Search

Ochratoxin A (OTA) can occur in a large variety of commodities (cereals, beans, groundnuts, spices, dried fruits, coffee, beer, wine) and, because of a carry-over effect, in milk, pig blood, liver, and kidney, and poultry meat from animals fed with contaminated feed. Because of the persistence of OTA in the food chain, exposure to the compound is a potential human health hazard. This has prompted adoption of regulatory limits in several countries which, in turn, implies the development of suitable validated and official analytical methods and rapid screening tests for cost-effective food control on a large scale. Liquid chromatography with fluorescence detection (LC-FLD), coupled with immunoaffinity column (IAC) clean-up, is the most widely employed analytical technique. LC coupled with electrospray-ionization mass spectrometry (MS) has detection limits comparable with those of LC-FLD and the selectivity of IAC can be achieved by tandem (MS-MS) or sequential (MS(n)) detection. Synthetic counterparts to natural antibodies in the form of molecularly imprinted polymers seem a promising alternative to IAC for sample preparation. New analytical approaches to rapid, low-cost screening methods, for example those based on biosensors and dip-stick-like kits, are a direction in which innovation can be expected. Analytical methods for evaluation of the occurrence of OTA in foods, human exposure, and risk assessment are critically reviewed.

A method based on liquid chromatography with electrospray ionisation ion trap mass spectrometry, for the determination of ochratoxin A (OTA) in meat products using ochratoxin B (OTB) as an internal standard, is described. Fragmentation patterns of OTA and OTB were studied by sequential mass spectrometry. Trace determination was then accomplished by consecutive reaction monitoring (CRM) of a fragment obtained by MS(3) experiments. This led to a better signal-to-noise ratio and to a higher specificity of the technique. The response to OTA was linear over at least one concentration decade with a limit of detection of 0.6 ng/g. The method was applied to pig tissue samples naturally contaminated by OTA., (Copyright 2004 John Wiley & Sons, Ltd.)

A solid-phase microextraction (SPME) method, coupled to liquid chromatography with diode array UV detection (LC-UV/DAD), for the simultaneous determination of cyclopiazonic acid, mycophenolic acid, tenuazonic acid, and ochratoxin A is described. Chromatographic separation was achieved on a propylamino-bonded silica gel stationary phase using acetonitrile/methanol/ammonium acetate buffer mixture (78:2:20, v/v/v) as mobile phase. SPME adsorption and desorption conditions were optimized using a silica fiber coated with a 60 microm thick polydimethylsiloxane/divinylbenzene film. Estimated limits of detection and limits of quantitation ranged from 3 to 12 ng/mL and from 7 to 29 ng/mL, respectively. The method has been applied to cornflake samples. Samples were subjected to a preliminary short sonication in MeOH/2% KHCO(3) (70:30, v/v); the mixture was evaporated to near dryness and reconstituted in 1.5 mL of 5 mM phosphate buffer (pH 3) for SPME followed by LC-UV/DAD. The overall procedure had recoveries (evaluated on samples spiked at 200 ng/g level) ranging from 74 +/- 4 to 103 +/- 9%. Samples naturally contaminated with cyclopiazonic and tenuazonic acids were found; estimated concentrations were 72 +/- 9 and 25 +/- 6 ng/g, respectively.

Soluble species generated during the electropolymerization of o-phenylenediamine (o-PD) on platinum electrodes in aqueous buffers at different pH values were investigated by electrospray ionization ion trap sequential mass spectrometry (ESI-ITMS(n)). The main protonated molecules (MH(+)) detected in the full scan ESI-MS spectra of the electrolytic solutions were isolated in the ion trap and sequentially fragmented (MS(n), with n up to 5) to obtain fragmentation patterns. The latter led to hypotheses as to the molecular structures of the soluble products of o-PD electropolymerization; it appeared that all of them are actually oligomeric species in different oxidation states. In particular, o-PD dimers, trimers and tetramers could be identified and three common structural features were found, namely: the presence of phenazine, 1,4-benzoquinonediimine, and secondary amine (acting as bridges between benzene rings) units. These findings are in agreement with those already reported for the surface structure of the polymeric films formed on the platinum electrodes during o-PD polymerization, thus suggesting that a close relationship exists between the soluble oligomers and the polymer itself., (Copyright 2003 John Wiley & Sons, Ltd.)

