Search

Clean sampling and analysis procedures were used to quantify more than 70 inorganic constituents, including 35 potentially toxic or hazardous constituents, organic carbon, and other characteristics of untreated (influent) and treated (effluent) coal-mine discharges (CMD) at 38 permitted coal-mining or coal-processing facilities in the bituminous coalfield and 4 facilities in the anthracite coalfield of Pennsylvania. Of the 42 facilities sampled during 2011, 26 were surface mines, 11 were underground mines, and 5 were coal refuse disposal operations. Treatment of CMD with caustic soda (NaOH), lime (CaO or Ca(OH) 2 ), flocculent, or limestone was ongoing at 21%, 40%, 6%, and 4% of the facilities, respectively; no chemicals were added at the remaining facilities. All facilities with CMD treatment incorporated structures for active or passive aeration and settling of metal-rich precipitate. The untreated influent samples had wide ranges of pH (2.8–7.6), hot acidity (−600 to 8000 mg/L as CaCO 3 ), specific conductance (SC; 253–13,000 μS/cm), total dissolved solids (TDS; 168–18,100 mg/L), and associated dissolved (<0.45-μm pore-size filter) constituents, including SO 4 (14.7–10,700 mg/L), Fe (<0.01 to 4100 mg/L), Mn (0.02–136 mg/L), Al (<0.01 to 128 mg/L), and Zn (<0.003 to 18.8 mg/L). Concentrations of Ag (<1 μg/L), Hg (<1 μg/L), Sn (<0.5 μg/L), and CN (<0.01 mg/L) were below detection limits. Only one influent sample met permitted mine effluent (PME) limits plus dissolved-constituent criteria maximum concentration (CMC) thresholds for the protection of freshwater aquatic organisms. The pH of the treated effluent samples ranged from 5.5 to 11.9 and was greater than or equal to the pH of the corresponding influent at all sites. All the effluent samples met CMC levels for dissolved concentrations of Ag, As, Ba, Cd, Cl, Cr, Pb, Ni, Sb, Se, Tl, V, NH 3 , NO 2 , NO 3 , and CN; however, nine violated one or more of the PME limits for pH (<6, n = 1), net acidity (>0, n = 3), Fe (>7 mg/L, n = 1), or Mn (>5 mg/L, n = 8), plus one or more exceeded CMC levels for Al (>0.75 mg/L, n = 2), Co (>95 μg/L, n = 5), Zn (>307 μg/L, n = 1), Cu (>7.4 μg/L, n = 1), or Se (>12.8 μg/L, n = 3). Although CMC exceedances for Co and Zn were attributed to samples also violating the PME limit for pH or Mn, the samples that exceeded the CMC for Al, Cu, or Se met applicable PME limits for pH, Fe, and Mn. Furthermore, many of the pH-compliant effluents did not meet reference criteria for SO 4 and related measures of ionic strength, including TDS, SC, and osmotic pressure. The Wilcoxon matched-pair signed-ranks statistic was used to test if the overall difference between the effluent and influent pairs was equal to zero. Constituents that statistically were the same for effluent and influent ( p > 0.05) included flow rate, SC, osmotic pressure, hardness, alkalinity, total organic carbon (TOC), K, Cl, NO 3 , PO 4 , Sb, Sr, Br, Se, Mo, and V. Although temperature, dissolved oxygen, pH, Ca, and Na were greater in the effluent than the influent, most constituents decreased as a result of treatment, including TDS, acidity, SO 4 , Al, Fe, Mn, Mg, As, Ba, Be, Cd, Cr, Co, Cu, F, Pb, Ni, NH 3 , Tl, Ti, U, Zn, Zr, total phenols, total inorganic carbon (TIC), biological oxygen demand (BOD), and chemical oxygen demand (COD). Nevertheless, some constituents that decreased, such as SO 4 , still did not meet reference criteria. Findings from this study suggest that typical chemical or aerobic treatment of CMD to pH > 6 with removal of Fe to <7 mg/L and Mn to <5 mg/L may provide a reasonable measure of protection for aquatic life from priority pollutant metals and other toxic or hazardous constituents in effluent but may not be effective for achieving permissible or background levels for TDS, SC, osmotic pressure, or concentrations of SO 4 and some other pollutants, including Se, Br, and Cl, if present. [ABSTRACT FROM AUTHOR]

