Search

Introduction: Stray energy from surgical energy instruments can cause unintended thermal injuries. There are no published data regarding electrosurgical generators and their influence on stray energy transfer during robotic surgery. There are two approved generators for the DaVinci Xi robotic platform: a constant-voltage regulating generator (cVRG) and a constant-power regulating generator (cPRG). The purpose of this study was to quantify and compare stray energy transfer in the robotic Xi platform using a cVRG versus a cPRG. Methods: An ex vivo bovine model was used to simulate a standard multiport robotic surgery. The DaVinci Xi (Intuitive Surgical, Sunnyvale, CA) robotic platform was attached to a trainer box using robotic ports. A 5 s, open-air activation of the monopolar scissors was done with commonly used electrosurgical settings using a cPRG (ForceTriad, Covidien-Medtronic, Boulder, CO) or cVRG (ERBE VIO 300 dV 2.0, ERBE USA, Marietta, GA). Stray energy transfer was quantified as the change in tissue temperature (°C) nearest the tip of the assistance grasper (which was not in direct contact with the active monopolar scissors). Results: Stray energy transfer occurred with both generators. Utilizing common, comparable settings for standard coagulation, significantly less stray energy was transferred with the cVRG versus cPRG (4.4 ± 1.6 °C vs. 41.1 ± 13.0 °C, p < 0.001). Similarly, less stray energy was transferred using cut modes with the cVRG compared to the cPRG (5.61 ± 1.79 °C vs. 33.9 ± 18.4 °C, p < 0.001). Conclusion: Stray energy transfer increases tissue temperatures more than 45C in the DaVinci Xi robotic platform. Low voltage modalities, such as cut or blend; as well as a cVRG generator, significantly reduces stray energy. Robotic surgeons can minimize the risk of stray energy injuries by using these low risk modes and/or generator. [ABSTRACT FROM AUTHOR]

Introduction: Stray energy transfer from surgical monopolar radiofrequency energy instruments can cause unintended thermal injuries during laparoscopic surgery. Single-incision laparoscopic surgery transfers more stray energy than traditional laparoscopic surgery. There is paucity of published data concerning stray energy during single-incision robotic surgery. The purpose of this study was to quantify stray energy transfer during traditional, multiport robotic surgery (TRS) compared to single-incision robotic surgery (SIRS).Methods: An in vivo porcine model was used to simulate a multiport or single-incision robotic cholecystectomy (DaVinci Si, Intuitive Surgical, Sunnyvale, CA). A 5 s, open air activation of the monopolar scissors was done on 30 W and 60 W coag mode (ForceTriad, Covidien-Medtronic, Boulder, CO) and Swift Coag effect 3, max power 180 W (VIO 300D, ERBE USA, Marietta, GA). Temperature of the tissue (°C) adjacent to the tip of the assistant grasper or the camera was measured with a thermal camera (E95, FLIR Systems, Wilsonville, OR) to quantify stray energy transfer.Results: Stray energy transfer was greater in the SIRS setup compared to TRS setup at the assistant grasper (11.6 ± 3.3 °C vs. 8.4 ± 1.6 °C, p = 0.013). Reducing power from 60 to 30 W significantly reduced stray energy transfer in SIRS (15.3 ± 3.4 °C vs. 11.6 ± 3.3 °C, p = 0.023), but not significantly for TRS (9.4 ± 2.5 °C vs. 8.4 ± 1.6 °C, p = 0.278). The use of a constant voltage regulating generator also minimized stray energy transfer for both SIRS (0.7 ± 0.4 °C, p < 0.001) and TRS (0.7 ± 0.4 °C, p < 0.001).Conclusions: More stray energy transfer occurs during single-incision robotic surgery than multiport robotic surgery. Utilizing a constant voltage regulating generator minimized stray energy transfer for both setups. These data can be used to guide robotic surgeons in their use of safe, surgical energy. [ABSTRACT FROM AUTHOR]