compressive strength (CS) of fiber-reinforced nano-silica concrete (FRNSC) was anticipated using ensemble machine learning (ML) approaches. Four types of ensemble ML methods were employed, including gradient boosting, random forest, bagging regressor, and AdaBoost regressor, to achieve the study's aims. The validity of employed models was tested and compared using the statistical tests, coefficient of determination (R 2 ), and k-fold method. Moreover, a Shapley Additive Explanations (SHAP) analysis was used to observe the interaction and effect of input parameters on the CS of FRNSC. Six input features, including fiber volume, coarse aggregate to fine aggregate ratio, water to binder ratio, nano-silica, superplasticizer to binder ratio, and specimen age, were used for modeling. In predicting the CS of FRNSC, it was observed that gradient boosting was the model of lower accuracy and the AdaBoost regressor had the highest precision in forecasting the CS of FRNSC. However, the performance of random forest and the bagging regressor was also comparable to that of the AdaBoost regressor model. The R 2 for the gradient boosting, random forest, bagging regressor, and AdaBoost regressor models were 0.82, 0.91, 0.91, and 0.92, respectively. Also, the error values of the models further validated the exactness of the ML methods. The average error values for the gradient boosting, random forest, bagging regressor, and AdaBoost regressor models were 5.92, 4.38, 4.24, and 3.73 MPa, respectively. SHAP study discovered that the coarse aggregate to fine aggregate ratio shows a greater negative correlation with FRNSC's CS. However, specimen age affects FRNSC CS positively. Nano-silica, fiber volume, and the ratio of superplasticizer to binder have both positive and deleterious effects on the CS of FRNSC. Employing these methods will promote the building sector by presenting fast and economical methods for calculating material properties and the impact of raw ingredients.

In order to forecast the axial load-carrying capacity of concrete-filled steel tubular (CFST) columns using principal component analysis (PCA), this work compares hybrid models of artificial neural networks (ANNs) and meta-heuristic optimization algorithms (MOAs). In order to create hybrid ANN models, a dataset of 149 experimental tests was initially gathered from the accessible literature. Eight PCA-based hybrid ANNs were created using eight MOAs, including artificial bee colony, ant lion optimization, biogeography-based optimization, differential evolution, genetic algorithm, grey wolf optimizer, moth flame optimization and particle swarm optimization. The created ANNs' performance was then assessed. With R 2 ranges between 0.7094 and 0.9667 in the training phase and between 0.6883 and 0.9634 in the testing phase, we discovered that the accuracy of the built hybrid models was good. Based on the outcomes of the experiments, the generated ANN-GWO (hybrid model of ANN and grey wolf optimizer) produced the most accurate predictions in the training and testing phases, respectively, with R 2 = 0.9667 and 0.9634. The created ANN-GWO may be utilised as a substitute tool to estimate the load-carrying capacity of CFST columns in civil engineering projects according to the experimental findings.

Recently, artificial intelligence (AI) approaches have gained the attention of researchers in the civil engineering field for estimating the mechanical characteristics of concrete to save the effort, time, and cost of researchers. Consequently, the current research focuses on assessing steel-fiber-reinforced concrete (SFRC) in terms of flexural strength (FS) prediction by employing delicate AI techniques as well as to predict the raw material interaction that is still a research gap. In this study, the FS of SFRC is estimated by deploying supervised machine learning (ML) techniques, such as DT-Gradient Boosting, DT-XG Boost, DT-AdaBoost, and DT-Bagging. In addition to that, the performance model is also evaluated by using R 2 , root mean square error (RMSE), and mean absolute error (MAE). Furthermore, the k-fold cross-validation method is also applied to validate the model's performance. It is observed that DT-Bagging with an R 2 value of 0.95 is superior to DT-XG Boost, DT-Gradient Boosting, and DT-AdaBoost. Lesser error MAE and RMSE and higher R 2 values for the DT-Bagging model show the enhanced performance of the model compared to the other ensembled approaches. Considerable conservation of time, effort, and cost can be made by applying ML techniques to predict concrete properties. The evaluation of the outcome depicts that the estimated results of DT-Bagging are closer to the experimental results, indicating the accurate estimation of SFRC flexural strength. It is further revealed from the SHapley Additive exPlanations (SHAP) study that the volumetric content of steel fiber highly and positively influences the FS of SFRC.

This study performed a scientometric-based examination of the literature on steel fiber-reinforced concrete (SFRC) to identify its key elements. Typical review papers are limited in their capacity to link distinct segments of the literature in an organized and systematic method. The most challenging aspects of current research are knowledge mapping, co-occurrence, and co-citation. The Scopus search engine was used to search for and obtain the data required to meet the goals of the study. During the data evaluation, the relevant publication sources, keyword assessment, productive authors based on publications and citations, top papers based on citations received, and areas vigorously involved in SFRC studies were recognized. The VOSviewer software tool was used to evaluate the literature data from 9562 relevant papers, which included citation, abstract, bibliographic, keywords, funding, and other information. Furthermore, the applications and constraints related to the usage of SFRC in the construction sector were examined, as well as potential solutions to these constraints. It was determined that only 17 publication sources (journals/conferences) had published at least 100 articles on SFRC up to June 2022. Additionally, the mostly employed keywords by authors in SFRC research include steel fibers, fiber-reinforced concrete, concrete, steel fiber-reinforced concrete, and reinforced concrete. The assessment of authors revealed that 39 authors had published at least 30 articles. Moreover, China, the United States, and India were found to be the most active and participating countries based on publications on SFRC research. This study can assist academics in building collaborative initiatives and communicating new ideas and techniques because of the quantitative and graphical depiction of participating nations and researchers.

A scientometric-based assessment of the literature on geopolymers was conducted in this study to determine its critical aspects. Typical review studies are restricted in their capability to link disparate segments of the literature in a systematic and exact way. Knowledge mapping, co-citation, and co-occurrence are very difficult components of creative research. This study adopted an advanced strategy of data mining, data processing and analysis, visualization and presentation, and interpretation of the bibliographic data on geopolymers. The Scopus database was used to search for and retrieve the data needed to complete the study's objectives. The relevant sources of publications, keyword assessment, productive authors based on publications and citations, top papers based on citations received, and areas actively engaged in the research of geopolymers are recognized during the data assessment. The VOSviewer (VOS: visualization of similarities) software application was employed to analyze the literature data comprising citation, bibliographic, abstract, keywords, funding, and other information from 7468 relevant publications. In addition, the applications and restrictions associated with the use of geopolymers in the construction sector are discussed, as well as possible solutions to overcome these restrictions. The scientometric analysis revealed that the leading publication source (journal) in terms of articles and citations is "Construction and building materials"; the mostly employed keywords are geopolymer, fly ash, and compressive strength; and the top active and contributing countries based on publications are China, India, and Australia. Because of the quantitative and graphical representation of participating nations and researchers, this study can help academics to create collaborative efforts and exchange creative ideas and approaches. In addition, this study concluded that the large-scale usage of geopolymer concrete is constrained by factors such as curing regime, activator solution scarcity and expense, efflorescence, and alkali-silica reaction. However, embracing the potential solutions outlined in this study might assist in boosting the building industry's adoption of geopolymer concrete.

