Search

Orienting polymer semiconductors is desirable to optimize device characteristics, provide insight into microstructure, and magnify subtle phase behavior. Here, a combination of uniaxial strain and subsequent heating of the donor–acceptor (DA) polymer PBnDT‐FTAZ is discovered to lead to exceptional optical dichroic ratios of up to 38 (and close to 50 near the polymer's absorption edge). This alignment is achieved due to the existence of a previously undetected thermotropic liquid crystal (LC) mesophase. The LC transition, not discernable through calorimetry, is uncovered through a combination of in situ UV–vis spectroscopy, X‐ray scattering, and dynamic mechanical analysis (DMA). Comparing PBnDT‐FTAZ to the non‐fluorinated PBnDT‐HTAZ and the homo polymer PBnDT, all of which show similar thermal transitions, reveals that exceptional alignment is only found in PBnDT‐FTAZ. This is attributed to the PBnDT‐FTAZ film having two distinct liquid crystal populations, and the polymer templating to a highly aligned, high‐clearing temperature population when heated. The DMA thermal relaxation behavior observed here is also seen in other DA conjugated polymers suggesting that such thermotropic LC mesophases may be common in these materials. These findings demonstrate a polymer semiconductor with remarkable alignment and uncover phase behavior with broad implications for process‐structure‐property relationships in polymer semiconductors. [ABSTRACT FROM AUTHOR]

Due to a general paucity of suitable characterization methods, the internal orientational ordering of polymer fibrils has rarely been measured despite its importance particularly for semi‐conducting polymers. An emerging tool with sensitivity to bond orientation is polarized resonant soft X‐ray scattering (P‐RSoXS). Here, P‐RSoXS reveals the molecular arrangement within fibrils (if type I or type II fibrils), the extent of orientation in the fibril crystal, and an explicit crystal‐amorphous interphase. Neat films as well as binary blends with a fullerene derivative are characterized for three different polymers, that are prototypical materials widely used in organic electronics applications. Anisotropic P‐RSoXS patterns reveal two different fibril types. Analysis of the q‐dependence of the anisotropy from simulated and experimental scattering patterns reveal that neat polymer fibrillar systems likely comprise more than two phases, with the third phase in addition to crystal and amorphous likely being an interphase with distinct density and orientation. Intriguingly, the fibril type correlates to the H‐ or J‐aggregation signature in ultraviolet‐visible (UV–vis) spectroscopy, revealing insight into the fibril formation. Together, the results will open the door to develop more sophisticated structure‐function relationships between chemical design, fibril type, formation pathways and kinetics, interfacial ordering, and eventually device functions. [ABSTRACT FROM AUTHOR]

Thermal transition of organic solar cells (OSCs) constituent materials are often insufficiently researched, resulting in trial‐and‐error rather than rational approaches to annealing strategies to improve domain purity to enhance the power conversion efficiency. Despite the potential utility, little is known about the thermal transitions of the modern high‐performance acceptors Y6 and N3. Here, by using an optical method, it is discovered that the acceptor N3 has a clear solid‐state aggregation transition at 82 °C. This unusually low transition not only explains prior optimization protocols, but the transition informs and enables a double‐annealing method that can fine‐tune aggregation and the device morphology. Compared with 16.6% efficiency for PM6:N3:PC71BM control devices, higher efficiency of 17.6% is obtained through the improved protocol. Morphology characterization with x‐ray scattering methods reveals the formation of a multilength scale morphology. Moreover, the double‐annealing method is illustrated and easily transferred and validated with Y6‐based devices, using the transition of Y6 at 102 °C. As a result, the PCE improved from 16.0% to 16.8%. Design of high‐performance acceptors with yet lower aggregation transitions might be required for OSCs to successfully transition to low thermal budget industrial processing methods where annealing temperatures on plastic substrates have to be kept low. [ABSTRACT FROM AUTHOR]