A disposable glucose biosensor based on glucose oxidase immobilized on tetrathiafulvalene-tetracyanoquinodimethane (ITF-TCNQ) conducting organic salt synthesized in situ onto an overoxidized poly(pyrrole) (PPy(ox).) film is described. The TIF-TCNQ crystals grow through the nonconducting polypyrrole film (ensuring electrical connection to the underlying Pt electrode) and emerge from the film forming a treelike structure. The PPy(ox) film prevents the interfering substances from reaching the electrode surface. The sensor behavior can be modeled by assuming a direct reoxidation of the enzyme at the surface of the TTF-TCNQ crystals. A heterogeneous rate constant around 10(-6) - 10(-7) cm s(-1) has been estimated. The biosensor is nearly oxygen- and interference-free and when integrated in a flow injection system displays a remarkable sensitivity (70 nA/mM) and stability.

A solid-phase microextraction gas chromatography-mass spectrometry method has been developed for the determination of triazole residues, such as triadimefon, propiconazole, myclobutanil and penconazole. The method has been successfully applied to the analysis of strawberries and wine samples. The procedure is solvent-free, simple and highly sensitive. Within-day and day-to-day RSDs ranged between 2-11% and 7-28%, respectively. Detection limits estimated at a signal-to-noise ratio of 3 ranged between 30 (propiconazole) and 100 ng/kg (triadimefon). Since the detection limits achieved by this method are well below the maximum residue levels for wine (or grapes) and strawberries recommended by the European legislation, it can be conveniently used as a low-cost rapid screening method for the contamination of the considered samples.

A solid-phase microextraction-gas chromatography-mass spectrometry (SPME-GC-MS) method for the simultaneous determination of the organophosphorus pesticides (OPPs), phorate, diazinon, methyl-parathion, fenitrothion, malathion, fenthion, ethyl-parathion and methidathion, has been developed to study their soil/water distribution. The method was used in conjunction with a conventional 'batch equilibrium method' to assess the soil adsorption coefficients (Koc) of the target compounds in different soil samples with known organic carbon content. Contrary to traditional techniques, the present method is fast, solvent-free and highly sensitive, thus permitting the assessment of the Koc values of the target compounds even at low soil concentration levels, close to those encountered in real field contamination, where the Freudlich adsorption isotherms can be considered to be linear. The estimated Koc values were found to be in good agreement with those reported in the literature.

A new high-performance liquid (HPLC) chromatographic method is described for cyclopiazonic acid (CPA) determination in fungal cultures on a propylamino-bonded stationary phase with a CH3CN/CH3COONH4 buffer as mobile phase. Retention of CPA on propylamino modified silica under acidic conditions (protonated amino groups and deprotonated CPA) is governed by a mixed ion-exchange-reversed-phase mechanism. In addition to non-polar (hydrophobic) interactions, polar interactions with the surface silanols are also possible and become important as the polarity of the mobile phase decreases. A detection limit of 25 pg of CPA standard is obtained that represents an improvement of more than two orders of magnitude compared to existing HPLC procedures. UV-detector response was linear to 200 ng of CPA. Fungal extracts can be analysed after a simple dilution step with UV diode array detection that provides peak identity/purity assessment. The suitability of the proposed method as a rapid confirmatory test to assess the toxigenic potential of different Aspergillus and Penicillium strains is demonstrated by the analysis of 54 fungal extracts.

A disposable amperometric biosensor for the determination of anticholinesterase activity in soil extracts is described. The sensitive membrane was obtained by co-crosslinking acetylcholinesterase and choline oxidase with bovine serum albumin using glutaraldehyde. The anticholinesterase activity of the soil extract was measured using chronoamperometry at 650 mV vs. Ag/AgCl to monitor the biocatalytically produced H2O2 before and after the inhibition step. An inhibition percentage of 38 +/- 4% was recorded for soil extracts spiked with 10 ppb of ethyl parathion. The device has the potential to be used as a gross sensor for the assessment of anticholinesterase activity in soil extracts.