The goal of this work was to use a hybrid ensemble machine learning approach to estimate the interfacial bond strength (IFB) of fibre-reinforced polymer laminates (FRPL) bonded to the concrete using the results of a single shear-lap test. A database comprising 136 data was used to train and validate six standalone machine learning models, namely, artificial neural network (ANN), extreme machine learning (ELM), the group method of data handling (GMDH), multivariate adaptive regression splines (MARS), least square-support vector machine (LSSVM), and Gaussian process regression (GPR). The hybrid ensemble (HENS) model was subsequently built, employing the combined and trained predicted outputs of the ANN, ELM, GMDH, MARS, LSSVM, and GPR models. In comparison with the standalone models employed in the current investigation, it was observed that the suggested HENS model generated superior predicted accuracy with R 2 (training = 0.9783, testing = 0.9287), VAF (training = 97.83, testing = 92.87), RMSE (training = 0.0300, testing = 0.0613), and MAE (training = 0.0212, testing = 0.0443). Using the training and testing dataset to assess the predictive performance of all models for IFB prediction, it was discovered that the HENS model had the greatest predictive accuracy throughout both stages with an R 2 of 0.9663. According to the findings of the experiments, the newly developed HENS model has a great deal of promise to be a fresh approach to deal with the overfitting problems of CML models and thus may be utilised to forecast the IFB of FRPL.

This study aimed to determine how radiation attenuation would change when the thickness, density, and compressive strength of clay bricks, modified with partial replacement of clay by fly ash, iron slag, and wood ash. To conduct this investigation, four distinct types of bricks-normal, fly ash-, iron slag-, and wood ash-incorporated bricks were prepared by replacing clay content with their variable percentages. Additionally, models for predicting the radiation-shielding ability of bricks were created using gene expression programming (GEP) and artificial neural networks (ANN). The addition of iron slag improved the density and compressive strength of bricks, thus increasing shielding capability against gamma radiation. In contrast, fly ash and wood ash decreased the density and compressive strength of burnt clay bricks, leading to low radiation shielding capability. Concerning the performance of the Artificial Intelligence models, the root mean square error (RMSE) was determined as 0.1166 and 0.1876 nC for the training and validation data of ANN, respectively. The training set values for the GEP model manifested an RMSE equal to 0.2949 nC, whereas the validation data produced RMSE = 0.3507 nC. According to the statistical analysis, the generated models showed strong concordance between experimental and projected findings. The ANN model, in contrast, outperformed the GEP model in terms of accuracy, producing the lowest values of RMSE. Moreover, the variables contributing towards shielding characteristics of bricks were studied using parametric and sensitivity analyses, which showed that the thickness and density of bricks are the most influential parameters. In addition, the mathematical equation generated from the GEP model denotes its significance such that it can be used to estimate the radiation shielding of burnt clay bricks in the future with ease.

The depletion of natural resources of river sand and its availability issues as a construction material compelled the researchers to use manufactured sand. This study investigates the compressive strength of concrete made of manufactured sand as a partial replacement of normal sand. The prediction model, i.e., gene expression programming (GEP), was used to estimate the compressive strength of manufactured sand concrete (MSC). A database comprising 275 experimental results based on 11 input variables and 1 target variable was used to train and validate the developed models. For this purpose, the compressive strength of cement, tensile strength of cement, curing age, Dmax of crushed stone, stone powder content, fineness modulus of the sand, water-to-binder ratio, water-to-cement ratio, water content, sand ratio, and slump were taken as input variables. The investigation of a varying number of genetic characteristics, such as chromosomal number, head size, and gene number, resulted in the creation of 11 alternative models (M1-M11). The M5 model outperformed other created models for the training and testing stages, with values of (4.538, 3.216, 0.919) and (4.953, 3.348, 0.906), respectively, according to the results of the accuracy evaluation parameters root mean square error (RMSE), mean absolute error (MAE), and coefficient of determination (R2). The R2 and error indices values revealed that the experimental and projected findings are in extremely close agreement. The best model has 200 chromosomes, 8 head sizes, and 3 genes. The mathematical expression achieved from the GEP model revealed that six parameters, namely the compressive and tensile strength of cement, curing period, water−binder ratio, water−cement ratio, and stone powder content contributed effectively among the 11 input variables. The sensitivity analysis showed that water−cement ratio (46.22%), curing period (25.43%), and stone powder content (13.55%) were revealed as the most influential variables, in descending order. The sensitivity of the remaining variables was recorded as w/b (11.37%) > fce (2.35%) > fct (1.35%).

The Kingdom of Saudi Arabia generates an enormous amount of date palm waste, causing severe environmental concerns. Green and strong concrete is increasingly demanded due to low carbon footprints and better performance. In this research work, biochar derived from locally available agriculture waste (date palm fronds) was used as an additive to produce high-strength and durable concrete. Mechanical properties such as compressive and flexural strength were evaluated at 7, 14, and 28 days for control and all other mixes containing biochar. In addition, the durability properties of the concrete samples for the mixes were investigated by performing electric resistivity and ultra-sonic pulse velocity testing. Finally, a SWOT (strengths, weaknesses, opportunities, and threats) analysis was carried out to make strategic decisions about biochar’s use in concrete. The results demonstrated that the compressive strength of concrete increased to 28−29% with the addition of 0.75−1.5 wt% of biochar. Biochar-concrete containing 0.75 wt% of biochar showed 16% higher flexural strength than the control specimen. The high ultrasonic pulse velocity (UPV) values (>7.79 km/s) and low electrical resistivity (<22.4 kΩ-cm) of biochar-based concrete confirm that the addition of biochar resulted in high-quality concrete free from internal flaws, cracks, and better structural integrity. SWOT analysis indicated that biochar-based concrete possessed improved performance than ordinary concrete, is suitable for extreme environments, and has opportunities for circular economy and applications in various construction designs. However, cost and technical shortcomings in biochar production and biochar-concrete mix design are still challenging.

The current work presents a comparative study of hybrid models that use support vector machines (SVMs) and meta-heuristic optimization algorithms (MOAs) to predict the ultimate interfacial bond strength (IBS) capacity of fiber-reinforced polymer (FRP). More precisely, a dataset containing 136 experimental tests was first collected from the available literature for the development of hybrid SVM models. Five MOAs, namely the particle swarm optimization, the grey wolf optimizer, the equilibrium optimizer, the Harris hawks optimization and the slime mold algorithm, were used; five hybrid SVMs were constructed. The performance of the developed SVMs was then evaluated. The accuracy of the constructed hybrid models was found to be on the higher side, with R 2 ranges between 0.8870 and 0.9774 in the training phase and between 0.8270 and 0.9294 in the testing phase. Based on the experimental results, the developed SVM-HHO (a hybrid model that uses an SVM and the Harris hawks optimization) was overall the most accurate model, with R 2 values of 0.9241 and 0.9241 in the training and testing phases, respectively. Experimental results also demonstrate that the developed hybrid SVM can be used as an alternate tool for estimating the ultimate IBS capacity of FRP concrete in civil engineering projects.

Steel-fiber-reinforced concrete (SFRC) has been introduced as an effective alternative to conventional concrete in the construction sector. The incorporation of steel fibers into concrete provides a bridging mechanism to arrest cracks, improve the post-cracking behavior of concrete, and transfer stresses in concrete. Artificial intelligence (AI) approaches are in use nowadays to predict concrete properties to conserve time and money in the construction industry. Accordingly, this study aims to apply advanced and sophisticated machine-learning (ML) algorithms to predict SFRC compressive strength. In the current work, the applied ML approaches were gradient boosting, random forest, and XGBoost. The considered input variables were cement, fine aggregates (sand), coarse aggregates, water, silica fume, super-plasticizer, fly ash, steel fiber, fiber diameter, and fiber length. Previous studies have not addressed the effects of raw materials on compressive strength in considerable detail, leaving a research gap. The integration of a SHAP analysis with ML algorithms was also performed in this paper, addressing a current research need. A SHAP analysis is intended to provide an in-depth understanding of the SFRC mix design in terms of its strength factors via complicated, nonlinear behavior and the description of input factor contributions by assigning a weighing factor to each input component. The performances of all the algorithms were evaluated by applying statistical checks such as the determination coefficient (R 2 ), the root mean square error (RMSE), and the mean absolute error (MAE). The random forest ML approach had a higher, i.e., 0.96, R 2 value with fewer errors, producing higher precision than other models with lesser R 2 values. The SFRC compressive strength could be anticipated by applying the random forest ML approach. Further, it was revealed from the SHapley Additive exPlanations (SHAP) analysis that cement content had the highest positive influence on the compressive strength of SFRC. In this way, the current study is beneficial for researchers to effectively and quickly evaluate SFRC compressive strength.

