Search

Reducing the time for drying sawn timber to a certain moisture level without deteriorating its quality is increasingly important for an economic and energy-efficient industrial timber-drying process and to support the transition to a sustainable society. It is, however, crucial to ensure that the quality of the timber, i.e. the degree of distortion, cracking, discolouration, and moisture variation within and between the pieces in a drying batch, is not compromised. Drying-simulation software tend to be too conservative in drying-rate recommendations, which has been observed in practise particularly for large cross-section timber of Norway spruce. This study investigated the drying rate and checking occurrence of centre-yielded Norway spruce planks when dried with more aggressive schedules than normally used in practise, i.e. using higher dry-bulb temperatures and/or lower relative humidities than recommended in the conventional optimisation programmes used in the sawmill industry in Sweden. The objective was to investigate the possibility to considerably reduce the total drying time without compromising the quality of the dried timber. The quality of the planks was indirectly assessed by estimating their moisture-content distributions, calculating the moisture gradients and monitoring checking. This was achieved with 4D (3D + time) X-ray computed tomography and a recently developed image processing algorithm based on elastic image registration. The key findings in this study suggest that Norway spruce timber can be dried with significantly higher temperatures and lower relative humidities than suggested by simulations, leading to reduced total drying time without inducing checking. This methodology can help to improve the design of drying schedules to reduce drying time and energy consumption while maintaining timber quality at a level accepted by the customers. [ABSTRACT FROM AUTHOR]

Construction of buildings with wooden frames higher than two stories has been permitted in Sweden since 1994. As construction of multi-story buildings with wooden frames is relatively new, people in the construction industry are more likely to construct these buildings with concrete frames. The current research evaluates the factors influencing the choice of wooden frames for construction of multi-story buildings in Sweden. The purpose of this study is to explain which advantages and disadvantages construction companies in Sweden consider with wooden construction and to highlight the factors for why multi-story buildings are built with wood to a lesser extent than with other materials. The main goal is to investigate what factors or assumptions construction companies base their decisions on, and whether experience and competence in wooden frames for construction of multi-story buildings are considered in short supply in Sweden today. The chosen method for this research is a descriptive survey study with a qualitative and quantitative approach. The survey is based on respondents from five leading building companies in Sweden with regard to the companies' revenue. The respondents had either previous experience in constructing multi-story buildings with wooden frames, experienced respondents (ERs), or no experience, unexperienced respondents (UERs). 63% of the respondents were ERs, while 37% of them were UERs. It is resulted that the respondents think there is a lack of competence and experience in wooden frames for construction of multi-story buildings in Sweden. Factors that have the greatest impact on decisions to construct with wooden frames are positive environmental and climatic aspects as well as production advantages. Factors that are considered as major obstacles to construct with wooden frames are cost, acoustics, and moisture problems. [ABSTRACT FROM AUTHOR]

Climate change in high latitude regions leads to both higher temperatures and more precipitation but their combined effects on terrestrial ecosystem processes are poorly understood. In nitrogen (N) limited and often moss-dominated tundra and boreal ecosystems, moss-associated N 2 fixation is an important process that provides new N. We tested whether high mean annual precipitation enhanced experimental warming effects on growing season N 2 fixation in three common arctic-boreal moss species adapted to different moisture conditions and evaluated their N contribution to the landscape level. We measured in situ N 2 fixation rates in Hylocomium splendens, Pleurozium schreberi and Sphagnum spp. from June to September in subarctic tundra in Sweden. We exposed mosses occurring along a natural precipitation gradient (mean annual precipitation: 571-1155 mm) to 8 years of experimental summer warming using open-top chambers before our measurements. We modelled species-specific seasonal N input to the ecosystem at the colony and landscape level. Higher mean annual precipitation clearly increased N 2 fixation, especially during peak growing season and in feather mosses. For Sphagnum-associated N 2 fixation, high mean annual precipitation reversed a small negative warming response. By contrast, in the dry-adapted feather moss species higher mean annual precipitation led to negative warming effects. Modelled total growing season N inputs for Sphagnum spp. colonies were two to three times that of feather mosses at an area basis. However, at the landscape level where feather mosses were more abundant, they contributed 50% more N than Sphagnum. The discrepancy between modelled estimates of species-specific N input via N 2 fixation at the moss core versus ecosystem scale, exemplify how moss cover is essential for evaluating impact of altered N 2 fixation. Importantly, combined effects of warming and higher mean annual precipitation may not lead to similar responses across moss species, which could affect moss fitness and their abilities to buffer environmental changes., (© 2024 The Author(s). Global Change Biology published by John Wiley & Sons Ltd.)

