Search

Reconfigurable devices with field-effect transistor features and neuromorphic behaviors are promising for enhancing data processing capability and reducing power consumption in next-generation semiconductor platforms. However, commonly used 2D materials for reconfigurable devices require additional modulation terminals and suffer from complex and stringent operating rules to obtain specific functionalities. Here, a p-type disordered tellurium oxide is introduced that realizes dual-mode reconfigurability as a logic transistor and a neuromorphic device. Due to the disordered film surface, the enhanced adsorption of oxygen molecules and laser-induced desorption concurrently regulate the carrier concentration in the channel. The device exhibits high-performance p-type characteristics with a field-effect hole mobility of 10.02 cm 2 V -1 s -1 and an I on /I off ratio exceeding 10 6 in the transistor mode. As a neuromorphic device, the vision system exhibits biomimetic bee vision, explicitly responding to the blue-to-ultraviolet light. Finally, in-sensor denoising and invisible image recognition in static and dynamic scenarios are achieved., (© 2024 Wiley‐VCH GmbH.)

Brain-like intelligence is ushering humanity into an era of the Internet of Perceptions (IoP), where the vast amounts of data generated by numerous sensing nodes pose significant challenges to transmission bandwidth and computing hardware. A recently proposed near-sensor computing architecture offers an effective solution to reduce data processing delays and energy consumption. However, a pressing need remains for innovative hardware with multifunctional near-sensor image processing capabilities. In this work, Mott material (vanadium dioxide)-based photothermoelectric near-infrared photodetectors are developed that exhibit electrode-dependent and tunable super-linear photoresponse (exponent α > 33) with ultralow modulation bias. These devices demonstrate an opto-thermo-electro-coupled phase transition, resulting in a large photocurrent on/off ratio (>10 5 ), high responsivity (≈500 A W -1 ), and well detectivity (≈3.9 × 10 12 Jones), all while maintaining rapid response speeds (τ r = 2 µs and τ d = 5 µs) under the bias of 1 V. This electrode-dependent super-linear response is found to arise from the electron doping effect determined by the polarity of the Seebeck coefficient. Furthermore, the work showcases intensity-selective near-sensor processing and night vision pattern reorganization, even with noisy inputs. This work paves the way for developing near-sensor devices with potential applications in medical image preprocessing, flexible electronics, and intelligent edge sensing., (© 2024 Wiley‐VCH GmbH.)

Autophagy has gained importance in the context of ferroptosis. Nevertheless, a deeper understanding of the regulatory mechanism governing autophagy-dependent ferroptosis is necessary. Cytoglobin (CYGB), a member of the globin family, exhibits antifibrotic effects, regulates cellular reactive oxygen species, and stimulates tumor inhibition. Herein, we present further insights into the role of CYGB in ferroptosis regulation. Our investigation confirmed that CYGB impedes cell proliferation and migration. Furthermore, a significant association between CYGB and the lysosomal pathway was suggested based on the RNA sequencing data analysis. Elevated lysosomal signal and colocalization of CYGB with lysosome-associated membrane glycoprotein 1 (LAMP1) were observed. Moreover, upregulated autophagy and augmented ferroptosis induced by RSL3 were confirmed in CYGB-overexpression cells with an obviously increased colocalization of nuclear receptor coactivator 4 (NCOA4) and LC3B. The autophagy inhibitor bafilomycin or chloroquine alleviated autophagy-dependent degradation of ferritin protein under RSL3 treated condition. Additionally, a colocalization of CYGB with the transferrin receptor (TFR) was confirmed. Our results demonstrate an important functional pathway by which CYGB regulates ferroptosis through TFR-binding and autophagic degradation of ferritin, and provide a potential pathway for the treatment of colorectal cancer., Competing Interests: Declarations Conflicts of interest The authors declare no competing interests., (© 2024. The Author(s).)

As demand for higher integration density and smaller devices grows, silicon-based complementary metal-oxide-semiconductor (CMOS) devices will soon reach their ultimate limits. 2D transition metal dichalcogenides (TMDs) semiconductors, known for excellent electrical performance and stable atomic structure, are seen as promising materials for future integrated circuits. However, controlled and reliable doping of 2D TMDs, a key step for creating homogeneous CMOS logic components, remains a challenge. In this study, a continuous electrical polarity modulation of monolayer WS 2 from intrinsic n-type to ambipolar, then to p-type, and ultimately to a quasi-metallic state is achieved simply by introducing controllable amounts of vanadium (V) atoms into the WS 2 lattice as p-type dopants during chemical vapor deposition (CVD). The achievement of purely p-type field-effect transistors (FETs) is particularly noteworthy based on the 4.7 at% V-doped monolayer WS 2 , demonstrating a remarkable on/off current ratio of 10 5 . Expanding on this triumph, the first initial prototype of ultrathin homogeneous CMOS inverters based on monolayer WS 2 is being constructed. These outcomes validate the feasibility of constructing homogeneous CMOS devices through the atomic doping process of 2D materials, marking a significant milestone for the future development of integrated circuits., (© 2024 The Author(s). Small published by Wiley‐VCH GmbH.)

Wearable visual bionic devices, fueled by advancements in artificial intelligence, are making remarkable progress. However, traditional silicon vision chips often grapple with high energy losses and challenges in emulating complex biological behaviors. In this study, we constructed a van der Waals P3HT/GaAs nanowires P-N junction by carefully directing the arrangement of organic molecules. Combined with a Schottky junction, this facilitated multi-faceted birdlike visual enhancement, including broadband non-volatile storage, low-light perception, and a near-zero power consumption operating mode in both individual devices and 5 × 5 arrays on arbitrary substrates. Specifically, we realized over 5 bits of in-memory sensing and computing with both negative and positive photoconductivity. When paired with two imaging modes (visible and UV), our reservoir computing system demonstrated up to 94% accuracy for color recognition. It achieved motion and UV grayscale information extraction (displayed with sunscreen), leading to fusion visual imaging. This work provides a promising co-design of material and device for a broadband and highly biomimetic optoelectronic neuromorphic system., (© 2024. The Author(s).)

Inorganic semiconductors typically have limited p-type behavior due to the scarcity of holes and the localized valence band maximum, hindering the progress of complementary devices and circuits. In this work, we propose an inorganic blending strategy to activate the hole-transporting character in an inorganic semiconductor compound, namely tellurium-selenium-oxygen (TeSeO). By rationally combining intrinsic p-type semimetal, semiconductor, and wide-bandgap semiconductor into a single compound, the TeSeO system displays tunable bandgaps ranging from 0.7 to 2.2 eV. Wafer-scale ultrathin TeSeO films, which can be deposited at room temperature, display high hole field-effect mobility of 48.5 cm 2 /(Vs) and robust hole transport properties, facilitated by Te-Te (Se) portions and O-Te-O portions, respectively. The nanosphere lithography process is employed to create nanopatterned honeycomb TeSeO broadband photodetectors, demonstrating a high responsibility of 603 A/W, an ultrafast response of 5 μs, and superior mechanical flexibility. The p-type TeSeO system is highly adaptable, scalable, and reliable, which can address emerging technological needs that current semiconductor solutions may not fulfill., (© 2024. The Author(s).)