Nowadays, concretes blended with pozzolanic additives such as fly ash (FA), silica fume (SF), slag, etc., are often used in construction practices. The utilization of pozzolanic additives and industrial by-products in concrete and grouting materials has an important role in reducing the Portland cement usage, the CO 2 emissions, and disposal issues. Thus, the goal of the present work is to estimate the compressive strength (CS) of polyethylene terephthalate (PET) and two supplementary cementitious materials (SCMs), namely FA and SF, blended cementitious grouts to produce green mix. For this purpose, five hybrid least-square support vector machine (LSSVM) models were constructed using swarm intelligence algorithms, including particle swarm optimization, grey wolf optimizer, salp swarm algorithm, Harris hawks optimization, and slime mold algorithm. To construct and validate the developed hybrid models, a sum of 156 samples were generated in the lab with varying percentages of PET and SCM. To estimate the CS, five influencing parameters, namely PET, SCM, FLOW, 1-day CS (CS 1D ), and 7-day CS (CS 7D ), were considered. The performance of the developed models was assessed in terms of multiple performance indices. Based on the results, the proposed LSSVM-PSO (a hybrid model of LSSVM and particle swarm optimization) was determined to be the best performing model with R 2 = 0.9708, RMSE = 0.0424, and total score = 40 in the validation phase. The results of sensitivity analysis demonstrate that all the input parameters substantially impact the 28-day CS (CS 28D ) of cementitious grouts. Among them, the CS 7D has the most significant effect. From the experimental results, it can be deduced that PET/SCM has no detrimental impact on CS 28D of cementitious grouts, making PET a viable alternative for generating sustainable and green concrete. In addition, the proposed LSSVM-PSO model can be utilized as a novel alternative for estimating the CS of cementitious grouts, which will aid engineers during the design phase of civil engineering projects.

Incorporating waste material, such as recycled coarse aggregate concrete (RCAC), into construction material can reduce environmental pollution. It is also well-known that the inferior properties of recycled aggregates (RAs), when incorporated into concrete, can impact its mechanical properties, and it is necessary to evaluate the optimal performance. Accordingly, artificial intelligence has been used recently to evaluate the performance of concrete compressive behaviour for different types of construction material. Therefore, supervised machine learning techniques, i.e., DT-XG Boost, DT-Gradient Boosting, SVM-Bagging, and SVM-Adaboost, are executed in the current study to predict RCAC's compressive strength. Additionally, SHapley Additive exPlanations (SHAP) analysis shows the influence of input parameters on the compressive strength of RCAC and the interactions between them. The correlation coefficient (R 2 ), root mean square error (RMSE), and mean absolute error (MAE) are used to assess the model's performance. Subsequently, the k-fold cross-validation method is executed to validate the model's performance. The R 2 value of 0.98 from DT-Gradient Boosting supersedes those of the other methods, i.e., DT- XG Boost, SVM-Bagging, and SVM-Adaboost. The DT-Gradient Boosting model, with a higher R 2 value and lower error (i.e., MAE, RMSE) values, had a better performance than the other ensemble techniques. The application of machine learning techniques for the prediction of concrete properties would consume fewer resources and take less time and effort for scholars in the respective engineering field. The forecasting of the proposed DT-Gradient Boosting models is in close agreement with the actual experimental results, as indicated by the assessment output showing the improved estimation of RCAC's compressive strength.

Interface yield stress (YS) and plastic viscosity (PV) have a significant impact on the pumpability of concrete mixes. This study is based on the application of predictive machine learning (PML) techniques to forecast the rheological properties of fresh concrete. The artificial neural network (NN) and random forest (R-F) PML approaches were introduced to anticipate the PV and YS of concrete. In comparison, the R-F model outperforms the NN model by giving the coefficient of determination (R 2 ) values equal to 0.92 and 0.96 for PV and YS, respectively. In contrast, the model's legitimacy was also verified by applying statistical checks and a k-fold cross validation approach. The mean absolute error, mean square error, and root mean square error values for R-F models by investigating the YS were noted as 30.36 Pa, 1141.76 Pa, and 33.79 Pa, respectively. Similarly, for the PV, these values were noted as 3.52 Pa·s, 16.48 Pa·s, and 4.06 Pa·s, respectively. However, by comparing these values with the NN's model, they were found to be higher, which also gives confirmation of R-F's high precision in terms of predicting the outcomes. A validation approach known as k-fold cross validation was also introduced to authenticate the precision of employed models. Moreover, the influence of the input parameters was also investigated with regard to predictions of PV and YS. The proposed study will be beneficial for the researchers and construction industries in terms of saving time, effort, and cost of a project.

In recent times, the use of fibre-reinforced plastic (FRP) has increased in reinforcing concrete structures. The bond strength of FRP rebars is one of the most significant parameters for characterising the overall efficacy of the concrete structures reinforced with FRP. However, in cases of elevated temperature, the bond of FRP-reinforced concrete can deteriorate depending on a number of factors, including the type of FRP bars used, its diameter, surface form, anchorage length, concrete strength, and cover thickness. Hence, accurate quantification of FRP rebars in concrete is of paramount importance, especially at high temperatures. In this study, an artificial intelligence (AI)-based genetic-expression programming (GEP) method was used to predict the bond strength of FRP rebars in concrete at high temperatures. In order to predict the bond strength, we used failure mode temperature, fibre type, bar surface, bar diameter, anchorage length, compressive strength, and cover-to-diameter ratio as input parameters. The experimental dataset of 146 tests at various elevated temperatures were established for training and validating the model. A total of 70% of the data was used for training the model and remaining 30% was used for validation. Various statistical indices such as correlation coefficient (R), the mean absolute error (MAE), and the root-mean-square error (RMSE) were used to assess the predictive veracity of the GEP model. After the trials, the optimum hyperparameters were 150, 8, and 4 as number of chromosomes, head size and number of genes, respectively. Different genetic factors, such as the number of chromosomes, the size of the head, and the number of genes, were evaluated in eleven separate trials. The results as obtained from the rigorous statistical analysis and parametric study show that the developed GEP model is robust and can predict the bond strength of FRP rebars in concrete under high temperature with reasonable accuracy (i.e., R, RMSE and MAE 0.941, 2.087, and 1.620, and 0.935, 2.370, and 2.046, respectively, for training and validation). More importantly, based on the FRP properties, the model has been translated into traceable mathematical formulation for easy calculations.

The presence of high levels of carcinogenic metalloid arsenic (As) in the groundwater system of Bangladesh has been considered as one of the major environmental disasters in this region. Many parts of Bangladesh have extensively reported the presence of high levels of arsenic in the groundwater due to both geological and anthropogenic activities. In this paper, we reviewed the available literature and scientific information regarding arsenic pollution in Bangladesh, including arsenic chemistry and occurrences. Along with using As-rich groundwater as a drinking-water source, the agricultural activities and especially irrigation have greatly depended on the groundwater resources in this region due to high water demands for ensuring food security. A number of investigations in Bangladesh have shown that high arsenic content in both soil and groundwater may result in high levels of arsenic accumulation in different plants, including cereals and vegetables. This review provides information regarding arsenic accumulation in major rice varieties, soil-groundwater-rice arsenic interaction, and past arsenic policies and plans, as well as previously implemented arsenic mitigation options for both drinking and irrigation water systems in Bangladesh. In conclusion, this review highlights the importance and necessity for more in-depth studies as well as more effective arsenic mitigation action plans to reduce arsenic incorporation in the food chain of Bangladesh., (© 2022. The Author(s).)

