Search

Our previous study demonstrated that calcium-bonded titanium surface (Ca-Ti) can be obtained by hydrothermal reaction between titanium (Ti) and CaCl(2) and that bone-apatite like formation was observed after immersion in simulated body fluid. The purpose of the study was to determine the in vivo response to Ca-Ti surface using a rodent tibia model. Cylinders of commercially pure Ti were divided into three groups: (1) untreated group; (2) NaOH+hTi group: soaked in 5 mol/L NaOH solution at 60 degrees C then heated at 400 degrees C for 1 h; and (3) Ca-Ti group: hydrothermally treated in the presence of 10 mmol/L CaCl(2) at 200 degrees C for 24 h. The cylinders implanted in surgically created defects in tibias of 8-week old male Wistar rats were retrieved after 1, 2, and 4 weeks. Histomorphometric evaluations were made on stained decalcified thin sections. Results showed that at 1, 2, and 4 week after implantation, respectively, bone contact was 55.2 +/- 16.4%, 88.1 +/- 9.9%, and 96.1 +/- 4.8% for Ca-Ti implants, 5.7 +/- 5.3%, 19.9 +/- 1.2%, 57.4 +/- 4.8% for untreated; and 27.2 +/- 0.7%, 70.9 +/- 7.7%, and 96.0 +/- 5.1% for NaOH+hTi implants. These results suggest that hydrothermal treatment with CaCl(2) provides a bioactive Ca-Ti bonded surface that allows bone formation greater than that obtained with NaOH+heat treated Ti surfaces., (Copyright 2010 Wiley Periodicals, Inc. J Biomed Mater Res Part A, 2010.)

In this study, we investigated a novel method for fabrication of carbonate apatite block without ionic movement between precursor and solution by using precursor that includes all constituent ions of carbonate apatite. A powder mixture prepared from dicalcium phosphate anhydrous and calcite at appropriate Ca/P ratios (1.5, 1.67, and 1.8) was used as starting material. For preparation of specimens, the slurry made from the powder mixture and distilled water was packed in a split stainless steel mold and heat - treated, ranging from 60 degrees C to 100 degrees C up to 48 hours at 100% humidity. It appeared that carbonate apatite could be obtained above 70 degrees C and monophasic carbonate apatite could be obtained from the powder mixture at Ca/P ratio of 1.67. Carbonate content of the specimen was about 5-7%. Diametral tensile strength of the carbonate apatite blocks slightly decreased with increasing treatment temperature. The decrease in diametral tensile strength is thought to be related to the crystal size of the carbonate apatite formed.

Effects of sintering temperature on the physical and compositional properties of alpha-TCP foam fabricated using the polyurethane foam method were examined. When a polyurethane foam coated with alpha-TCP slurry was sintered at 1,400-1,550 degrees C, alpha-TCP foam having basically the same fully interconnected porous structure was produced although shrinkage occurred with increasing sintering temperature. On porosity of the alpha-TCP foam, a higher foam porosity of 95% was obtained when sintered at 1,400 degrees C as compared to the 90% porosity obtained at a higher sintering temperature of 1,550 degrees C. Further, at 1,500 degrees C or higher temperature, frame became dense with disappearance of micropores. On compressive strength, it increased from approximately 50 to 250 kPa when sintering temperature was increased from 1,400 to 1,550 degrees C. Nonetheless, no compositional changes were observed even when the alpha-TCP foam was cooled in the furnace without quenching process. In light of the results obtained, it was concluded that alpha-TCP foam fabricated using the polyurethane method was useful as a bone substitute and/or scaffolding material for tissue engineering. Besides, alpha-TCP foam could be useful as a precursor for the fabrication of other calcium phosphate foams.

Apatite cement containing porogen can be a useful material for the fabrication of biporous (macro- and microporous) apatite, which has gained much attention as a bone substitute material because of its large surface area and that it improves cell penetration. In the present study, the effects of added mannitol on the setting reaction and mechanical strength of apatite cement were evaluated. Apatite cements containing 0-40 wt% of mannitol were prepared and allowed to set in 0.9% saline kept at 37 degrees C for 1-7 days. Although the diametral tensile strength (DTS) value increased with time, it decreased with the amount of added mannitol. SEM observation and XRD analysis revealed that mannitol had no inhibitory effect on the transformation reaction of apatite cement to apatite. It was thus concluded that mannitol was a good candidate for the fabrication of biporous apatite because it is biocompatible, exhibits satisfactory dissolution behavior, and that it caused no inhibitory effects on the compositional transformation to apatitic material.