The treatment of hepatocellular carcinoma (HCC) is particularly challenging due to the inherent tumoral heterogeneity and easy resistance towards chemotherapy and immunotherapy. Arsenic trioxide (ATO) has emerged as a cytotoxic agent effective for treating solid tumors, including advanced HCC. However, its effectiveness in HCC treatment remains limited, and the underlying mechanisms are still uncertain. Therefore, this study aimed to characterize the effects and mechanisms of ATO in HCC. By evaluating the susceptibilities of human and murine HCC cell lines to ATO treatment, we discovered that HCC cells exhibited a range of sensitivity to ATO treatment, highlighting their inherent heterogeneity. A gene signature comprising 265 genes was identified to distinguish ATO-sensitive from ATO-insensitive cells. According to this signature, HCC patients have also been classified and exhibited differential features of ATO response. Our results showed that ATO treatment induced reactive oxygen species (ROS) accumulation and the activation of multiple cell death modalities, including necroptosis and ferroptosis, in ATO-sensitive HCC cells. Meanwhile, elevated tumoral immunogenicity was also observed in ATO-sensitive HCC cells. Similar effects were not observed in ATO-insensitive cells. We reported that ATO treatment induced mitochondrial injury and mtDNA release into the cytoplasm in ATO-sensitive HCC tumors. This subsequently activated the cGAS-STING-IFN axis, facilitating CD8 + T cell infiltration and activation. However, we found that the IFN pathway also induced tumoral PD-L1 expression, potentially antagonizing ATO-mediated immune attack. Additional anti-PD1 therapy promoted the anti-tumor response of ATO in ATO-sensitive HCC tumors. In summary, our data indicate that heterogeneous ATO responses exist in HCC tumors, and ATO treatment significantly induces immunogenic cell death (ICD) and activates the tumor-derived mtDNA-STING-IFN axis. These findings may offer a new perspective on the clinical treatment of HCC and warrant further study., (© 2024. The Author(s).)

Time-resolved or time-correlation measurements using cathodoluminescence (CL) reveal the electronic and optical properties of semiconductors, such as their carrier lifetimes, at the nanoscale. However, halide perovskites, which are promising optoelectronic materials, exhibit significantly different decay dynamics in their CL and photoluminescence (PL). We conducted time-correlation CL measurements of CsPbBr 3 using Hanbury Brown-Twiss interferometry and compared them with time-resolved PL. The measured CL decay time was on the order of subnanoseconds and was faster than PL decay at an excited carrier density of 2.1 × 10 18 cm -3 . Our experiment and analytical model revealed the CL dynamics induced by individual electron incidences, which are characterized by highly localized carrier generation followed by a rapid decrease in carrier density due to diffusion. This carrier diffusion can play a dominant role in the CL decay time for undoped semiconductors, in general, when the diffusion dynamics are faster than the carrier recombination.

Anti-ambipolar heterojunctions are vital in constructing high-frequency oscillators, fast switches, and multivalued logic (MVL) devices, which hold promising potential for next-generation integrated circuit chips and telecommunication technologies. Thanks to the strategic material design and device integration, anti-ambipolar heterojunctions have demonstrated unparalleled device and circuit performance that surpasses other semiconducting material systems. This review aims to provide a comprehensive summary of the achievements in the field of anti-ambipolar heterojunctions. First, the fundamental operating mechanisms of anti-ambipolar devices are discussed. After that, potential materials used in anti-ambipolar devices are discussed with particular attention to 2D-based, 1D-based, and organic-based heterojunctions. Next, the primary device applications employing anti-ambipolar heterojunctions, including anti-ambipolar transistors (AATs), photodetectors, frequency doublers, and synaptic devices, are summarized. Furthermore, alongside the advancements in individual devices, the practical integration of these devices at the circuit level, including topics such as MVL circuits, complex logic gates, and spiking neuron circuits, is also discussed. Lastly, the present key challenges and future research directions concerning anti-ambipolar heterojunctions and their applications are also emphasized., (© 2023 Wiley‐VCH GmbH.)

Nicotine exposure from smoking constitutes a significant global public health concern. Furthermore, smoking represents a pivotal risk factor for head and neck squamous cell carcinoma (HNSCC). However, the influence of nicotine on HNSCC remains relatively underexplored. Our aim was to unravel the molecular mechanisms that underlie the effect of nicotine on the metastatic cascade of HNSCC. In this study, we discovered a significant association between smoking and HNSCC metastasis and prognosis. Nicotine significantly enhanced HNSCC cell proliferation, migration, invasion, and epithelial-mesenchymal transition (EMT) in vitro. Analysis of TCGA-HNSCC and FDEENT-HNSCC cohorts revealed reduced miR-375-3p levels in HNSCC tumor tissues, particularly among current smokers. Additionally, miR-375-3p level was strongly correlated with both lymph node metastasis and tumor stage. By downregulating miR-375-3p, nicotine promotes HNSCC cell metastasis in vitro and hematogenous metastatic capacity in vivo. Utilizing transcriptomic sequencing, molecular docking, dual-luciferase reporter assay, and fluorescence in situ hybridization (FISH), we demonstrated that miR-375-3p specifically binds to 3' untranslated region (3'UTR) of NTRK2 mRNA. Thus, this study uncovers a novel nicotine-induced mechanism involving miR-375-3p-mediated NTRK2 targeting, which promotes HNSCC metastasis. These findings have implications for improving the prognosis of patients with HNSCC, especially in smokers., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Inc. All rights reserved.)

Benign and malignant classification of clustered microcalcifications (MCs) in digital breast tomosynthesis (DBT) is an essential task in computer-aided diagnosis. However, due to the anisotropic resolution of DBT, three-dimensional (3-D) convolutional neural network (CNN)-based methods cannot extract hierarchical features efficiently. Moreover, the sparse distribution of MC points in the cluster makes it difficult for the CNN to extract discriminative structural information for classification. To comprehensively address these challenges, we propose a novel structure-aware hierarchical network (SAH-Net) for benign and malignant classification of clustered MC in a DBT volume. Specifically, the two-dimensional (2-D) group convolution is used to extract intraslice features. The one-to-one correspondence between group convolutions and slices ensures the independence of hierarchical feature extraction. Then, a partial deformable Transformer-based 3-D structural feature learning module is proposed to capture the long-range dependency between MC points in the cluster. We evaluate the proposed method on an in-house dataset with 495 clustered MCs collected from 462 DBT images. Experimental results confirm the validity of our proposed modules. The results also show that the proposed SAH-Net outperforms several other representative methods on this topic, and achieves the best classification result, with an area under the receiver operation curve (AUC) of 86.87%. The implementation of the proposed model is available at https://github.com/sunhaotian130911/SAHNet.

Background: Breast cancer (BRCA) is a common malignancy in women, and its resistance to immunotherapy is a major challenge. Abnormal expression of genes is important in the occurrence and development of BRCA and may also affect the prognosis of patients. Although many BRCA prognosis model scores have been developed, they are only applicable to a limited number of disease subtypes. Our goal is to develop a new prognostic score that is more accurate and applicable to a wider range of BRCA patients., Methods: BRCA patient data from The Cancer Genome Atlas database was used to identify breast cancer-related genes (BRGs). Differential expression analysis of BRGs was performed using the 'limma' package in R. Prognostic BRGs were identified using co-expression and univariate Cox analysis. A predictive model of four BRGs was established using Cox regression and the LASSO algorithm. Model performance was evaluated using K-M survival and receiver operating characteristic curve analysis. The predictive ability of the signature in immune microenvironment and immunotherapy was investigated. In vitro experiments validated POLQ function., Results: Our study identified a four-BRG prognostic signature that outperformed conventional clinicopathological characteristics in predicting survival outcomes in BRCA patients. The signature effectively stratified BRCA patients into high- and low-risk groups and showed potential in predicting the response to immunotherapy. Notably, significant differences were observed in immune cell abundance between the two groups. In vitro experiments demonstrated that POLQ knockdown significantly reduced the viability, proliferation, and invasion capacity of MDA-MB-231 or HCC1806 cells., Conclusion: Our 4-BRG signature has the potential as an independent biomarker for predicting prognosis and treatment response in BRCA patients, complementing existing clinicopathological characteristics., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2024 Chen, Kang, Sheng, Huang, Cheng, Pei and Meng.)

