Search

Owing to the recent power outages caused by extreme events, installing battery energy storage and backup generators is important to improve resiliency for a grid-tied microgrid. In the design stage, the event occurrence time and duration, which are highly uncertain and cannot be effectively predicted, may affect the needed battery and backup generator capacity but are usually assumed to be pre-determined in utility planning tools. This study investigates the optimal battery and backup generator sizing problem considering the stochastic event occurrence time and duration for the grid-tied microgrid under islanded operation. The reliability requirement is quantified by the mean value of the critical customer interruption time in each stochastic islanding time window (ITW), whose length is the duration and the centre is the occurrence time. The stochastic ITW constraint is then transformed to a probability-weighted expression to derive an equivalent Mixed Integer Linear Programming model. Numerical simulations on a realistic grid-tied PV-based microgrid demonstrate that the total cost is reduced by 11.5% considering the stochastic ITW, compared with the deterministic ITW under the same reliability requirement. [ABSTRACT FROM AUTHOR]

A transmission line emulator has been developed to flexibly represent interconnected ac lines under normal operating conditions in a voltage-source-converter-based power system emulation platform. As the most serious short-circuit fault condition, the three-phase short-circuit fault emulation is essential for power system studies. This paper proposes a model to realize a three-phase short-circuit fault emulation at different locations along a single transmission line or one of several parallel-connected transmission lines. At the same time, a combination method is proposed to eliminate the undesired transients caused by the current reference step changes while switching between the fault state and the normal state. Experiment results verify the developed transmission line three-phase short-circuit fault emulation capability. [ABSTRACT FROM AUTHOR]

The hybrid electric bus (HEB) presents an emerging solution to exhaust gas emissions in urban transport. This paper proposes a multiport bidirectional switched reluctance motor (SRM) drive for solar-assisted HEB (SHEB) powertrain, which not only improves the motoring performance, but also achieves flexible charging functions. To extend the driving miles and achieve self-charging ability, photovoltaic (PV) panels are installed on the bus to decrease the reliance on fuelsbatteries and charging stations. A bidirectional front-end circuit with a PV-fed circuit is designed to integrate electrical components into one converter. Six driving and five charging modes are achieved. The dc voltage is boosted by the battery in generator control unit (GCU) driving mode and by the charge capacitor in battery driving mode, where the torque capability is improved. Usually, an extra converter is needed to achieve battery charging. In this paper, the battery can be directly charged by the demagnetization current in GCU or PV driving mode, and can be quickly charged by the PV panels and GCUAC grids at SHEB standstill conditions, by utilizing the traction motor windings and integrated converter circuit, without external charging converters. Experiments on a three-phase 128 SRM confirm the effectiveness of the proposed drive and control scheme. [ABSTRACT FROM AUTHOR]

In this paper, an equivalent circuit model is developed for a commercial Gallium Nitride (GaN) gate injection transistor (GIT) device at room temperature. The I-V and C-V characteristics are extracted from the commercial device datasheet and fitted in MATLAB. The fitted equations are realized as a combination of behavioral circuit components to be carried out in SPICE simulation. The equivalent circuit model is tested in a simple configuration for I-V curve simulation through varying of parameters and then in a simple boost configuration typical for power electronics applications to check for convergence and expected results. [ABSTRACT FROM AUTHOR]

The temperature-dependent characteristics of the third-generation 10-kV/20-A SiC MOSFET including the static characteristics and switching performance are carried out in this paper. The steady-state characteristics, including saturation current, output characteristics, antiparallel diode, and parasitic capacitance, are tested. A double pulse test platform is constructed including a circuit breaker and gate drive with >10-kV insulation and also a hotplate under the device under test for temperature-dependent characterization during switching transients. The switching performance is tested under various load currents and gate resistances at a 7-kV dc-link voltage from 25 to 125 ˚C and compared with previous 10-kV MOSFETs. A simple behavioral model with its parameter extraction method is proposed to predict the temperature-dependent characteristics of the 10-kV SiC MOSFET. The switching speed limitations, including the reverse recovery of SiC MOSFET's body diode, overvoltage caused by stray inductance, crosstalk, heat sink, and electromagnetic interference to the control are discussed based on simulations and experimental results. [ABSTRACT FROM AUTHOR]