One microband of an array of four microband electrodes (1 mm long and 25 microm wide with a 25 microm gap) was modified with glucose oxidase by direct electrochemically assisted immobilisation, giving a stable microbiosensor with an apparent Michaelis-Menten constant of 12 mM and an i(max) of 80 nA. Cross-talk effects on the adjacent microbands were studied and three different methods for their elimination were tested: the most efficient one involved catalase deposition on the adjacent microband. Under these conditions, the maximum response at the unmodified microbands was in the worst case about 3% compared with the response of the modified microband. This approach has the potential to fabricate a multianalyte microbiosensor.

A liquid chromatography (LC) detector based on a fast response and sensitive bienzyme amperometric biosensor for acetylcholine (ACh) and choline (Ch) is described. The detector fabrication consisted of glutaraldehyde co-crosslinking of acetylcholinesterase and choline oxidase with bovine serum albumin on the Pt working electrode of a conventional thin-layer electrochemical flow cell. The influence of some experimental parameters (e.g., enzyme loading, thickness of the bienzyme layer, flow rate) on the detector characteristics has been studied in order to optimize the analyte response while minimizing band-broadening and distortion. A mobile phase consisting of a phosphate buffer (I, 0.1 M; pH, 6.5) containing 5 mM sodium hexane sulfonate and 10 mM tetramethylammonium phosphate was found to give very satisfactory resolution and peak shape in ion-pair, reversed-phase LC. Linear responses were observed over at least four decades and absolute detection limits (at a signal-to-noise ratio of 3) were 12 and 27 fmol injected for Ch and ACh, respectively. After one month of intensive use in the LC system, the detector retained about 70% of its initial sensitivity. The potential of the described approach is demonstrated by the simultaneous determination of Ch and ACh in rat brain tissue homogenates.

A disposable lactate biosensor able to operate in flow injection analysis is described and characterized. The biosensing layer, obtained by glutaraldehyde co-crosslinking of lactate oxidase with bovine serum albumin, was cast on an underlying electropolymerized layer of overoxidized polypyrrole. The resulting biosensor was interference-free and showed a K'M value of 2.4 mmol l-1 and a maximum current density of 440 microA cm-2. When integrated in a flow injection analysis system, a sensitivity of 300 +/- 10 nA mmol-1 l, a linear response up to 1 mmol l-1 and detection limits in the low micromolar range were obtained. The introduction of a microdialysis membrane-based sampler reduced the sensitivity to 7.9 +/- 0.2 nA mmol-1 l and extended the linear range up to 50 mmol l-1 lactate. The anti-interference characteristics of the biosensor permitted lactate determination in untreated milk and diluted yoghurt samples.

The kinetics of the reaction between chlortoluron, a phenylurea herbicide [N'-(2-hydroxy-4-methyl-5-chlorophenyl)-N,N-dimethylurea], and hypochlorite, the active species in water disinfection processes involving chlorine, were investigated by HPLC-UV and HPLC-electrospray ionisation mass spectrometry (HPLC-ESI-MS). In particular, the concentrations of the main chlortoluron by-products were monitored as a function of time by HPLC-ESI-MS and a kinetic model was developed to fit the relevant curves. The results showed that chlortoluron degradation starts with two parallel pathways, namely, chlorination and hydroxylation of the aromatic ring, which are then followed by consecutive chlorination reactions, and after almost 2 weeks by ring opening and partial mineralisation, as confirmed by head-space solid-phase microextraction gas chromatography-MS (SPME-GC-MS) and total organic carbon (TOC) measurements. Kinetic constants for the first reactions of the overall process, under pseudo-first-order conditions (hypochlorite excess), were estimated by a fitting procedure.

A fast response, needle-type glucose microbiosensor has been fabricated by a one-step electrochemical immobilisation of glucose oxidase in a polypyrrole film. The sensor shows a remarkable rejection of electroactive interferences, especially paracetamol. The maximum bias observed in the worst situation never exceeded the value of 6%. The fabrication procedure delivered very reproducible devices and the sensitivity of a newly prepared biosensor was typically 650 nA mM(-1) cm(-2). The kinetic parameters, obtained from an existing model, permitted to understand the sensor behaviour.

