Search

We discuss the analyses of gated, x-ray imaging data from polar-direct-drive experiments with cryogenically layered deuterium–tritium targets on the OMEGA laser. The in-flight shell asymmetries were diagnosed at various times during the implosion, which was caused by the beam pointing geometry and preimposed variations in the energy partition between the different groups of laser beams. The shape of the ablation surface during the acceleration phase of the implosion was measured along two different lines of sight, and a Legendre mode ( ℓ-mode) decomposition was applied for modes of up to ten to investigate shell asymmetries. A clear causal relationship between the imposed beam imbalance and the shape of the in-flight shell asymmetries was observed. The imploded shell with a balanced energy ratio shows smaller values of the amplitudes of ℓ-mode 2 compared to that from implosions with an imbalanced ring energy ratio. The amplitudes of ℓ-modes 4 and 6 are the same within the measurement uncertainty with respect to the change in beam energy ratio.

A three-dimensional model of the hot-spot x-ray emission has been developed and applied to the study of low-mode drive asymmetries in direct-drive inertial confinement fusion implosions on OMEGA with cryogenic deuterium–tritium targets. The steady-state model assumes an optically thin plasma and the data from four x-ray diagnostics along quasi-orthogonal lines of sight are used to obtain a tomographic reconstruction of the hot spot. A quantitative analysis of the hot-spot shape is achieved by projecting the x-ray emission into the diagnostic planes and comparing this projection to the measurements. The model was validated with radiation-hydrodynamic simulations assuming a mode-2 laser illumination perturbation resulting in an elliptically shaped hot spot, which was accurately reconstructed by the model using synthetic x-ray images. This technique was applied to experimental data from implosions in polar-direct-drive illumination geometry with a deliberate laser-drive asymmetry, and the hot-spot emission was reconstructed using spherical-harmonic modes of up to ℓ = 3. A 10% stronger drive on the equator relative to that on the poles resulted in a prolate-shaped hot spot at stagnation with a large negative A2,0 coefficient of A2,0 = −0.47 ± 0.03, directly connecting the modal contribution of the hot-spot shape with the modal contribution in laser-drive asymmetry.

Spherical implosions in inertial confinement fusion are inherently sensitive to perturbations that may arise from experimental constraints and errors. Control and mitigation of low-mode (long wavelength) perturbations is a key milestone to improving implosion performances. We present the first 3D radiation-hydrodynamic simulations of directly driven inertial confinement fusion implosions with an inline package for polarized crossed-beam energy transfer. Simulations match bang times, yields (separately accounting for laser-induced high modes and fuel age), hot spot flow velocities and direction, for which polarized crossed-beam energy transfer contributes to the systematic flow orientation evident in the OMEGA implosion database. Current levels of beam mispointing, imbalance, target offset, and asymmetry from polarized crossed-beam energy transfer degrade yields by more than 40%. The effectiveness of two mitigation strategies for low modes is explored.

PECHMANN'S CONDENSATION OF METHYL β-RESORCYLATE AND , β-RESORCYLIC ACID WITH ETHYL ACETOACETATE.&nbsp

The injection and mixing of contaminant mass into the fuel in inertial confinement fusion (ICF) implosions is a primary factor preventing ignition. ICF experiments have recently achieved an alpha-heating regime, in which fusion self-heating is the dominant source of yield, by reducing the susceptibility of implosions to instabilities that inject this mass. We report the results of unique separated reactants implosion experiments studying pre-mixed contaminant as well as detailed high-resolution three-dimensional simulations that are in good agreement with experiments. At conditions relevant to mixing regions in high-yield implosions, we observe persistent chunks of contaminant that do not achieve thermal equilibrium with the fuel throughout the burn phase. The assumption of thermal equilibrium is made in nearly all computational ICF modeling and methods used to infer levels of contaminant from experiments. We estimate that these methods may underestimate the amount of contaminant by a factor of two or more., The influence of contaminants is one of the factors hindering self-sustained thermonuclear burn in inertial confinement fusion. Here, the authors present evidence, through simulations and experiments, that contaminants do not fully reach thermal equilibrium, and thus their amount is usually underestimated.