Even though significant breakthroughs with over 18% power conversion efficiencies (PCEs) in polymer:non‐fullerene acceptor (NFA) bulk heterojunction organic solar cells (OSCs) have been achieved, not many studies have focused on acquiring a comprehensive understanding of the underlying mechanisms governing these systems. This is because it can be challenging to delineate device photophysics in polymer:NFA blends comprehensively, and even more complicated to trace the origins of the differences in device photophysics to the subtle differences in energetics and morphology. Here, a systematic study of a series of polymer:NFA blends is conducted to unify and correlate the cumulative effects of i) voltage losses, ii) charge generation efficiencies, iii) non‐geminate recombination and extraction dynamics, and iv) nuanced morphological differences with device performances. Most importantly, a deconvolution of the major loss processes in polymer:NFA blends and their connections to the complex BHJ morphology and energetics are established. An extension to advanced morphological techniques, such as solid‐state NMR (for atomic level insights on the local ordering and donor:acceptor ππ interactions) and resonant soft X‐ray scattering (for donor and acceptor interfacial area and domain spacings), provide detailed insights on how efficient charge generation, transport, and extraction processes can outweigh increased voltage losses to yield high PCEs. [ABSTRACT FROM AUTHOR]

Abstract: Despite the rapid development of nonfullerene acceptors (NFAs), the fundamental understanding on the relationship between NFA molecular architecture, morphology, and device performance is still lacking. Herein, poly[[4,8‐bis[5‐(2‐ethylhexyl)thiophene‐2‐yl]benzo[1,2‐b:4,5‐b0]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]‐thieno[3,4‐b]thiophenediyl]] (PTB7‐Th) is used as the donor polymer to compare an NFA with a 3D architecture (SF‐PDI4) to a well‐studied NFA with a linear acceptor–donor–acceptor (A–D–A) architecture (ITIC). The data suggest that the NFA ITIC with a linear molecular structure shows a better device performance due to an increase in short‐circuit current (  Jsc) and fill factor (FF) compared to the 3D SF‐PDI4. The charge generation dynamics measured by femtosecond transient absorption spectroscopy (TAS) reveals that the exciton dissociation process in the PTB7‐Th:ITIC films is highly efficient. In addition, the PTB7‐Th:ITIC blend shows a higher electron mobility and lower energetic disorder compared to the PTB7‐Th:SF‐PDI4 blend, leading to higher values of Jsc and FF. The compositional sensitive resonant soft X‐ray scattering (R‐SoXS) results indicate that ITIC molecules form more pure domains with reduced domain spacing, resulting in more efficient charge transport compared with the SF‐PDI4 blend. It is proposed that both the molecular structure and the corresponding morphology of ITIC play a vital role for the good solar cell device performance. [ABSTRACT FROM AUTHOR]

Abstract: Nonfullerene polymer solar cells (PSCs) based on polymer donors and nonfullerene small molecular acceptors (SMAs) have recently attracted considerable attention. Although much of the progress is driven by the development of novel SMAs, the donor polymer also plays an important role in achieving efficient nonfullerene PSCs. However, it is far from clear how the polymer donor choice influences the morphology and performance of the SMAs and the nonfullerene blends. In addition, it is challenging to carry out quantitative analysis of the morphology of polymer:SMA blends, due to the low material contrast and overlapping scattering features of the π–π stacking between the two organic components. Here, a series of nonfullerene blends is studied based on ITIC‐Th blended with five different donor polymers. Through quantitative morphology analysis, the (010) coherence length of the SMA is characterized and a positive correlation between the coherence length of the SMA and the device fill factor (FF) is established. The study reveals that the donor polymer can significantly change the molecular ordering of the SMA and thus improve the electron mobility and domain purity of the blend, which has an overall positive effect that leads to the enhanced device FF for nonfullerene PSCs. [ABSTRACT FROM AUTHOR]

