Search

Background: Total knee arthroplasty and its relation to gait abduction or adduction moment has not been fully described., Methods: Gait analysis was performed on 25 patients (27 knees) preoperatively, 6 months and 1 year after total knee arthroplasty. Reflective markers were placed on the lower extremity, and motion data were collected at 60 Hz using 6 infrared cameras. Ground reaction forces were recorded at 960 Hz with a force plate. Stance phase was divided into braking and propulsive phases. Coronal knee angles and moments were calculated. Repeated-measures analysis of variance was used to compare frontal plane knee impulse over time and between the braking and propulsive phases of stance., Results: In varus knees, static alignment was corrected from 2.2° varus to 3.3° valgus and in valgus knees from 15.2° valgus to 2.7° valgus (P < .010). Braking phase adduction impulse decreased from 0.145 to 0.111 at 6 months but increased to 0.126 Nm/kg s (P > .05) at 1 year. Propulsive phase impulse changed from 0.129 to 0.085 and persisted at 1 year. Impulse changed from 0.01 (abduction) to 0.11 Nm/kg s (adduction) at 6 months and persisted (P = .01)., Conclusion: Restoration of anatomic alignment and soft tissue balancing changes the lateral loading conditions of valgus knees. Both cases, between 6 months and 1 year, increased peak moment., (Copyright © 2016 Elsevier Inc. All rights reserved.)

Objective: The aim of this study is to assess the effect of 5 and 10° lateral-wedge insoles on unilateral lower extremity load carrying line in patients with medial knee osteoarthritis using the L.A.S.A.R. posture alignment system., Patients and Methods: Twenty subjects (10 females and 10 males, mean age 67.7 ± 5.4 years (range: 58-78) with bilateral medial knee osteoarthritis were included in the study. The laser line projected on the person by the L.A.S.A.R. posture alignment system showed joint load carrying line. The location of the joint load carrying line in static standing with one foot on the force plate was assessed with barefoot, and 5° and 10° lateral-wedge insoles. Displacement of the load carrying line was measured using a ruler placed tangentially to the patella at the level of joint line., Results: The load carrying lines measured with 5° and 10° lateral-wedge insoles were significantly laterally located compared to that without wearing insole (p < 0.001). 10° lateral-wedge insole caused a significant more lateral shifting of the load carrying line than 5° lateral-wedge insole (p < 0.001)., Conclusion: Both wedge insoles was effective in moving of the unilateral lower extremity load carrying line to the lateral. Lateral wedged insoles are biomechanically effective and reduce loading of the medial compartment in patients with medial knee osteoarthritis., (Copyright © 2016 Turkish Association of Orthopaedics and Traumatology. Production and hosting by Elsevier B.V. All rights reserved.)

Purpose: The purpose of this study was to evaluate the influence of immersion in a virtual reality environment on knee biomechanics in patients after ACL reconstruction (ACLR). It was hypothesized that virtual reality techniques aimed to change attentional focus would influence altered knee flexion angle, knee extension moment and peak vertical ground reaction force (vGRF) in patients following ACLR., Methods: Twenty athletes following ACLR and 20 healthy controls (CTRL) performed a step-down task in both a non-virtual reality environment and a virtual reality environment displaying a pedestrian traffic scene. A motion analysis system and force plates were used to measure kinematics and kinetics during a step-down task to analyse each single-leg landing., Results: A significant main effect was found for environment for knee flexion excursion (P = n.s.). Significant interaction differences were found between environment and groups for vGRF (P = 0.004), knee moment (P < 0.001), knee angle at peak vGRF (P = 0.01) and knee flexion excursion (P = 0.03). There was larger effect of virtual reality environment on knee biomechanics in patients after ACLR compared with controls., Conclusion: Patients after ACLR immersed in virtual reality environment demonstrated knee joint biomechanics that approximate those of CTRL. The results of this study indicate that a realistic virtual reality scenario may distract patients after ACLR from conscious motor control. Application of clinically available technology may aid in current rehabilitation programmes to target altered movement patterns after ACLR., Level of Evidence: Diagnostic study, Level III.

Mechanical evaluation of total knees is frequently required for aspects such as wear, strength, kinematics, contact areas, and force transmission. In order to carry out such tests, we developed a crouching simulator, based on the Oxford-type machine, with novel features including a synthetic knee including ligaments. The instrumentation and data processing methods enabled the determination of contact area locations and interface forces and moments, for a full flexion-extension cycle. To demonstrate the use of the simulator, we carried out a comparison of two different total knee designs, cruciate retaining and substituting. The first part of the study describes the simulator design and the methodology for testing the knees without requiring cadaveric knee specimens. The degrees of freedom of the anatomic hip and ankle joints were reproduced. Flexion-extension was obtained by changing quadriceps length, while variable hamstring forces were applied using springs. The knee joint was represented by three-dimensional printed blocks on to which the total knee components were fixed. Pretensioned elastomeric bands of realistic stiffnesses passed through holes in the block at anatomical locations to represent ligaments. Motion capture of the knees during flexion, together with laser scanning and computer modeling, was used to reconstruct contact areas on the bearing surfaces. A method was also developed for measuring tibial component interface forces and moments as a comparative assessment of fixation. The method involved interposing Tekscan pads at locations on the interface. Overall, the crouching machine and the methodology could be used for many different mechanical measurements of total knee designs, adapted especially for comparative or parametric studies., (© IMechE 2016.)