Low- and mid-mode perturbations are possible candidates for performance limitations in cryogenic direct-drive implosions on the OMEGA laser at the Laboratory of Laser Energetics. Simulations with a 3D hydrocode demonstrated that hotspot imagers do not show evidence of the shell breakup in the dense fuel. However, these same simulations revealed that the low- and mid-mode perturbations in the dense fuel could be diagnosed more easily in the post-stagnation phase of the implosion by analyzing the peak in the x-ray emission limb at the coronal–fuel interface than before or at the stagnation phase. In experiments, the asymmetries are inferred from gated images of the x-ray emission of the implosion by using a 16-pinhole array imager filtered to record x-ray energies >800 eV and an x-ray framing camera with 40-ps time integration and 20- μm spatial resolution. A modal analysis is applied to the spatial distribution of the x-ray emission from deuterium and tritium cryogenic implosions on OMEGA recorded after the bang time to diagnose the low- and mid-mode asymmetries, and to study the effect that the beam-to-target ratio ( Rb/ Rt) has on the shell integrity.

In laser-driven implosions for laboratory fusion, the comparison of hot-spot x-ray yield to neutron production can serve to infer hot-spot mix. For high-performance direct-drive implosions, this ratio depends sensitively on the degree of equilibration between the ion and electron fluids. A scaling for x-ray yield as a function of neutron yield and characteristic ion and electron hot-spot temperatures is developed on the basis of simulations with varying degrees of equilibration. We apply this model to hot-spot x-ray measurements of direct-drive cryogenic implosions typical of the direct-drive designs with best ignition metrics. The comparison of the measured x-ray and neutron yields indicates that hot-spot mix, if present, is below a sensitivity estimated as ∼2% by-atom mix of ablator plastic into the hot spot.

A system of x-ray imaging spectrometer (XRIS) has been implemented at the OMEGA Laser Facility and is capable of spatially and spectrally resolving x-ray self-emission from 5 to 40 keV. The system consists of three independent imagers with nearly orthogonal lines of sight for 3D reconstructions of the x-ray emission region. The distinct advantage of the XRIS system is its large dynamic range, which is enabled by the use of tantalum apertures with radii ranging from 50 μm to 1 mm, magnifications of 4 to 35×, and image plates with any filtration level. In addition, XRIS is capable of recording 1–100’s images along a single line of sight, facilitating advanced statistical inference on the detailed structure of the x-ray emitting regions. Properties such as P0 and P2 of an implosion are measured to 1% and 10% precision, respectively. Furthermore, T e can be determined with 5% accuracy.

Statistical modeling of experimental and simulation databases has enabled the development of an accurate predictive capability for deuterium-tritium layered cryogenic implosions at the OMEGA laser [V. Gopalaswamy et al.,Nature 565, 581 (2019)10.1038/s41586-019-0877-0]. In this letter, a physics-based statistical mapping framework is described and used to uncover the dependencies of the fusion yield. This model is used to identify and quantify the degradation mechanisms of the fusion yield in direct-drive implosions on OMEGA. The yield is found to be reduced by the ratio of laser beam to target radius, the asymmetry in inferred ion temperatures from the ℓ=1 mode, the time span over which tritium fuel has decayed, and parameters related to the implosion hydrodynamic stability. When adjusted for tritium decay and ℓ=1 mode, the highest yield in OMEGA cryogenic implosions is predicted to exceed 2×10^{14} fusion reactions.

