Search

The Tournemire Underground Research Laboratory (Aveyron, France), developed by the French Institute for Radiological Protection and Nuclear Safety, is composed of a tunnel excavated in an argillaceous geological layer belonging to a limestone–argillite–limestone sub-horizontal sedimentary sequence. Sub-vertical fault zones are intercepted by drifts and boreholes excavated from the tunnel in the argillaceous layer at a depth of about 250 m. These fault zones are characterized by velocities lower than those of the embedding rocks. In this study, we assess the capacity of first arrival traveltime tomography to detect and characterize such fault zones in a surface-to-depth transmission configuration with a limited angle aperture. The source at the surface is a sledgehammer and turns out to be very repetitive. The source trigger is transmitted to the acquisition bay via a VHF transmitter. Receivers are located at depth in underground works. First arrivals are clear and traveltime picking is straightforward. Before inverting real data, we conduct synthetic tests with the real acquisition geometry to assess limits and validity of first arrival traveltime tomography to detect a lower velocity fault zone using different initial configurations and inversion constraints during the inversion. We show that introducing a priori information on velocities in the shallow subsurface, limestones and argillaceous layers and constraints on maximum velocities greatly helps improving results and subsequent interpretation. Velocities obtained from the real data display a main lower velocity zone that extends from the galleries in the argillaceous layer right up to the surface in limestones. The location and extension of this lower velocity zone are consistent with fault and fracture zones mapped from geological observations. [ABSTRACT FROM AUTHOR]

The Experimental platform of Tournemire (Aveyron, France) developed by IRSN (French Institute for Radiological Protection and Nuclear Safety) is located in a tunnel excavated in a clay-rock formation interbedded between two limestone formations. A well-identified regional fault crosscuts this subhorizontal sedimentary succession, and a subvertical secondary fault zone is intercepted in the clay-rock by drifts and boreholes in the tunnel at a depth of about 250 m. A 2D electrical resistivity survey was carried out along a 2.5 km baseline, and a takeout of 40 m was used to assess the potential of this method to detect faults from the ground surface. In the 300 m-thick zone investigated by the survey, electrical resistivity images reveal several subvertical low-resistivity discontinuities. One of these discontinuities corresponds to the position of the Cernon fault, a major regional fault. One of the subvertical conductive discontinuities crossing the upper limestone formation is consistent with the prolongation towards the ground surface of the secondary fault zone identified in the clay-rock formation from the tunnel. Moreover, this secondary fault zone corresponds to the upward prolongation of a subvertical fault identified in the lower limestone using a 3D high-resolution seismic reflection survey. This type of large-scale electrical resistivity survey is therefore a useful tool for identifying faults in superficial layers from the ground surface and is complementary to 3D seismic reflection surveys. [ABSTRACT FROM AUTHOR]

We present here a detailed analysis of a seismic data set recorded by a dense seismological network installed over 6 months in the southeast of France. This experiment was set-up at the boundary between the Ligurian basin and the southern subalpine thrust belt (the Nice arc), which is a complex tectonic region that undergoes low to moderate seismicity. We recorded more than 500 microearthquakes, among which 348 occurred exactly in the centre of the network during a very active seismic sequence that lasted mainly over 2 months. We performed an absolute location of all of the events and calculated the magnitudes. Then we applied a cross-correlation technique to gather similar events and to relocate relatively few of them. This method revealed a very clear alignment of 19 events in a direction N120° oblique to the N20° general trend of seismicity. Focal mechanisms were determined for the four largest events and composite solutions for 32 smaller ones. Both the alignments of the earthquakes and the focal solutions revealed that two oblique segments of the fault were activated during the crisis. The main segment (8 km long) that was oriented NNE with a left-lateral strike slip movement is called the Blausasc fault. Taking into account the tectonic evolution and the relationships between surface structures and the distribution of earthquakes, and through a paleaoreconstruction of the tectonic evolution, we propose that the Blausasc fault is the hidden root of the Peille-Laghet fault, which has a mapped length of at least 15 km. The smaller segment (0.6 km long) that was activated during the crisis could be interpreted as an antithetic Riedel fracture. The active Blausasc fault is located in a densely populated zone, at only 10 km from the crowded cities of Monaco and Nice. It is thus particularly interesting to analyse it for hazard assessment. In the last section, we present a simulation that is aimed at predicting what the ground motion in the city of Nice would be like if an earthquake of magnitude 5.7 occurs on this fault. For this, we used the recordings of the largest event of the seismic sequence ( Ml= 3.2) and an empirical Green's function summation scheme to simulate the ground motion at two stations situated in urban environments. The values obtained show that especially on soft soil sites, the effects of such an earthquake would be considerable in the city of Nice. [ABSTRACT FROM AUTHOR]