Transformation of gypsum model fabricated by three-dimensional printing (3DP) into hydroxyapatite (HA) by treating in ammonium phosphate solution is possible. However, 3DP powder supplied by the manufacturer contains unknown additives which may be questionable for biomaterials. Accordingly, pure plaster of Paris (POP) powder was used for fabrication in the present study. For accurate fabrication, reduction of supplied binder ink to 80% of standard amount for 3DP powder supplied by the manufacturer was found to be the optimal condition for POP fabrication. Transformation from POP to HA was done by immersing into 1 mol/L ammonium phosphate solution. However, preheating of fabricated POP specimen at 200 degrees C for 30 min to change from calcium sulfate dihydrate into calcium sulfate hemihydrate could accelerate the transformation into HA effectively. To increase compressive strength, HA transformed specimen was sintering at 1150 degrees C for 3 h. The compressive strength increased four times comparing with as transformed HA specimen. However, crystal structure was transformed to beta-TCP due to the chemical reaction between the transformed HA and remained phosphate from ammonium phosphate solution at the sintering temperature. A sophisticated application of the present 3DP method to fabricate the freeform bioceramic for osseous defect was attempted, and jaw bone defect filling biomaterial of beta-TCP and scaffold with macroporous structures could be fabricated. Present 3DP method has possibility to fabricate freeform bioceramic for osseous defect or scaffold.

Low-crystallinity hydroxyapatite (HAP) foam is an ideal material for bone substitutes and scaffolds for bone tissue regeneration, because its interconnected pores provide the space for cell growth and tissue penetration, and its composition induces excellent tissue response and good osteoconductivity. In this study, the feasibility of low-crystallinity HAP foam fabrication was evaluated based on the phase transformation reaction or the so-called dissolution-reprecipitation reaction of alpha-tricalcium phosphate (alpha-TCP) foam granules. When alpha-TCP foam granules were placed in water at 37 degrees C for 1 day, no reaction was observed. However, alpha-TCP foam granules set to form low-crystallinity HAP by treating it hydrothermally at 200 degrees C. The network of fully interconnected pores was retained, and porosity was as high as 82%. Pore size ranged from 50 to 300 mum with an average pore size of 160 mum. Compressive strength was 207 kPa. Although no setting reaction was observed at 37 degrees C, the setting reaction caused by the hydrothermal treatment of alpha-TCP foam granules allowed the fabrication of any shape of low-crystallinity HAP. Therefore, this method may be useful for the fabrication of bone substitutes and scaffolds in bone tissue regeneration., ((c) 2008 Wiley Periodicals, Inc.)

B-type carbonate apatite (CO3Ap) block may be an ideal artificial bone substitute because it is closer in chemical composition to bone mineral. In the present study, the feasibility to fabricate CO3Ap blocks was investigated using compositional transformation, which was based on the dissolution-precipitation reaction of a gypsum-calcite composite with free-molding behavior. For the compositional change, or phosphorization, gypsum-calcite composites of varying CaCO3 contents were immersed in 1 mol/L (NH4)3PO4 aqueous solution at 100 degrees C for 24 hours. No macroscopic changes were found after the treatment, whereas microscopic change was observed at SEM level. X-ray diffraction, Fourier transform infrared spectroscopy and CHN analysis indicated that the composites were B-type CO3Ap containing approximately 6-7 wt% of CO3, a value similar to that of biological bone apatite. Diametral tensile strength of the CO3Ap block was approximately 1-3 MPa. Based on the results obtained, it was therefore concluded that gypsum-calcite was a good candidate for the fabrication of CO3Ap blocks, coupled with the advantage that the composite can be molded to any shape by virtue of the setting property of gypsum.