A solid-phase microextraction-gas chromatography-mass spectrometry (SPME-GC-MS) method was developed for the evaluation of the leachability order of selected triazines (propazine, terbuthylazine, sebuthylazine, ametryn, prometryn and terbutryn) in soil/sediment samples (organic carbon content ranging from 0.19 to 0.42%), analysing fractions collected from a soil packed microcolumn elution experiments. The procedure is fast, simple, highly sensitive and solvent free. SPME-GC-MS was also employed for the quantitative determination of triazines in the soil leachate, since the method showed good recovery yield. Detection limits were always better than 1 ng ml(-1). The method was tested on a contaminated landfill top soil. Prometryn and ametryn were identified through their MS spectra and then quantified. Terbuthylazine was used to assess recovery. Results compared well with those obtained by solvent extraction followed by HPLC-UV detection.

The most significant goals achieved in the course of the last decade in the design of amperometric biosensors based on redox enzymes entrapped in electrosynthesised polymeric films are reviewed. Particular emphasis is devoted to non-conducting polymers with built-in permselectivity that revealed very promising materials for designing fast-response and interference-free, H2O2 detecting, amperometric biosensors. The role of surface analytical techniques to provide structural information allowing a better understanding of polymers properties and their relationship with the ultimate performance of the final device is also outlined. The most relevant applications of amperometric biosensors based on electropolymerised films to real samples analysis are also reviewed and some possible future trends highlighted.

The main degradation by-products of the herbicide chlortoluron formed during water disinfection with HOCl/ClO(-) have been separated and identified by liquid chromatography/electrospray ionisation sequential mass spectrometry (LC/ESI-MS(n)). Chlorination and hydroxylation reactions seem to occur exclusively on the aromatic ring of chlortoluron, leading to by-products which show characteristic fragmentation patterns. Indeed, chlortoluron-like ESI spectra were always observed for chlorinated by-products, showing only a fragment at m/z 72. In contrast, hydroxylated and chloro/hydroxylated by-products gave a much more complex fragmentation pattern that could be elucidated by MS(n) (n = 1-4) experiments. A mechanistic scheme rationalising the observed fragmentation pattern is proposed and discussed. Copyright 2000 John Wiley & Sons, Ltd.

An interference and cross-talk free dual electrode amperometric biosensor integrated with a microdialysis sampling system is described, for simultaneous monitoring of glucose and lactate by flow injection analysis. The biosensor is based on a conventional thin layer flow-through cell equipped with a Pt dual electrode (parallel configuration). Each Pt disk was modified by a composite bilayer consisting of an electrosynthesised overoxidized polypyrrole (PPYox) anti-interference membrane covered by an enzyme entrapping gel, obtained by glutaraldehyde co-crosslinking of glucose oxidase or lactate oxidase with bovine serum albumin. The advantages of covalent immobilization techniques were coupled with the excellent interference-rejection capabilities of PPYox. Ascorbate, cysteine, urate and paracetamol produced lactate or glucose bias in the low micromolar range; their responses were, however, completely suppressed when the sample was injected through the microdialysis unit. Under these operational conditions the flow injection responses for glucose and lactate were linear up to 100 and 20 mM with typical sensitivities of 9.9 (+/- 0.1) and 7.2 (+/- 0.1) nA/mM. respectively. The shelf-lifetime of the biosensor was at least 2 months. The potential of the described biosensor was demonstrated by the simultaneous determination of lactate and glucose in untreated tomato juice samples; results were in good agreement with those of a reference method.

