Search

The Sustainable Energy Development Authority of Malaysia (SEDA) regularly receives complaints about damaged components and distribution boards of PV systems due to lightning strikes. Permanent and momentary interruptions of distribution circuits may also occur from the disturbance. In this paper, a solar PV Rooftop system (3.91 kWp) provided by SEDA was modelled in the PSCAD/EMTDC. The Heidler function was used as a lightning current waveform model to analyse the transient current and voltage at two different points susceptible to the influence of lightning events such as different lightning current wave shape, standard lightning current and non-standard lightning current. This study examines the effect on the system components when lightning directly strikes at two different points of the installation. The two points lie between the inverter and the solar PV array and between inverter and grid. Exceptionally high current and voltage due to the direct lightning strike on a certain point of a PV Rooftop system was also studied. The result of this case study is observed with and without the inclusion of surge protective devices (SPDs). The parameters used were 31 kA of peak current, 10 metres cable length and lightning impulse current wave shape of 8/20μs. The high current and voltage at P1 striking point were 31 kA and 2397 kV, respectively. As for the AC part, the current and voltage values were found to be 5.97 kA and 5392 kV, respectively.Therefore, SPDs with suitable rating provided by SEDA were deployed. Results showed that high transient current voltage is expected to clamp sharply at the values of 1.915 kV and 0 A at the P1 striking point. As for the AC part, the current and voltage values were found to be 0 kA and 0.751 V, respectively. Varying lightning impulse current wave shapes at striking point P2 showed that the highest voltage was obtained at waveshape 10/350 μs at 11277 kV followed by wave shapes of 2/70 μs, 8/20 μs and 0.7/6 μs. The high value of transient voltage was clamped at a lower level of 2.029 kV. Different lightning amplitudes were also applied, ranging from 2–200 kA selected based on the CIGRE distribution. It showed that the current and voltage at P1 and P2 were directly proportional. Therefore, the SPD will be designed at an acceptable rating and proper position of SPD installation at solar PV Rooftop will be proposed. The results obtained in this study can then be utilised to appropriately assign a SPD to protect the PV systems that are connected to the grid. Installing SPDs without considering the needs of lightning protection zones would expose the expensive equipment to potential damage even though the proper energy coordination of SPDs is in place. As such, the simulation results provide a basis for controlling the impacts of direct lightning strikes on electrical equipment and power grids and thus justify SPD coordination to ensure the reliability of the system. [ABSTRACT FROM AUTHOR]

Highlights • Several surge arrester configurations on a 132 kV double circuit transmission line were modelled. • The energy discharged by lightning strokes during back flashover phenomena was investigated. • The most effective protection design were determined based on the actual tripping pattern. • Double circuit line tripping can be completely eliminated by installing arresters at each phase. • The chosen arrester configuration provides sufficient protection to transmission lines. Abstract Surge arrester has been proven to be the most effective application to provide optimum lightning protection for the transmission line. Thus, many works on optimizing lightning protection for transmission line have been conducted since the past. However, works on minimizing double circuit outages and surge arrester physical properties during transient overvoltages are less likely to be found. Therefore, in this work, several surge arrester configurations installed on a 132 kV double circuit transmission line were modelled using EMTP-RV to investigate their capability to withstand current and energy discharged by lightning strokes during back flashover phenomena. These configurations were then compared to determine the most effective protection design based on the actual tripping pattern recorded by the lightning detection system (LDS) in Malaysia. The selection was made by considering arresters' discharge energy due to variation in tower footing resistance, current magnitude, power frequency voltage, lightning tail time and front time, number of towers and span length. It was found that double circuit transmission line tripping can be completely eliminated by installing surge arresters at each phase conductor of one circuit. The selected arresters configuration provides sufficient lightning protection to the transmission line and complies with the discharge energy capability requirement specified by the utility company in Malaysia, of 5.1 kJ/kV for maximum continuous operating voltage (MCOV). [ABSTRACT FROM AUTHOR]

• Analysis of NGLA, EGLA, and MCIA performance on mitigating double circuit tripping. • Installing four arresters per tower is the most optimal and universal solution. • All arresters are operating below manufacturers' maximum discharge energy level. • MCIA discharges 54% and 44% less energy than NGLA and EGLA respectively. • The most suitable arrester was selected based on the proposed protocol. Direct lightning strikes on overhead lines and towers causes power system outages. Optimal surge arrester placement is a practical and economical protection technique. From research trends, three types of transmission line arresters are in practice: Non-Gapped Line Arrester (NGLA), Externally Gapped Line Arrester (EGLA) and Multi Chamber Insulator Arrester (MCIA). This study proposed a simplified guide for selecting the most suitable line arrester considering the placement configurations, double circuit outage prevention and energy capabilities. Electromagnetic Transient Program was implemented to analyze back flashover performance of a typical 275 kV double circuit transmission line in Malaysia. Critical flashover parameters considered are lightning current magnitude, tower footing resistance, and power frequency angle. Analyzed results from the three arresters found that installing four arresters, two per circuit, at the lower and upper phases respectively, is the most optimal and universal double outage mitigation technique. Energy comparison reveals that MCIA discharges 54% and 44% less energy than NGLA and EGLA respectively. Also, from 132 kV system results, MCIA discharges 74% and 22% lesser energy respectively. From further validation of the simulation model, NGLA discharged 23.8% more energy than EGLA from experimental results. The proposed guide is applicable to double circuit lines below 275 kV. [ABSTRACT FROM AUTHOR]

Tropical countries with extensive lightning activity, such as Malaysia, encounter numerous problems on their electrical transmission and distribution systems. Many overhead lines trip because of back flashover of lightning and shielding failures of the grounding system. To overcome the problem and improve transmission line performance, a detailed lightning study is required to analyse the corresponding lines and determine the best location for transmission line arrester (TLA) installation. We used TFlash to analyse a TLA installation on a 132-kV SSWW-BBST overhead transmission line system located in Selangor, Malaysia. Based on the results, the installation of the TLA at the optimum quantity and at appropriate towers have reduced the number of lines that trip. [ABSTRACT FROM AUTHOR]

To the electric utility engineer, the parameters of the flash that are of primary interest are the crest current for the first and subsequent strokes, the waveshape of these currents, correlation between the parameters, the number of strokes per flash and flash incidence rates where the ground flash density, denoted as flashes per square km-year and symbolized by Ng. The first three parameters, as we know them today, are to a very large extent based on the measurements of Berger. Berger's masts, 70 and 80 meters high, were mounted atop Mt. San Salvatore (Switzerland), which is 650 meters above Lake Lugano, where it can be readily noted that these 125 records represent one of the best and most extensive set of data available to the industry to date. This paper focuses on the lightning severity scenario in Malaysia, which could also applicable to other tropic countries, and some of the useful parameters for lightning protection system design and forensic study. Some specific engineering applications have also been summarised, taking into account various lightning parameters, available from past and current measurements. [ABSTRACT FROM AUTHOR]

Unplanned electrical power outages are a major concern to power utilities throughout the whole world. Unfortunately, power outages will continue to occur and they cannot be fully prevented. It could be the result of lightning strikes, tree encroachment, or equipment failure. However, the impact can be reduced if power system operators are equipped with the appropriate tools to analyze the root cause of the failure. Without sufficient tools to identify the nature of a fault, the restoration process could be delayed because the operator does not know whether it is safe to normalize the isolated line. This paper describes the new and simplified fault signature analysis approach on Tenaga Nasional Berhad using a digital fault recorder. The research focuses on the contribution of the lightning strike and tree encroachment to the overhead line tripping in Malaysia. [ABSTRACT FROM AUTHOR]