High synthesis temperatures and specific growth substrates are typically required to obtain crystalline or oriented inorganic functional thin films, posing a significant challenge for their utilization in large-scale, low-cost (opto-)electronic applications on conventional flexible substrates. Here, we explore a pulse irradiation synthesis (PIS) to prepare thermoelectric metal chalcogenide (e.g., Bi 2 Se 3 , SnSe 2 , and Bi 2 Te 3 ) films on multiple polymeric substrates. The self-propagating combustion process enables PIS to achieve a synthesis temperature as low as 150 °C, with an ultrafast reaction completed within one second. Beyond the photothermoelectric (PTE) property, the thermal coupling between polymeric substrates and bismuth selenide films is also examined to enhance the PTE performance, resulting in a responsivity of 71.9 V/W and a response time of less than 50 ms at 1550 nm, surpassing most of its counterparts. This PIS platform offers a promising route for realizing flexible PTE or thermoelectric devices in an energy-, time-, and cost-efficient manner., (© 2024. The Author(s).)

The demand for economical and efficient data processing has led to a surge of interest in neuromorphic computing based on emerging two-dimensional (2D) materials in recent years. As a rising van der Waals (vdW) p-type Weyl semiconductor with many intriguing properties, tellurium (Te) has been widely used in advanced electronics/optoelectronics. However, its application in floating gate (FG) memory devices for information processing has never been explored. Herein, an electronic/optoelectronic FG memory device enabled by Te-based 2D vdW heterostructure for multimodal reservoir computing (RC) is reported. When subjected to intense electrical/optical stimuli, the device exhibits impressive nonvolatile electronic memory behaviors including ≈10 8 extinction ratio, ≈100 ns switching speed, >4000 cycles, >4000-s retention stability, and nonvolatile multibit optoelectronic programmable characteristics. When the input stimuli weaken, the nonvolatile memory degrades into volatile memory. Leveraging these rich nonlinear dynamics, a multimodal RC system with high recognition accuracy of 90.77% for event-type multimodal handwritten digit-recognition is demonstrated., (© 2023 The Authors. Advanced Materials published by Wiley-VCH GmbH.)

Growing high-quality core-shell heterostructure nanowires is still challenging due to the lattice mismatch issue at the radial interface. Herein, a versatile strategy is exploited for the lattice-mismatch-free construction of III-V/chalcogenide core-shell heterostructure nanowires by simply utilizing the surfactant and amorphous natures of chalcogenide semiconductors. Specifically, a variety of III-V/chalcogenide core-shell heterostructure nanowires are successfully constructed with controlled shell thicknesses, compositions, and smooth surfaces. Due to the conformal properties of obtained heterostructure nanowires, the wavelength-dependent bi-directional photoresponse and visible light-assisted infrared photodetection are realized in the type-I GaSb/GeS core-shell heterostructure nanowires. Also, the enhanced infrared photodetection is found in the type-II InGaAs/GeS core-shell heterostructure nanowires compared with the pristine InGaAs nanowires, in which both responsivity and detectivity are improved by more than 2 orders of magnitude. Evidently, this work paves the way for the lattice-mismatch-free construction of core-shell heterostructure nanowires by chemical vapor deposition for next-generation high-performance nanowire optoelectronics., (© 2023. The Author(s).)

All-inorganic lead halide perovskites (CsPbX 3 , X = Cl, Br or I) are becoming increasingly important for energy conversion and optoelectronics because of their outstanding performance and enhanced environmental stability. Morphing perovskites into specific shapes and geometries without damaging their intrinsic functional properties is attractive for designing devices and manufacturing. However, inorganic semiconductors are often intrinsically brittle at room temperature, except for some recently reported layered or van der Waals semiconductors. Here, by in situ compression, we demonstrate that single-crystal CsPbX 3 micropillars can be substantially morphed into distinct shapes (cubic, L and Z shapes, rectangular arches and so on) without localized cleavage or cracks. Such exceptional plasticity is enabled by successive slips of partial dislocations on multiple [Formula: see text] systems, as evidenced by atomic-resolution transmission electron microscopy and first-principles and atomistic simulations. The optoelectronic performance and bandgap of the devices were unchanged. Thus, our results suggest that CsPbX 3 perovskites, as potential deformable inorganic semiconductors, may have profound implications for the manufacture of advanced optoelectronics and energy systems., (© 2023. The Author(s), under exclusive licence to Springer Nature Limited.)

The purpose of this study is to test the feasibility for deep CNN-based artificial intelligence methods for automatic classification of the mass margin and shape, while radiomic feature-based machine learning methods were also implemented in this study as baseline and for comparison study. In this retrospective study, 596 patients with breast mass that underwent mammography from 4 hospitals were enrolled from January 2012 to October 2019. Margin and shape of each mass were annotated according to BI-RADS by 2 experienced radiologists. Deep CNN-based AI was implemented for the classification task based on Resnet50. Balanced sampler and CBAM were also used to improve the performance of the Deep CNNs. As comparison, image texture features were extracted and then dimensionality reduction methods (such as PCA, ICA) and classical classifiers (such as SVM, DT, KNN) were used for classification task. Based on Python programming software, accuracy (ACC) was used to evaluate the performance of the model, and the model with the highest ACC value was selected. Deep CNN based on Resnet50 with balanced sampler and CBAM achieved the best performance for both margin and shape classification, with ACC of 0.838 and 0.874, respectively. For the radiomics-based machine learning, the best performance for margin was achieved as 0.676 by the combination of FA + RF, while the best performance for shape was 0.802 by the combination of PCA + MLP. The feasibility for automatic classification with coarse labeling of the mass shape and margin was testified with the deep CNN-based AI methods, while radiomic feature-based machine learning methods achieved inferior classification results., (© 2023. The Author(s) under exclusive licence to Society for Imaging Informatics in Medicine.)

Chemical bonds, including covalent and ionic bonds, endow semiconductors with stable electronic configurations but also impose constraints on their synthesis and lattice-mismatched heteroepitaxy. Here, the unique multi-scale van der Waals (vdWs) interactions are explored in one-dimensional tellurium (Te) systems to overcome these restrictions, enabled by the vdWs bonds between Te atomic chains and the spontaneous misfit relaxation at quasi-vdWs interfaces. Wafer-scale Te vdWs nanomeshes composed of self-welding Te nanowires are laterally vapor grown on arbitrary surfaces at a low temperature of 100 °C, bringing greater integration freedoms for enhanced device functionality and broad applicability. The prepared Te vdWs nanomeshes can be patterned at the microscale and exhibit high field-effect hole mobility of 145 cm 2 /Vs, ultrafast photoresponse below 3 μs in paper-based infrared photodetectors, as well as controllable electronic structure in mixed-dimensional heterojunctions. All these device metrics of Te vdWs nanomesh electronics are promising to meet emerging technological demands., (© 2023. The Author(s).)

Atomically 2D layered ferroelectric semiconductors, in which the polarization switching process occurs within the channel material itself, offer a new material platform that can drive electronic components toward structural simplification and high-density integration. Here, a room-temperature 2D layered ferroelectric semiconductor, bismuth oxychalcogenides (Bi 2 O 2 Se), is investigated with a thickness down to 7.3 nm (≈12 layers) and piezoelectric coefficient (d 33 ) of 4.4 ± 0.1 pm V -1 . The random orientations and electrically dependent polarization of the dipoles in Bi 2 O 2 Se are separately uncovered owing to the structural symmetry-breaking at room temperature. Specifically, the interplay between ferroelectricity and semiconducting characteristics of Bi 2 O 2 Se is explored on device-level operation, revealing the hysteresis behavior and memory window (MW) formation. Leveraging the ferroelectric polarization originating from Bi 2 O 2 Se, the fabricated device exhibits "smart" photoresponse tunability and excellent electronic characteristics, e.g., a high on/off current ratio > 10 4 and a large MW to the sweeping range of 47% at V GS  = ±5 V. These results demonstrate the synergistic combination of ferroelectricity with semiconducting characteristics in Bi 2 O 2 Se, laying the foundation for integrating sensing, logic, and memory functions into a single material system that can overcome the bottlenecks in von Neumann architecture., (© 2023 Wiley-VCH GmbH.)