The computational modeling approach has commonly been used to predict knee joint contact forces, muscle forces, and ligament loads during activities of daily living. Knowledge of these forces has several potential applications, for example, within design of equipment to protect the knee joint from injury and to plan adequate rehabilitation protocols, although clinical applications of computational models are still evolving and one of the limiting factors is model validation. The objective of this study was to extend previous modeling technique and to improve the validity of the model prediction using publicly available data set of the fifth "Grand Challenge Competition to Predict In Vivo Knee Loads." A two-stage modeling approach, which combines conventional inverse dynamic analysis (the first stage) with a multi-body subject-specific lower limb model (the second stage), was used to calculate medial and lateral compartment contact forces. The validation was performed by direct comparison of model predictions and experimental measurement of medial and lateral compartment contact forces during normal and turning gait. The model predictions of both medial and lateral contact forces showed strong correlations with experimental measurements in normal gait (r = 0.75 and 0.71) and in turning gait trials (r = 0.86 and 0.72), even though the current technique over-estimated medial compartment contact forces in swing phase. The correlation coefficient, Sprague and Geers metrics, and root mean squared error indicated that the lateral contact forces were predicted better than medial contact forces in comparison with the experimental measurements during both normal and turning gait trials., (© IMechE 2016.)

Background: Horizontal, degenerative tears of the medial meniscus and subsequent meniscectomy can compromise the biomechanical function of the meniscus in load transmission and weightbearing, leading to the development of radiographic and symptomatic tibiofemoral arthritis., Hypothesis: Resection of both leaflets of a horizontal medial meniscal tear will increase peak contact pressures and decrease contact areas in comparison with resection of only the inferior leaflet., Study Design: Controlled laboratory study., Methods: Twelve fresh-frozen human cadaveric knees had tibiofemoral peak contact pressures and contact areas under an 1800-N axial load measured by Tekscan in the control state. A horizontal tear was created in the posterior horn of the medial meniscus, and the knees were retested. The knees were tested a third time after resection of the inferior leaflet (single leaflet) and a final time after resection of the superior leaflet (both leaflets). The Friedman test was used to test for group differences in peak pressure (psi) and contact area (mm(2)) between test conditions (native, tear, inferior leaflet resection, and resection of both leaflets)., Results: For the medial compartment, there was a statistically significant difference in peak pressure (P = .03) but not in contact area (P = .70) between testing conditions. Median peak pressure in the medial compartment was significantly greater for resection of both leaflets compared with the tear (406.5 vs 294.7 psi, respectively; P = .002). Median contact area in the medial compartment was greatest for resection of both leaflets (602.7 mm(2)), but there were no statistically significant differences between test conditions (P = .70). For the lateral compartment, there were no statistically significant differences in peak pressure (P = .99) or contact area (P = .77) between test conditions., Conclusion: Resection of a single inferior leaflet after a horizontal medial meniscal tear preserves much of the original biomechanical function of the meniscus. Resection of both leaflets leads to a significant increase in contact pressure dispersed over the same contact area, which results in an undesirable biomechanical environment., Clinical Relevance: Arthroscopic inferior leaflet resection is a viable option for providing symptomatic relief of horizontal medial meniscal tears and preserves the ability of the meniscus to absorb axial loading on the knee joint, theoretically decreasing the risk of subsequent osteoarthritis., (© 2016 The Author(s).)

When considering knee pain in runners, clinicians differentiate sources of symptoms and determine their cause. Knee problems arise when a runner increases the amount/frequency of the loading through the lower limb. The way the loading is distributed through the knee determines which tissues are abnormally loaded. Knee problems cannot be considered in isolation, requiring a thorough investigation of static and dynamic lower limb mechanics, and footwear and surfaces. This article examines potential sources of knee pain and explores the role of the infrapatellar fat pad and synovial plica in the mechanics of the knee and its involvement in knee symptoms., (Copyright © 2016 Elsevier Inc. All rights reserved.)

Background: Patients following meniscectomy are at increased risk of developing knee osteoarthritis in the tibiofemoral compartment and at the patellofemoral joint. As osteoarthritis is widely considered a mechanical disease, it is important to understand the potential effect of arthroscopic partial meniscectomy (APM) on knee joint mechanics. The purpose of this study was to evaluate changes in knee joint biomechanics during a forward lunge in patients with a suspected degenerative meniscal tear from before to three months after APM., Methods: Twenty-two patients (35-55 years old) with a suspected degenerative medial meniscal tear participated in this study. Three dimensional knee biomechanics were assessed on the injured and contralateral leg before and three months after APM. The visual analogue scale was used to assess knee pain and the Knee Injury Osteoarthritis Outcome Score was used to assess sport/recreation function and knee-related confidence before and after APM., Results: The external peak knee flexion moment reduced in the APM leg compared to the contralateral leg (mean difference (95% CI)) -1.08 (-1.80 to -0.35) (Nm/(BW × HT)%), p = 0.004. Peak knee flexion angle also reduced in the APM leg compared to the contralateral leg -3.94 (-6.27 to -1.60) degrees, p = 0.001. There was no change in knee pain between the APM leg and contralateral leg (p=0.118). Self-reported sport/recreation function improved (p = 0.004)., Conclusions: Although patients self-reported less difficulty during strenuous tasks following APM, patients used less knee flexion, a strategy that may limit excessive patellar loads during forward lunge in the recently operated leg., (Copyright © 2015 Elsevier B.V. All rights reserved.)