Effects of liquid phase on the basic properties of alpha-tricalcuim phosphate (alpha-TCP)-based cement, BIOPEX, were investigated by employing three liquid phases: distilled water, neutral sodium hydrogen phosphate solution, and succinic acid disodium salt solution containing sodium salt of chondroitin sulfate. When mixed with neutral sodium hydrogen phosphate or succinic acid disodium salt solution, the initial setting times of the cement were 19.4 +/- 0.55 and 11.8 +/- 0.45 minutes respectively. These setting times were much shorter than that of distilled water, 88.4 +/- 0.55 minutes. Formation of needle-like crystals typical of apatite was much faster when neutral sodium hydrogen phosphate solution was used, as compared to distilled water or succinic acid disodium salt solution. Moreover, at 24 hours after mixing, the largest amount of apatite was formed when neutral sodium hydrogen phosphate solution was used, whereas use of succinic acid resulted in the least. On the final mechanical strength of the cement, that yielded with neutral sodium hydrogen phosphate solution was the highest. In contrast, lower mechanical strength was observed--especially at the initial stage--when succinic acid sodium salt was used. It was thus concluded that alpha-TCP-based cement allowed accelerated transformation to apatite, and that higher mechanical strength since the initial stage was achieved when neutral sodium hydrogen phosphate solution was used as the liquid phase.

The aims of this study were to evaluate the effects of CPP method on the crystallinity of apatite powder and on the acid resistance of bovine enamel. Crystallinity degrees of apatite powder before and after CPP treatment were measured by powder X-ray diffraction analysis. Polished bovine enamel specimens treated with CPP method or NaF were immersed in a lactic acid solution for up to five days. The demineralized depth of enamel was measured with a surface roughness analyzer. XRD peaks became sharper after the CPP treatment, indicating an increased crystallinity of the apatite powder. The demineralized depth of bovine enamel treated with CPP method was shallower than that of enamel treated with NaF. Results of this study revealed that the CPP method increased the crystallinity of apatite powder and the acid resistance of enamel. Therefore, the CPP method would be useful not only for treating dentin hypersensitivity, but also for the prevention of dental caries.

We have reported that low-crystalline porous calcite block, which is useful as a bone substitute or a source material to prepare apatite-type bone fillers could be fabricated by exposing calcium hydroxide compact to carbon dioxide gas saturated with water vapor. In the present study, we investigated the effect of molding pressure on the transformation of calcium hydroxide into calcite and the mechanical strength of the carbonated compact. Transformation into calcite was almost completed within 72 h, however, a small amount of Ca(OH)(2) still remained unreacted at higher molding pressure because of incomplete penetration of CO(2) gas into the interparticle space due to dense packing of Ca(OH)(2) particles. On the other hand, high molding pressure resulted in an increase in diametral tensile strength (DTS) of the calcite compact formed. Critical porosity of the calcite block was calculated as approximately 68%.

Calcium carbonate (CaCO(3)) has been widely used as a bone substitute material because of its excellent tissue response and good resorbability. In this experimental study, we propose a new method obtaining porous CaCO(3) monolith for an artificial bone substitute. In the method, calcium hydroxide compacts were exposed to carbon dioxide saturated with water vapor at room temperature. Carbonation completed within 3 days and calcite was the only product. The mechanical strength of CaCO(3) monolith increased with carbonation period and molding pressure. Development of mechanical strength proceeded through two steps; the first rapid increase by bonding with calcite layer formed at the surface of calcium hydroxide particles and the latter increase by the full conversion of calcium hydroxide to calcite. The latter process was thought to be controlled by the diffusion of CO(2) through micropores in the surface calcite layer. Porosity of calcite blocks thus prepared had 36.8-48.1% depending on molding pressure between 1 MPa and 5 MPa. We concluded that the present method may be useful for the preparation of bone substitutes or the preparation of source material for bone substitutes since this method succeeded in fabricating a low-crystalline, and thus a highly reactive, porous calcite block.

Effects of added alpha-tricalcium phosphate (alpha-TCP) and beta-TCP were investigated to shed light on the setting reaction of apatite cement (AC) consisting of tetracalcium phosphate (TTCP) and dicalcium phosphate anhydrous8 (DCPA). Added beta-TCP showed no reactivity, and thus resulted in extended setting time and decreased mechanical strength. In contrast, alpha-TCP dissolved to supply calcium and phosphate ions after initial apatite crystal formation by the reaction of TTCP and DCPA. Although setting time was delayed because alpha-TCP was involved only in the latter reaction of apatite cement, larger apatite crystals were formed due to its addition. As a result of larger apatite crystal formation, the mechanical strength of alpha-TCP-added apatite cement increased by approximately 30%, as compared to alpha-TCP-free apatite cement.