Converting vapor precursors to solid nanostructures via a liquid noble-metal seed is a common vapor deposition principle. However, such a noble-metal-seeded process is excluded from the crystalline halide perovskite synthesis, mainly hindered by the growth mechanism shortness. Herein, powered by a spontaneous exothermic nucleation process (Δ H < 0), the Au-seeded CsPbI 3 nanowires (NWs) growth is realized based on a vapor-liquid-solid (VLS) growth mode. It is energetically favored that the Au seeds are reacted with a Pb vapor precursor to form molten Au-Pb droplets at temperatures down to 212 °C, further triggering the low-temperature VLS growth of CsPbI 3 NWs. More importantly, this Au-seeded process reduces in-bandgap trap states and consequently avoids Shockley-Read-Hall recombination, contributing to outstanding photodetector performances. Our work extends the powerful Au-seeded VLS growth mode to the emerging halide perovskites, which will facilitate their nanostructures with tailored material properties.

Breast tumor segmentation plays a critical role in the diagnosis and treatment of breast diseases. Current breast tumor segmentation methods are mainly deep learning (DL) based methods, which exacted the contrast information between tumors and backgrounds, and produced tumor candidates. However, all these methods were developed based on traditional standard convolutions, which may not be able to model various tumor shapes and extract pure information of tumors (the extracted information usually contain non-tumor information). Besides, the loss functions used in these methods mainly aimed to minimize the intra-class distances, while ignoring the influence of inter-class distances upon segmentation. In this paper, we propose a novel lesion morphology aware network to segment breast tumors in 2D magnetic resonance images (MRI). The proposed network employs a hierarchical structure that contains two stages: breast segmentation stage and tumor segmentation stage. In the tumor segmentation stage, we devise a tumor morphology aware network to incorporate pure tumor characteristics, which facilitates contrastive information extraction. Further, we propose a hybrid intra- and inter-class distance optimization loss to supervise the network, which can minimize intra-class distances meanwhile maximizing inter-class distances, hence reducing the potential false positive/negative pixels in segmentation results. Verified on a clinical 2D MRI breast tumor dataset, our proposed method achieves eminent segmentation results and outperforms state-of-the-art methods, implying that the proposed method has a good prospect for clinical use., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

Objective: We used bioinformatics analysis to identify potential biomarker genes and their relationship with breast cancer (BC)., Materials and Methods: We used a weighted gene co-expression network analysis (WGCNA) to create a co-expression network based on the top 25% genes in the GSE24124, GSE33926, and GSE86166 datasets obtained from the Gene Expression Omnibus. We used the DAVID online platform to perform GO and KEGG pathway enrichment analyses and the Cytoscape CytoHubba plug-in to screen the potential genes. Then, we related the genes to prognostic values in BC using the Oncomine, GEPIA, and Kaplan-Meier Plotter databases. Findings were validated by immunohistochemical (IHC) staining in the Human Protein Atlas and the TCGA-BRCA cohort. LinkedOmics identified the interactive expressions of hub genes. We used UALCAN to evaluate the methylation levels of these hub genes. MethSurv and SurvivalMeth were used to assess the multilevel prognostic value. Finally, we assessed hub gene association with immune cell infiltration using TIMER., Results: The mRNA levels of MKI67, UBE2C, GTSE1, CCNA2, and MND1 were significantly upregulated in BC, whereas ESR1, THSD4, TFF1, AGR2, and FOXA1 were significantly downregulated. The DNA methylation signature analysis showed a better prognosis in the low-risk group. Further subgroup analyses revealed that MND1 might serve as an independent risk factor for unfavorable BC prognosis. Additionally, MND1 expression levels positively correlate with the immune infiltration statuses of CD4+ T cells, CD8+ T cells, B cells, neutrophils, dendritic cells, and macrophages., Conclusion: Our results indicate that the ten hub genes may be involved in BC's carcinogenesis, development, or metastasis, and MND1 may be a potential biomarker and therapeutic target for BC., Competing Interests: The authors have no conflicts of interest to declare., (© 2022 Bao et al.)

Background: Primary small cell breast carcinoma (SCBC) is an uncommon malignancy with highly invasive behavior. The aim of this study was to find out more about the incidence, clinicopathologic characteristics and identify potential prognostic factors of SCBC., Methods: Data of patients with primary diagnosis of SCBC between 1975 and 2018 were extracted from the Surveillance, Epidemiology, and End Results (SEER) database. The incidence after adjustment for age and percentage change per year in incidence were calculated. Disease-specific survival (DSS) and overall survival (OS) were analyzed among these SCBC patients identified from the SEER database. The whole cohorts were randomized into training and validation cohorts as ratio of 7: 3. Cox regression analysis was performed to determine predictors of survival with the training cohorts. Predictive models were constructed with training cohorts, and nomogram validation was performed using receiver operating characteristic curves, concordance indices and calibration curves in both training and validation cohorts., Results: 323 SCBC patients were enrolled finally during the research period. The overall incidence after adjustment for age between 1990 and 2018 was 0.14 per million per year, and the prevalence of the incidence has plateaued. Most of these tumors were poorly differentiated or undifferentiated. The most prevalent presenting stage was Stage II. Patients identified in this study were randomly divided into training (n = 226) and testing (n = 97) cohorts. Multivariate Cox proportional hazards model showed that chemotherapy, surgery and stage were important predictors of DSS and OS., Conclusion: SCBC is considered an infrequent breast neoplasm with aggressive characteristics. Tumor stage is associated with poor prognosis. Combination of surgery and chemotherapy is the main treatment for SCBC., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2022 Zhu, Wu, Zhao, Yang, Chen, Jiang, Meng, Ji and Gu.)

The performances of rechargeable batteries are strongly affected by the operating environmental temperature. In particular, low temperatures (e.g., ≤0 °C) are detrimental to efficient cell cycling. To circumvent this issue, we propose a few-layer Bi 2 Se 3 (a topological insulator) as cathode material for Zn metal batteries. When the few-layer Bi 2 Se 3 is used in combination with an anti-freeze hydrogel electrolyte, the capacity delivered by the cell at -20 °C and 1 A g -1 is 1.3 larger than the capacity at 25 °C for the same specific current. Also, at 0 °C the Zn | |few-layer Bi 2 Se 3 cell shows capacity retention of 94.6% after 2000 cycles at 1 A g -1 . This behaviour is related to the fact that the Zn-ion uptake in the few-layer Bi 2 Se 3 is higher at low temperatures, e.g., almost four Zn 2+ at 25 °C and six Zn 2+ at -20 °C. We demonstrate that the unusual performance improvements at low temperatures are only achievable with the few-layer Bi 2 Se 3 rather than bulk Bi 2 Se 3 . We also show that the favourable low-temperature conductivity and ion diffusion capability of few-layer Bi 2 Se 3 are linked with the presence of topological surface states and weaker lattice vibrations, respectively., (© 2022. The Author(s).)