Concrete is an economical and efficient material for attenuating radiation. The potential of concrete in attenuating radiation is attributed to its density, which in turn depends on the mix design of concrete. This paper presents the findings of a study conducted to evaluate the radiation attenuation with varying water-cement ratio ( w / c ), thickness, density, and compressive strength of concrete. Three different types of concrete, i.e., normal concrete, barite, and magnetite containing concrete, were prepared to investigate this study. The radiation attenuation was calculated by studying the dose absorbed by the concrete and the linear attenuation coefficient. Additionally, artificial neural network (ANN) and gene expression programming (GEP) models were developed for predicting the radiation shielding capacity of concrete. A correlation coefficient (R), mean absolute error (MAE), and root mean square error (RMSE) were calculated as 0.999, 1.474 mGy, 2.154 mGy and 0.994, 5.07 mGy, 5.772 mGy for the training and validation sets of the ANN model, respectively. Similarly, for the GEP model, these values were recorded as 0.981, 13.17 mGy, and 20.20 mGy for the training set, whereas the validation data yielded R = 0.985, MAE = 12.2 mGy, and RMSE = 14.96 mGy. The statistical evaluation reflects that the developed models manifested close agreement between experimental and predicted results. In comparison, the ANN model surpassed the accuracy of the GEP models, yielding the highest R and the lowest MAE and RMSE. The parametric and sensitivity analysis revealed the thickness and density of concrete as the most influential parameters in contributing towards radiation shielding. The mathematical equation derived from the GEP models signifies its importance such that the equation can be easily used for future prediction of radiation shielding of high-density concrete.

Research on the applications of new techniques such as machine learning is advancing rapidly. Machine learning methods are being employed to predict the characteristics of various kinds of concrete such as conventional concrete, recycled aggregate concrete, geopolymer concrete, fiber-reinforced concrete, etc. In this study, a scientometric-based review on machine learning applications for concrete was performed in order to evaluate the crucial characteristics of the literature. Typical review studies are limited in their capacity to link divergent portions of the literature systematically and precisely. Knowledge mapping, co-citation, and co-occurrence are among the most challenging aspects of innovative studies. The Scopus database was chosen for searching for and retrieving the data required to achieve the study's aims. During the data analysis, the relevant sources of publications, relevant keywords, productive writers based on publications and citations, top articles based on citations received, and regions actively engaged in research into machine learning applications for concrete were identified. The citation, bibliographic, abstract, keyword, funding, and other data from 1367 relevant documents were retrieved and analyzed using the VOSviewer software tool. The application of machine learning in the construction sector will be advantageous in terms of economy, time-saving, and reduced requirement for effort. This study can aid researchers in building joint endeavors and exchanging innovative ideas and methods, due to the statistical and graphical portrayal of participating authors and countries.

Stabilized aggregate bases are vital for the long-term service life of pavements. Their stiffness is comparatively higher; therefore, the inclusion of stabilized materials in the construction of bases prevents the cracking of the asphalt layer. The effect of wet−dry cycles (WDCs) on the resilient modulus (Mr) of subgrade materials stabilized with CaO and cementitious materials, modelled using artificial neural network (ANN) and gene expression programming (GEP) has been studied here. For this purpose, a number of wet−dry cycles (WDC), calcium oxide to SAF (silica, alumina, and ferric oxide compounds in the cementitious materials) ratio (CSAFRs), ratio of maximum dry density to the optimum moisture content (DMR), confining pressure (σ3), and deviator stress (σ4) were considered input variables, and Mr was treated as the target variable. Different ANN and GEP prediction models were developed, validated, and tested using 30% of the experimental data. Additionally, they were evaluated using statistical indices, such as the slope of the regression line between experimental and predicted results and the relative error analysis. The slope of the regression line for the ANN and GEP models was observed as (0.96, 0.99, and 0.94) and (0.72, 0.72, and 0.76) for the training, validation, and test data, respectively. The parametric analysis of the ANN and GEP models showed that Mr increased with the DMR, σ3, and σ4. An increase in the number of WDCs reduced the Mr value. The sensitivity analysis showed the sequences of importance as: DMR > CSAFR > WDC > σ4 > σ3, (ANN model) and DMR > WDC > CSAFR > σ4 > σ3 (GEP model). Both the ANN and GEP models reflected close agreement between experimental and predicted results; however, the ANN model depicted superior accuracy in predicting the Mr value.

Geopolymers might be the superlative alternative to conventional cement because it is produced from aluminosilicate-rich waste sources to eliminate the issues associated with its manufacture and use. Geopolymer composites (GPCs) are gaining popularity, and their research is expanding. However, casting, curing, and testing specimens requires significant effort, price, and time. For research to be efficient, it is essential to apply novel approaches to the said objective. In this study, compressive strength (CS) of GPCs was anticipated using machine learning (ML) approaches, i.e., one single method (support vector machine (SVM)) and two ensembled algorithms (gradient boosting (GB) and extreme gradient boosting (XGB)). All models' validity and comparability were tested using the coefficient of determination (R2), statistical tests, and k-fold analysis. In addition, a model-independent post hoc approach known as SHapley Additive exPlanations (SHAP) was employed to investigate the impact of input factors on the CS of GPCs. In predicting the CS of GPCs, it was observed that ensembled ML strategies performed better than the single ML technique. The R2 for the SVM, GB, and XGB models were 0.98, 0.97, and 0.93, respectively. The lowered error values of the models, including mean absolute and root mean square errors, further verified the enhanced precision of the ensembled ML approaches. The SHAP analysis revealed a stronger positive correlation between GGBS and GPC's CS. The effects of NaOH molarity, NaOH, and Na 2 SiO 3 were also observed as more positive. Fly ash and gravel size: 10/20 mm have both beneficial and negative impacts on the GPC's CS. Raising the concentration of these ingredients enhances the CS, whereas increasing the concentration of GPC reduces it. Gravel size: 4/10 mm has less favorable and more negative effects. ML techniques will benefit the construction sector by offering rapid and cost-efficient solutions for assessing material characteristics.

Sustainable development involves the usage of alternative sustainable materials in order to sustain the excessive depletion of natural resources. Plant fibers, as a "green" material, are progressively gaining the attention of various researchers in the field of construction for their potential use in composites for stepping towards sustainable development. This study aims to provide a scientometric review of the summarized background of plant fibers and their applications as construction and building materials. Studies from the past two decades are summarized. Quantitative assessment of research progress is made by using connections and maps between bibliometric data that are compiled for the analysis of plant fibers using Scopus. Data refinement techniques are also used. Plant fibers are potentially used to enhance the mechanical properties of a composite. It is revealed from the literature that plant-fiber-reinforced composites have comparable properties in comparison to composites reinforced with artificial/steel fibers for civil engineering applications, such as construction materials, bridge piers, canal linings, soil reinforcement, pavements, acoustic treatment, insulation materials, etc. However, the biodegradable nature of plant fibers is still a hindrance to their application as a structural material. For this purpose, different surface and chemical treatment methods have been proposed in past studies to improve their durability. It can be surmised from the gathered data that the compressive and flexural strengths of plant-fiber-reinforced cementitious composites are increased by up to 43% and 67%, respectively, with respect to a reference composite. In the literature, alkaline treatment has been reported as an effective and economical method for treating plant fibers. Environmental degradation due to excessive consumption of natural resources and fossil fuels for the construction industry, along with the burning of waste plant fibers, can be reduced by incorporating said fibers in cementitious composites to reduce landfill pollution and, ultimately, achieve sustainable development.