A simple reversed-phase liquid chromatographic (LC) method for the determination of urinary 5-methyl-2'-deoxycytidine (m5dCyd), recently claimed (on the basis of an imuno-technique) to be a potential marker for leukaemia, has been developed. Sample pre-treatment is based on a microcolumn clean-up step with an average recovery of 79% and a RSD of 3%. Detection limit was 0.2 microg/ml which is about tenfold lower than levels previously measured by an ELISA method in urine of healthy individuals. The creatinine (Cre) excretion, necessary for normalising the m5dCyd excretion, was evaluated by ion-pair liquid chromatography which permitted the simultaneous determination of pseudouridine (psi), a modified nucleoside also potentially useful as a marker for leukaemia. The described LC procedures were applied to the analysis of urine samples from healthy individuals and leukaemia patients. While the urinary psi/Cre ratio was found significantly increased for leukaemia patients, the urinary m5dCyd levels in healthy individuals were below the detection limits and did not increase in presence of the malignant disease.

The behaviour of 5-methyl-2'-deoxycytidine (m(5)dCyd, claimed to be a potential marker for leukaemia) during the electrospray process was studied. In particular, considerations concerning the effect of solution chemistry (e.g. analyte concentration, pH, etc.) on electrospray ionization mass spectra were drawn. Furthermore, a procedure using liquid chromatography/electrospray ionization tandem mass spectrometry (LC/ESI-MS/MS) for the determination of urinary m(5)dCyd is described. The method is simple, sensitive and highly specific. The pre-treatment procedure gave an average recovery of 79% (relative standard deviation (RSD) of 3%). Method performance was evaluated on spiked urine samples covering the concentration range from 50 ng/mL to 10 microgram/mL, the same as that of an existing inhibition ELISA method. Contrary to findings based on this immunoassay technique, urinary m(5)dCyd in healthy individuals was not detectable and did not increase in the presence of the malignant disease., (Copyright 1999 John Wiley & Sons, Ltd.)

An enzyme switch, or microelectrochemical enzyme transistor, responsive to hydrogen peroxide was made by connecting two carbon band electrodes (∼10 μm wide, 4.5 mm long separated by a 20-μm gap) with an anodically grown film of poly(aniline). Horseradish peroxidase (EC 1.11.1.7) was either adsorbed onto the poly(aniline) film or immobilized in an insulating poly(1,2-diaminobenzene) polymer grown electrochemically on top of the poly(aniline) film to complete the device. In the completed device, the conductivity of the poly(aniline) film changes from conducting (between - 0.05 and + 0.3 V vs SCE at pH 5) to insulating (>+0.3 V vs SCE at pH 5) on addition of hydrogen peroxide. The change in conductivity is brought about by oxidation of the poly(aniline) film by direct electrochemical communication between the enzyme and the conducting polymer. This was confirmed by measuring the potential of the poly(aniline) film during switching of the conductivity in the presence of hydrogen peroxide. The devices can be reused by rereducing the poly(aniline) electrochemically to a potential below +0.3 V vs SCE. A blind test showed that the device can be used to determine unknown concentrations of H(2)O(2) in solution and that, when used with hydrogen peroxide concentrations below 0.5 mmol dm(-)(3), the same device maybe reused several times. The possible development of devices of this type for use in applications requiring the measurement of low levels of hydrogen peroxide or horseradish peroxidase is discussed.

A high performance liquid chromatography method for the determination of N3-methyl-5'-deoxy-5-fluorouridine, a possible metabolic product of the anticancer pro-drug 5'-deoxy-5-fluorouridine, in human serum and urine is described. Sample treatment involved addition of internal standard (5-bromouracil) and protein precipitation with ammonium sulphate (serum samples) followed by liquid-liquid extraction with ethyl acetate-isopropanol (90:10, v/v). The average recovery at 0.5 mg ml-1 level was (80 +/- 4%). A linear response extending over two decades of concentration was observed. Detection limits of 50 and 100 ng ml-1 were obtained in serum and urine, respectively.