Background: ACL injuries are common in sports, which has resulted in the development of risk screening and injury prevention programs to target modifiable neuromuscular risk factors. Previous studies which have analyzed single-leg cutting tasks have reported that the anticipation status of the task (pre-planned vs. unanticipated) has a significant effect on the mechanics of the knee., Hypothesis/purpose: The purpose of this systematic review is to assess the effect of anticipation on the mechanics of the knee in the sagittal, frontal, and transverse planes during tasks which athletes frequently perform during competition., Study Design: Systematic Review., Methods: The following databases were searched using relevant key words and search limits: Pub Med, SPORTDiscus, CINAHL, and Web of Science. A modified version of the Downs and Black checklist was used to assess the methodological quality of the articles by two independent reviewers., Results: 284 articles were identified during the initial database search. After a screening process, 34 articles underwent further review. Of these articles, 13 met the criteria for inclusion in this systematic review., Conclusions: It appears that tasks which do not allow a subject to pre-plan their movement strategy promote knee mechanics which may increase an athlete's risk of injury., Clinical Relevance: Clinicians involved in the development and implementation of ACL injury risk screening and prevention programs may want to consider incorporating tasks which do not allow time for pre-planning. These unanticipated tasks may more closely mimic the demands of the sports environment and may promote mechanics which increase the risk of injury., Level of Evidence: Level 1b.

Background: It has been reported that over 70% of anterior cruciate ligament (ACL) injuries occur in noncontact situations and that females are at 2 to 8 times greater risk of ACL injury than males. Increased joint laxity and reduced knee stiffness in female knees have been suggested as possible explanations for the higher ACL injury rates in females., Hypothesis: Compared with male knees, female knees will demonstrate increased laxity and reduced stiffness along the anterior-posterior (AP), internal-external (IE), and varus-valgus (VV) directions., Study Design: Controlled laboratory study., Methods: Forty-seven fresh-frozen human cadaveric knees were tested (22 male and 25 female) by use of a robotic system. Mean ages were 34.6 years (range, 19-45 years) for males and 28.4 years (range, 16-42 years) for females. Joint laxity and stiffness were measured from force-vs-displacement or torque-vs-rotation curves recorded for 3 modes of testing: ± 134 N AP force, ± 5 N · m IE torque, and ± 10 N · m VV moment., Results: Compared with male knees, female knees had greater internal laxity from 0° to 50° flexion (P < .01; maximum difference of 8.3° at 50° of flexion) and greater valgus laxity from 0° to 50° of flexion (P < .05; maximum difference of 1.6° at 50° of flexion). However, female knees exhibited greater anterior laxity only at 50° of flexion (P < .03; difference of 1.3 mm). No significant male-female differences in anterior or posterior stiffness were found. Male knees had 42% greater internal stiffness from 0° to 30° of flexion (P < .03), 35% greater valgus stiffness at 10° of flexion (P < .03), and 19% greater varus stiffness at 50° of flexion (P < .03)., Conclusion: Female knees demonstrated significantly increased laxity and reduced stiffness compared with males. This finding was not uniform but was dependent on the direction tested and the knee flexion angle., Clinical Relevance: Understanding the risk factors for noncontact ACL injury is important for injury prevention. In combination with other female-specific risk factors, increased knee laxity may be a contributing factor associated with the higher rate of female ACL injuries., (© 2015 The Author(s).)

Background: Simple observational assessment of movement is a potentially low-cost method for anterior cruciate ligament (ACL) injury screening and prevention. Although many individuals utilize some form of observational assessment of movement, there are currently no substantial data on group skill differences in observational screening of ACL injury risk., Purpose/hypothesis: The purpose of this study was to compare various groups' abilities to visually assess ACL injury risk as well as the associated strategies and ACL knowledge levels. The hypothesis was that sports medicine professionals would perform better than coaches and exercise science academics/students and that these subgroups would all perform better than parents and other general population members., Study Design: Cross-sectional study; Level of evidence, 3., Methods: A total of 428 individuals, including physicians, physical therapists, athletic trainers, strength and conditioning coaches, exercise science researchers/students, athletes, parents, and members of the general public participated in the study. Participants completed the ACL Injury Risk Estimation Quiz (ACL-IQ) and answered questions related to assessment strategy and ACL knowledge., Results: Strength and conditioning coaches, athletic trainers, physical therapists, and exercise science students exhibited consistently superior ACL injury risk estimation ability (+2 SD) as compared with sport coaches, parents of athletes, and members of the general public. The performance of a substantial number of individuals in the exercise sciences/sports medicines (approximately 40%) was similar to or exceeded clinical instrument-based biomechanical assessment methods (eg, ACL nomogram). Parents, sport coaches, and the general public had lower ACL-IQ, likely due to their lower ACL knowledge and to rating the importance of knee/thigh motion lower and weight and jump height higher., Conclusion: Substantial cross-professional/group differences in visual ACL injury risk estimation exist. The relatively profound differences in injury risk estimation accuracy and their potential implications for risk screening suggest the need for additional training and outreach (see http://www.ACL-IQ.org)., Clinical Relevance: Parents and sport coaches would likely benefit from training or use of decision support tools such as the ACL nomogram to assess ACL injury risk. In addition, physicians and other sports medicine professionals may also benefit from improving risk estimation performance to reach clinical biomechanical standards.