Hot-spot shape and electron temperature (Te) are key performance metrics used to assess the efficiency of converting shell kinetic energy into hot-spot thermal energy in inertial confinement fusion implosions. X-ray penumbral imaging offers a means to diagnose hot-spot shape and Te, where the latter can be used as a surrogate measure of the ion temperature (Ti) in sufficiently equilibrated hot spots. We have implemented a new x-ray penumbral imager on OMEGA. We demonstrate minimal line-of-sight variations in the inferred Te for a set of implosions. Furthermore, we demonstrate spatially resolved Te measurements with an average uncertainty of 10% with 6 μm spatial resolution.

Focusing laser light onto a very small target can produce the conditions for laboratory-scale nuclear fusion of hydrogen isotopes. The lack of accurate predictive models, which are essential for the design of high-performance laser-fusion experiments, is a major obstacle to achieving thermonuclear ignition. Here we report a statistical approach that was used to design and quantitatively predict the results of implosions of solid deuterium-tritium targets carried out with the 30-kilojoule OMEGA laser system, leading to tripling of the fusion yield to its highest value so far for direct-drive laser fusion. When scaled to the laser energies of the National Ignition Facility (1.9 megajoules), these targets are predicted to produce a fusion energy output of about 500 kilojoules-several times larger than the fusion yields currently achieved at that facility. This approach could guide the exploration of the vast parameter space of thermonuclear ignition conditions and enhance our understanding of laser-fusion physics.

Three-dimensional effects play a crucial role during the hot-spot formation in inertial confinement fusion (ICF) implosions. A data analysis technique for 3D hot-spot reconstruction from experimental observables has been developed to characterize the effects of low modes on 3D hot-spot formations. In nuclear measurements, the effective flow direction, governed by the maximum eigenvalue in the velocity variance of apparent ion temperatures, has been found to agree with the measured hot-spot flows for implosions dominated by mode [Formula: see text]. Asymmetries in areal-density ( ρR) measurements were found to be characterized by a unique cosine variation along the hot-spot flow axis. In x-ray images, a 3D hot-spot x-ray emission tomography method was developed to reconstruct the 3D hot-spot plasma emissivity using a generalized spherical-harmonic Gaussian function. The gradient-descent algorithm was used to optimize the mapping between the projections from the 3D hot-spot emission model and the measured x-ray images along multiple views. This work establishes a platform to analyze 3D low-mode core asymmetries in ICF.

In deuterium-tritium cryogenic implosions, hot-spot x-ray self-emission is observed to begin at a larger shell radius than is predicted by a one-dimensional radiation-hydrodynamic implosion model. Laser-imprint is shown to explain the observation for a low-adiabat implosion. For more-stable implosions the data are not described by the imprint model and suggest there are additional sources of decompression of the dense fuel.

In inertial confinement fusion (ICF), deuterium-tritium (DT) fuel is brought to densities and temperatures where fusion ignition occurs. Mix of ablator material into the fuel may prevent ignition by diluting and cooling the fuel. MARBLE experiments at the National Ignition Facility (NIF) provide new insight into how mix affects thermonuclear burn. These experiments use laser-driven capsules containing deuterated plastic foam and tritium gas. Embedded within the foam are voids of known sizes and locations, which control the degree of heterogeneity of the fuel. Initially, the reactants are separated, with tritium concentrated in the voids and deuterium in the foam. During the implosion, mix occurs, leading to DT fusion reactions in the mixed region. Here we show that by measuring ratios of DT and deuterium-deuterium (DD) neutron yields for different macropore sizes and gas compositions, effects of mix heterogeneity on thermonuclear burn may be quantified and understood for the first time.

Using highly resolved 3D radiation-hydrodynamic simulations, we identify a novel mechanism by which the deleterious impact of laser imprinting is mitigated in direct-drive inertial confinement fusion. Unsupported shocks and associated rarefaction flows, commonly produced with short laser bursts, are found to reduce imprint modulations prior to target acceleration. Optimization through the choice of laser pulse with picket(s) and target dimensions may improve the stability of lower-adiabat designs, thus providing the necessary margin for ignition-relevant implosions.