A glucose amperometric biosensor based on glucose oxidase immobilized on an overoxidized polypyrrole (PPyox) platinum modified electrode, by glutaraldehyde co-crosslinking with bovine serum albumine, is described. The advantages of covalent immobilization techniques (e.g. high loading and long-term stability of the enzyme) are coupled with the excellent interferent rejection of electrosynthesized non-conducting polymers. The sensor showed an apparent Michaelis-Menten constant of 16 +/- 0.8 mM, a maximum current density of 490 microA/cm2 and a shelf lifetime of at least 3 months. Ascorbate, urate, cysteine and acetaminophen at their maximum physiological concentrations produced a glucose bias in the low micromolar range. Flow-injection response was linear up to 20 mM glucose with typical sensitivity of 84.0 +/- 1.5 nA/mM. The sensor was tested for glucose determination of untreated serum samples from both normal and diabetic subjects; results of amperometric assay compared well with those obtained by a standard enzymatic-colorimetric method.

The use of a glucose biosensor coupled to microdialysis sampling in a flow injection analysis system is described to follow the growth of Escherichia coli in a glucose-containing liquid culture medium. The experimental set-up permitted a throughput rate of 25 samples h-1. Growth curves were modelled by a modified Gompertz equation, which permitted the determination of lag time and maximum specific growth rate. The time required to produce an appreciable variation in the biosensor response (minimum detection time, MDT) was determined. A plot of MDT versus microbial concentration was found to be linear in the range 10(6)-10(10) colony forming units (cfu) ml-1. A microbial concentration of 10(6) cfu ml-1 can be detected after about 5 h.

Evidence of in vivo biomethylation of the anticancer pro-drug 5'-deoxy-5-fluorouridine (5'-dFUR) is presented for the first time. Biomethylation seems to occur specifically at the N3 site on the pyrimidine ring. This novel metabolic product was detected by gas chromatography-mass spectrometry of the trimethylsilylated extract of plasma samples from cancer patients undergoing doxifluridine chemotherapy. Considering the observed electron impact fragmentation pattern, the metabolic product was tentatively identified as N3-Me-5'-dFUR. Definite confirmation of the proposed structure was achieved by comparison of the mass spectra and chromatographic characteristics of the suspected metabolite with those of a synthetically prepared reference standard.

Purified halorhodopsin was isolated from Halobacterium halobium as previously described (Duschl, A. et al. (1988) J. Biol. Chem. 263, 17016-17022). Two purple bands were eluted from phenyl-Sepharose column, indicating the presence of differently retained halorhodopsin forms; the absorption spectra of the two halorhodopsin bands in the dark were not different. By gas chromatography/mass spectrometry we could identify palmitate (which is only a minor lipid component of archaeal cells) among lipids associated with purple fractions. Typically the palmitate content of the first eluted band was higher than that of the second, indicating a correlation between the palmitate content and the retention time; from one to two fatty acid molecules per halorhodopsin molecule were present depending on the fraction analysed. Very little or no palmitate was released from denatured halorhodopsin. By adding palmitate to buffers used in the phenyl-Sepharose chromatography, only one sharp purple band was collected, corresponding to the less retained halorhodopsin fraction. Pentadecanoic fatty acid could also affect the halorhodopsin chromatography. Chromatography of halorhodopsin in the presence of beta-mercaptoethanol showed only one band, corresponding to the more retrained halorhodopsin form. The two halorhodopsin fractions had different photoreactivity; the less retained halorhodopsin fraction (at higher palmitate content) showed an higher rate of decay of the absorbance at 570 nm upon illumination. By following the decay of the absorbance at 570 nm upon addition of alkali in the dark, we found that the two halorhodopsin fractions had different pKa values of deprotonation.

A microdialysis fibre based, low volume sampler is described which can be used in flow injection analysis (FIA) when an on-line dilution of the sample and/or removal of high molecular weight interferents is required. This device used in combination with a lactate amperometric biosensor based on lactate oxidase electrochemically immobilised in a bilayer membrane of poly(o-phenylendiamine) and overoxidized poly(pyrrole) permits the extension of the linear range of response up to 10 mM lactate. Combining microdialysis sampling with FIA and amperometric detection at an interference-free and fast-response biosensor, lactate determination in complex media such as serum, milk and yoghurt can be easily achieved with a high sample throughput and no sample pre-treatment.