Background: Persistent rotatory instability after anterior cruciate ligament (ACL) reconstruction may be a result of unaddressed insufficiency of the anterolateral structures. Recent publications about the anatomy of the anterolateral ligament (ALL) have led to a renewed interest in lateral extra-articular procedures, and several authors have proposed ALL reconstruction to supplement intra-articular ACL reconstruction. However, only limited knowledge about the biomechanical characteristics of the ALL exists., Purpose/hypothesis: The purpose of this study was to analyze length changes of the ALL during passive knee motion. The study hypothesis was that the ALL lengthens with knee flexion and internal tibial rotation., Study Design: Controlled laboratory study., Methods: The ALL of 6 cadaveric knees was dissected. Specimens were mounted in a specifically designed test rig that allowed unconstrained passive flexion/extension movement between 0° and 90° as well as external/internal tibial rotation of 25° at various flexion angles. Highly elastic, capacitive polydimethylsiloxane strain gauges were attached to the insertion sites of the ALL. Length changes were recorded continuously at flexion angles between 0° and 90° and during internal/external tibial rotation at 0°, 15°, 30°, 45°, 60°, 75°, and 90°. All measurements were calculated as the relative length change (%) of the ALL compared with 0° of flexion and neutral rotation., Results: The mean relative length of the ALL significantly increased with increasing knee flexion (P < .001), with an estimated mean length change of +0.15% per degree. Both internal and external tibial rotation were independent determinants for length change; internal rotation significantly increased the length of the ALL (P < .001), whereas external rotation significantly decreased its length (P < .001). The mean length change with internal rotation increased with knee flexion, with a significantly greater length change at 90° compared with 0° (P = .048), 15° (P = .033), and 30° (P = .015). The maximum mean length change was +33.77% ± 9.62%, which was observed at 25° of internal rotation and 90° of flexion., Conclusion: The ALL is a nonisometric structure that tensions with knee flexion and internal tibial rotation. Length changes with internal rotation were greater at higher flexion angles, with the greatest length change of the ALL observed at 90° of flexion., Clinical Relevance: The ALL can be considered a stabilizer against internal tibial rotation, especially at deep flexion angles. With regard to ALL reconstruction procedures, tensioning and fixation of the graft should be performed near 90° of flexion because graft tensioning near extension may cause excessive ligament strain with increasing knee flexion., (© 2015 The Author(s).)

Six degree of freedom (6-DOF) robotic manipulators have simulated clinical tests and gait on cadaveric knees to examine knee biomechanics. However, these activities do not necessarily emulate the kinematics and kinetics that lead to anterior cruciate ligament (ACL) rupture. The purpose of this study was to determine the techniques needed to derive reproducible, in vitro simulations from in vivo skin-marker kinematics recorded during simulated athletic tasks. Input of raw, in vivo, skin-marker-derived motion capture kinematics consistently resulted in specimen failure. The protocol described in this study developed an in-depth methodology to adapt in vivo kinematic recordings into 6-DOF knee motion simulations for drop vertical jumps and sidestep cutting. Our simulation method repeatably produced kinetics consistent with vertical ground reaction patterns while preserving specimen integrity. Athletic task simulation represents an advancement that allows investigators to examine ACL-intact and graft biomechanics during motions that generate greater kinetics, and the athletic tasks are more representative of documented cases of ligament rupture. Establishment of baseline functional mechanics within the knee joint during athletic tasks will serve to advance the prevention, repair and rehabilitation of ACL injuries.

Combining accurate bone kinematics data from biplane radiography with cartilage models from magnetic resonance imaging, it is possible to estimate tibiofemoral cartilage contact area and centroid location. Proper validation of such estimates, however, has not been performed under loading conditions approximating functional tasks, such as gait, squatting, and stair descent. The goal of this study was to perform an in vitro validation to resolve the accuracy of cartilage contact estimations in comparison to a laser scanning gold standard. Results demonstrated acceptable reliability and accuracy for both contact area and centroid location estimates. Root mean square errors in contact area averaged 8.4% and 4.4% of the medial and lateral compartmental areas, respectively. Modified Sorensen-Dice agreement scores of contact regions averaged 0.81 ± 0.07 for medial and 0.83 ± 0.07 for lateral compartments. These validated methods have applications for in vivo assessment of a variety of patient populations and physical activities, and may lead to greater understanding of the relationships between knee cartilage function, effects of joint injury and treatment, and the development of osteoarthritis., (Copyright © 2015 IPEM. Published by Elsevier Ltd. All rights reserved.)