Significant efforts have lead to demonstrations of nonfullerene solar cells (NFSCs) with record power conversion efficiency up to ≈13% for polymer:small molecule blends and ≈9% for all-polymer blends. However, the control of morphology in NFSCs based on polymer blends is very challenging and a key obstacle to pushing this technology to eventual commercialization. The relations between phases at various length scales and photovoltaic parameters of all-polymer bulk-heterojunctions remain poorly understood and seldom explored. Here, precise control over a multilength scale morphology and photovoltaic performance are demonstrated by simply altering the concentration of a green solvent additive used in blade-coated films. Resonant soft X-ray scattering is used to elucidate the multiphasic morphology of these printed all-polymeric films and complements with the use of grazing incidence wide-angle X-ray scattering and in situ spectroscopic ellipsometry characterizations to correlate the morphology parameters at different length scales to the device performance metrics. Benefiting from the highest relative volume fraction of small domains, additive-free solar cells show the best device performance, strengthening the advantage of single benign solvent approach. This study also highlights the importance of high volume fraction of smallest domains in printed NFSCs and organic solar cells in general. [ABSTRACT FROM AUTHOR]

Morphology can play a critical role in determining function in organic photovoltaic (OPV) systems. Recently molecular acceptors have showed promise to replace fullerene derivatives as acceptor materials in bulk heterojunction solar cells and have achieved >10% efficiencies in single junction devices. The nearly identical mass/electron densities between the donor (polymer) and acceptor (molecule) materials results in poor material contrast compared to fullerene-based OPVs and therefore morphology characterization using techniques that rely on mass/electron density variations poses a challenge. This inhibits a fundamental understanding of the structure–property relationships for non-fullerene acceptor materials. We demonstrate that low angle annular dark field scanning transmission electron microscopy and resonant soft X-ray scattering form a set of complementary tools that can provide quantitative characterization of fullerene as well as non-fullerene based organic photovoltaic systems. [ABSTRACT FROM AUTHOR]

A general impact of solution shearing on molecular orientation correlation is observed in polymer:fullerene organic solar cells in which one of the components forms fibrils or aggregates. Further investigation with polarized soft X-ray scattering reveals that solution shearing induces more face-to-face orientation relative to the interface of two components compared to spin-coating. This impact is shearing speed dependent, that is, slow shearing speed can induce more face-to-face orientation than a fast shearing speed. These results demonstrate that solution shearing is an effective method to control the relative molecular orientation. Solution shearing can also modify the domain size and average composition variations. [ABSTRACT FROM AUTHOR]

An alkylated semiconducting polymer comprising alternating bithiophene-[all]- S, S-dioxide and aromatic monothiophene units in the polymer backbone was synthesized with the intent of modifying the energy gap and lowest unoccupied molecular orbital for use as a stable n-type semiconductor. Films spun from this semiconducting polymer were characterized utilizing X-ray scattering, near edge X-ray absorption fine structure spectroscopy, ultraviolet photoelectron spectroscopy, and thin-film field effect transistors to determine how oxidation of the thiophene ring systems impacts the structural and electronic properties of the polymer. The thiophene- S,S-dioxide polymers have lower optical and electrical band gaps than corresponding thiophene polymers. X-ray scattering results indicate that the polymers are well ordered with the π-π stacking distances increased by 0.4 Å relative to analogous thiophene polymers. The electrical stability of these polymers is poor in transistors with a drop in the field effect mobility by approximately one order of magnitude upon addition of just 5% of the thiophene- S, S-dioxide unit in a copolymer with thiophene. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013 [ABSTRACT FROM AUTHOR]

The utilization of near edge x-ray absorption fine structure spectroscopy (NEXAFS) in achieving strong, novel contrast for soft x-ray microscopy and scattering methods has been afforded significant success in elucidating outstanding issues in organic materials systems due to the unique combination of high sensitivity to chemical functionality and thus composition, moderately high spatial resolution and moderate radiation damage. We illustrate the basic operating principles of NEXAFS spectroscopy, scanning transmission x-ray microscopy, and resonant soft x-ray scattering, and exemplify the impact by discussing a few recent applications. The focus of this perspective will be the characterization of synthetic organic materials, with a further emphasis on applications involving semi-conducting polymers. We also provide a brief perspective of future instrument and method developments. [Copyright &y& Elsevier]