A semi-automated solid-phase extraction procedure on-line with gradient elution reversed-phase chromatography permits the determination of lonidamine and its metabolite in human serum. The average recovery from serum at the 2.5 micrograms ml-1 level was (92.8 +/- 3.4)%. The limit of quantitation for a 100 microliter sample size was 50 ng ml-1. The within-day (n = 5) and between-day (n = 5) relative standard deviations for lonidamine determination in serum samples spiked at the 2.5 micrograms ml-1 level were 2.7% and 4.5%, respectively.

A simple, fast and precise method for the simultaneous determination of neopterine (Npt), pseudouridine (Psu) and creatinine (Cre) in urine by using ion-pair HPLC has been developed. The urine specimen is subjected to a microcolumn clean-up step, providing a ten-fold sample dilution, and is then injected into the column. The eluate is forced through the respective cells of a fluorescence and then a UV detector, which are connected in series. Neopterine is monitored by fluorescence emission at 438 nm (excitation wavelength 353 nm) while Psu and Cre are monitored by UV absorption at 235 nm. This allows the determination of Npt/Cre and Psu/Cre concentration ratios in a single run on the same sample, and the use of urine specimens collected randomly instead of 24 hourly collections. The method has been applied to urine specimens from 19 healthy, male donors (mean Npt/Cre (mumol/mol) and Psu/Cre (mumol/mmol) values of 41.7 and 16.8, respectively) and 23 healthy, female donors (mean Npt/Cre (mumol/mol) and Psu/Cre (mumol/mol) values of 67.4 and 18.5, respectively). The within-run S(r) for Npt/Cre and Psu/Cre concentration ratios ranged between 3.3 and 4.6%.

The electrochemical immobilization of lactate oxidase in a poly-o-phenylenediamine film permits the one-step and all-chemical construction of a lactate amperometric biosensor. The sensor was prepared in situ i.e. in the flow injection analysis (FIA) system by simply injecting a plug of a solution containing the monomer and the enzyme. At a flow rate of 50 microL/min linearity was observed up to 0.2 mM lactate and detection limits of about 2 microM could be easily achieved. Faradaic interferences caused by ascorbate, urate, cysteine and acetaminophen were sufficiently minimized to permit lactate determination in diluted serum by FIA. Results obtained by FIA-amperometric detection compared well (according to a proper t-test at a 95% confidence level) with those obtained by a standard enzymatic colorimetric assay. At a flow rate of 1 ml/min a sample throughput higher than 70 sample h-1 was achieved. After one week of continuous use in the FIA system a 75% decrease in biosensor sensitivity was observed.

A copper-modified strong cation exchange stationary phase was used for the solid phase extraction of the antineoplastic drug doxifluridine (5'-deoxy-5-fluorouridine) and some of its main metabolites from human serum. Sorption of fluoropyrimidine derivatives due to complex formation with copper(II) was maximal at pH values around neutrality. Analytes were eluted by ligand exchange with ammonia. The average recoveries ranged from 70% to 108%. Reversed-phase chromatography with ultraviolet detection was used for the separation and quantitation of the analytes. The overall procedure has been applied to serum samples from patients receiving doxifluridine chemotherapy, and a pharmacokinetic profile has been derived.

A selective method for the determination of altertoxin-I and altertoxin-II by high-performance liquid chromatography with electrochemical detection is described. Altertoxins were separated on a reversed-phase column with methanol-water containing 0.1 M sodium nitrate and 1 mM nitric acid (60:40) as eluent and detected with dual in-series electrodes operating in the "redox" mode (generator electrode +1.0 V, indicator electrode -0.1 V). The method was applied successfully to the determination of sub-ppm levels of altertoxins in samples of maize, rice and tomatoes infected by Alternaria alternata.

o-Phenylenediamine has been used for glucose oxidase (GOx) immobilization on Pt electrodes by electrochemical polymerization at +0.65 V vs SCE. By this approach the enzyme is entrapped in a strongly adherent, highly reproducible thin membrane, whose thickness is around 10 nm. This one-step procedure produces a glucose sensor with a response time less than 1 s, an active enzyme loading higher than 3 units/cm2 of electrode surface, a high sensitivity, and a sufficiently wide linear range. The glucose response shows an apparent Michaelis-Menten constant, K'm = 14.2 mM, and a limiting current density, jmax of 181 microA/cm2. The product kD of partition and diffusion coefficients of glucose in the polymer film is on the order of 10(-13) cm2/s. Due to permselectivity characteristics of the membrane, the access of ascorbate, a common interfering species, to the electrode surface is blocked. To our knowledge, this represents the first report of a membrane capable, at the same time, of immobilizing GOx and rejecting ascorbate. The interesting electrode behavior can be rationalized by using an existing model predicting the amperometric response of an immobilized GOx system.