Weyl semimetals (WSMs) with high electrical conductivity and suitable carrier density near the Fermi level are enticing candidates for aqueous Zn-ion batteries (AZIBs), meriting from topological surface states (TSSs). We propose a WSM Co 3 Sn 2 S 2 cathode for AZIBs showing a discharge plateau around 1.5 V. By introducing Sn vacancies, extra redox peaks from the Sn 4+ /Sn 2+ transition appear, which leads to more Zn 2+ transfer channels and active sites promoting charge-storage kinetics and Zn 2+ storage capability. Co 3 Sn 1.8 S 2 achieves a specific energy of 305 Wh kg -1 (0.2 Ag -1 ) and a specific power of 4900 Wkg -1 (5 Ag -1 ). Co 3 Sn 1.8 S 2 and Zn x Co 3 Sn 1.8 S 2 benefit from better conductivity at lower temperatures; the quasi-solid Co 3 Sn 1.8 S 2 //Zn battery delivers 126 mAh g -1 (0.6 Ag -1 ) at -30 °C and a cycling stability over 3000 cycles (2 Ag -1 ) with 85 % capacity retention at -10 °C., (© 2021 Wiley-VCH GmbH.)

Due to their unique properties, ZnO nanostructures have received considerable attention for application in electronics and optoelectronics; however, intrinsic ZnO nanomaterials usually suffer from large concentrations of lattice defects, such as oxygen vacancies, which restricts their material performance. Here, for the first time, highly-crystalline In and Ga co-doped ZnO nanowires (NWs) are achieved by ambient-pressure chemical vapor deposition. In contrast to conventional elemental doping, this In and Ga co-doping can not only enhance the carrier concentration, but also suppresses the formation of oxygen vacancies within the host lattice of ZnO NWs. Importantly, this co-doping is also believed to effectively minimize the generation of lattice strain defects due to the optimal ionic sizes of both In and Ga dopants. When configured into field-effect transistors (FETs), these co-doped NWs exhibit an enhanced average electron mobility of 315 cm 2 V -1 s -1 and an impressive on/off current ratio of 1.87 × 10 8 , which are already higher than those of other previously reported ZnO NW devices. In addition, these NW devices demonstrate efficient ultraviolet photodetection at under 261 nm irradiation with an improved responsivity of 1.41 × 10 7 A W -1 , an excellent EQE of up to 6.72 × 10 9 and a fast response time down to 0.32 s. Highly-ordered NW parallel array thin-film transistors and photodetectors are also constructed to demonstrate the promising potential of the NWs for high-performance device applications.

Sinomenine (SN) has been used in the clinical treatment of systemic lupus erythematosus and rheumatoid arthritis for many years. Studies showed that SN held protective effects such as anti-inflammation, scavenging free radicals and suppressing immune response in many autoimmune diseases. The purpose of the present study is to explore the mechanism of anti-inflammation of SN on lipopolysaccharide (LPS)-induced macrophages activation and investigate whether the TLR4/NF-κB signaling pathway participated in. Macrophages isolated from mouse peritoneal cavity were stimulated by 1 µg/mL LPS for 24 h. And then the cells were treated with various concentrations of SN, TLR4 inhibitor respectively for additional 48 h. Drug toxicity was detected by MTT assay and Transwell experiment was used to assess chemotaxis. Furthermore, TLR4 and MyD88 mRNA levels were detected by real-time PCR. Western blotting was used to examine TLR4, MyD88 and phosphorylated IκB protein expression in macrophages. Immunofluorescence assay was applied to observe p65 NF-κB protein expression in macrophage nucleus. We extracted macrophages with high purity and activity from the abdominal cavity of mice. SN remarkably inhibited the chemotaxis and secretion function of LPS-stimulated macrophages. It also down-regulated both the protein levels of inflammatory cytokines (TNF-α, IL-1β and IL-6) and the RNA and protein levels of the key factors (TLR4, MyD88, P-IκB) in TLR4 pathway. The expression of p65 NF-κB protein in nuclei was down-regulated, which was correlated with a similar decrease in P-IκB protein level. In conclusion, SN can inhibit the LPS induced immune responses in macrophages by blocking the activated TLR4/NF-κB signaling pathway. These results may provide a therapeutic approach to regulate inflammatory responses.

Despite the recent advances in electrochemical water splitting, developing cost-effective and highly efficient electrocatalysts for oxygen evolution reaction (OER) still remains a substantial challenge. Herein, two-dimensional cobalt phosphate hydroxides (Co 5 (PO 4 ) 2 (OH) 4 ) nanosheets, a unique stacking-disordered phosphate-based inorganic material, are successfully prepared via a facile and scalable method for the first time to serve as a superior and robust electrocatalyst for water oxidation. On the basis of the detailed characterization (e.g., X-ray absorption near-edge structure and X-ray photoelectron spectroscopy), the obtained nanosheets consist of special zigzag CoO 6 octahedral chains along with intrinsic lattice distortion and excellent hydrophilicity, in which these factors contribute to the highly efficient performance of prepared electrocatalysts for OER. Specifically, Co 5 (PO 4 ) 2 (OH) 4 deposited on glassy carbon electrode (loading amount ≈0.553 mg cm -2 ) can exhibit an unprecedented overpotential of 254 mV to drive a current density of 10 mA cm -2 with a small Tafel slope of 57 mV dec -1 in alkaline electrolytes, which outperforms the ones of CO 3 (PO 4 ) 2 (370 mV) and Co(OH) 2 (360 mV) as well as other advanced catalysts. Evidently, this work has opened a new pathway to the rational design of promising metal phosphate hydroxides toward the efficient electrochemical energy conversion.

Due to the efficient photocarrier separation and collection coming from their distinctive band structures, superlattice nanowires (NWs) have great potential as active materials for high-performance optoelectronic devices. In this work, InGaZnO NWs with superlattice structure and controllable stoichiometry are obtained by ambient-pressure chemical vapor deposition. Along the NW axial direction, perfect alternately stacking of InGaO(ZnO) 4 + blocks and InO 2 - layers is observed to form a periodic layered structure. Strikingly, when configured into individual NW photodetectors, the Ga concentration is found to significantly influence the amount of oxygen vacancies and oxygen molecules adsorbed on the NW surface, which dictate the photoconducting properties of the NW channels. Based on the optimized Ga concentration ( i.e ., In 1.8 Ga 1.8 Zn 2.4 O 7 ), the individual NW device exhibits an excellent responsivity of 1.95 × 10 5 A/W and external quantum efficiency of as high as 9.28 × 10 7 % together with a rise time of 0.93 s and a decay time of 0.2 s for the ultraviolet (UV) photodetection. Besides, the obtained NWs can be fabricated into large-scale parallel arrays on glass substrates as well to achieve fully transparent UV photodetectors, where the performance is on the same level or even better than many transparent photodetectors with high performance. All the results discussed above demonstrate the great potential of InGaZnO superlattice NWs for next-generation advanced optoelectronic devices.

Because of their fascinating properties, two-dimensional (2D) nanomaterials have attracted a lot of attention for developing next-generation electronics and optoelectronics. However, there is still a lack of cost-effective, highly reproducible, and controllable synthesis methods for developing high-quality semiconducting 2D monolayers with a sufficiently large single-domain size. Here, utilizing a NaOH promoter and W foils as the W source, we have successfully achieved the fabrication of ultralarge single-domain monolayer WS 2 films via a modified chemical vapor deposition method. With the proper introduction of a NaOH promoter, the single-domain size of monolayer WS 2 can be increased to 550 μm, while the WS 2 flakes can be well controlled by simply varying the growth duration and oxygen concentration in the carrier gas. Importantly, when they are fabricated into global backgated transistors, WS 2 devices exhibit respectable peak electron mobility up to 1.21 cm 2 V -1 s -1 , which is comparable to those of many state-of-the-art WS 2 transistors. Photodetectors based on these single-domain WS 2 monolayers give an impressive photodetection performance with a maximum responsivity of 3.2 mA W -1 . All these findings do not only provide a cost-effective platform for the synthesis of high-quality large single-domain 2D nanomaterials, but also facilitate their excellent intrinsic material properties for the next-generation electronic and optoelectronic devices.