Three-dimensional printing (3DP) is a CAD/CAM built-up using ink-jet printing technique. Commercially available 3DP system can form only gypsum model and not for bioceramics. On the other hand, transformation of hardened gypsum into hydroxyapatite (HA) by treatment in ammonium phosphate solution was found lately. In the present study, transformation of the 3DP gypsum block to HA was attempted. However, the fabricated 3DP block was soluble in water. To insolubilize, it was heated at 300 degrees C for 10 min, and then, gypsum was transformed to calcium sulfate hemihydrate, CaSO(4) x 0.5H(2)O. The 3D block was immersed in 1M (NH(4))(3)PO(4) x 3H(2)O solution at 80 degrees C for 1-24 h, and the transformation into HA within 4 h was ascertained. A heat-treated plaster of Paris (POP) block was also investigated for comparison. The unheated POP block consisting of gypsum dihydrate took 24 h to complete the transformation, while the heat-treated POP consisting calcium sulfate hemihydrate promoted the transformation into HA; but the transformed thickness in the block was less than the 3DP block. This is probably due to higher solubility of the hemihydrate than gypsum dihydrate. Accelerated transformation of the 3DP block was also caused by its porous structure, which enabled an easy penetration of the phosphate solution. With the present method, it is possible to transform the fabricated gypsum by 3D printing that is adaptive to the osseous defect into HA prostheses or scaffold., ((c) 2006 Wiley Periodicals, Inc.)

The objective of this study was to investigate the regenerative effects of apatite foam (AF) combined with platelet-rich plasma (PRP) on bone defects. Critical-sized defects in the tibia of rats were filled with randomly distributed combinations of AF with and without PRP. The animals were killed after three, six, and 12 weeks, and their tissue responses were histologically examined. At three weeks, we found no significant differences in bone regeneration against control group (21.9 +/- 3.1%) when PRP (20.3 +/- 4.2%) and AF (21.6 +/- 2.9%) were used independently of each other. In contrast, significantly (p<0.01) larger amount of bone (32.3 +/- 6.5%) was formed when the defect was filled with PRP-incorporated AF. At six weeks, both PRP (38.1 +/- 3.2%) and AF (39.6 +/- 7.8%) showed significantly (p<0.05) higher rates of bone regeneration than the control, even though they were used independently. Moreover, the amount of regenerated bone significantly (p<0.01) increased in the defect filled with PRP-incorporated AF (76.1 +/- 8.2%). We concluded, therefore, that the combination of PRP and AF may be useful for the regeneration of defected bone.

Porous hydroxyapatite (HAP) foam permits three-dimensional (3D) structure with fully interconnecting pores as well as excellent tissue response and good osteoconductivity. It is therefore thought to be a good candidate as scaffold material for bone regeneration and as a synthetic bone substitute material. To fabricate better porous HAP foam, improved physical and structural properties as well as higher osteoconductivity are desired. In the present study, the effects of sintering temperature on the physical and compositional properties of porous HAP foam were evaluated by employing high sintering temperature starting at 1,300 degrees C up to 1,550 degrees C. The mechanical strength of porous HAP foam increased with sintering temperature to reach the maximum value at 1,525 degrees C, then decreased slightly when sintering temperature was further increased to 1,550 degrees C. Alpha tricalcium phosphate (alpha-TCP) was formed, and thus the porous HAP foam became biphasic calcium phosphate. Biphasic calcium phosphate consisting of both alpha-TCP and HAP had been reported to show higher osteoconductivity than HAP alone. We therefore recommend 1,500-1,550 degrees C as the sintering temperature for porous HAP foam since this condition provided the most desirable physical properties with biphasic calcium phosphate composition.