The variations of mechanical properties of coals in nano-to-micro scale play vital roles in defining the coal deformative and failure behaviors with a wide range of engineering applications, including coal stimulation for gas recovery and/or CO 2 sequestration in coal seams. Based on the assumption that the heterogeneity in the mechanical properties of coals is combinedly determined by the mineralogical/carbon compositions and microstructures, three coals were experimentally measured through combing nanoindentation test, X-ray diffraction (XRD) analysis and field emission scanning electron microscopy - energy dispersive spectroscopy (FESEM-EDS) imaging. Two sub-bituminous coals from Illinois basin and one bituminous coal from Pittsburgh No.8 seam from Pennsylvania were collected and prepared. The moduli, hardness, and energy dissipations were all analyzed for three coals. The mean Young's moduli and hardness of two sub-bituminous and bituminous coals are ~4.13 GPa, ~4.79 GPa, and ~ 5.56 GPa respectively and the mean hardness of which are ~0.38 GPa, ~0.49 GPa and ~ 0.58 GPa respectively. The results confirmed that the nanoscale mechanical properties are compositional and microstructural dependent. It was also observed that the heterogeneity of sub-bituminous coals is more apparent than the bituminous coal. Also, the bituminous coal is more harder and brittle than sub-bituminous coal, which can better withhold the mechanical response, but the deformations are relatively permanent due to brittle failure. The energy dissipation data showed that the irreversible work decreases with the increase in hardness, which confirmed that the plastic deformation is much more easily to be inducted. The mechanism-based phenomenon pop-in event on the load-displacement curve was also analyzed by linking with the characteristics of the morphology and composition beneath a pointed indenter or cracks formation due to the localized indent. [ABSTRACT FROM AUTHOR]

The Allegheny Plateau in western Pennsylvania, western Maryland, and northern West Virginia has relatively flat-lying strata with southwest-northeast-trending anticlines cored by splay faults originating from the thrust faults and southeast-northwest-trending lineaments. The lineaments define both the structural relief of the anticlines and the coal rank. Coal rank in the Pennsylvanian Allegheny Group coals is medium volatile bituminous in the region of less-prominent structural relief and low volatile bituminous in the region with more pronounced anticlines. Zinc and Cl exhibit high values in coals in the vicinity of the lineaments. Although coal rank was not a parameter in the Principal components analysis, the highest rank coals clustered together in a quadrant defined, in part, by the Zn concentration. Zinc was selected as a parameter due to its possible link with hydrothermal mineralization and Zr and TiO 2 /Al 2 O 3 were selected based on their presumed association with detrital mineral influences. The highest rare earths + Y values in benches of the Lower Kittanning coal were found at sites close to the lineaments. Negative or negligible Ce anomalies (δCe) and strongly positive Gd anomalies (δGd) suggest marine or hydrothermal influences and negative Eu anomalies (δEu) along with high TiO 2 /Al 2 O 3 values suggest a terrestrial input. The plots of δCe vs. δGd and δCe vs. δEu show that the low volatile bituminous coals are segregated from the other coals, suggesting that the factors that influenced coal rank also influenced the distribution of the rare earth elements. • The Allegheny Front is the eastern region of the Northern Appalachian coalfields. • For this work, the focus was on the region to the east of the Chestnut Ridge anticline. • Pottsville, Allegheny, and Conemaugh formation coals were examined. • High concentrations of Zn and Cl in coals were associated with cross-strike lineaments. • Coal rank and rare earth emplacement may have been mutually controlled. [ABSTRACT FROM AUTHOR]

Studies the extent of endomycorrhizal infection in herbaceous plants growing on an anthracite and bituminous areas in Pennsylvania. Results of field investigations; Effects of endophytes on maize growth; Comparison between anthracite and bituminous waste as growth medium.