Background: A smaller knee flexion angle and larger knee valgus angle during weight-bearing activities have been identified as risk factors for non-contact anterior cruciate ligament (ACL) injuries. To prevent such injuries, attention has been focused on the role of hip strength in knee motion control. However, gender differences in the relationship between hip strength and knee kinematics during weight-bearing activities in the frontal plane have not been evaluated., Hypothesis/purpose: The purpose of this study was to determine the influence of hip strength on knee kinematics in both genders during a single-legged landing task in the frontal plane. The hypotheses were that 1) subjects with a greater hip strength would demonstrate larger knee flexion and smaller knee valgus and internal rotation angles and 2) no gender differences would exist during the single-legged landing task., Methods: Forty-three Japanese collegiate basketball players (20 males, 23 females) participated in this study. Three-dimensional motion analysis was used to evaluate knee kinematics during a single-legged medial drop landing (SML). A hand-held dynamometer was used to assess hip extensor (HEXT), abductor (HAB), and external rotator (in two positions: seated position [SHER] and prone [PHER]) isometric strength. Spearman rank correlation coefficients (ρ) were determined for correlations between hip strength and knee kinematics at initial contact (IC) and peak (PK) during SML (p < 0.05)., Results: Negative correlations were observed between the knee valgus angle at IC and HEXT (ρ = -0.48, p = 0.02), HAB (ρ = -0.46, p = 0.03) and PHER (ρ = -0.44, p = 0.04) strength in females. In addition, a significant positive correlation was observed between the knee flexion angle at PK and HEXT strength (ρ = 0.61, p = 0.004) in males., Conclusions: Significant correlations between hip strength and knee kinematics during SML were observed in both genders. Hip strength may, therefore, play an important role in knee motion control during sports activities, suggesting that increased hip strength may help to prevent non-contact ACL injuries in athletes of both genders. Moreover, gender-specific programs may be needed to control abnormal knee motion, as the influence of hip strength on knee kinematics may differ based on gender., Level of Evidence: 3.

Background: The medial collateral (MCL) and anterior cruciate ligaments (ACL) are, respectively, the primary and secondary ligamentous restraints against knee abduction, which is a component of the valgus collapse often associated with ACL rupture during athletic tasks. Despite this correlation in function, MCL ruptures occur concomitantly in only 20% to 40% of ACL injuries., Hypothesis/purpose: The purpose of this investigation was to determine how athletic tasks load the knee joint in a manner that could lead to ACL failure without concomitant MCL failure. It was hypothesized that (1) the ACL would provide greater overall contribution to intact knee forces than the MCL during simulated motion tasks and (2) the ACL would show greater relative peak strain compared with the MCL during simulated motion tasks., Study Design: Controlled laboratory study., Methods: A 6-degrees-of-freedom robotic manipulator articulated 18 cadaveric knees through simulations of kinematics recorded from in vivo drop vertical jump and sidestep cutting tasks. Specimens were articulated in the intact-knee and isolated-ligament conditions. After simulation, each ACL and MCL was failed in uniaxial tension along its fiber orientations., Results: During a drop vertical jump simulation, the ACL experienced greater peak strain than the MCL (6.1% vs 0.4%; P < .01). The isolated ACL expressed greater peak anterior force (4.8% vs 0.3% body weight; P < .01), medial force (1.6% vs 0.4% body weight; P < .01), flexion torque (8.4 vs 0.4 N·m; P < .01), abduction torque (2.6 vs 0.3 N·m; P < .01), and adduction torque (0.5 vs 0.0 N·m; P = .03) than the isolated MCL. During failure testing, ACL specimens preferentially loaded in the anteromedial bundle failed at 637 N, while MCL failure occurred at 776 N., Conclusion: During controlled physiologic athletic tasks, the ACL provides greater contributions to knee restraint than the MCL, which is generally unstrained and minimally loaded., Clinical Relevance: Current findings support that multiplanar loading during athletic tasks preferentially loads the ACL over the MCL, leaving the ACL more susceptible to injury. An enhanced understanding of joint loading during in vivo tasks may provide insight that enhances the efficacy of injury prevention protocols., (© 2015 The Author(s).)