The corrosion behaviors of Ti, Ti-6Al-7Nb and Ti-6Al-4V alloys, and an experimentally produced Ti-0.5Pt alloy in 0.05% to 2.0% concentrations of Acidulated Phosphate Fluoride (APF) solutions (corresponding to 226 to 9,050 ppm fluoride at pH 3.5 or 3.6) were examined. While the corrosion of Ti, Ti-6Al-7Nb and Ti-6Al-4V alloys might occur easily even in a diluted 0.05% APF solution, dissolution of Ti from the Ti-0.5Pt alloy was observed only in test solutions with APF concentration exceeding 0.2%. When Ti-6Al-7Nb and Ti-6Al-4V alloys were immersed in 2.0% APF solution, their surfaces were entirely covered by compact corrosion products of Na3TiF6 due to severe corrosion. As a result, Ti dissolution was prevented and the amount of Ti dissolved decreased. However, since Ti was covered by porous, large-sized corrosion products of Na3TiF6 and that Ti-0.5Pt alloy was not covered with any corrosion product, the amount of Ti dissolved increased in the 2.0% APF solution.

In order to understand the requirements of guided bone regeneration (GBR) involving alginate base self-setting barrier membranes, GBR was performed in the case of bicortical bone defects formed at the tibiae of experimental animals employing self-setting and ready-made alginate membranes. Connective tissue ingress into the bone defects at the skin side of the tibia was observed when GBR was generated utilizing ready-made alginate membrane. In contrast, bone defects were reconstructed with bone tissue when GBR was generated with self-setting alginate membrane formed from aqueous 3% sodium alginate and 3% CaCl(2) solutions. The unreacted aqueous sodium alginate solution inherent to self-setting alginate membrane did not inhibit bone tissue regeneration. Rather, callus bone was formed using sodium alginate as the nucleus. However, when GBR was effected with self-setting alginate membrane formed from aqueous 10% CaCl(2) solution, membrane was too thick and thus regeneration of bone tissue in the bone cavity was prevented. Therefore, we concluded that self-setting alginate membrane is very useful as a barrier membrane for GBR upon appropriate adjustment of conditions with respect to preparation of alginate membrane.

Background: The aim of this in vivo study was to evaluate the effects of plaque control on the patency of dentinal tubules using vital teeth of beagle dogs., Methods: Class V cavities were prepared on the cervical areas of the mandibular and maxillary molars in each dog with a diamond point. To simulate the state of dentinal hypersensitivity, the teeth were etched with 50% citric acid for 2 minutes to obtain patent dentinal tubules. Plaque control was achieved by brushing the left-side teeth every day, whereas no plaque control was performed for the right-side teeth. A dentin biopsy was performed after 1, 2, and 3 weeks using the cylindrical diamond point to obtain dentin specimens., Results: In the plaque control group, some of the dentinal tubules were occluded with precipitate (Ca/P=1.49), and the diameter of the dentinal tubules decreased from 2.42+/-0.33 microm (mean+/-SD) to 1.11+/-0.51 microm after 7 days, although most of the dentinal tubules remained open. In contrast, no precipitate was observed in the dentinal tubules of the non-plaque control group. Also, the diameter of the dentinal tubules increased from 2.42+/-0.33 to 2.9+/-0.49 microm, due to the demineralization of the peritubular and intertubular dentin., Conclusion: Plaque control plays a key role in reducing the patency of dentinal tubules and, therefore, might promote the natural repair of dentinal hypersensitivity.

The aim of this study was to evaluate the feasibility of fabricating low-crystalline, porous apatite block using set gypsum as a precursor based on the fact that apatite is thermodynamically more stable than gypsum. When the set gypsum was immersed in 1 mol/L diammonium hydrogen phosphate aqueous solution at 100 degrees C, it transformed to low-crystalline porous apatite retaining its original shape. The transformation reaction caused a release of sulfate ions due to an ion exchange with phosphate ions, thus leading to a decrease in the pH of the solution. Then, due to decreased pH, dicalcium phosphate anhydrous--which has similar thermodynamic stability at lower pH--was also produced as a by-product. Apatite formed in the present method was low-crystalline, porous B-type carbonate apatite that contained approximately 0.5 wt% CO3, even though no carbonate sources--except carbon dioxide from air--were added to the reaction system. We concluded therefore that this is a useful bone filler fabrication method since B-type carbonate apatite is the biological apatite contained in bone.