Dead time significantly affects the reliability, power quality, and efficiency of voltage-source converters. For silicon carbide (SiC) devices, considering the high sensitivity of turn-off time to the operating conditions (> 5× difference between light load and full load) and characteristics of inductive loads (> 2× difference between motor load and inductor), as well as large additional energy loss induced by the freewheeling diode conduction during the superfluous dead time (∼15% of the switching loss), then the traditional fixed dead time setting becomes inappropriate. This paper introduces an approach to adaptively regulate the dead time considering the current operating condition and load characteristics via synthesizing online monitored turn-off switching parameters in the microcontroller with an embedded preset optimization model. Based on a buck converter built with 1200-V SiC MOSFETs, the experimental results show that the proposed method is able to ensure reliability and reduce power loss by 12% at full load and 18.2% at light load (8% of the full load in this case study). [ABSTRACT FROM AUTHOR]

This paper presents a steady-state model of MMC for the second-order phase voltage ripple prediction under unbalanced conditions, taking the impact of negative-sequence current control into account. From the steady-state model, a circular relationship is found among current and voltage quantities, which can be used to evaluate the magnitudes and initial phase angles of different circulating current components. Moreover, in order to calculate the circulating current in a point-to-point MMC-based HVdc system under unbalanced grid conditions, the derivation of equivalent dc impedance of an MMC is discussed as well. According to the dc impedance model, an MMC inverter can be represented as a series connected R–L–C branch, with its equivalent resistance and capacitance directly related to the circulating current control parameters. Experimental results from a scaled-down three-phase MMC system under an emulated single-line-to-ground fault are provided to support the theoretical analysis and derived model. This new models provides an insight into the impact of different control schemes on the fault characteristics and improves the understanding of the operation of MMC under unbalanced conditions. [ABSTRACT FROM PUBLISHER]

This paper presents the development of a scaled four-terminal high-voltage direct current (HVDC) testbed, including hardware structure, communication architecture, and different control schemes. The developed testbed is capable of emulating typical operation scenarios including system start-up, power variation, line contingency, and converter station failure. Some unique scenarios are also developed and demonstrated, such as online control mode transition and station re-commission. In particular, a dc line current control is proposed, through the regulation of a converter station at one terminal. By controlling a dc line current to zero, the transmission line can be opened by using relatively low-cost HVDC disconnects with low current interrupting capability, instead of the more expensive dc circuit breaker. Utilizing the dc line current control, an automatic line current limiting scheme is developed. When a dc line is overloaded, the line current control will be automatically activated to regulate current within the allowable maximum value. [ABSTRACT FROM AUTHOR]

Hybrid ac/dc transmission extends the power transfer capacity of existing long ac lines closer to their thermal limit, by superposing the dc current onto three-phase ac lines through a zigzag transformer. However, this transformer could suffer saturation under unbalanced line impedance conditions. This paper introduces the concept of hybrid line impedance conditioner (HLIC) as a cost-effective approach to compensate for the line unbalance and therefore avoid saturation. The topology and operation principle are presented. The two-level control strategy is described, which enables autonomous adaptive regulation without the need of system-level control. Design and implementation are also analyzed, including dc-link capacitance as one of the key line conditioner components, HLIC installation, and protection under fault conditions. The cost study on this HLIC-based hybrid system is also performed to reveal the benefits of the solution. Simulation results and experimental results based on a down-scaled prototype are provided to verify the feasibility of the proposed approach. [ABSTRACT FROM AUTHOR]