Coal mining waste in the form of coal gangue (CG) was established recently as a potential fill material in earthworks. To ascertain this potential, this study forecasts the strength and California Bearing Ratio (CBR) characteristics of chemically stabilized CG by deploying two widely used artificial intelligence approaches, i.e., artificial neural network (ANN) and random forest (RF) regression. In this research work, varied dosage levels of lime (2, 4, and 6%) and gypsum (0.5, 1, and 1.5%) were employed for determining the unconfined compression strength (UCS) and CBR of stabilized CG mixes. An experimental study comprising 384 datasets was conducted and the resulting database was used to develop the ANN and RF regression models. Lime content, gypsum dosage, and 28 d curing period were considered as three input attributes in obtaining three outputs (i.e., UCS, unsoaked CBR, and soaked CBR). While modelling with the ANN technique, different algorithms, hidden layers, and the number of neurons were studied while selecting the optimum model. In the case of RF regression modelling, optimal grid comprising maximal depth of tree, number of trees, confidence, random splits, enabled parallel execution, and guess subset ratio were investigated, alongside the variable number of folds, to obtain the best model. The optimum models obtained using the ANN approach manifested relatively better performance in terms of correlation coefficient values, equaling 0.993, 0.995, and 0.997 for UCS, unsoaked CBR and soaked CBR, respectively. Additionally, the MAE values were observed as 45.98 kPa, 1.41%, and 1.18% for UCS, unsoaked CBR, and soaked CBR, respectively. The models were also validated using 2-stage validation processes. In the first stage of validation of the model (using unseen 30% of the data), it was revealed that reliable performance of the models was attained, whereas in the second stage (parametric analysis), results were achieved which are corroborated with those in existing literature.

Sustainable concrete is gaining in popularity as a result of research into waste materials, such as recycled aggregate (RA). This strategy not only protects the environment, but also meets the demand for concrete materials. Using advanced artificial intelligence (AI) approaches, this study anticipates the split tensile strength (STS) of concrete samples incorporating RA. Three machine-learning techniques, artificial neural network (ANN), decision tree (DT), and random forest (RF), were examined for the specified database. The results suggest that the RF model shows high precision compared with the DT and ANN models at predicting the STS of RA-based concrete. The high value of the coefficient of determination and the low error values of the mean absolute error (MAE), mean square error (MSE), and root mean square error (RMSE) provided significant evidence for the accuracy and precision of the RF model. Furthermore, statistical tests and the k-fold cross-validation technique were used to validate the models. The importance of the input parameters and their contribution levels was also investigated using sensitivity analysis and SHAP analysis.

Recently, the high demand for marble stones has progressed in the construction industry, ultimately resulting in waste marble production. Thus, environmental degradation is unavoidable because of waste generated from quarry drilling, cutting, and blasting methods. Marble waste is produced in an enormous amount in the form of odd blocks and unwanted rock fragments. Absence of a systematic way to dispose of these marble waste massive mounds results in environmental pollution and landfills. To reduce this risk, an effort has been made for the incorporation of waste marble powder into concrete for sustainable construction. Different proportions of marble powder are considered as a partial substitute in concrete. A total of 40 mixes are prepared. The effectiveness of marble in concrete is assessed by comparing the compressive strength with the plain mix. Supervised machine learning algorithms, bagging (Bg), random forest (RF), AdaBoost (AdB), and decision tree (DT) are used in this study to forecast the compressive strength of waste marble powder concrete. The models' performance is evaluated using correlation coefficient (R 2 ), root mean square error, and mean absolute error and mean square error. The achieved performance is then validated by using the k-fold cross-validation technique. The RF model, having an R 2 value of 0.97, has more accurate prediction results than Bg, AdB, and DT models. The higher R 2 values and lesser error (RMSE, MAE, and MSE) values are the indicators for better performance of RF model among all individual and ensemble models. The implementation of machine learning techniques for predicting the mechanical properties of concrete would be a practical addition to the civil engineering domain by saving effort, resources, and time.

Several review studies have been performed on nano-silica-modified concrete, but this study adopted a new method based on scientometric analysis for the keywords' assessment in the current research area. A scientometric analysis can deal with vast bibliometric data using a software tool to evaluate the diverse features of the literature. Typical review studies are limited in their ability to comprehensively and accurately link divergent areas of the literature. Based on the analysis of keywords, this study highlighted and described the most significant segments in the research of nano-silica-modified concrete. The challenges associated with using nano-silica were identified, and future research is directed. Moreover, prediction models were developed using data from the literature for the strength estimation of nano-silica-modified concrete. It was noted that the application of nano-silica in cement-based composites is beneficial when used up to an optimal dosage of 2-3% due to high pozzolanic reactivity and a filler effect, whereas a higher dosage of nano-silica has a detrimental influence due to the increased porosity and microcracking caused by the agglomeration of nano-silica particles. The mechanical strength might enhance by 20-25% when NS is incorporated in the optimal amount. The prediction models developed for predicting the strength of nano-silica-modified concrete exhibited good agreement with experimental data due to lower error values. This type of analysis may be used to estimate the essential properties of a material, therefore saving time and money on experimental tests. It is recommended to investigate cost-effective methods for the dispersion of nano-silica in higher concentrations in cement mixes; further in-depth studies are required to develop more accurate prediction models to predict nano-silica-modified concrete properties.

Rapid industrialization is leading to the pollution of underground natural soil by alkali concentration which may cause problems for the existing expansive soil in the form of producing expanding lattices. This research investigates the effect of stabilizing alkali-contaminated soil by using fly ash. The influence of alkali concentration (2 N and 4 N) and curing period (up to 28 days) on the unconfined compressive strength (UCS) of fly ash (FA)-treated (10%, 15%, and 20%) alkali-contaminated kaolin and black cotton (BC) soils was investigated. The effect of incorporating different dosages of FA (10%, 15%, and 20%) on the UCS kaolin and UCS BC soils was also studied. Sufficient laboratory test data comprising 384 data points were collected, and multi expression programming (MEP) was used to create tree-based models for yielding simple prediction equations to compute the UCS kaolin and UCS BC soils. The experimental results reflected that alkali contamination resulted in reduced UCS (36% and 46%, respectively) for the kaolin and BC soil, whereas the addition of FA resulted in a linear rise in the UCS. The optimal dosage was found to be 20%, and the increase in UCS may be attributed to the alkali-induced pozzolanic reaction and subsequent gain of the UCS due to the formation of calcium-based hydration compounds (with FA addition). Furthermore, the developed models showed reliable performance in the training and validation stages in terms of regression slopes, R, MAE, RMSE, and RSE indices. Models were also validated using parametric and sensitivity analysis which yielded comparable variation while the contribution of each input was consistent with the available literature.

An accurate calculation of the flexural capacity of flexural members is vital for the safe and economical design of FRP reinforced structures. The existing empirical models are not accurately calculating the flexural capacity of beams and columns. This study investigated the estimation of the flexural capacity of beams using non-linear capabilities of two Artificial Intelligence (AI) models, namely Artificial neural network (ANN) and Random Forest (RF) Regression. The models were trained using optimized hyperparameters obtained from the trial-and-error method. The coefficient of correlation (R), Mean Absolute Error, and Root Mean Square Error (RMSE) were observed as 0.99, 5.67 kN-m, and 7.37 kN-m, for ANN, while 0.97, 7.63 kN-m, and 8.02 kN-m for RF regression model, respectively. Both models showed close agreement between experimental and predicted results; however, the ANN model showed superior accuracy and flexural strength performance. The parametric and sensitivity analysis of the ANN models showed that an increase in bottom reinforcement, width and depth of the beam, and increase in compressive strength increased the bending moment capacity of the beam, which shows the predictions by the model are corroborated with the literature. The sensitivity analysis showed that variation in bottom flexural reinforcement is the most influential parameter in yielding flexural capacity, followed by the overall depth and width of the beam. The change in elastic modulus and ultimate strength of FRP manifested the least importance in contributing flexural capacity.