The aim of this study was to evaluate the occluding ability of calcium phosphate precipitation (CPP) method and potassium oxalate treatment when each method was applied to dentin disks with different surface morphology. Occluding ability was observed by scanning electron microscopy. Irrespective of the diameter of the dentinal tubules, the CPP method showed a consistent occluding ability for dentinal tubules at the dentin surface, and that the depths of the precipitate formed in the dentinal tubules by CPP method were not significantly different. In contrast, the occluding ability of potassium oxalate treatment was reduced with increasing diameter of the dentinal tubules. However, the reduction of the occluding ability of potassium oxalate treatment was more markedly affected by the demineralization of dentin surface. Since the CPP method showed a consistent occluding ability irrespective of the diameter of the dentinal tubules, it is suggested that the CPP method would be a useful means for treating dentin hypersensitivity.

Effects of functionally gradient calcium phosphate consisting of hydroxyapatite (HAP) and alpha-tricalcium phosphate (alpha-TCP) on proliferation and differentiation of osteoblasts were evaluated using MC3T3-E1 cells. There were no significant differences in the proliferation of MC3T3-E1 cells among HAP-alpha-TCP functionally gradient calcium phosphate, pure HAP, and cell culture plastic wells. mRNA expressions of type I collagen, alkaline phosphate, and osteocalcine were evaluated as indexes of initial; mid-stage, and late-stage osteoblastic differentiation. Basically, HAP-alpha-TCP functionally gradient calcium phosphate and pure HAP enhanced the expressions of the three markers when compared with that of cell culture plastic wells. For type I collagen and alkaline phosphate expressions, HAP-alpha-TCP functionally gradient calcium phosphate showed the same expression level as pure HAP. For osteocalcine expression, HAP-alpha-TCP functionally gradient calcium phosphate showed a higher level than pure HAP. We concluded, therefore, HAP-alpha-TCP functionally gradient calcium phosphate has good potential to be a bone filler material with high osteoconductivity.

Effects of added sodium alginate on the mechanical strength of Biopex, one type of apatite cement, were investigated since sodium alginate addition is very effective for Biopex to acquire anti-washout property. Addition of sodium alginate into the liquid phase of Biopex resulted in a slower transformation to apatitic monolith. As a result, mechanical strength of set Biopex in terms of diametral tensile strength (DTS) decreased when it was hardened in an incubator kept at 37 degrees C and 100% relative humidity for 7 days. However, DTS value increased with increase in the amount of added sodium alginate when the Biopex paste was immersed in 0.9% saline at 37 degrees C for 7 days. Set Biopex with less sodium alginate also showed larger porosity. Based on these findings, we concluded that added sodium alginate was effective in increasing the mechanical strength of Biopex by inhibiting liquid penetration into its paste when it is exposed to body fluids.

It is well known that apatite cement causes inflammatory response if it is exposed to blood before setting. In this respect, the hemostatic procedure is very important. However, it has not been clarified how initial hemostasis affects the other basic properties of apatite cement. In the present study, the effect of initial hemostasis on the setting reaction was simulated by allowing the apatite cement paste to be hardened in an incubator for 1 to 30 minutes and then immersed in saline up to 7 days. We found faster transformation of apatite cement to apatitic mineral and higher mechanical strength of the set mass when the cement paste underwent a longer pre-hardening period. We also found that earlier exposure of apatite cement to saline resulted in a set mass with larger porosity. It is thought that the larger porosity of the cement is caused by the penetration of liquid into the cement paste, thus leading to lower mechanical strength and slower transformation of the apatite cement to apatitic mineral. We concluded, therefore, that hemostatic procedure is important not only to prevent inflammatory response but also to obtain a set mass with higher mechanical strength and faster transformation to apatitic mineral.