Small-signal stability is an important concern in three-phase inverter-based ac power systems. The impedance-based approach based on the generalized Nyquist stability criterion (GNC) can analyze the stability related with the medium and high-frequency modes of the systems. However,. the GNC involves the right-half-plane (RHP) pole calculation of return-ratio transfer function matrices, which cannot be avoided for stability analysis of complicated ac power systems. Therefore, it necessitates the detailed internal control information of the inverters, which is not normally available for commercial inverters. To address this issue, this paper introduces the component connection method (CCM) in the frequency domain for stability analysis in the synchronous d–q frame, by proposing a method of deriving the impedance matrix of the connection networks of inverter-based ac power systems. Demonstration on a two-area system and a microgrid shows that: The CCM-enabled approach can avoid the RHP pole calculation of return-ratio matrices and enables the stability analysis by using only the impedances of system components, which could be measured without the need for the internal information. A stability analysis method based on d–q impedances, the CCM, and the determinant-based GNC is also proposed to further simplify the analysis process. Inverter controller parameters can be designed as stability regions in parameter spaces, by repetitively applying the proposed stability analysis method. Simulation and experimental results verify the validity of the proposed stability analysis method and the parameter design approach. [ABSTRACT FROM PUBLISHER]

Newly emerged gallium nitride (GaN) devices feature ultrafast switching speed and low on-state resistance that potentially provide significant improvements for power converters. This paper investigates the benefits of GaN devices in an LLC resonant converter and quantitatively evaluates GaN devices’ capabilities to improve converter efficiency. First, the relationship of device and converter design parameters to the device loss is established based on an analytical model of LLC resonant converter operating at the resonance. Due to the low effective output capacitance of GaN devices, the GaN-based design demonstrates about 50% device loss reduction compared with the Si-based design. Second, a new perspective on the extra transformer winding loss due to the asymmetrical primary-side and secondary-side current is proposed. The device and design parameters are tied to the winding loss based on the winding loss model in the finite element analysis (FEA) simulation. Compared with the Si-based design, the winding loss is reduced by 18% in the GaN-based design. Finally, in order to verify the GaN device benefits experimentally, 400- to 12-V, 300-W, 1-MHz GaN-based and Si-based LLC resonant converter prototypes are built and tested. One percent efficiency improvement, which is 24.8% loss reduction, is achieved in the GaN-based converter. [ABSTRACT FROM AUTHOR]

A hardware testbed platform emulating multiple-area power system scenario dynamics has been established aiming at multiple time-scale real-time emulations. In order to mimic real power flow situations in the utility system, the load emulators have to behave like real ones in both their static and dynamic characteristics. A constant-impedance, constant-current, and constant-power (ZIP) model has been used for static load types, while a three-phase induction motor model has been built to represent dynamic load types. In this paper, ways of modeling ZIP and induction motor loads and the performance of each load emulator are discussed. Comparisons between simulation and experimental results are shown as well for the validation of the emulator behaviors. A real-time composite power load emulator is then demonstrated with desired characteristics and detailed transients for representing a power system PQ bus dynamics. [ABSTRACT FROM PUBLISHER]

Featuring modularity and high efficiency, a modular multilevel converter (MMC) has become a promising topology in high-voltage direct-current transmission systems. However, its distributed capacitors lead to a more complicated startup process than that of a two-level converter. To fully understand this issue, the charging loops of an MMC rectifier and an MMC inverter during an uncontrolled precharge period are analyzed in this paper, with special focus on the necessity of additional capacitor charging schemes. Moreover, a small-signal model of a capacitor charging loop is first derived according to the internal dynamics of the MMC inverter. Based on this model, a novel startup strategy incorporating an averaging capacitor voltage loop and a feedforward control is proposed, which is capable of an enhanced dynamic response and system stability without sacrificing voltage control precision. The design considerations of the control strategy are also given in detail. Simulation results from a back-to-back MMC system supplying passive loads and experimental results from a scaled-down MMC prototype are provided to support the theoretical analysis and the proposed control scheme. [ABSTRACT FROM PUBLISHER]

This paper presents the paralleling operation of three-phase current-source rectifiers (CSRs) as the front-end power conversion stage of data center power supply systems based on 400- \Vdc power delivery architecture, which has been proven to have higher efficiency than traditional ac architectures. A control algorithm of paralleled three-phase CSRs is introduced to achieve balanced outputs and individual rectifier module hot swap, which are required by power supply systems. By using silicon carbide (SiC) power semiconductors, SiC MOSFETs, and Schottky diodes, the power losses of the front-end stage are reduced, and the power supply system efficiency can be further increased. The prototype of a 19-kW front-end rectifier to convert 480 \Vac,rms to 400 \Vdc , based on three paralleled three-phase CSRs, is developed. Each CSR is an all-SiC converter and designed for high efficiency, and the front-end stage full-load efficiency is greater than 98% from experimental tests. The balanced outputs and individual converter hot swap are realized in the hardware prototype too. [ABSTRACT FROM AUTHOR]