Neoadjuvant chemoradiotherapy (nCRT) has been widely applied to improve the local control rate and survival rate in patients with locally advanced rectal cancer (LARC), yet only part of LARC patients would benefit from nCRT. Therefore, it is imperative to predict the therapeutic outcome of nCRT. Here, we showed that RAD18, an E3 ubiquitin-linked enzyme, played a fundamental role in predicting the response of LARC patients to nCRT. According to clinical data, patients with low RAD18 expression level in their pre-nCRT biopsies had a superior response to nCRT compared to those with high RAD18 expression. Inhibition of RAD18 expression in rectal cancer cells pronouncedly attenuated the proliferation and promoted apoptosis after exposing to irradiation or/and 5-fluorouracil (5-Fu). Downregulated RAD18 levels increased cell apoptosis by activating caspase-9-caspase-3-mediated apoptotic pathway, thus resulting in the enhancement of cell radiosensitivity and 5-Fu susceptibility. Furthermore, a xenograft nude mouse model showed that silencing RAD18 significantly slowed tumor growth after irradiation or/and 5-Fu in vivo. Collectively, these results implied that RAD18 could be a new biomarker to predict LARC patients who might benefit from nCRT and provide new strategies for clinical treatment of LARC., (© 2019 The Authors. Cancer Medicine published by John Wiley & Sons Ltd.)

Group III oxides, such as In 2 O 3 and Ga 2 O 3 , have proved to be good candidates as active materials for novel electronic devices, including high-mobility transistors, gas sensors, and UV photodetectors. The ability to tune optical and electronic properties is provided by alloying In 2 x Ga 2-2 x O 3 (InGaO) in a broad compositional range. Further development of InGaO compounds in the form of nanowires (NWs) would overcome the technological limitations, such as the substrate crystal lattice mismatch and the inability to fabricate high quality structures above the critical thickness. In this work, optical properties of alloyed InGaO NWs in a wide compositional range are carefully assessed. Unlike classical optical characterization methods, photoacoustic spectroscopy reveals the fundamental absorption edge despite the strong light scattering in porous and randomly oriented nanowires structure. An unusual compositional band gap dependence is also observed, giving insight into the phase segregation effect and increased quality of mixed NWs. In addition, photoacoustic measurements disclose potential applications of InGaO NWs in remote, light-driven loudspeakers because of intense photoacoustic effect in nanowire ensembles in this material system.

Controlled synthesis of lead halide perovskite (LHP) nanostructures not only benefits fundamental research but also offers promise for applications. Among many synthesis techniques, although catalytic vapor-liquid-solid (VLS) growth is recognized as an effective route to achieve high-quality nanostructures, until now, there is no detailed report on VLS grown LHP nanomaterials due to the emerging challenges in perovskite synthesis. Here, we develop a direct VLS growth for single-crystalline all-inorganic lead halide perovskite ( i.e., CsPbX 3 ; X = Cl, Br, or I) nanowires (NWs). These NWs exhibit high-performance photodetection with the responsivity exceeding 4489 A/W and detectivity over 7.9 × 10 12 Jones toward the visible light regime. Field-effect transistors (FET) based on individual CsPbX 3 NWs are also fabricated, where they show the superior hole mobility of up to 3.05 cm 2 /(V s), higher than other all-inorganic LHP devices. This work provides important guidelines for the further improvement of these perovskite nanostructures for utilizations.

Purpose: To perform contrast analysis of the relationship between high-resolution computed tomography (HRCT) signs and new pathologic classification of small GGNs-like lung adenocarcinoma., Materials and Methods: The HRCT data from 145 pathologically confirmed cases of small GGNs of lung adenocarcinoma were analysed retrospectively. The 145 cases of GGNs were divided into pre-invasive (PI) group (n = 46), micro-invasive adenocarcinoma (MIA) group (n = 48), and invasive adenocarcinoma (IAC) group (n = 51). HRCT imaging sign of GGNs in each group was assessed and compared., Results: Significant differences in GGN size were found among the three groups (P < 0.05). The presence of a tumour-lung interface in the MIA and IAC groups was significantly higher than that in the PI group (P < 0.05), but no significant difference was found between the MIA and IAC groups. The presence of a pleural indentation sign in the IAC group was significantly higher than that in the other two groups (P < 0.05), but no significant difference was noted between the latter two groups. Significant differences were found in the lobulated and spicule signs among the three groups (P < 0.05). The presence of a microvascular sign in the MIA and IAC groups was significantly higher than that in the PI group (P < 0.05). No significant difference was found in the GGN density, vacuole sign, air bronchus sign and notch sign among the three groups., Conclusions: The HRCT signs of GGNs could be used to differentiate among pre-invasive lesions, micro-invasive lesions and invasive lung adenocarcinoma.

Recently, metal oxide nanofibers fabricated by electrospinning have been considered as promising components for next-generation electronic devices. Unfortunately, the nanofiber-based electronic devices usually exhibited inferior electrical performance, due to the high contact resistance between the nanofibers and the inferior interfacial adhesion between the nanofibers and the substrate. In this report, an amine-hardened epoxy resin was selected as an adhesion agent to weld nanofiber junctions and improve the interfacial adhesion performance. It was confirmed that the physical properties of the nanofibers were greatly improved after the crosslinking welding process. Taking advantage of the welding process, field-effect transistors (FETs) based on In 2 O 3 nanofiber networks (NFNs) with various nanofiber densities were integrated and investigated. It was found that the FETs based on In 2 O 3 NFNs with a nanofiber density of 0.4 μm -1 exhibited the optimal electrical performance. When high-k ZrO x was integrated into the FETs as the dielectric layer, the FETs based on In 2 O 3 NFNs/ZrO x exhibited superior performance, including a μ FE of 13.2 cm 2 V -1 s -1 , an I on /I off of 10 7 , and an SS of 90 mV per decade. The crosslinking welding process is a simple, versatile and low-cost technique, which has great possibility for various applications.

One-dimensional metal-oxide nanowires are regarded as important building blocks in nanoscale electronics, because of their unique mechanical and electrical properties. In this work, p-type nickel oxide nanowires (NiO NWs) were fabricated by combining sol-gel and electrospinning processes. The poly(vinylpyrrolidone) (PVP) with a molecular weight of 1 300 000 was used as the polymer matrix to increase the viscosity of a NiO precursor solution. The formation and properties of the as-spun NiO/PVP composite NWs before/after calcination treatment were investigated using various techniques. Because of the enhanced adhesion properties between ultraviolet (UV)-treated NiO NWs and the substrate, the field-effect transistors (FETs) based on NiO NWs were found to exhibit satisfying p-channel behaviors. For the fabrication of aligned NiO NW arrays, two parallel conducting Si strips were grounded as NW collector. The integrated FETs based on aligned NiO NWs were demonstrated to exhibit superior electrical performance, compared to the disordered counterparts with the comparable NW coverage. By employing high- k aluminum oxide (Al 2 O 3 ) as a dielectric layer, instead of conventional SiO 2 , the devices with an aligned NiO NW array exhibit a high hole mobility of 2.8 cm 2 /(V s) with a low operating voltage of 5 V, fast switching speed, and successful modulation of light emission over external light-emitting diodes. To the best of our knowledge, this is the first work demonstrating the low-voltage transistors based on p-type oxide NWs, which represents a great step toward the development of sensors and CMOS logic circuits.