Sterilization capability is a necessary requirement for any material that is to be used in a medical application. Therefore, it is necessary for apatite cement (AC) to be sterilized. Because there is little information on the sterilization methods of AC, the aims of this investigation were to evaluate the effects of various sterilization methods, including steam, dry heat, ethylene oxide (EtO) gas, and gamma irradiation sterilizations, on the setting and mechanical properties of AC. In the case of steam sterilization, because AC powder aggregated before setting-time measurements, the setting time could not be measured. When the powder was sterilized by dry heat or EtO gas, the setting time was prolonged significantly and the wet diametral tensile strength (DTS) value decreased significantly. Therefore, sterilizations with steam, dry heat, or EtO gas were suggested to be inappropriate methods for AC. Accordingly, the following experiments focused on gamma sterilization. The setting time of AC was retarded with an increase in gamma irradiation dose. The wet DTS value decreased with the increase in gamma irradiation dose. There was no compositional change due to the gamma irradiation. The following tests were carried out in order to examine the effect of the gamma irradiation on the setting reaction of AC in detail. Tetracalcium phosphate [TTCP: Ca(4)(PO(4))(2)O] and dicalcium phosphate anhydrous (DCPA: CaHPO(4)) were separately irradiated, and the cements were produced with the use of irradiated powder and nonirradiated powder. Although the wet DTS value of AC produced from irradiated TTCP and nonirradiated DCPA decreased with increasing gamma irradiation dose, there was no significant difference. In contrast, the wet DTS value of AC produced from irradiated DCPA and nonirradiated TTCP significantly decreased with the increase in gamma irradiation dose. In conclusion, although the detailed mechanism of the delayed setting time and decreased DTS value was not clarified by the present study, it was found that gamma irradiation affected DCPA more than TTCP., (Copyright 2004 Wiley Periodicals, Inc.)

Hydroxyapatite (HAP) putty has been reported to have good hemostatic ability and excellent biocompatibility. Although the setting reaction of HAP putty and resulting transformation to HAP is the reason for this excellent biocompatibility, it also limits the handling period. In this study, the relationship between the setting reaction of HAP putty and its hemostatic ability was investigated, where neutral sodium hydrogen phosphate concentration and post-preparation time were used as indexes. A higher concentration of neutral sodium hydrogen phosphate was found to result in decreased hemostatic ability. The hemostatic ability of HAP putty decreased with time after its preparation; thus it was important to use HAP putty within 10 min after its preparation. The adhesive strength of HAP putty to bone increased with time. Therefore reliable hemostasis can be expected with HAP putty. Although the limited handling time is a drawback, HAP putty is thought to have a good potential as a hemostatic agent-it is highly reliable, and has a high hemostatic ability with excellent biocompatibility., (Copyright 2004 Wiley Periodicals, Inc.)

Biopex sets upon mixing with its liquid phase due to chelate reaction between sodium succinate and calcium phosphate, then gradually transforms to apatite. As a result of apatite formation, set Biopex shows excellent tissue responses and good osteoconductivity. However, Biopex would be washed out when the paste is exposed to body fluid before its setting reaction. Washed out cement causes an inflammatory response. In this investigation, therefore, sodium alginate was added to the liquid phase of Biopex and its effects on washout properties and transformation to apatite were studied. We found that cement remaining ratio, an index of the anti-washout property, of the Biopex increased by increasing the amounts of added sodium alginate to reach 100% when the liquid phase of Biopex contained 0.6% or more sodium alginate. Biopex gradually transformed to apatite regardless of the amount of added sodium alginate at least when the concentration of the sodium alginate in the liquid phase was 1.0% or less. It is concluded therefore, that addition of sodium alginate is very useful for Biopex to acquire the anti-washout property.

Alginate membrane is a new bioabsorbable, guided bone regeneration (GBR) membrane, which is placed directly on the surface of the bone defect. It is designed to drop a calcium chloride aqueous solution into the bone defect, which is filled with sodium alginate aqueous solution. Alginate membrane is an excellent agent for this procedure due to its close assimilation to the surface of the bone. In this study, we evaluated the short-term biocompatibility of alginate membrane in the bone defects of rat tibiae. GBR membrane availability was also examined. Consequently, we found that the healing process in bone defects covered with an alginate membrane was delayed in comparison with that of controls, however, the defect was restored to nearly original condition. In contrast, in the controls, bone defect repairs exhibited partitioning as a result of connective tissue involvement. Furthermore, we observed a relation between the sodium alginate concentration and the rate of absorption of the sodium alginate membrane. Absorption of a 1.5% sodium alginate membrane was slow. As a result, the compound was not absorbed completely and bone repairs resembled an hourglass. Moreover, the inflammatory response was absent surrounding the alginate membrane. The present findings suggested that the alginate membrane functions effectively as a GBR membrane. In addition, the alginate membrane derived from 3% calcium chloride and 1% sodium alginate was most suitable as a GBR membrane.

