Search

The reduction of nitroarenes to arylamines is a synthetically important transformation both in the laboratory and in industry. Herein, Palladium (Pd) nanoparticles were synthesized via incorporation with mesoporous fumed silica material by doping technique. Water was used as a solvent and the as-synthetized material was reduced by using NaBH4 to ensure the total transformation of PdO into Pd nanoparticles. The synthesized sample was characterized by using inductively coupled plasma (ICP) elemental analysis, X-ray powder diffraction (XRD), N2 sorption measurement, scanning electron microscope (SEM), energy-dispersive spectroscopy (EDX), and transmission electron microscopy (TEM). Data showed that the Pd nanoparticles were successfully synthesized and supported on the mesoporous silica with an average size in the ranges of 10–20 nm, with an irregular shape. The purity of the synthesized sample was confirmed by EDX analysis which exhibits the presence of Si, O, and Pd. The catalytic activity of the prepared sample was evaluated in the heterogeneous reduction of nitroarenes to aromatic amines. Reduction reaction was monitored by Shimadzu GC-17A gas chromatography (GC, Japan) equipped with flam ionization detector and RTX-5 column, 30 m × 0.25 mm, 1-μm film thickness. Helium was used as carrier gas at flow rate 0.6 mL/min. Interestingly, the green hydrogenation of nitroarenes to primary amine compounds was achieved in an aqueous solution with high efficiency and in a short time; moreover, the reusability of heterogeneous Pd-SiO2 was performed for four repeated cycles with more than 88% of efficiency at the fourth run. Finally, the heterogeneity of catalysis with high reliability and eco-friendly processes is a super new trend of nitroarenes reduction in the industry and economic scales. [ABSTRACT FROM AUTHOR]

The removal of Zn from wastewater generated from the Zn-based electroplating manufacturing process is essential because the regulation limit of Zn concentration in wastewater is becoming stricter in Japan. However, achieving this through conventional methods is difficult, especially for small and medium enterprises in the plating industry. Therefore, a suitable Zn-removal method with a low cost but high performance and Zn selectivity is required. The application of adsorbents is one possible solution. Mesoporous silica (MS) is a well-known adsorbent with controllable pore size, high specific surface area (SSA), high acid resistance, and ease of surface modification. In this study, we modified the surfaces of MSs with different initial pore sizes by amino groups and investigated their Zn removal performances. The effect of pore size on amine modification using (3-aminopropyl)triethoxysilane and on adsorption performance in a single system was investigated along with Zn adsorption selectivity in the Zn–Ni binary system. Amine-modified MS prepared from MS with an initial pore size of 1.9 nm showed drastically lower performance compared to those prepared from MS with an initial pore size larger than 2.8 nm. Zn-selectivity in the Zn–Ni binary system, containing equal amounts of Zn and Ni, was found to reach a maximum of 21.6 when modifying MS with an initial pore size of 2.8 nm. [ABSTRACT FROM AUTHOR]

Mesoporous silica was successfully synthesized for the first time using geothermal water from the Onuma Geothermal Power Plant, Akita Prefecture, Japan. Cetyltrimethylammonium bromide (CTAB) was used as an organic template for the synthesis. CTAB with a concentration of 2.4 × 10–4 mol/L was reacted for 30 min with geothermal water at a temperature of 90 °C, which had a total silicic acid concentration of 475 mg/L (SiO2), at pH 7.0, pH 8.2 (raw water) and pH 9.0. By calcination of the resulting precipitate at 550 °C, mesoporous silica with a pore size of about 2.8 nm and a specific surface area of > 800 m2/g was formed. The total silicic acid concentration in the solution after formation of the mesoporous precipitates was reduced to < 280 mg/L, indicating efficient recovery of supersaturated silicic acid from geothermal water. The monosilicic acid in geothermal water plays an important role in the formation of mesoporous silica. Production of mesoporous silica by our method will contribute not only to prevention of silica scale formation in the piping systems of geothermal power plants but also to its use as an industrial resource. [ABSTRACT FROM AUTHOR]