Nonuniformities present in the laser illumination and target in laser-driven inertial confinement fusion experiments lead to an asymmetric compression of the target, resulting in an inefficient conversion of shell kinetic energy to thermal energy of the hot-spot plasma. In this paper, the effects of asymmetric compression of cryogenic deuterium tritium laser-direct-drive implosions are examined using a suite of nuclear and x-ray diagnostics on the OMEGA laser. The neutron-averaged hot-spot velocity ( u → hs) and apparent ion temperature ( T i) asymmetry are determined from neutron time-of-flight measurements of the primary deuterium tritium fusion neutron energy spectrum, while the areal density (ρR) of the compressed fuel surrounding the hot spot is inferred from measurements of the scattered neutron energy spectrum. The low-mode perturbations of the hot-spot shape are characterized from x-ray self-emission images recorded along three quasi-orthogonal lines of sight. Implosions with significant mode-1 laser-drive asymmetries show large hot-spot velocities (>100 km/s) in a direction consistent with the hot-spot elongation observed in x-ray images, measured T i asymmetry, and ρR asymmetry. Laser-drive corrections have been applied through shifting the initial target location in order to mitigate the observed asymmetry. With the asymmetry corrected, a more-symmetric hot spot is observed with reduced u → hs , T i asymmetry, ρR asymmetry, and a 30% increase in the fusion yield.

The Marble campaign on the National Ignition Facility investigates the effect of heterogeneous mix on thermonuclear burn for comparison to a probability distribution function (PDF) burn model. Marble utilizes plastic capsules filled with deuterated plastic foam and a fill gas containing tritium. As the capsules implode, the deuterium in the foam mixes with the tritium gas, and DT neutrons are produced as the shocks compress and heat the mixture. The yield of DT neutrons is dependent on the uniformity of the mix, with more heterogeneous mix producing fewer neutrons. In Marble, the heterogeneity of the mix is controlled by varying the diameter of voids introduced into the foam. The first NIF Marble campaign has been executed in which the Marble capsules were indirectly driven with a single strong shock using NIF hohlraums. The experiments produce a low-convergence, high-ion-temperature implosion. The ratio of DT to DD neutron yield is largely consistent with uniform atomic mix for fine-pore foam, and increases slightly with void diameter, contrary to 1D simulations using the PDF burn model. Recent 3D high-resolution simulations of similar experiments performed on the Omega Laser Facility suggest an explanation.

Laser-direct drive (LDD), along with laser indirect (X-ray) drive (LID) and magnetic drive with pulsed power, is one of the three viable inertial confinement fusion approaches to achieving fusion ignition and gain in the laboratory. The LDD programme is primarily being executed at both the Omega Laser Facility at the Laboratory for Laser Energetics and at the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory. LDD research at Omega includes cryogenic implosions, fundamental physics including material properties, hydrodynamics and laser–plasma interaction physics. LDD research on the NIF is focused on energy coupling and laser–plasma interactions physics at ignition-scale plasmas. Limited implosions on the NIF in the ‘polar-drive’ configuration, where the irradiation geometry is configured for LID, are also a feature of LDD research. The ability to conduct research over a large range of energy, power and scale size using both Omega and the NIF is a major positive aspect of LDD research that reduces the risk in scaling from OMEGA to megajoule-class lasers. The paper will summarize the present status of LDD research and plans for the future with the goal of ultimately achieving a burning plasma in the laboratory.This article is part of a discussion meeting issue ‘Prospects for high gain inertial fusion energy (part 2)’.