One-dimensional (1D) nanofibers have been considered to be important building blocks for nano-electronics due to their superior physical and chemical properties. In this report, high-performance zinc tin oxide (ZnSnO) nanofibers with various composition ratios were prepared by electrospinning. The surface morphology, crystallinity, grain size distribution, and chemical composition of the nanofibers were investigated. Meanwhile, field-effect transistors (FETs) based on ZnSnO nanofiber networks (NFNs) with various composition ratios were integrated and investigated. For optimized Zn0.3Sn0.7O NFNs FETs, the device based on an SiO2 dielectric exhibited a high electrical performance, including a high on/off current ratio (Ion/off) of 2 × 107 and a field-effect mobility (μFE) of 0.17 cm2 V-1 s-1. When a high-permittivity (κ) ZrOx thin film was employed as the dielectric in Zn0.3Sn0.7O NFNs FETs, the operating voltage was substantially reduced and a high μFE of 7.8 cm2 V-1 s-1 was achieved. These results indicate that the Zn0.3Sn0.7O NFNs/ZrOx FETs exhibit great potency in low-cost and low-voltage devices.

Recently, semiconducting nanofiber networks (NFNs) have been considered as one of the most promising platforms for large-area and low-cost electronics applications. However, the high contact resistance among stacking nanofibers remained to be a major challenge, leading to poor device performance and parasitic energy consumption. In this report, a controllable welding technique for NFNs was successfully demonstrated via a bioinspired capillary-driven process. The interfiber connections were well-achieved via a cooperative concept, combining localized capillary condensation and curvature-induced surface diffusion. With the improvements of the interfiber connections, the welded NFNs exhibited enhanced mechanical property and high electrical performance. The field-effect transistors (FETs) based on the welded Hf-doped In 2 O 3 (InHfO) NFNs were demonstrated for the first time. Meanwhile, the mechanisms involved in the grain-boundary modulation for polycrystalline metal-oxide nanofibers were discussed. When the high-k ZrO x dielectric thin films were integrated into the FETs, the field-effect mobility and operating voltage were further improved to be 25 cm 2 V -1 s -1 and 3 V, respectively. This is one of the best device performances among the reported nanofibers-based FETs. These results demonstrated the potencies of the capillary-driven welding process and grain-boundary modulation mechanism for metal-oxide NFNs, which could be applicable for high-performance, large-scale, and low-power functional electronics.

Technical development for thin-film fabrication is essential for emerging metal-oxide (MO) electronics. Although impressive progress has been achieved in fabricating MO thin films, the challenges still remain. Here, we report a versatile and general thermal-induced nanomelting technique for fabricating MO thin films from the fiber networks, briefly called fiber-to-film (FTF) process. The high quality of the FTF-processed MO thin films was confirmed by various investigations. The FTF process is generally applicable to numerous technologically relevant MO thin films, including semiconducting thin films (e.g., In 2 O 3 , InZnO, and InZrZnO), conducting thin films (e.g., InSnO), and insulating thin films (e.g., AlO x ). By optimizing the fabrication process, In 2 O 3 /AlO x thin-film transistors (TFTs) were successfully integrated by fully FTF processes. High-performance TFT was achieved with an average mobility of ∼25 cm 2 /(Vs), an on/off current ratio of ∼10 7 , a threshold voltage of ∼1 V, and a device yield of 100%. As a proof of concept, one-transistor-driven pixel circuit was constructed, which exhibited high controllability over the light-emitting diodes. Logic gates based on fully FTF-processed In 2 O 3 /AlO x TFTs were further realized, which exhibited good dynamic logic responses and voltage amplification by a factor of ∼4. The FTF technique presented here offers great potential in large-area and low-cost manufacturing for flexible oxide electronics.

Breast cancer is one of the leading cancer forms affecting females worldwide. Characterizing the mechanical properties of breast cancer tissue is important for diagnosis and uncovering the mechanobiology mechanism. Although most of the studies were based on human cancer tissue, an animal model is still describable for preclinical analysis. Using a custom-build indentation device, we measured the viscoelastic properties of breast cancer tissue from 4T1 and SKBR3 cell lines. A total of 7 samples were tested for each cancer tissue using a mouse model. We observed that a viscoelastic model with 2-term Prony series could best describe the ramp and stress relaxation of the tissue. For long-term responses, the SKBR3 tissues were stiffer in the strain levels of 4-10%, while no significant differences were found for the instantaneous elastic modulus. We also found tissues from both cell lines appeared to be strain-independent for the instantaneous elastic modulus and for the long-term elastic modulus in the strain level of 4-10%. In addition, by inspecting the cellular morphological structure of the two tissues, we found that SKBR3 tissues had a larger volume ratio of nuclei and a smaller volume ratio of extracellular matrix (ECM). Compared with prior cellular mechanics studies, our results indicated that ECM could contribute to the stiffening the tissue-level behavior. The viscoelastic characterization of the breast cancer tissue contributed to the scarce animal model data and provided support for the linear viscoelastic model used for in vivo elastography studies. Results also supplied helpful information for modeling of the breast cancer tissue in the tissue and cellular levels., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

Numerous studies have demonstrated that estrogens may exert multifaceted effects on the cardiovascular system via activating the classical nuclear receptors ERα or ERβ and the novel G protein coupled estrogen receptor (Gper). However, some studies have reported inconsistent cardiovascular phenotypes in Gper-deficient mice. The current study was aimed to reveal the effects of genetic deletion of Gper on the arterial blood pressure (ABP) and heart rate in rats. Gper-deficient Sprague-Dawley rats were generated by utilizing the CRISPR-Cas9 gene-editing technique. ABP of 10-week old male (n = 6) and 12-week old female (n = 6) Gper-deficient rats and age-matched wild type (WT) rats (6 females and 6 males) were measured under awake and restrained conditions through the non-invasive tail-cuff method daily for 8 (females) or 9 days (males). In the male WT rats, ABP and heart rate were slightly higher in day 1 to 4 than those in day 5 to 9, indicative of stress-related sympathoexcitation in the first few days and gradual adaptation to the restrained stress in later days. Gper-deficient rats had significantly higher ABP initially (male: day 1 to day 5; female: day 1 to day 3) and similar ABP in later days of measurement compared with the WT rats. The heart rate of male Gper-deficient rats was consistently higher than that of the male WT rats from day 1 to day 8. Both male and female Gper-deficient rats appeared to show slower body weight gain than the WT counterparts during the study period. Under anesthesia, ABP of Gper-deficient rats was not significantly different from their WT counterparts. These results indicate that Gper-deficient rats may be more sensitive to stress-induced sympathoexcitation and highlight the importance of Gper in the regulation of the cardiovascular function in stressful conditions.

Low-temperature solution processing opens a new window for the fabrication of oxide semiconductors due to its simple, low cost, and large-area uniformity. Herein, by using solution combustion synthesis (SCS), p-type Cu-doped NiO (Cu:NiO) thin films are fabricated at a temperature lower than 150 °C. The light doping of Cu substitutes the Ni site and disperses the valence band of the NiO matrix, leading to an enhanced p-type conductivity. Their integration into thin-film transistors (TFTs) demonstrates typical p-type semiconducting behavior. The optimized Cu 5% NiO TFT exhibits outstanding electrical performance with a hole mobility of 1.5 cm 2 V -1 s -1 , a large on/off current ratio of ≈10 4 , and clear switching characteristics under dynamic measurements. The employment of a high-k ZrO 2 gate dielectric enables a low operating voltage (≤2 V) of the TFTs, which is critical for portable and battery-driven devices. The construction of a light-emitting-diode driving circuit demonstrates the high current control capability of the resultant TFTs. The achievement of the low-temperature-processed Cu:NiO thin films via SCS not only provides a feasible approach for low-cost flexible p-type oxide electronics but also represents a significant step toward the development of complementary metal-oxide semiconductor circuits., (© 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Electrospun metal oxide nanofibers have been regarded as promising blocks for large-area, low-cost, and one-dimensional electronic devices. However, the electronic devices based on electrospun nanofibers usually suffer from poor performance and inferior viability. Here, we report an efficient photochemical process using UV light generated by a high-pressure mercury lamp to promote the electrical performance of the nanofiber-based electronic devices. Such UV treatment can lead to strong photochemical activation of electrospun nanofibers, and therefore, a stable adherent nanofiber network and electronic-clean interface were formed. By use of UV treatment, high-performance indium oxide (In 2 O 3 ) nanofiber based field-effect transistors (FETs) with highly efficient modulation of electrical characteristics have been successfully fabricated. To reduce the operating voltage and further improve the device performance, the In 2 O 3 nanofiber FETs based on solution-processed high-k AlO x dielectrics were integrated and investigated. The as-fabricated In 2 O 3 /AlO x FETs exhibit superior electrical performance, including a high mobility of 19.8 cm 2 V -1 s -1 , a large on/off current ratio of 10 6 , and high stability over time and cycling. The improved performance of the UV-treated FETs was further confirmed by the integration of the electrospun In 2 O 3 /AlO x FETs into inverters. This work presents an important advance toward the practical applications of electrospun nanofibers for functional electronic devices.