Background: The pivot-shift (PS) examination is used to demonstrate knee instability and detect anterior cruciate ligament (ACL) injury. Prior studies using inertial sensors identified the ACL-deficient knee with reasonable accuracy, but none addressed the more difficult problem of using these sensors to determine whether a subject has an ACL deficiency and to correctly assign a PS grade to a patient's knee., Hypothesis: Inertial sensor data recorded during a PS examination can accurately predict ACL deficiency and the PS score assigned by the examining physician., Study Design: Cohort study (diagnosis); Level of evidence, 2., Methods: A total of 32 patients with unilateral ACL deficiency and 29 with intact ACLs in both knees had inertial sensor modules strapped to the tibia and femur of each limb for preoperative PS testing under anesthesia. Support vector machine (SVM) methods assessed PS grades on the basis of these data, with the examiner's clinical grading shift used as ground truth. A fusion of regression and SVM classification techniques diagnosed ACL deficiency., Results: The clinically determined PS grades of all 122 knees were as follows: 0 (n = 69), +1 (n = 23), +2 (n = 27), and +3 (n = 3). The SVM classification analysis was 77% accurate in correctly classifying these grades, with 98% of computed PS grades falling within ±1 grade of the clinically determined value. The system fusion algorithm diagnosed ACL deficiency in an individual with an overall accuracy of 97%. This method yielded 6% false negatives and 0% false positives., Conclusion: This study used inertial sensor technology with SVM algorithms to accurately determine clinically assigned PS grades in ACL-intact and ACL-deficient knees. By extending the assessment to a separate group of patients without ACL injury, the inertial sensor data demonstrated highly accurate diagnosis of ACL deficiency., (© 2015 The Author(s).)

The knee joint is one of the most common sites for osteoarthritis, the onset and progression of which are believed to relate to the mechanical environment of cartilage. To understand this environment, it is necessary to take into account the complex biphasic contact interactions of the cartilage and menisci. In this study, the time-dependent contact behaviour of an intact and a meniscectomized human tibiofemoral joint was characterized under body weight using a computational model. Good agreement in the contact area and femoral displacement under static loads were found between model predictions of this study and published experimental measurements. The time-dependent results indicated that as loading time progressed, the contact area and femoral vertical displacement of both intact and meniscectomized joints increased. More load was transferred to the cartilage-cartilage interface over time. However, the portions of load borne by the lateral and medial compartments did not greatly vary with time. Additionally, during the whole simulation period, the maximum compressive stress in the meniscectomized joint was higher than that in the intact joint. The fluid pressure in the intact and meniscectomized joints remained remarkably high at the condyle centres, but the fluid pressure at the cartilage-meniscus interface decreased faster than that at the condyle centres as loading time progressed. The above findings provide further insights into the mechanical environment of the cartilage and meniscus within the human knee joint., (© IMechE 2014.)

To investigate the biomechanical effect of skeletal knee joint abnormalities, the authors propose to implant pathologically shaped rapid prototyped implants in cadaver knee specimens. This new method was validated by replacing the native trochlea by a replica implant on four cadaver knees with the aid of cadaver-specific guiding instruments. The accuracy of the guiding instruments was assessed by measuring the rotational errors of the cutting planes (on average 3.01° in extension and 1.18° in external/internal rotation). During a squat and open chain simulation, the patella showed small differences in its articulation with the native trochlea and the replica trochlea, which could partially be explained by the rotational errors of the implants. This study concludes that this method is valid to investigate the effect of knee joint abnormalities with a replica implant as a control condition to account for the influence of material properties and rotational errors of the implant., (© IMechE 2014.)

Background: Lateral meniscal tears are often seen with acute anterior cruciate ligament (ACL) injury and may be left in situ, repaired, or treated with meniscectomy. Clinical studies have shown good outcomes with vertical tears left in situ and poor outcomes following meniscectomy. However, clinically relevant studies are needed to establish a biomechanical foundation for treatment of these tears, particularly regarding the effects of meniscectomy., Purpose: To compare tibiofemoral joint mechanics following vertical lateral meniscal tears and meniscectomies. We hypothesized that a peripheral vertical tear of the lateral meniscus would alter joint mechanics, increasing contact pressure and area, and that more drastic effects would be seen following meniscectomy, at higher knee flexion angles, and with increased loads., Study Design: Controlled laboratory study., Methods: Ten fresh-frozen cadaveric knees (average age, 55 ± 12 years) were tested with 5 lateral meniscus states: intact, short vertical tear, extended vertical tear, posterior horn partial meniscectomy (rim intact), and posterior horn subtotal meniscectomy (rim excised). The specimens were loaded axially at knee flexion angles of 0°, 30°, and 60°, and musculotendinous forces were applied, simulating a 2-legged squat. Intra-articular contact pressures were measured using pressure-sensitive Fuji film. Kinematic data were acquired through digitization of fiducial markers., Results: Vertical tears did not cause a significant change in contact pressure or area. Partial meniscectomy increased maximum contact pressures in the lateral compartment at 30° and 60° from 5.3 MPa to 7.2 MPa and 7.6 MPa, respectively (P = .02, P = .007). Subtotal meniscectomy (8.4 MPa) significantly increased contact pressure compared with partial meniscectomy (7.6 MPa) at 60° (P = .04). Both meniscectomy states significantly increased contact pressures with increasing flexion from 0° to 60° (P < .001, P < .001)., Conclusion: Vertical tears of the lateral meniscus during a simulated 2-legged squat did not significantly change contact pressures and areas compared with an intact meniscus. However, treating these tears with partial and complete meniscectomy significantly increased maximum contact pressures., Clinical Relevance: Biomechanical evidence supports treating vertical lateral meniscus tears with meniscal-sparing techniques as opposed to meniscectomy, which may lead to progressive degenerative joint disease from altered joint biomechanics.