Atmospheric pollution has become a critical problem for modern society; therefore, the research in this area continually aims to develop a high-performance gas sensor for health care and environmental safety. Researchers have made a significant contribution in this field by developing highly sensitive sensor-based novel selective materials. The aim of this article is to review recent developments and progress in the selective and sensitive detection of environmentally toxic gases. Different classifications of gas sensor devices are discussed based on their structure, the materials used, and their properties. The mechanisms of the sensing devices, identified by measuring the change in physical property using adsorption/desorption processes as well as chemical reactions on the gas-sensitive material surface, are also discussed. Additionally, the article presents a comprehensive review of the different morphologies and dimensions of mixed heterostructure, multilayered heterostructure, composite, core-shell, hollow heterostructure, and decorated heterostructure, which tune the gas-sensing properties towards hazardous gases. The article investigates in detail the growth and interface properties, concentrating on the material configurations that could be employed to prepare nanomaterials for commercial gas-sensing devices.

Rice husk ash (RHA) is a significant pollutant produced by agricultural sectors that cause a malignant outcome to the environment. To encourage the re-use of RHA, this work used multi expression programming (MEP) to construct an empirical model for forecasting the compressive nature of concrete made with RHA (CRHA) as a cement substitute. Thus, the compressive strength of CRHA was developed comprising of 192 findings from the broad and trustworthy database obtained from literature review. The most significant characteristics, namely the specimen's age, the percentage of RHA, the amount of cement, superplasticizer, aggregates, and the amount of water, were used as input for the modeling of CRHA. External validation, sensitivity analysis, statistical checks, and Shapley Additive Explanations (SHAP) analysis were used to evaluate the models' performance. It was discovered that the most significant factors impacting the compressive strength of CRHA are the age of the concrete sample (AS), the amount of cement (C) and the amount of aggregate (A). The findings of this study have the potential to increase the re-use of RHA in the production of green concrete, hence promoting environmental protection and financial gain.

Polymers are long-chain, highly molecular weight molecules containing large numbers of repeating units within their backbone derived from the product of polymerization of monomeric units. The materials exhibit unique properties based on the types of bonds that exist within their structures. Among these, some behave as rubbers because of their excellent bending ability, lightweight nature, and shape memory. Moreover, their tunable chemical, structural, and electrical properties make them promising candidates for their use as sensing materials. Polymer-based sensors are highly utilized in the current scenario in the public health sector and environment control due to their rapid detection, small size, high sensitivity, and suitability in atmospheric conditions. Therefore, the aim of this review article is to highlight the current progress in polymer-based sensors. More importantly, this review provides general trends and challenges in sensor technology based on polymer materials.

Rebars made of fiber-reinforced plastic (FRP) might be the future reinforcing material, replacing mild steel rebars, which are prone to corrosion. The bond characteristics of FRP rebars differ from those of mild steel rebars due to their different stress-strain behavior than mild steel. As a result, determining the bond strength (BS) qualities of FRP rebars is critical. In this work, BS data for FRP rebars was investigated, utilizing non-linear capabilities of gene expression programming (GEP) on 273 samples. The BS of FRP and concrete was considered a function of bar surface ( Bs ), bar diameter ( d b ), concrete compressive strength ( f c '), concrete-cover-bar-diameter ratio ( c / d ), and embedment-length-bar-diameter ratio ( l / d ). The investigation of the variable number of genetic parameters such as number of chromosomes, head size, and number of genes was undertaken such that 11 different models (M1-M11) were created. The results of accuracy evaluation parameters, namely coefficient of determination (R 2 ), mean absolute error (MAE), and root mean square error (RMSE) imply that the M11 model outperforms other created models for the training and testing stages, with values of (0.925, 0.751, 1.08) and (0.9285, 0.802, 1.11), respectively. The values of R 2 and error indices showed that there is very close agreement between the experimental and predicted results. 30 number chromosomes, 9 head size, and 5 genes yielded the optimum model. The parametric analysis revealed that d b , c / d , and l / d significantly affected the BS. The FRP rebar diameter size is greater than 10 mm, whereas a l / d ratio of more than 12 showed a considerable decrease in BS. In contrast, the rise in c / d ratio revealed second-degree increasing trend of BS.

The application of supplementary cementitious materials (SCMs) in concrete has been reported as the sustainable approach toward the appropriate development. This research aims to compare the result of compressive strength (C-S) obtained from the experimental method and results estimated by employing the various modeling techniques for the fly-ash-based concrete. Although this study covers two aspects, an experimental approach and modeling techniques for predictions, the emphasis of this research is on the application of modeling methods. The physical and chemical properties of the cement and fly ash, water absorption and specific gravity of the aggregate used, surface area of the cement, and gradation of the aggregate were analyzed in the laboratory. The four predictive machine learning (PML) algorithms, such as decision tree (DT), multi-linear perceptron (MLP), random forest (RF), and bagging regressor (BR), were investigated to anticipate the C-S of concrete. Results reveal that the RF model was observed more exact in investigating the C-S of concrete containing fly ash (FA), as opposed to other employed PML techniques. The high R2 value (0.96) for the RF model indicates the high precision level for forecasting the required output as compared to DT, MLP, and BR model R 2 results equal 0.88, 0.90, and 0.93, respectively. The statistical results and cross-validation (C-V) method also confirm the high predictive accuracy of the RF model. The highest contribution level of the cement towards the prediction was also reported in the sensitivity analysis and showed a 31.24% contribution. These PML methods can be effectively employed to anticipate the mechanical properties of concretes.

Cement production is one of the major sources of decomposition of carbonates leading to the emission of carbon dioxide. Researchers have proven that incorporating industrial wastes is of paramount significance for producing green concrete due to the benefits of reducing cement production. The compressive strength of concrete is an imperative parameter to consider when designing concrete structures. Considering high prediction capabilities, artificial intelligence models are widely used to estimate the compressive strength of concrete mixtures. A variety of artificial intelligence models have been developed in the literature; however, evaluation of the modeling procedure and accuracy of the existing models suggests developing such models that manifest the detailed evaluation of setting parameters on the performance of models and enhance the accuracy compared to the existing models. In this study, the computational capabilities of the adaptive neurofuzzy inference system (ANFIS), gene expression programming (GEP), and gradient boosting tree (GBT) were employed to investigate the optimum ratio of ground-granulated blast furnace slag (GGBFS) and fly ash (FA) to the binder content. The training process of GEP modeling revealed 200 chromosomes, 5 genes, and 12 head sizes as the best hyperparameters. Similarly, ANFIS hybrid subclustering modeling with aspect ratios of 0.5, 0.1, 7, and 150; learning rate; maximal depth; and number of trees yielded the best performance in the GBT model. The accuracy of the developed models suggests that the GBT model is superior to the GEP, ANFIS, and other models that exist in the literature. The trained models were validated using 40% of the experimental data along with parametric and sensitivity analysis as second level validation. The GBT model yielded correlation coefficient (R), mean absolute error (MAE), and root mean square error (RMSE), equaling 0.95, 3.07 MPa, and 4.80 MPa for training, whereas, for validation, these values were recorded as 0.95, 3.16 MPa, and 4.85 MPa, respectively. The sensitivity analysis revealed that the aging of the concrete was the most influential parameter, followed by the addition of GGBFS. The effect of the contributing parameters was observed, as corroborated in the literature.