Abstract: Near Edge X-ray Absorption Fine Structure (NEXAFS) spectromicroscopy, resonant scattering and resonant reflectivity are specialized, synchrotron radiation based, soft X-ray characterization tools that provide moiety-specific contrast and either real-space imaging at ∼30nm spatial resolution, or scattering signals which can be inverted to provide chemically sensitive information at an even higher spatial resolution (<5nm). These X-ray techniques complement other real and reciprocal space characterization tools such as various microscopies and conventional electron, X-ray and neutron scattering. We provide an overview of these synchrotron based tools, describe their present state-of-the-art and discuss a number of applications to exemplify their unique aspects. [Copyright &y& Elsevier]

The application of resonant soft x-ray scattering to chemically heterogeneous soft condensed matter materials is presented. Two structured styrene-acrylic polymer composite latex particles ∼230 nm in diameter were utilized to delineate the potential utility of this technique. Angular scans at photon energies corresponding to strong scattering contrast between specific chemical moieties made it possible to infer the effective radii that correspond to the two polymer phases in the nanoparticles. The results show that resonant soft x-ray scattering should be a powerful complementary tool to neutron and hard x-ray scattering for the characterization of structured soft condensed matter nanomaterials. [ABSTRACT FROM AUTHOR]

The article offers information about the topics and events transpired during the soft X-ray scattering for nanoscale structure and dynamics workshop in Berkeley, California. The workshop's aim is to explore the status and potential of angle-resolved, soft X-ray scattering to yield structural information in a different settings. The workshop highlights several talks which discussed nonscale phase separation in disordered polyurethane films and in ordered diblock copolymer films.

On page 3131, Z. Bao, H. Ade, and colleagues demonstrate that the solution shearing can control molecular orientation at donor/acceptor interface of BHJ organic solar cells with polarized soft X‐ray scattering. This effect is further extended to binary organic blend in which one of the components forms fibrils or aggregates. [ABSTRACT FROM AUTHOR]

We review the Stille coupling synthesis of P(DPP2OD-T) (Poly[[2,5-di(2-octyldodecyl)pyrrolo[3,4-c]pyrrole-1,4(2H,5H)-dione-3,6-diyl]-alt-[2,2':5',2"-terthiophene-5,5"-diyl]]) and show that high-quality, high molecular weight polymer chains are already obtained after as little as 15 min of reaction time. The results of UV-vis spectroscopy, grazing incidence wide-angle X-ray scattering (GIWAXS), and atomic force microscopy show that longer reaction times are unnecessary and do not produce any improvement in film quality. We achieve the best charge transport properties with polymer batches obtained from short reaction times and demonstrate that the catalyst washing step is responsible for the introduction of charge-trapping sites for both holes and electrons. These trap sites decrease the charge injection efficiency, strongly reducing the measured currents. The careful tuning of the synthesis allows us to reduce the reaction time by more than 100 times, achieving a more environmentally friendly, less costly process that leads to high and balanced hole and electron transport, the latter being the best reported for an isotropic, spin-coated DPP polymer. [ABSTRACT FROM AUTHOR]

Solution processable conjugated organic materials have gained tremendous interest motivated by their potential of low cost, lightweight and especially easy manufacturing of large-area and flexible electronics. Toxic halogen-containing solvents have been widely used in the processing of organic electronics, particularly organic photovoltaics (OPVs). To transition this technology to more commercially attractive manufacturing approaches, removing these halogenated solvents remains one of the key challenges. Our morphological (hard/soft X-ray scattering) and calorimetric characterizations reveal that using o-methylanisole, a certified food additive, as processing solvent can achieve similar crystalline properties and domain spacing/purity with that achieved by widely used binary halogenated solvents (chlorobenzene and 1,8-diiodooctane), thus yielding comparable photovoltaic performance in spin-casted films. To move a step forward, we further present the potential of o-methylanisole as processing solvent in the blade-coating of several cases of OPVs in air. Remarkably, this single nonhazardous solvent yields ∼8.4% and ∼5.2% efficiency in OPVs by respectively blade-coating PBDT-TSR:PC71BM and all-polymeric PBDT-TS1:PPDIODT in ambient air, which are among the highest values for the respective kind of device. We postulate this simple nonhazardous solvent approach will also be applicable in the large area roll-to-roll coating and industrial scale printing of high-efficiency OPVs in air. [ABSTRACT FROM AUTHOR]