This paper presents a modular cascaded H-bridge multilevel photovoltaic (PV) inverter for single- or three-phase grid-connected applications. The modular cascaded multilevel topology helps to improve the efficiency and flexibility of PV systems. To realize better utilization of PV modules and maximize the solar energy extraction, a distributed maximum power point tracking control scheme is applied to both single- and three-phase multilevel inverters, which allows independent control of each dc-link voltage. For three-phase grid-connected applications, PV mismatches may introduce unbalanced supplied power, leading to unbalanced grid current. To solve this issue, a control scheme with modulation compensation is also proposed. An experimental three-phase seven-level cascaded H-bridge inverter has been built utilizing nine H-bridge modules (three modules per phase). Each H-bridge module is connected to a 185-W solar panel. Simulation and experimental results are presented to verify the feasibility of the proposed approach. [ABSTRACT FROM PUBLISHER]

A three-phase nonlinear load emulator using a power electronic converter is presented in this study. The proposed nonlinear load emulator is intended to be used in an ultrawide-area grid transmission network emulator, also called hardware testbed (HTB). The emulator converter is controlled in rectifier mode to act as the real nonlinear three-phase diode rectifier load. This paper presents an accurate controller for the nonlinear load emulator based on a three-phase diode rectifier system to be used in the HTB. This study also demonstrates simulation and experimental results for verification of the proposed controller. [ABSTRACT FROM AUTHOR]

Overcurrent protection of silicon carbide (SiC) metal–oxide–semiconductor field-effect transistors (MOSFETs) remains a challenge due to lack of practical knowledge. This paper presents three overcurrent protection methods to improve the reliability and overall cost of SiC MOSFET-based converters. First, a solid-state circuit breaker (SSCB) composed primarily by a Si IGBT and a commercial gate driver IC is connected in series with the dc bus to detect and clear overcurrent faults. Second, the desaturation technique using a sensing diode to detect the drain-source voltage under overcurrent faults is implemented as well. Third, a novel active overcurrent protection scheme through dynamic evaluation of fault current level is proposed. The design considerations and potential issues of the protection methods are described and analyzed in detail. A phase-leg configuration-based step-down converter is built to evaluate the performance of the protection schemes under various conditions, considering variation of fault type, decoupling capacitance, protection circuit parameters, etc. Finally, a comparison is made in terms of fault response time, temperature-dependent characteristics, and applications to help designers select a proper protection method. [ABSTRACT FROM PUBLISHER]

This paper presents an improved phase disposition pulsewidth modulation (PWM) (PDPWM) for the modular multilevel converter (MMC) which is based on the selective loop bias mapping (SLBM) method. Its main idea is to change the bias of the PDPWM carrier wave cycling according to the balance situation of the system. This new modulation method can operate at symmetric condition to generate an output voltage with as many as 2N + 1 levels, and by SLBM, the voltages of the upper/lower arm capacitors can be well balanced. Compared to carrier phase-shifted PWM, this method is more easily to be realized and has much stronger dynamic regulation ability. Specially, this method has no issues of sorting, which makes it suitable for MMC with a large number of submodules in one leg. With simulation and experiments, the validity of the proposed method has been shown. [ABSTRACT FROM AUTHOR]