Objectives: The aim of this study was to evaluate the feasibility of regulation of NaF release from bis-GMA/TEGDMA resin using gamma-methacryloxypropyltrimethoxysilane (gamma-MPTS)., Methods: NaF powder was treated with gamma-MPTS to form a polysiloxane layer on its surface. The morphology and the composition of the NaF powder treated with gamma-MPTS were evaluated using scanning electron microscopy, infrared spectroscopy, contact angle measurement and X-ray photoelectron spectroscopy. Bis-GMA/TEGDMA resin containing 50 wt% NaF powder was prepared as a model resin and immersed in distilled water at 37 degrees C, and the amount of fluoride released from the resin was measured using a fluoride electrode. The mechanical strength in terms of diametral tensile strength before and after fluoride release was also measured, and statistically analyzed using one-way factorial ANOVA and Fisher's PLSD method., Results: NaF powder was covered with hydrophobic gamma-MPTS delivered polysiloxane. A larger amount of fluoride was released at the initial stage from the resin containing NaF treated with no gamma-MPTS. However, fluoride release terminated in a relatively shorter period. In contrast, we observed a smaller amount of fluoride released for a longer period from the resin containing NaF treated with gamma-MPTS., Significance: We found that gamma-MPTS treatment is useful for the regulation of NaF release from bis-GMA/TEGDMA resin. The mechanism of slow NaF release may be the formation of a hydrophobic polysiloxane layer on the surface of NaF powder and resulting slow water diffusion to NaF powder.

Although bone wax is known to cause an inflammatory reaction in soft tissue and a delay of bone healing, it is usually the first choice to arrest bleeding from bone. Hydroxyapatite (HAP) putty is proposed here. This study evaluated the feasibility of HAP putty with respect to whether or not it has potential value as a hemostatic agent for bone. First, the adhesive strength of HAP putty to bone was evaluated. The adhesive strength of HAP putty to wet bone was much higher when compared with that of bone wax, even though the adhesive strengths of HAP putty and bone wax to dry bone were equivalent. Next, to evaluate the hemostatic ability of HAP putty, bony defects were made in rabbits. HAP putty could arrest bleeding from bone within 3 min. However, when the hemostasis was performed with bone wax, bleeding was arrested within 8 min. Thus, HAP putty showed better hemostatic ability than bone wax. Finally, the tissue response to HAP putty in rabbit subcutaneous tissue was evaluated. Histological observation revealed a slight inflammatory response around HAP putty, whereas bone wax was surrounded by moderate inflammatory tissue. In conclusion, HAP putty has good potential value to be a hemostatic agent for bone because it has strong adhesion, good hemostatic ability, and biocompatibility., (Copyright 2002 Wiley Periodicals, Inc. J Biomed Mater Res (Appl Biomater) 63: 542-547, 2002)

Recently, the effects of Zn2+ on osteogenesis stimulation have become major topics in the research fields of bone formation and organism essential elements. Based on the fundamental finding of Zn2+ with respect to osteogenesis stimulation, Ito et al. have prepared Zn doped beta-tricalcium phosphate (ZnTCP) and have reported that ZnTCP enhances the proliferation of MC3T3-E1 cells. In this investigation, we studied the effects of ZnTCP added to apatite cement (AC) with respect to its setting reaction and proliferation of human osteoblastic cells as an initial evaluation for the feasibility of AC containing ZnTCP. Compositional analysis using powder X-ray diffractometer revealed that ZnTCP shows no reactivity with the setting reaction of AC. As a result, the mechanical strength of set AC decreased increasing amounts of added ZnTCP as if ZnTCP acts as a pore in AC. The setting time of AC was not affected by addition of ZnTCP up to 10%. When AC containing ZnTCP was immersed in alpha-MEM containing 10% bovine serum, Zn2+ was released from AC. Larger amounts of Zn2+ were released from AC containing larger amounts of ZnTCP. When human osteoblastic cells were incubated on the surface of AC discs, proliferation of human osteoblastic cells was significantly increased on the surface of AC that contained 5% ZnTCP when compared with that containing no ZnTCP. In contrast, proliferation of human osteoblastic cells decreased on the surface of AC that contained 10% ZnTCP when compared with that free from ZnTCP; indicating cytotoxicity. We concluded therefore, that addition of ZnTCP to AC is useful to enhance the osteoconductivity of AC when release of Zn2+ can be carefully regulated.