Construction of modern timber bridges has greatly increased during the last 20 years in Sweden. Wood as a construction material has several advantageous properties, e.g., it is renewable, sustainable, and aesthetically pleasing, but it is also susceptible to deterioration. To protect wood from deterioration and ensure the service life, the wood is either treated or somehow covered. This work evaluates a technology to monitor the moisture content in wood constructions. Monitoring the moisture content is important both to verify the constructive protection and for finding areas with elevated levels of moisture which might lead to a microbiological attack of the wood. In this work, a timber bridge was studied. The structure was equipped with six wireless sensors that measured the moisture content of the wood and the relative humidity every hour. Data for 744 days of the bridge are presented in this paper. Results show that the technology used to monitor the bridge generally works; however, there were issues due to communication problems and malfunction of sensors. This technology is promising for monitoring the state of wood constructions, but a more reliable sensor technology is warranted continuous remote monitoring of wood bridges over long periods of time. [ABSTRACT FROM AUTHOR]

This work investigates the prospective impacts of climate change on wind-driven rain (WDR) and walls through simulating the hygrothermal performance of rain screen of common vertical wall constructions for the climatic conditions of Gothenburg in Sweden. While a substantial amount of work has been done on the impact of climate change on the thermal performance of buildings, this paper studies its impact – through changes in rain, wind and other climatic parameters – on the amount of water which penetrates the outmost layer of ventilated façades. Importance of three uncertainty factors of the climate data are investigated: uncertainties from global climate models, emissions scenarios and spatial resolutions. Consistency of the results is examined by modelling walls with different materials and sizes, as well as using two mathematical approaches for WDR modelling. Sensitivity of the wall simulations to the wind data is assessed by using synthetic climate with sole wind data. According to the results, higher amounts of moisture will accumulate in walls in the future; climate uncertainties can cause variations up to 13% in the calculated 30-year average of water content and 28% in its standard deviation. Using sole wind data can augment uncertainties with up to 10% in WDR calculations, however it is possible to neglect changes in future wind data. [ABSTRACT FROM AUTHOR]

Abstract: The most frequently used handling method in Sweden for the extraction of forest fuels is one in which logging residues are piled in harvester heaps to dry within the clear-cutting area before stacking into larger windrows. This handling method, however, requires multiple stages and the amount of handling involved results in a significant loss of biomass that could have been used for energy. This study compares two handling methods for the extraction of logging residues in stands dominated by Norway spruce. The traditional “dried-stacked” method was compared to the “fresh-stacked” method in which logging residues are collected simultaneously during normal logging operations and stacked in windrows at or near the roadside to dry. Determination of fraction composition and moisture content was carried out on the biomass provided to the energy-converting industry shortly after comminuting the logging residues. The results show that the fresh-stacked logging residues contained a higher amount of needles (8%), compared to 4% for the dried-stacked logging residues. However, the amount of needles was considered to be low in both handling methods. Both handling methods were proven to provide adequate drying with moisture content levels at approximately 36% for fresh-stacked and 31% for dried-stacked logging residues. These results indicate that weather and forest conditions have a greater impact on the moisture content than handling method. An acceptance of fresh-stacked logging residues, preferably connected to ash recycling, would afford the energy-converting industries the opportunity to use new technologies, reduce costs and extract a greater biomass total. [Copyright &y& Elsevier]

ABSTRACT The atmospheric transport of moisture leading to extreme summer precipitation events in southern Sweden was investigated using a Lagrangian trajectory model. Surprisingly, we found that the trajectories crossed continental Europe and the Baltic Sea before arriving over Sweden; they did not arrive directly from the North Sea. Such transport pathways were not seen for a control sample of non-extreme rainfall events. We then used a new source region identification technique to investigate the hypothesis that Europe and the Baltic are important sources of the moisture that is rained out in the extreme events. Although the results varied between events, we found that this is indeed the case. Our results establish the atmospheric transport patterns that are apparently a pre-requisite for extreme rainfall events to occur in southern Sweden, and further suggest regional moisture availability may also play a key role. [ABSTRACT FROM AUTHOR]