The application of artificial intelligence approaches like machine learning (ML) to forecast material properties is an effective strategy to reduce multiple trials during experimentation. This study performed ML modeling on 481 mixes of geopolymer concrete with nine input variables, including curing time, curing temperature, specimen age, alkali/fly ash ratio, Na 2 SiO 3 /NaOH ratio, NaOH molarity, aggregate volume, superplasticizer, and water, with CS as the output variable. Four types of ML models were employed to anticipate the compressive strength of geopolymer concrete, and their performance was compared to find out the most accurate ML model. Two individual ML techniques, support vector machine and multi-layer perceptron neural network, and two ensembled ML methods, AdaBoost regressor and random forest, were employed to achieve the study's aims. The performance of all models was confirmed using statistical analysis, k-fold evaluation, and correlation coefficient (R 2 ). Moreover, the divergence of the estimated outcomes from those of the experimental results was noted to check the accuracy of the models. It was discovered that ensembled ML models estimated the compressive strength of the geopolymer concrete with higher precision than individual ML models, with random forest having the highest accuracy. Using these computational strategies will accelerate the application of construction materials by decreasing the experimental efforts.

Reinforced concrete structures are subjected to frequent maintenance and repairs due to steel reinforcement corrosion. Fiber-reinforced polymer (FRP) laminates are widely used for retrofitting beams, columns, joints, and slabs. This study investigated the non-linear capability of artificial intelligence (AI)-based gene expression programming (GEP) modelling to develop a mathematical relationship for estimating the interfacial bond strength (IBS) of FRP laminates on a concrete prism with grooves. The model was based on five input parameters, namely axial stiffness ( E f t f ), width of FRP plate ( b f ), concrete compressive strength ( f c '), width of groove ( b g ), and depth of the groove ( h g ), and IBS was considered the target variable. Ten trials were conducted based on varying genetic parameters, namely the number of chromosomes, head size, and number of genes. The performance of the models was evaluated using the correlation coefficient (R), mean absolute error (MAE), and root mean square error (RMSE). The genetic variation revealed that optimum performance was obtained for 30 chromosomes, 11 head sizes, and 4 genes. The values of R, MAE, and RMSE were observed as 0.967, 0.782 kN, and 1.049 kN for training and 0.961, 1.027 kN, and 1.354 kN. The developed model reflected close agreement between experimental and predicted results. This implies that the developed mathematical equation was reliable in estimating IBS based on the available properties of FRPs. The sensitivity and parametric analysis showed that the axial stiffness and width of FRP are the most influential parameters in contributing to IBS.

ZnFe 2 O 4 as an anode that is believed to attractive. Due to its large theoretical capacity, this electrode is ideal for Lithium-ion batteries. However, the performance of ZnFe 2 O 4 while charging and discharging is limited by its volume growth. In the present study, carbon-coated ZnFe 2 O 4 is synthesized by the sol-gel method. Carbon is coated on the spherical surface of ZnFe 2 O 4 by in situ coating. In situ carbon coating alleviates volume expansion during electrochemical performance and Lithium-ion mobility is accelerated, and electron transit is accelerated; thus, carbon-coated ZnFe 2 O 4 show good electrochemical performance. After 50 cycles at a current density of 0.1 A·g -1 , the battery had a discharge capacity of 1312 mAh·g -1 and a capacity of roughly 1220 mAh·g -1 . The performance of carbon-coated ZnFe 2 O 4 as an improved anode is electrochemically used for Li-ion energy storage applications.

The emission of greenhouse gases and natural-resource depletion caused by the production of ordinary Portland cement (OPC) have a detrimental effect on the environment. Thus, an alternative means is required to produce eco-friendly concrete such as geopolymer concrete (GPC). However, GPC has a complex cementitious matrix and an ambiguous mix design. Aside from that, the composition and proportions of materials utilized may have an impact on the compressive strength. Similarly, the use of robust and efficient machine-learning (ML) approaches is now required to forecast the strength of such a composite cementitious matrix. As a result, this study anticipated the compressive strength of GPC with waste resources using ensemble and non-ensemble ML algorithms. This was accomplished through the use of Anaconda (Python). To build a strong ensemble learner by integrating weak learners, adaptive boosting, random forest (RF), and ensemble learner bagging were employed. Furthermore, ensemble learners were utilized on non-ensemble or weak learners, such as decision trees (DT) and support vector machines (SVM) via regression. The data encompassed 156 statistical samples in which nine variables, namely superplasticizer (kg/m 3 ), fly ash (kg/m 3 ), ground granulated blast-furnace slag (GGBS), temperature (°C), coarse and fine aggregate (kg/m 3 ), sodium silicate (Na 2 SiO 3 ), and sodium hydroxide (NaOH), were chosen to anticipate the results. Exploring it in depth, twenty sub-models with ensemble boosting and bagging approaches were trained, and tuning was performed to achieve the highest possible coefficient of determination (R 2 ). Moreover, cross K-Fold validation analysis and statistical checks were performed via indicators for the evaluation of the models. The result revealed that ensemble approaches yielded robust performance compared to non-ensemble algorithms. Generally, an ensemble learner with the RF and bagging approach on a DT yielded robust performance by achieving a better R 2 as 0.93, and with the lowest statistical errors. The communal model in artificial-intelligence analysis, on average, improved the accuracy of the model.

This study aimed to carry out a scientometric review of rice husk ash (RHA) concrete to assess the various aspects of the literature. Conventional review studies have limitations in terms of their capacity to connect disparate portions of the literature in a comprehensive and accurate manner. Science mapping, co-occurrence, and co-citation are a few of the most difficult phases of advanced research. The sources with the most articles, co-occurrences of keywords, the most prolific authors in terms of publications and citations, and areas actively involved in RHA concrete research are identified during the analysis. The Scopus database was used to extract bibliometric data for 917 publications that were then analyzed using the VOSviewer (version: 1.6.17) application. This study will benefit academics in establishing joint ventures and sharing innovative ideas and strategies because of the statistical and graphical representation of contributing authors and countries.

Numerous tests are used to determine the performance of concrete, but compressive strength (CS) is usually regarded as the most important. The recycled aggregate concrete (RAC) exhibits lower CS compared to natural aggregate concrete. Several variables, such as the water-cement ratio, the strength of the parent concrete, recycled aggregate replacement ratio, density, and water absorption of recycled aggregate, all impact the RAC's CS. Many studies have been carried out to ascertain the influence of each of these elements separately. However, it is difficult to investigate their combined effect on the CS of RAC experimentally. Experimental investigations entail casting, curing, and testing samples, which require considerable work, expense, and time. It is vital to adopt novel methods to the stated aim in order to conduct research quickly and efficiently. The CS of RAC was predicted in this research utilizing machine learning techniques like decision tree, gradient boosting, and bagging regressor. The data set included eight input variables, and their effect on the CS of RAC was evaluated. Coefficient correlation (R 2 ), the variance between predicted and experimental outcomes, statistical checks, and k-fold evaluations, were carried out to validate and compare the models. With an R 2 of 0.92, the bagging regressor technique surpassed the decision tree and gradient boosting in predicting the strength of RAC. The statistical assessments also validated the superior accuracy of the bagging regressor model, yielding lower error values like mean absolute error (MAE) and root mean square error (RMSE). MAE and RMSE values for the bagging model were 4.258 and 5.693, respectively, which were lower than the other techniques employed, i.e., gradient boosting (MAE = 4.956 and RMSE = 7.046) and decision tree (MAE = 6.389 and RMSE = 8.952). Hence, the bagging regressor is the best suitable technique to predict the CS of RAC.