Radiographs of pure-DT cryogenic imploding shells provide critical validation of progress toward ignition-scalable performance of inertial confinement fusion implosions [J. Nuckolls et al., Nature 239, 139 (1972)]. Cryogenic implosions on the OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] can be self-radiographed by their own core spectral emission near ≈2 keV. Utilizing the distinct spectral dependences of continuum emissivity and opacity, the projected optical-thickness distribution of imploded shells, i.e., the shell radiograph, can be distinguished from the structure of the core emission distribution in images. Importantly, this can be done without relying on spectral additives (shell dopants), as in previous applications of implosion self-radiography [V. A. Smalyuk et al., Phys. Rev. Lett. 87, 155002 (2001); L. A. Pickworth et al., ibid. 117, 035001 (2016)]. Demonstrations with simulated data show that this technique is remarkably well-suited to cryogenic implosions and can also be applied to self-radiography of imploded room-temperature CH shells at higher spectral energy (hv ≈ 3–5 keV) based on the very similar continuum spectrum of carbon. Experimental demonstration of additive-free self-radiography with warm CH shell implosions on OMEGA will provide an important proof of principle for future applications to cryogenic DT implosions.

International audience; The unintentional mispositioning of inertial confinement fusion (ICF) capsules from the center of laser beam convergence has long been shown in simulations to generate large ℓ=1 asymmetry and significantly degrade implosion symmetry and fusion yields. Experimental yields on the OMEGA laser system, however, have shown much less sensitivity to this initial target offset. This paper presents simulations of offset ICF implosions improved by including a physics model of cross-beam energy transfer (CBET), a mechanism of laser energy scattering from one beam to another. Room-temperature OMEGA implosion experiments with prescribed target offsets are simulated with and without CBET, illustrating that CBET mitigates the ℓ=1 implosion asymmetry from the target offset. Comparison of simulations to multiple complementary experimental observables indicates that the addition of CBET physics in offset simulations is necessary to match experimental results.

The MARBLE project is a novel inertial confinement fusion platform for studying the development of atomic mixing and temperature equilibration in inertial confinement fusion implosions and their impact on thermonuclear burn. Experiments involve the laser-driven implosion of capsules filled with deuterated engineered foams whose pores are filled with a gaseous mixture of hydrogen and tritium. By varying the size of the foam pores, we can study the timescale of the development of atomic mix relative to the development of thermal equilibrium between species. In contrast, previous separated reactant experiments have only provided information on the total amount of mix mass. We report on the series of MARBLE experiments [first reported in Haines et al., Nat. Commun. 11, 544 (2020)] performed on the University of Rochester's OMEGA laser facility and detailed and highly resolved three-dimensional radiation-hydrodynamic simulations of the implosions. In both the experimental and simulation results, we observe that the reactants do not achieve thermal equilibrium during the course of the implosion except in atomically mixed regions—i.e., that atomic mixing develops faster than thermal equilibration between species. The results suggest that ion temperature variations in the mixture are at least as important as reactant concentration variations for determining the fusion reaction rates.

A method was developed with laser-irradiated Au planar foils to characterize the focal spot of UV laser beams on a target at full energy from soft x-ray emission. A pinhole camera with a back-thinned charge-coupled device detector and filtration with thin Be and Al foil filters provides images of the x-ray emission at photon energies

The single-line-of-sight, time-resolved x-ray imager (SLOS-TRXI) on OMEGA is one of a new generation of fast-gated x-ray cameras comprising an electron pulse-dilation imager and a nanosecond-gated, burst-mode, hybrid complementary metal-oxide semiconductor sensor. SLOS-TRXI images the core of imploded cryogenic deuterium–tritium shells in inertial confinement fusion experiments in the ∼4- to 9-keV photon energy range with a pinhole imager onto a photocathode. The diagnostic is mounted on a fixed port almost perpendicular to a 16-channel, framing-camera–based, time-resolved Kirkpatrick–Baez microscope, providing a second time-gated line of sight for hot-spot imaging on OMEGA. SLOS-TRXI achieves ∼40-ps temporal resolution and better than 10-μm spatial resolution. Shots with neutron yields of up to 1 × 1014 were taken without observed neutron-induced background signal. The implosion images from SLOS-TRXI show the evolution of the stagnating core.