Abstract: This study investigated feed hygiene during airtight storage of non-dried barley grain under farm conditions. Microorganisms on the grain were sampled and quantified in seven Swedish farms throughout the storage period using culture dependent methods. The dominant lactic acid bacteria (LAB) and yeasts were identified by rRNA gene sequencing and moulds by morphological characterisation. Moisture content (MC) and pH of the grain were also monitored. It was difficult to obtain the optimal MC (0.30–0.45g/g) that is necessary to initiate fermentation in the grain. Feed hygiene was maintained during storage of cereals when MC below 0.17g/g. Intermediate MC (0.17–0.23g/g) of the grains was conducive to mould growth, including growth of potential producers of mycotoxins, which can diminish feed safety and nutritional value. Enterobacteriaceae were found in all barleys, even at low MC, but their numbers were substantially decreased when the number of LAB was high. True fermentation of moist crimped cereal grains was only obtained on one farm with an initial barley MC of 0.3g/g. Here, LAB reached high numbers during storage, whereas numbers of spoilage microorganisms that may reduce feed hygiene decreased considerably. However, the pH of the barley did not differ among farms. Storage stability in airtight stored barley may thus be the result of low oxygen tension, viz. airtight storage, and competition for nutrients by the microorganisms, rather than formation of lactic acid. At harvest, Enterococcus caccae dominated the LAB population in five barleys and Lactobacillus fermentum at the remaining two. The dominant yeast species were Aureobasidium pullulans, Cryptococcus wieringae, Kazachstania aerobia and Rhodotorula glutinis. After storage, L. fermentum was dominant among the LAB. The yeast species composition was highly diverse and differed among barleys. Among others, C. wieringae, Debaryomyces hansenii, K. aerobia, R. glutinis and Sporobolomyces ruberrimus were detected. This study shows that the microbial population in airtight stored moist barley is highly diverse and not predictable. Thus, it may be necessary to influence the microbial population in the storage system by adding a starter culture. [Copyright &y& Elsevier]

Moisture problems in buildings have in a number of studies been shown to increase the risk for respiratory symptoms. The study Dampness in Buildings and Health (DBH) was initiated with the aim to identify health relevant exposures related to dampness in buildings. A questionnaire study about home environment with a focus on dampness problems and health was conducted in one county of Sweden (8,918 homes, response rate 79%). Building characteristics that were associated with one or more of the dampness indicators were for single-family houses, older houses, flat-roofed houses built in the 1960s and 1970s, houses with a concrete slab on the ground that were built before 1983. Moreover, tenancy and earlier renovation due to mould or moisture problems was strongly associated with dampness. A perception of dry air was associated with window-pane condensation, e.g. humid indoor air. [ABSTRACT FROM AUTHOR]

The Plant Protection Product Directive (91/414/EEC) stresses the need of validated models to calculate predicted environmental concentrations. The use of models has become an unavoidable step before pesticide registration. The main topic of the research presented here is the validation of the PEARL model for two well-instrumented sites located in the Netherlands and Sweden. First the water transport module was calibrated, and then the solute transport module, keeping unchanged the water transport parameters. The Dutch site is characterised by a sandy soil. PEARL predictions were very satisfactory for both soil moisture content and groundwater level. Predictions for the tracer, bentazone and ethoprophos concentrations in the soil profile were also successful. The Swedish site is characterised by a structured clay soil. PEARL was successful in predicting soil moisture profiles and the draining water. PEARL performed well in predicting the soil concentration of bentazone at different depths, however, it did not predict accurately solute concentration in the drainage water. A sensitivity analysis of the PEARL model performed on the Swedish site showed the greater importance of the pesticide degradation properties over the soil hydraulic properties. [Copyright &y& Elsevier]

Purpose - This paper sets out to look at the different types of crawl spaces that are found in Sweden and why they are still being used in today's constructions despite the advice of building experts to avoid their use. Design/methodology/approach - Literature reviews were performed to look at the types of crawl space foundations available as well as the advantages and disadvantages of each type and to look at the economic costs associated with repairing a damaged home that could be attributed to a crawl space foundation. Interviews were conducted with engineers with regard to moisture design issues in the Swedish building industry. Findings - This study shows that there are five traditional types of crawl spaces used in Sweden: plinth, outdoor ventilated, indoor ventilated, unventilated, and suspended crawl space foundations, four of which are currently available to builders. Despite all of the available knowledge regarding the disadvantages and the past performance of the outdoor ventilated crawl spaces, companies in Sweden are still using this design and are still experiencing expensive problems. Research limitations/implications - This paper is limited to Sweden. The situation in other countries was not specifically examined; however, it appears that other countries are also facing the same problems and this paper may provide some insight into why. Originality/value - This study shows that there are many ways to construct a crawl space, some of which are considerably less risky than others. The study also indicates that the building industry in general seems to lack the theoretical background or incentive to utilize these variations properly or completely move away from these designs. [ABSTRACT FROM AUTHOR]