All-polymer solar cells (All-PSCs) are of great interest as a renewable and economically viable energy technology, which has shown potential advantages in practical photovoltaic applications due to the highly tunable optical, electronic, and mechanical properties. A quantitative understanding of the domain composition variations and orientational ordering of all-polymeric films affected by solvent additives had been unattainable until now. This study demonstrates how the use of trace amount solvent additive can indeed manipulate domain purity and molecular orientational ordering as revealed by polarized soft X-ray scattering (P-SoXS). Additionally, the BDDT/PNDI all-polymeric blend exhibits enhanced average domain purity with the use of a trace amount of solvent additive and thus improved charge mobility, device fill factor and power conversion efficiency. A high power conversion efficiency of ∼7.1% was obtained in the All-PSC mainly contributed by this morphology control strategy. Manipulation of domain purity and orientation ordering, both of which are impacted by the aggregation kinetics, may be a key to further boost the efficiency of new fullerene-free solar cells and all-anisotropic materials-based devices. [ABSTRACT FROM AUTHOR]

The internal structures of thin films, particularly interfaces between different materials, are critical to system properties and performance across many disciplines, but characterization of buried interface topography is often unfeasible. In this work, we demonstrate that grazing resonant soft x-ray scattering (GRSoXS), a technique measuring diffusely scattered soft x rays from grazing incidence, can reveal the statistical topography of buried thin-film interfaces. By controlling and predicting the x-ray electric field intensity throughout the depth of the film and simultaneously the scattering contrast between materials, we are able to unambiguously identify the microstructure at different interfaces of a model polymer bilayer system. We additionally demonstrate the use of GRSoXS to selectively measure the topography of the surface and buried polymer-polymer interface in an organic thin-film transistor, revealing different microstructure and markedly differing evolution upon annealing. In such systems, where only indirect control of interface topography is possible, accurate measurement of the structure of interfaces for feedback is critically important. While we demonstrate the method here using organic materials, we also show that the technique is readily extendable to any thin-film system with elemental or chemical contrasts exploitable at absorption edges. [ABSTRACT FROM AUTHOR]

Molecular miscibility is a defining property of mixtures of electron-donating polymers and electron-accepting fullerenes used in the photoactive layer of bulk heterojunction (BHJ) organic solar cells. Even though miscibility of fullerene in the polymer is a commonly observed property, quantitative measurements have unknown connections with other morphological properties such as domain size and domain purity. By varying the amount of fullerene loading in BHJ thin films, we show that morphological properties are related to miscibility via straightforward relationships. In particular, miscibility influences the sensitivity of domain spacing to fullerene loading and determines the domain volume fractions and the residual fullerene content in the mixed polymer-rich phase in devices. Not only does this work show the relationships between miscibility and morphology, but it also highlights the general importance in determining miscibility levels in BHJ systems in order to target optimum morphologies and domain purities. [ABSTRACT FROM AUTHOR]

A practical and accurate method to obtain the index of refraction, especially the decrement δ, across the carbon 1s absorption edge is demonstrated. The combination of absorption spectra scaled to the Henke atomic scattering factor database, the use of the doubly subtractive Kramers-Kronig relations, and high precision specular reflectivity measurements from thin films allow the notoriously difficult-to-measure δ to be determined with high accuracy. No independent knowledge of the film thickness or density is required. High confidence interpolation between relatively sparse measurements of δ across an absorption edge is achieved. Accurate optical constants determined by this method are expected to greatly improve the simulation and interpretation of resonant soft x-ray scattering and reflectivity data. The method is demonstrated using poly(methyl methacrylate) and should be extendable to all organic materials. [ABSTRACT FROM AUTHOR]