Experimental data are presented showing maximum carbon C6+ ion energies obtained from nm-scaled targets in the relativistic transparent regime for laser intensities between 9 × 1019 and 2 × 1021 W/cm2. When combined with two-dimensional particle-in-cell simulations, these results show a steep linear scaling for carbon ions with the normalized laser amplitude a0 ($a_0 \propto \sqrt ( I)$). The results are in good agreement with a semi-analytic model that allows one to calculate the optimum thickness and the maximum ion energies as functions of a0 and the laser pulse duration τλ for ion acceleration in the relativistic-induced transparency regime. Following our results, ion energies exceeding 100 MeV/amu may be accessible with currently available laser systems.

Introduction: Ultrasonography has established itself as an invaluable tool in surgery. In surgical practice, abdominal pain is perhaps the most common symptom encountered and almost in every case of abdominal pain surgeon prefers to use the ultrasound to confirm the diagnosis. Although physical examination of the patient is the most important part in proper diagnosis many a time some positive help is required in the form of investigations especially ultrasonography. Methods: This was a study of hundred patients carried out at a tertiary care hospital admitted with complaints of severe abdominal pain except those with a history of trauma or with a history of chronic abdominal pain. Clinical history, physical examination, ultrasonography, per operative findings and histo-pathological examination were used to come to a final conclusion. Result: In this study ultrasonography was diagnostic in 78% of patients. Two patients were misdiagnosed and in 20 patients other investigations were required for the confirmation of diagnosis. The sensitivity and specificity of ultrasound in diagnosing acute appendicitis, renal calculus, liver abscess, mesenteric lymphadenitis, acute pancreatitis and ovarian cyst was 100% and in calculus cholecystitis it was 93.75% and 100% respectively. Conclusion: Ultrasonography is superior in organ system imaging. It helps in showing organ specific lesions and its accurate measurement which is helpful in follow up and response to treatment. Ultrasonography is also helpful in diagnosing alternative disease and to reduce negative laparotomy rate.

We present narrow-band self-emission x-ray images from a titanium tracer layer placed at the fuel-shell interface in 60-laser-beam implosion experiments at the OMEGA facility. The images are acquired during deceleration with inferred convergences of ∼9-14. Novel here is that a systematically observed asymmetry of the emission is linked, using full sphere 3D implosion modeling, to performance-limiting low mode asymmetry of the drive.

Coherent synchrotron emission from relativistic laser-plasma interactions is an exciting route towards bright attosecond pulse production. We demonstrate experimentally the critical role that laser contrast on 1-2 picosecond timescales plays in the detailed generation mechanism.

Cost-effective strategies to maintain healthy active lifestyle in aging populations are required to address the global burden of age-related diseases. ASPREE will examine whether the potential primary prevention benefits of low dose aspirin outweigh the risks in older healthy individuals. Our primary hypothesis is that daily oral 100. mg enteric-coated aspirin will extend a composite primary endpoint termed 'disability-free life' including onset of dementia, total mortality, or persistent disability in at least one of the Katz Activities of Daily Living in 19,000 healthy participants aged 65. years and above ('US minorities') and 70. years and above (non-'US minorities'). ASPREE is a double-blind, randomized, placebo-controlled trial of oral 100. mg enteric-coated acetyl salicylic acid (ASA) or matching placebo being conducted in Australian and US community settings on individuals free of dementia, disability and cardiovascular disease (CVD) events. Secondary endpoints are all-cause and cause specific mortality, fatal and non-fatal cardiovascular events, fatal and non-fatal cancer (excluding non-melanoma skin cancer), dementia, mild cognitive impairment, depression, physical disability, and clinically significant bleeding. To 20 September 2013 14,383 participants have been recruited. Recruitment and study completion are anticipated in July 2014 and December 2018 respectively. In contrast to other aspirin trials that have largely focused on cardiovascular endpoints, ASPREE has a unique composite primary endpoint to better capture the overall risk and benefit of aspirin to extend healthy independent lifespan in older adults in the US and Australia.