Aim: Questionnaires are a cheap means of studying large populations but the information obtained from them is seldom validated. Earlier studies have reported both high and low levels of agreements between inspectors' observations and occupants' reports regarding home environmental factors that included moisture problems. The aim of this study was to validate information received from a questionnaire survey regarding building characteristics, mouldy odour, and signs of moisture problems in 390 Swedish homes. Method: In a case control study on the association between home environmental factors and asthma/allergy among children, 390 homes were visited by trained inspectors for ocular inspection of visible moisture damage and perceptions of mouldy odour. Their observations were then compared with questionnaire reports collected 18-24 months earlier from the families. Results: A high level of agreement was found between the inspectors' observations and the occupants' questionnaire reports on technical parameters. This included type of house, type of ventilation system, and foundation, particularly in single-family houses. There was low agreement regarding vinyl or linoleum floor coverings and indications of dampness and mouldy odour. However, the stronger the mouldy odour experienced by the inspector, the higher the level of agreement. Conclusions: The questionnaire was a quite reliable source regarding technical parameters of the home but not for dampness problems. The questionnaire was better for predicting buildings without problems than detecting problems of mouldy odour and visible indications of moisture. To increase the validity of future questionnaires, simple drawings or information on critical spots for dampness could be used. [ABSTRACT FROM AUTHOR]

ABSTRACT: Studies from recent years involving development and application of statistical downscaling models for Scandinavia (mainly Norway and Sweden) are reviewed. In most of the studies linear techniques were applied. Local temperature and/or precipitation were predictands in a majority of the studies. Large-scale temperature fields, either from 2 m or 850 hPa, were found to be the best predictors for local temperature, while a combination of atmospheric circulation indices and tropo-spheric humidity information were the best predictors for local precipitation. Statistically downscaled temperature scenarios for Scandinavia differ depending on climate model, emission scenario and downscaling strategy. There are nevertheless several common features in the temperature scenarios. The warming rates during the 21st century are projected to increase with distance from the coast and with latitude. In most of Scandinavia higher warming rates are projected in winter than in summer. For precipitation, the spread between different scenarios is larger than for temperature. A substantial part of the projected precipitation change is connected to projected changes in atmospheric circulation, which differ considerably from one model integration to another. A tendency for increased large-scale humidity over Scandinavia still implies that projections for the 21st century typically indicate increased annual precipitation. This tendency is most significant during winter. In northern Scandinavia the projections tend to show increased precipitation also during summer, but several scenarios show reduced summer precipitation in parts of southern Scandinavia. Comparisons with results from global and regional climate models indicate that both regional modeling and statistical downscaling add value to the results from the global models. [ABSTRACT FROM AUTHOR]

To make predictions of future climate it is necessary to understand the past climate—temperature as well as precipitation. While a wealth of temperature proxies exist from northern latitudes, there is still a lack of information about past precipitation variability. Here we present a 300-year-long tree-ring width chronology from xeric-site Scots pines (Pinus sylvestrisL.) in Tyresta National Park, east central Sweden. Tree-ring widths were compared to the long observed temperature and precipitation records from Stockholm during 1786–2000. Analyses of the climate/growth relationship showed that, in general, May–June precipitation had a dominating influence on pine growth. However, during dry periods, negative responses to June–July temperature were stronger, especially evident in the late nineteenth century. Periods of below-average growth were associated with dry conditions in May–June, but occasionally periods of wet and cool summers also produced narrow rings. Periods of above-average growth were linked to wet, but sporadically also cool and dry, early summers. The years between 1815 and 1833 appear to be particularly dry in the 300-year context. Since growth anomalies are found in other Swedish drought-sensitive tree-ring chronologies during this period, it is likely that this dry period had a regional extent. This is the first tree-ring chronology from southern Sweden that provides multi-century information of past summer drought and moisture variability with high resolution and the study will add important information regarding past climate variability in southern Sweden. [ABSTRACT FROM AUTHOR]

Apartments built in Sweden during the record years 1961–1975 with the aim to remedy the housing shortage and abolish poor standards, were designed for a normal-sized family of 2–4 persons. The mechanical ventilation system, if existing, was primarily designed to ensure an air exchange in the apartment according to Swedish building regulations. During the last few years, the number of overcrowded apartments has increased due to housing shortage in general but also due to migration. Another aspect is that the ventilation in many apartments built during the record years is already insufficient at normal occupant load. The question is how doubling or tripling the number of occupants and thus, the moisture load will affect the risk of bad air quality and moisture damage. To find out, simulations were made to estimate whether it is possible to obtain sufficient air quality and low risk of moisture damage by only increasing the ventilation rates in existing systems or introducing new ventilation systems with and without heat recovery and what the consequence would be in terms of the additional energy demand. Measurements from earlier studies of CO2 and moisture supply in Swedish apartment buildings were used as input data. [ABSTRACT FROM AUTHOR]