Isoaltenuene, a previously unknownAlternaria metabolite has been isolated from a rice culture ofAlternaria alternata and purified by semipreparative HPLC. The assigned structure, elucidated by UV, IR, MS, and NMR spectroscopy, was 2', 3', 4', 5'-tetrahydro-3, 4'β, 5'α-trihydroxy-5-methoxy-2'α-methyldibenzo (α)-pyrone and corresponded to a diasteroisomer of altenuene with inverted configuration at C-2'. Isoaltenuene showed a minor phytotoxic activity on tomato leaves at level of 20 μg/spot and no antifungal activity onGeotrichum candidum (up to 20 μg/disk).

A simple procedure for the simultaneous determination of pseudouridine and creatinine in urine using ion-pair high-performance liquid chromatography with ultraviolet detection is described. It consists of simply diluting the filtered urine with mobile phase (1:20) followed by direct chromatographic injection. A single analysis takes only 10 min. This method has been applied to the analysis of urine samples from normal donors and patients with different types of cancer. The mean values, means, of the peak-area ratio of pseudouridine to creatinine were 61.79.10(-3) and 81.92.10(-3) for male and female normal donors, respectively. Out of twenty-five urine samples of patients with cancer examined, nineteen (all the forteen males included) had values higher than means + 2 sigma.

A fast and sensitive method for determination of the antineoplastic drug methotrexate in untreated serum and urine is described. Reversed-phase liquid chromatography with sodium dodecyl sulfate (SDS) micellar mobile phase has been used with direct sample injection. Changes in mobile phase variables such as SDS concentration and/or pH profoundly affected drug retention. Recovery was quantitative and the detection limit (90 nM for a 20 microL sample size) was below the range normally monitored. Multichannel UV detection provided strong evidence regarding peak purity and peak identity.

Allopurinol, oxipurinol and uric acid have been determined in human serum and urine by liquid chromatography with electrochemical detection. In particular the use of a polarographic detector operating in the oxidative mode, whose principle of detection is based on the property of allopurinol, oxipurinol and uric acid to form insoluble anodic films on mercury, is described. The performance of such a detector is compared with that of a glassy carbon wall-jet detector. Different procedures for sample pretreatment have been evaluated.

Some preliminary data concerning the anodic behaviour of the antineoplastic agent methotrexate are reported, and a high-performance liquid chromatographic method with electrochemical detection for its determination in human serum and urine is described. The method uses a reversed-phase C18 column and isocratic elution with amperometric detection on glassy carbon at +0.95 V vs. Ag/AgCl reference electrode. Sample treatment consists of a simple deproteinization step (serum) or an extraction procedure on Sep-Pak C18 cartridges (serum) or Amberlite column (urine). The detection limit for methotrexate in serum is 2.2 nmol/l. The method should prove useful for the evaluation of the drug pharmacokinetics in patients undergoing anticancer therapy.

The potential of high-performance liquid chromatography (HPLC) with diode-array detection for the profiling of mycotoxins in food samples has been demonstrated. A gradient elution reversed-phase chromatographic method coupled with a suitable extraction procedure was devised for the separation and detection of major Alternaria mycotoxins in foodstuffs. Altenuene, alternariol, alternariol methyl ether (dibenzo-alpha-pyrone derivatives), altertoxin-I and altertoxin-II (perylene derivatives) were profiled in extracts of artificially infected maize, rice and tomato samples and naturally contaminated sunflower seeds. First evidence of the occurrence of a new dibenzo-alpha-pyrone derivative in Alternaria cultures is also reported.