A uniform graphene nanodots inlaid porous gold electrode was prepared via ion beam sputtering deposition (IBSD) and mild corrosion chemistry. HRTEM, SEM, AFM and XPS analyses revealed the successful fabrication of graphene nanodots inlaid porous gold electrode. The as-prepared porous electrode was used as π-orbital-rich drug loading platform to fabricate an electrochemically controlled drug release system with high performance. π-orbital-rich drugs with amino mioety, like doxorubicin (DOX) and tetracycline (TC), were loaded into the graphene nanodots inlaid porous gold electrode via non-covalent π-π stacking interaction. The amino groups in DOX and TC can be easily protonated at acidic medium to become positively-charged NH3(+), which allow these drug molecules to be desorbed from the porous electrode surface via electrostatic repulsion when positive potential is applied at the electrode. The drug loading and release experiment indicated that this graphene nanodots inlaid porous gold electrode can be used to conveniently and efficiently control the drug release electrochemically. Not only did our work provide a benign method to electrochemically controlled drug release via electrostatic repulsion process, it also enlighten the promising practical applications of micro electrode as a drug carrier for precisely and efficiently controlled drug release via embedding in the body., (Copyright © 2015 Elsevier B.V. All rights reserved.)

Docosahexaenoic acid (DHA), a derivative of ω3- polyunsaturated fatty acids present in fish oil, is well known to have anticancer activity on colon cancer cells, but the molecular and cellular mechanisms remain to be further clarified. In this study, anti-cancer effects of DHA on colon cancer cells were observed in a nude mouse HCT-15 xenograft model. And then, the different genes expression and signal pathways involved in this process were screened and identified using cDNA microarray analysis. Results of genes expression profiles indicated a reprogramming pattern of previously known and unknown genes and transcription factors associated with the action of DHA on colon cancer cells. And several genes related to tumor growth and metastasis including COX2, HIF-1α, VEGF-A, COMP, MMP-1, MMP-9, SCP2, SDC3, which were down-regulated by DHA, were further confirmed in HCT-15 cell line using RT-PCR method. In summary, our data might provide novel information for anti-cancer mechanism of DHA in colon cancer model.

Objective: To investigate the radiographic features of submandibular sialiths in cone beam CT (CBCT) images., Methods: Eighty-four patients with submandibular radiopaque sialiths were included in this study. The clinical features of gender and age and the radiographic features on CBCT, including the number, morphology, size, and location, were recorded for further statistical analysis., Results: A total of 128 sialiths were detected from the 84 subjects; 22 subjects (26.19%) had multiple sialiths. The morphology of the sialiths was classified into five types: spot, round, spheroid, elongated, and irregular shapes. Among these types, the spheroid shape was the most frequently detected. A correlation was observed between the size of the sialiths and their location, with the large sialith located at the posterior portion of the duct. About 39.06% (50/128) of sialiths was located at the anterior portion of the duct, and 60.94% (78/128) was located at the posterior portion. The horizon- tal position of the sialith was significantly correlated with its vertical position (P < 0.0001)., Conclusion: The CBCT images showed important data for the evaluation, diagnosis, and treatment plan of the submandibular sialolithiasis.

Background: The aim of this study was to evaluate the effects of topical ropivacaine anesthesia on hemodynamic responses during intubation and extubation of hypertensive patients., Material and Methods: One hundred fifty patients with hypertension ASA II-III were scheduled for noncardiac operations. Patients were divided into 3 groups: a control group receiving 5 ml saline, and 2 groups receiving topical anesthesia with 100 mg lidocaine or 37.5 mg ropivacaine. Hemodynamic responses, including blood pressure and heart rate (HR), were recorded at baseline (T0), before intubation (T1), during tracheal intubation (T2), 2 min after intubation (T3), upon eye opening on verbal commands (T4), during tracheal extubation (T5), and 2 min after extubation (T6). Patients were injected with urapidil 5 mg during intubation and extubation if their systolic blood pressure (SBP) was ≥160 mmHg or diastolic blood pressure (DBP) was ³90 mmHg, and esmolol 10 mg when HR was ≥90 bpm., Results: During extubation, the total dosages of urapidil and esmolol were significantly higher in the saline than in the lidocaine or ropivacaine groups, and were significantly lower in the ropivacaine than in the lidocaine group. At T2, SBP, SBP, MAP, and HR were lower in the lidocaine and ropivacaine groups than in the saline group, but the differences were not significant. From T4 to T6, SBP, DBP, MAP, and HR were significantly lower in the ropivacaine group than in the other 2 groups (P<0.05 each)., Conclusions: Topical lidocaine and ropivacaine anesthesia can effectively reduce hemodynamic responses during intubation, with ropivacaine better at inhibiting hemodynamic changes at emergence in hypertensive patients.

Epstein-Barr virus (EBV) alters the regulation and expression of a variety of cytokines in its host cells to modulate host immune surveillance and facilitate viral persistence. Using cytokine antibody arrays, we found that, in addition to the cytokines reported previously, two chemotactic cytokines, CCL3 and CCL4, were induced in EBV-infected B cells and were expressed at high levels in all EBV-immortalized lymphoblastoid cell lines (LCLs). Furthermore, EBV latent membrane protein 1 (LMP1)-mediated Jun N-terminal protein kinase activation was responsible for upregulation of CCL3 and CCL4. Inhibition of CCL3 and CCL4 in LCLs using a short hairpin RNA approach or by neutralizing antibodies suppressed cell proliferation and caused apoptosis, indicating that autocrine CCL3 and CCL4 are required for LCL survival and growth. Importantly, significant amounts of CCL3 were detected in EBV-positive plasma from immunocompromised patients, suggesting that EBV modulates this chemokine in vivo. This study reveals the regulatory mechanism and a novel function of CCL3 and CCL4 in EBV-infected B cells. CCL3 might be useful as a therapeutic target in EBV-associated lymphoproliferative diseases and malignancies.

Human cytomegalovirus (HCMV) is a large DNA virus and a member of the betaherpesvirus family. HCMV infection is extremely common in human populations and can cause severe diseases in immunocompromised hosts. Ganciclovir is the most widely used antiviral drug for cytomegalovirus infection and works by blocking the amplification of HCMV. HCMV strains resistant to ganciclovir have been detected in recent decades and mainly result from mutations in UL97 (protein kinase) and UL54 (DNA polymerase) genes. In order to understand the prevalence of resistance of HCMV in Taiwan, we studied 40 clinical isolates to detect the mutations of UL97 and UL54 that might be related to resistance. The results showed that no mutation known to cause ganciclovir resistance was detected in any strain, but some polymorphisms (N685S, A688V, A885T, N898D in UL54; D605E in UL97) were frequently observed. Our results suggest that resistant HCMV strains are not prevalent in Taiwan., (Copyright © 2012. Published by Elsevier B.V.)