The first cryogenic deuterium and deuterium-tritium liquid layer implosions at the National Ignition Facility (NIF) demonstrate D_{2} and DT layer inertial confinement fusion (ICF) implosions that can access a low-to-moderate hot-spot convergence ratio (12CR25). Previous ICF experiments at the NIF utilized high convergence (CR30) DT ice layer implosions. Although high CR is desirable in an idealized 1D sense, it amplifies the deleterious effects of asymmetries. To date, these asymmetries prevented the achievement of ignition at the NIF and are the major cause of simulation-experiment disagreement. In the initial liquid layer experiments, high neutron yields were achieved with CRs of 12-17, and the hot-spot formation is well understood, demonstrated by a good agreement between the experimental data and the radiation hydrodynamic simulations. These initial experiments open a new NIF experimental capability that provides an opportunity to explore the relationship between hot-spot convergence ratio and the robustness of hot-spot formation during ICF implosions.

Experiments on the National Ignition Facility show that multi-dimensional effects currently dominate the implosion performance. Low mode implosion symmetry and hydrodynamic instabilities seeded by capsule mounting features appear to be two key limiting factors for implosion performance. One reason these factors have a large impact on the performance of inertial confinement fusion implosions is the high convergence required to achieve high fusion gains. To tackle these problems, a predictable implosion platform is needed meaning experiments must trade-off high gain for performance. LANL has adopted three main approaches to develop a one-dimensional (1D) implosion platform where 1D means measured yield over the 1D clean calculation. A high adiabat, low convergence platform is being developed using beryllium capsules enabling larger case-to-capsule ratios to improve symmetry. The second approach is liquid fuel layers using wetted foam targets. With liquid fuel layers, the implosion convergence can be controlled via the initial vapor pressure set by the target fielding temperature. The last method is double shell targets. For double shells, the smaller inner shell houses the DT fuel and the convergence of this cavity is relatively small compared to hot spot ignition. However, double shell targets have a different set of trade-off versus advantages. Details for each of these approaches are described.

Extreme ultraviolet and X-ray radiation can be generated when the high harmonics of incident laser light are reflected by a dense plasma, the so-called relativistically oscillating mirror mechanism. Theoretical studies have, however, predicted an alternative regime in which short-wavelength light is generated by dense electron nanobunches that form at the plasma–vacuum boundary. Signatures of this coherent synchrotron emission are now experimentally observed.

When electrons are accelerated to near light-speeds through an overdense plasma by an intense laser beam, the usually opaque plasma becomes optically transparent. High-speed laser experiments provide unprecedented insight into the dynamics of this process.

Table-top laser–plasma ion accelerators have many exciting applications, many of which require ion beams with simultaneous narrow energy spread and high conversion efficiency. However, achieving these requirements has been elusive. Here we report the experimental demonstration of laser-driven ion beams with narrow energy spread and energies up to 18 MeV per nucleon and ∼5% conversion efficiency (that is 4 J out of 80-J laser). Using computer simulations we identify a self-organizing scheme that reduces the ion energy spread after the laser exits the plasma through persisting self-generated plasma electric (∼1012 V m−1) and magnetic (∼104 T) fields. These results contribute to the development of next generation compact accelerators suitable for many applications such as isochoric heating for ion-fast ignition and producing warm dense matter for basic science., Table-top laser-plasma ion accelerators have many potential applications, but achieving simultaneous narrow energy spread and high efficiency remains a challenge. Here, the authors produce ion beams with up to 18 MeV per nucleon whilst keeping the energy spread reduced through a self-organized process.

Beryllium is a candidate ablator material for indirect-drive inertial confinement fusion experiments, motivated by its high mass ablation rate, which is advantageous for implosion coupling efficiency and stabilization of the ablation-front instability growth. We present new data on the shock propagation, in-flight shape, and hot spot self-emission shape from gas-filled capsules that demonstrate the feasibility of predictable, symmetric, controllable beryllium implosions at a case-to-capsule ratio of 3.7. The implosions are round (Legendre mode 2 amplitude ≲5%) at an inner beam power and the energy fraction of 26%–28% of the total, indicating that larger beryllium capsules could be driven symmetrically using the National Ignition Facility.