Background: Tibiofemoral instability is a common reason for total knee arthroplasty failure, and may be attributed to soft tissue deficiency and incorrect ligament balancing. There are many different designs of implant with varying levels of constraint to overcome this instability; however there is little advice for surgeons to assess which is suitable for a specific patient, and soft tissue balance testing during arthroplasty is very subjective., Method: The current theories on primary and secondary soft tissue restraints to anterior/posterior, varus/valgus, and internal/external rotational motion of the knee are discussed. The paper reviews biomechanics literature to evaluate instability in the intact and implanted knee., Findings: The paper highlights important intra- and extra-capsular structures in the knee and describes the techniques used by clinicians to assess instability perioperatively. In vitro cadaveric studies were found to be a very useful tool in comparing different implants and contributions of different soft tissues., Interpretation: In vitro cadaveric studies can be utilised in helping less experienced surgeons with soft tissue releases and determining the correct implant. For this to happen, more biomechanical studies must be done to show the impact of release sequences on implanted cadavers, as well as determining if increasingly constrained implants restore the stability of the knee to pre-deficient conditions., (Copyright © 2013. Published by Elsevier Ltd.)

Background: A disadvantage of pivot-shift maneuvers is that the examiner has to subjectively evaluate the degree of pivot shift observed. It is unknown whether the various maneuvers are biomechanically identical., Purpose: To compare biomechanical features of 3 clinical maneuvers for the anterior cruciate ligament (ACL)-deficient knee: the pivot-shift test, the jerk test, and the N-test., Study Design: Controlled laboratory study., Methods: A total of 28 patients with an isolated ACL injury were examined by use of 3 pivot-shift maneuvers (pivot-shift test, jerk test, and N-test). An electromagnetic sensor system was used to evaluate the 3-dimensional knee kinematics of each patient's injured and uninjured knees during each maneuver. Peak coupled anterior tibial translation (pCAT) and maximal acceleration of posterior translation (APT) were measured relative to results during a flexion-extension motion in each test., Results: The pCAT of the pivot-shift test was significantly greater than that of both the jerk test and the N-test (P = .0020 and P < .0001, respectively); there was no statistical difference in pCAT between the jerk test and the N-test. The APT of the N-test was significantly greater than that of both the pivot-shift test and the jerk test (P < .0001), while there was no statistical difference between the pivot-shift and the jerk tests. There was no correlation between pCAT and APT in each test., Conclusion: The pivot-shift test, jerk test, and N-test have different biomechanical characteristics to induce the pivot-shift phenomenon in the ACL-deficient knee. The pivot-shift test produced the largest side-to-side difference in pCAT, whereas the N-test provoked the largest side-to-side difference in APT., Clinical Relevance: The biomechanical differences in pivot-shift maneuvers are caused by technical differences, and clinicians should understand these biomechanical differences while practicing the maneuvers. The electromagnetic sensor system is clinically useful for quantifying the pivot-shift phenomenon.

Background: Excessive trunk motion and deficits in neuromuscular control (NMC) of the lumbopelvic hip complex are risk factors for anterior cruciate ligament (ACL) injury. However, the relationship between trunk motion, NMC of the lumbopelvic hip complex, and triplanar knee loads during a sidestep cutting task has not been examined., Purpose: To determine if there is an association between multiplanar trunk motion, NMC of the lumbopelvic hip complex, and triplanar knee loads with ACL injury during a sidestep cutting task., Study Design: Descriptive laboratory study., Methods: The hip and knee biomechanics and trunk motion of 30 participants (15 male, 15 female) were analyzed during a sidestep cutting task using an optoelectric camera system interfaced to a force plate. Trunk and lower extremity biomechanics were calculated from the kinematic and ground-reaction force data during the first 50% of the stance time during the cutting task. Pearson product moment correlation coefficients were calculated between trunk and lower extremity biomechanics. Multiple linear regression analyses were carried out to determine the amount of variance in triplanar knee loading explained by trunk motion and hip moments., Results: A greater internal knee varus moment (mean, 0.11 ± 0.12 N·m/kg*m) was associated with less transverse-plane trunk rotation away from the stance limb (mean, 20.25° ± 4.42°; r = -0.46, P = .011) and a greater internal hip adduction moment (mean, 0.33 ± 0.25 N·m/kg*m; r = 0.83, P < .05). A greater internal knee external rotation moment (mean, 0.11 ± 0.08 N·m/kg*m) was associated with a greater forward trunk flexion (mean, 7.62° ± 5.28°; r = 0.42, P = .020) and a greater hip internal rotation moment (mean, 0.15 ± 0.16 N·m/kg*m; r = 0.59, P = .001). Trunk rotation and hip adduction moment explained 81% (P < .05) of the variance in knee varus moment. Trunk flexion and hip internal rotation moment explained 48% (P < .05) of the variance in knee external rotation moment., Conclusion: Limited trunk rotation displacement toward the new direction of travel and hip adduction moment are associated with an increased internal knee varus moment, while a combined increase in trunk flexion displacement and hip internal rotation moment is associated with a higher internal knee external rotation moment., Clinical Relevance: Prevention interventions for ACL injury should encourage trunk rotation toward the new direction of travel and limit excessive trunk flexion while adjusting frontal- and transverse-plane hip NMC.