In this paper, the analysis of space vector modulation of a three-phase/wire/level Vienna rectifier is conducted, according to which the implementation of the equivalent carrier-based pulsewidth modulation is deduced theoretically within each separated sector in the diagram of vectors. The voltage balancing ability of dc-link neutral point, which depends on the uneven distribution of short vectors, is analyzed as well. An adaptive and robust controller to balance the output voltage under the unbalanced load limit for different modulation indices is proposed. The proposed controller can work at wide range of unbalanced load condition as well. Furthermore, the maximum unbalanced load is deduced versus the modulation index m when the converter works in unity power factor. An experimental prototype of 2.5 kW was built to verify the effectiveness of the theoretical analysis. Finally, the tested unbalanced limit of outputs for the experimental platform was given under different modulation indices. The output voltages for dual bus are balanced, and the theoretical analysis is verified. [ABSTRACT FROM PUBLISHER]

This paper proposed an improved phase disposition pulse width modulation (PDPWM) for a modular multilevel inverter which is used for Photovoltaic grid connection. This new modulation method is based on selective virtual loop mapping, to achieve dynamic capacitor voltage balance without the help of an extra compensation signal. The concept of virtual submodule (VSM) is first established, and by changing the loop mapping relationships between the VSMs and the real submodules, the voltages of the upper/lower arm's capacitors can be well balanced. This method does not requiring sorting voltages from highest to lowest, and just identifies the MIN and MAX capacitor voltage's index which makes it suitable for a modular multilevel converter with a large number of submodules in one arm. Compared to carrier phase-shifted PWM (CPSPWM), this method is more easily to be realized in field-programmable gate array and has much stronger dynamic regulation ability, and is conducive to the control of circulating current. Its feasibility and validity have been verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

A new approach for modulation of an 11-level cascade multilevel inverter using selective harmonic elimination is presented in this paper. The dc sources feeding the multilevel inverter are considered to be varying in time, and the switching angles are adapted to the dc source variation. This method uses genetic algorithms to obtain switching angles offline for different dc source values. Then, artificial neural networks are used to determine the switching angles that correspond to the real-time values of the dc sources for each phase. This implies that each one of the dc sources of this topology can have different values at any time, but the output fundamental voltage will stay constant and the harmonic content will still meet the specifications. The modulating switching angles are updated at each cycle of the output fundamental voltage. This paper gives details on the method in addition to simulation and experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a fully integrated silicon carbide (SiC)-based six-pack power module is designed and developed. With 1200-V, 100-A module rating, each switching element is composed of four paralleled SiC junction gate field-effect transistors (JFETs) with two antiparallel SiC Schottky barrier diodes. The stability of the module assembly processes is confirmed with 1000 cycles of −40 °C to +200 °C thermal shock tests with 1.3 °C/s temperature change. The static characteristics of the module are evaluated and the results show 55 mΩ on-state resistance of the phase leg at 200 °C junction temperature. For switching performances, the experiments demonstrate that while utilizing a 650-V voltage and 60-A current, the module switching loss decreases as the junction temperature increases up to 150 °C. The test setup over a large temperature range is also described. Meanwhile, the shoot-through influenced by the SiC JFET internal capacitance as well as package parasitic inductances are discussed. Additionally, a liquid cooled three-phase inverter with 22.9 cm × 22.4 cm × 7.1 cm volume and 3.53-kg weight, based on this power module, is designed and developed for electric vehicle and hybrid electric vehicle applications. A conversion efficiency of 98.5% is achieved at 10 kHz switching frequency at 5 kW output power. The inverter is evaluated with coolant temperature up to 95 °C successfully. [ABSTRACT FROM AUTHOR]

In order to apply power electronics systems to applications such as superconducting systems under cryogenic temperatures, it is necessary to investigate the characteristics of different parts in the power electronics systems. This paper reviews the influence of cryogenic temperature on power semiconductor devices including Si and wide bandgap switches, integrated circuits, passive components, interconnection and dielectric materials, and some typical cryogenic converter systems. Also, the basic theories and principles are given to explain the trends for different aspects of cryogenically cooled converters. Based on the review, Si active power devices, bulk CMOS based integrated circuits, nanocrystalline and amorphous magnetic cores, NP0 ceramic and film capacitors, thin/metal film and wirewound resistors are the components suitable for cryogenic operation. Pb-rich PbSn solder or In solder, classic PCB material, most insulation papers and epoxy encapsulant are good interconnection and dielectric parts for cryogenic temperatures.