Cement and concrete are among the major contributors to CO 2 emissions in modern society. Researchers have been investigating the possibility of replacing cement with industrial waste in concrete production to reduce its environmental impact. Therefore, the focus of this paper is on the effective use of wheat straw ash (WSA) together with silica fume (SF) as a cement substitute to produce high-performance and sustainable concrete. Different binary and ternary mixes containing WSA and SF were investigated for their mechanical and microstructural properties and global warming potential (GWP). The current results indicated that the binary and ternary mixes containing, respectively, 20% WSA (WSA20) and 33% WSA together with 7% SF (WSA33SF7) exhibited higher strengths than that of control mix and other binary and ternary mixes. The comparative lower apparent porosity and water absorption values of WSA20 and WSA33SF7 among all mixes also validated the findings of their higher strength results. Moreover, SEM-EDS and FTIR analyses has revealed the presence of dense and compact microstructure, which are mostly caused by formation of high-density calcium silicate hydrate (C-S-H) and calcium hydroxide (C-H) phases in both blends. FTIR and TGA analyses also revealed a reduction in the portlandite phase in these mixes, causing densification of microstructures and pores. Additionally, N 2 adsorption isotherm analysis demonstrates that the pore structure of these mixes has been densified as evidenced by a reduction in intruded volume and a rise in BET surface area. Furthermore, both mixes had lower CO 2 -eq intensity per MPa as compared to control, which indicates their significant impact on producing green concretes through their reduced GWPs. Thus, this research shows that WSA alone or its blend with SF can be considered as a source of revenue for the concrete industry for developing high-performance and sustainable concretes.

The central aim of this study is to evaluate the effect of polyethylene terephthalate (PET) alongside two supplementary cementitious materials (SCMs)—i.e., fly ash (FA) and silica fume (SF)—on the 28-day compressive strength (CS28d) of cementitious grouts by using. For the gene expression programming (GEP) approach, a total of 156 samples were prepared in the laboratory using variable percentages of PET and SCM (0−10%, each). To achieve the best hyper parameter setting of the optimized GEP model, 10 trials were undertaken by varying the genetic parameters while observing the models’ performance in terms of statistical indices, i.e., correlation coefficient (R), root mean squared error (RMSE), mean absolute error (MAE), comparison of regression slopes, and predicted to experimental ratios (ρ). Sensitivity analysis and parametric study were performed on the best GEP model (obtained at; chromosomes = 50, head size = 9, and genes = 3) to evaluate the effect of contributing input parameters. The sensitivity analysis showed that: CS7d (30.47%) > CS1d (28.89%) > SCM (18.88%) > Flow (18.53%) > PET (3.23%). The finally selected GEP model exhibited optimal statistical indices (R = 0.977 and 0.975, RMSE = 2.423 and 2.531, MAE = 1.918 and 2.055) for training and validation datasets, respectively. The role of PET/SCM has no negative influence on the CS28d of cementitious grouts, which renders the PET a suitable alternative toward achieving sustainable and green concrete. Hence, the simple mathematical expression of GEP is efficacious, which leads to saving time and reducing labor costs of testing in civil engineering projects.

In this study, researchers examined the effect of replacing a high-volume of cement with sugarcane bagasse ash (BA) and silica fume (SF). In addition to the control, three binary and three ternary blends of concrete containing different percentages of cement/BA and cement/BA/SF were tested to determine the various mechanical and microstructural properties of concrete. For each mix, eighteen cylindrical concrete specimens were cast followed by standard curing (moist at 20 °C) to test the compressive and tensile strengths of three identical specimens at 7, 28, and 91 days. The test results indicated that the binary mix with 20% BA and ternary mix with 33% BA and 7% SF exhibited higher strengths than all the other mixes, including the control. The higher strengths of these mixes are also validated by their lower water absorption and apparent porosity than the other mixes. Following mechanical testing, the micro and pore structures of all mixes were investigated by performing scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM-EDS), Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and nitrogen (N 2 ) adsorption isotherm analysis. In SEM-EDS analysis, a dense and compact microstructure was observed for the BA20 and BA33SF7 mixtures due to the formation of high-density C-S-H and C-H phases. The formation of a large amount of C-S-H phases was observed through FTIR, where a prominent shift in peaks from 955 to 970 cm -1 was observed in the spectra of these mixes. Moreover, in N 2 adsorption isotherm analysis, a decrease in the intruded pore volume and an increase in the BET surface area of the paste matrix indicate the densification of the pore structure of these mixes. As observed through TGA, a reduction in the amount of the portlandite phase in these mixes leads to the formation of their more densified micro and pore structures. The current findings indicate that BA (20%) and its blend with SF (40%) represents a potential revenue stream for the development of sustainable and high-performance concretes in the future., (© 2022. The Author(s).)

Due to rise in infrastructure development and demand for seawater and sea sand concrete, fiber-reinforced polymer (FRP) rebars are widely used in the construction industry. Flexural strength is an important component of reinforced concrete structural design. Therefore, this research focuses on estimating the flexural capacity of FRP-reinforced concrete beams using novel artificial intelligence (AI) decision tree (DT) and gradient boosting tree (GBT) approaches. For this purpose, six input parameters, namely the area of bottom flexural reinforcement, depth of the beam, width of the beam, concrete compressive strength, the elastic modulus of FRP rebar, and the tensile strength of rebar at failure, are considered to predict the moment bearing capacity of the beam under bending loads. The models were trained using 60% of the database and were validated first-hand on the remaining 40% database employing the correlation coefficient (R), error indices namely, mean absolute error, root mean square error (MAE, RMSE) and slope of the regression line between observed and predicted results. The developed models were further validated using sensitivity and parametric analysis. Both models revealed comparable performance; however, based on the comparison of the slope of the validation data (0.83 for GBT model against 0.75 for the DT model) and higher R for the validation phase in case of the GBT model in comparison to the DT, the GBT model can be considered more accurate and robust. The sensitivity analysis yielded depth of the beam as the most influential parameter in contributing flexural strength of the beam, followed by the area of flexural reinforcement. The developed GBT model surpasses the existing gene expression programming (GEP) model in terms of accuracy; however, the current American Concrete Institute (ACI) model equations are more reliable than AI models in predicting the flexural strength of FRP-reinforced concrete beams.

The current biologically guided study aimed the in vitro investigation of cytotoxic activity, identification of the phytochemical content of Moluccella laevis L. aerial parts and supporting this activity by a molecular docking study. Aqueous fraction demonstrated the most potent cytotoxic effect against CACO-2 with IC 50  = 0.067 ± 0.01 μg/mL. Furthermore, EtOAc fraction showed a remarkable cytotoxic activity against MCF-7 cell line with IC 50  = 0.35 ± 0.02 μg/mL. Consequently, total ethanolic extract (TEE) and its fractions were subjected to LC-HR-ESI-MS metabolic profiling to discover the constituents that possibly underlie their cytotoxicity. Twenty compounds were tentatively identified from metabolic analysis. Furthermore, eight compounds were isolated. In silico docking study revealed that stachydrine is more likely to account for the antiproliferative activity of both EtOAc and aqueous fractions, probably via its moderate inhibition of receptor tyrosine kinases. [Formula: see text].

Background: Diabetes is a serious health problem that results in high mortality rates worldwide. α-defensins are antimicrobial peptides of the innate immune system that contribute to inflammation. However, data on serum levels of α-defensin in patients suffering from type 2 diabetes are limited., Objectives: This study aimed to assess the possible changes in α-defensin serum levels in patients suffering from type 2 diabetes and to investigate its correlation with relevant biomarkers., Methodology: Analysis of serum α-defensin levels in 47 type 2 diabetics with diabetic neuropathy, 19 type 2 diabetics with no complications and 19 healthy control subjects by enzyme-linked immunosorbent assay was established. Furthermore, measurement of advanced glycation end products (AGEs) and fasting blood glucose (FBG) serum levels was performed, together with the lipid profile analysis., Results: The serum levels of α-defensin were higher in patients with and without diabetic neuropathy in comparison to control subjects. In addition, there was a significant correlation between α-defensin serum levels and AGEs and FBG serum levels as well as with the body mass index., Conclusions: α-defensins are significantly elevated in serum of type II diabetics, and correlate with AGEs serum levels indicating a crosstalk that may aggravate inflammation in type 2 diabetes., (© 2022 El-Mowafy M et al.)