We analyzed the magnetic resonance studies of the knee in 80 subjects, 45 men and 35 women with a mean age of 38.9 years, who showed no pathological condition of the joint. Using an imaging visualization software, the sagittal longitudinal axis of the tibia was identified. The angle between this axis and a line tangent to the bone profile of the tibial plateau (bone slope) and to the superior border of the menisci (meniscal slope) were calculated. Thickness of anterior and posterior portion of menisci and underlying cartilage were also measured. The bone slope averaged 8° and 7.7° on the medial and lateral sides, respectively. The mean meniscal slope was 4.1° and 3.3° on the medial and lateral sides, respectively, with a significant difference compared with the bone slope. Menisci and underlying cartilage were significantly thicker in their posterior than their anterior portion (7.6 and 5.2 mm, respectively, in the medial compartment; 8.6 and 5.2 mm, respectively, in the lateral compartment). The presence of cartilage and menisci implies a significant decrease in the posterior tibial slope. In the lateral compartment, the greater the bone slope, the larger the difference between bone and meniscal slope, which means that a marked posterior tilt of the lateral tibial plateau is decreased by the cartilage and meniscus. These findings should be taken into account in planning surgical procedures which affect the slope of the articular tibial surface., (Copyright © 2012 Wiley Periodicals, Inc.)

Aseptic loosening and other wear-related complications are some of the most frequent late reasons for revision of total knee arthroplasty (TKA). Periprosthetic osteolysis (PPOL) pre-dates aseptic loosening in many cases, indicating the clinical significance of this pathogenic mechanism. A variety of implant-, surgery- and host-related factors have been delineated to explain the development of PPOL. These factors influence the development of PPOL because of changes in mechanical stresses within the vicinity of the prosthetic device, excessive wear of the polyethylene liner, and joint fluid pressure and flow acting on the peri-implant bone. The process of aseptic loosening is initially governed by factors such as implant/limb alignment, device fixation quality and muscle coordination/strength. Later, large numbers of wear particles detached from TKA trigger and perpetuate particle disease, as highlighted by progressive growth of inflammatory/granulomatous tissue around the joint cavity. An increased accumulation of osteoclasts at the bone-implant interface, impairment of osteoblast function, mechanical stresses and increased production of joint fluid contribute to bone resorption and subsequent loosening of the implant. In addition, hypersensitivity and adverse reactions to metal debris may contribute to aseptic TKA failure, but should be determined more precisely. Patient activity level appears to be the most important factor when the long-term development of PPOL is considered. Surgical technique, implant design and material factors are the most important preventative factors, because they influence both the generation of wear debris and excessive mechanical stresses. New generations of bearing surfaces and designs for TKA should carefully address these important issues in extensive preclinical studies. Currently, there is little evidence that PPOL can be prevented by pharmacological intervention., (Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.)

Researchers have reported several compensation methods to estimate bone and joint position from a cluster of skin-mounted markers as influenced by Soft Tissue Artifacts (STA). Tikhonov Regularization Filtering (TRF) as a means to estimate Instantaneous Screw Axes (ISA) was introduced here as a means to reduce the displacement of a rigid body to its simplest geometric form. Recent studies have suggested that the ISA of the knee, i.e., Knee Functional Axes (KFA), might be closely connected to the estimation of constraint forces such as those due to medial and lateral connective tissues. The estimations of ISAs were known to be highly sensitive to noisy data, which may be mathematically ill-posed, requiring smoothing such as that conducted by regularization. The main contribution in this work was to establish the reciprocal connection between the KFA and Ground Reaction Forces (GRF) as a means to estimate joint constraint forces. Presented results compare the computational performance with published kinetic and kinematic joint data generated from an instrumented total knee replacement. Implications of these preliminary findings with respect to dynamic alignment as a functional anatomic metric are discussed.

Lower extremity mechanics during landing have been linked to traumatic and nontraumatic knee injuries, particularly in women's athletics. The effects of efforts to mitigate these risks have not been fully elucidated. We previously reported that a 5° medial wedge reduced ankle eversion and knee valgus. In the present report we further investigated the effect of a 5° medial wedge inserted in the shoes of female athletes on frontal plane hip motion, as well as ankle, knee, hip, and trunk saggital plane motion during a jump landing task. Kinematic data were obtained from 10 intercollegiate female athletes during jump landings from a 31 cm platform with and without a 5° medial wedge. Hip adduction was reduced 1.98° (95% CI 0.97-2.99°) by the medial wedge but saggital plane motions were unaffected. A 5° medial wedge reduces frontal plane motion and takes the knee away from a position associated with anterior cruciate ligament injury and patellofemoral pain syndrome. Although frontal plane motion was not captured it is unlikely to have increased in a bilateral landing task. Thus, it is likely that greater muscle forces were generated in these highly trained athletes to dissipate ground reaction forces when a medial wedge was in place. Additional investigation in younger and lesser trained athletes is warranted to assess the impact of orthotic devices on knee joint mechanics.