This paper describes a technique for identifying trends in performance degradation for inertial confinement fusion implosion experiments. It is based on reconstruction of the implosion core with a combination of low- and mid-mode asymmetries. This technique was applied to an ensemble of hydro-equivalent deuterium–tritium implosions on OMEGA which achieved inferred hot-spot pressures ≈56 ± 7 Gbar [Regan et al., Phys. Rev. Lett. 117, 025001 (2016)]. All the experimental observables pertaining to the core could be reconstructed simultaneously with the same combination of low and mid-modes. This suggests that in addition to low modes, which can cause a degradation of the stagnation pressure, mid-modes are present which reduce the size of the neutron and x-ray producing volume. The systematic analysis shows that asymmetries can cause an overestimation of the total areal density in these implosions. It is also found that an improvement in implosion symmetry resulting from correction of either the systematic mid or low modes would result in an increase in the hot-spot pressure from 56 Gbar to ≈ 80 Gbar and could produce a burning plasma when the implosion core is extrapolated to an equivalent 1.9 MJ symmetric direct illumination [Bose et al., Phys. Rev. E 94, 011201(R) (2016)].

Liquid layer implosions using the “wetted foam” technique, where the liquid fuel is wicked into a supporting foam, have been recently conducted on the National Ignition Facility for the first time [Olson et al., Phys. Rev. Lett. 117, 245001 (2016)]. We report on a series of wetted foam implosions where the convergence ratio was varied between 12 and 20. Reduced nuclear performance is observed as convergence ratio increases. 2-D radiation-hydrodynamics simulations accurately capture the performance at convergence ratios (CR) ∼ 12, but we observe a significant discrepancy at CR ∼ 20. This may be due to suppressed hot-spot formation or an anomalous energy loss mechanism.

Electrons have been accelerated from ultra-thin diamond-like carbon (DLC) foils by an ultrahigh-intensity laser pulse. A distinct quasi-monoenergetic electron spectrum peaked at 30 MeV is observed at a target thickness as thin as 5 nm which is in contrast to the observations of wide spectral distributions for thicker targets. At the same time, a substantial drop in laser-accelerated ion energies is found. The experimental findings give first indication that relativistic electron sheets can be generated from ultra-thin foils which in future may be used to generate brilliant X-ray beams by the coherent reflection of a second laser.

To address few-shot pulse contrast measurement, we present a correlator coupling the high gain of an optical parametric amplification scheme with large pulse tilt. This combination enables a low sensitivity charge coupled device (CCD) to observe features in the pulse intensity within a 50 ps single-shot window with inter-window dynamic range >107 and

Study of Variations in the Electron Desity Profiles and the Electrojet Irregularities caused by the Solar Eclipse

Triggering of Ionospheric Irregularities by the Solar Eclipse

The Constitution of Oroxylin - A Part II: Attempted Synthesis of Oroxylin - A and the Synthesis of Wogonin

New Synthetical Methods in Coumarin Chemistry

The wetted foam capsule design for inertial confinement fusion capsules, which includes a foam layer wetted with deuterium-tritium liquid, enables layered capsule implosions with a wide range of hot-spot convergence ratios (CR) on the National Ignition Facility. We present a full-scale wetted foam capsule design that demonstrates high gain in one-dimensional simulations. In these simulations, increasing the convergence ratio leads to an improved capsule yield due to higher hot-spot temperatures and increased fuel areal density. High-resolution two-dimensional simulations of this design are presented with detailed and well resolved models for the capsule fill tube, support tent, surface roughness, and predicted asymmetries in the x-ray drive. Our modeling of these asymmetries is validated by comparisons with available experimental data. In 2D simulations of the full-scale wetted foam capsule design, jetting caused by the fill tube is prevented by the expansion of the tungsten-doped shell layer due to prehe...