5 results on '"Mclaury, B. S."'
Search Results
2. Experimental Characterization of Vertical Gas-Liquid Pipe Flow For Annular and Liquid Loading Conditions Using Dual Wire-Mesh Sensor
- Author
-
Vieira, R. E., Parsi, M., Torres, C. F., Mclaury, B. S., Shirazi, S. A., Schleicher, E., and Hampel, U.
- Subjects
gas-liquid flow ,void fraction ,flow visualization ,phase distribution ,Wire-mesh sensor - Abstract
In gas well production, liquid is produced in two forms, droplets entrained in the gas core and liquid film flowing on the tubing wall. For most of the gas well life cycle, the predominant flow pattern is annular flow. As gas wells mature, the produced gas flow rate reduces decreasing the liquid carrying capability initiating the condition where the liquid film is unstable and flow pattern changes from fully cocurrent annular flow to partially cocurrent annular flow. The measurement and visualization of annular flow and liquid loading characteristics is of great importance from a technical point of view for process control or from a theoretical point of view for the improvement and validation of current modeling approaches. In this experimental investigation, a Wire-Mesh technique based on conductance measurements was applied to enhance the understanding of the air-water flow in vertical pipes. The flow test section consisting of a 76 mm ID pipe, 18 m long was employed to generate annular flow and liquid loading at low pressure conditions. A 16×16 wire configuration sensor is used to determine the void fraction within the cross-section of the pipe. Data sets were collected with a sampling frequency of 10,000 Hz. Physical flow parameters were extracted based on processed raw measured data obtained by the sensors using signal processing. In this work, the principle of Wire-Mesh Sensors and the methodology of flow parameter extraction are described. From the obtained raw data, time series of void fraction, mean local void fraction distribution, characteristic frequencies and structure velocities are determined for different superficial liquid and gas velocities that ranged from 0.005 to 0.1 m/s and from 10 to 40 m/s, respectively. In order to investigate dependence of liquid loading phenomenon on viscosity, three different liquid viscosities were used. Results from the Wire-Mesh Sensors are compared with results obtained from previous experimental work using Quick Closing Valves and existing modeling approaches available in the literature.
- Published
- 2015
3. Experimental Investigation of the Effect of 90 Degrees Standard Elbow on Horizontal Gas-Liquid Stratified and Annular Flow Characteristics using Dual Wire Mesh Sensors
- Author
-
Vieira, R. E., Kesana, N. R., Torres, C. F., Mclaury, B. S., Shirazi, S. A., Schleicher, E., and Hampel, U.
- Subjects
Wire-Mesh Sensor ,two-phase flow ,void fraction ,flow visualization - Abstract
Fluid flowing through pipelines often encounters fittings such as elbows. Although it is true that two-phase flow patterns observed in elbows are qualitatively the same as those seen in straight pipes, the presence of a pipe elbow can modify relative positions and local velocities of the two phases as they are subjected to forces in addition to those encountered in a straight pipe. That redistribution can affect pressure drop values, chemical inhibitor concentration and distribution to the top of the pipe, as well as the erosion pattern occurring from solid particles such as sand that is entrained in oil and gas transportation pipelines. In this work, a Wire-Mesh Sensor technique based on conductance measurements of void fraction was applied to investigate two-phase pipe flow through a standard elbow. The horizontal flow test section, consisting of a 76 mm ID, 18 m long pipe, was employed to generate stratified-wavy and annular flow conditions. Two 16×16 Wire-Mesh configuration sensors were positioned either 0.9 m upstream or 0.6 m downstream of the bend. The experiments were conducted at different liquid and gas superficial velocities that ranged from 0.03 m/s to 0.2 m/s and from 9 m/s to 34 m/s, respectively. The effects of liquid viscosity on the measured parameters are also investigated using two different viscosities of 1 and 10 cP. Stratified-slug transition, stratified wavy and annular flow patterns were observed visually in the clear section placed upstream of the Wire-Mesh sensors. Analysis of time series void fraction data from the dual Wire-Mesh sensors allows the determination of mean void fraction, local time average void fraction distribution, liquid phase distribution around the tube periphery, interfacial structure velocities, as well as Probability Density Function characteristic signatures within the cross-section of pipe before and after the elbow. The results indicate that the distribution of gas and liquid phases and interfacial velocities are significantly altered even 20 diameters downstream of the elbow.
- Published
- 2014
4. Characterizing Slug/Churn Flow using Wire-Mesh Sensor
- Author
-
Parsi, M., Vieira, R. E., Torres, C. F., Kesana, N. R., Mclaury, B. S., Shirazi, S. A., Schleicher, E., and Hampel, U.
- Subjects
Wire-Mesh Sensor ,slug flow ,muliphase flow ,churn flow - Abstract
A wire mesh sensor (WMS) is an intrusive device used to investigate multi-phase flows. The WMS measures the instantaneous local electrical conductivity of multiphase flows at different measuring points. There is a significant difference in the electrical conductivity of the employed fluids (in this work air and water, conductivity of water is much higher than that of air). Using the difference in the electrical conductivity, the WMS provides the local void fraction. The WMS utilized in this work includes two identical planes of parallel 16×16 grid of wires. The separation distance between these two planes is 32 mm. The WMS was installed in a 76.2 mm (3-inch) diameter vertical pipe to extract information such as void fraction distribution, structure velocity, and slug/churn flow structure. The superficial gas (air) velocity (VSG) ranged from 10 to 38.4 m/s. Liquid (water) superficial velocities (VSL) of 0.30, 0.46, 0.61 and 0.76 m/s were employed. To study the effects of viscosity on the slug/churn flow structure, Carboxyl Methyl Cellulose (CMC) was added to water to increase the liquid viscosity without altering its density. Each experiment was performed for 60 seconds. An operation frequency for the WMS of 10 kHz (totally 600,000 frames per experiment) was used for all experiments.
- Published
- 2014
5. Experimental Study of Vertical Gas-Liquid Pipe Flow for Annular and Liquid Loading Conditions using Dual Wire-Mesh Sensors
- Author
-
Vieira, R. E., Parsi, M., Torres, C. F., Shirazi, S. A., Mclaury, B. S., Schleicher, E., and Hampel, U.
- Subjects
Wire-Mesh Sensor ,two-phase flow ,liquid loading ,void fraction ,flow visualization ,annular flow - Abstract
In gas well production, liquid is produced in two forms, droplets entrained in the gas core and liquid film flowing on the tubing wall. For most of the gas well life cycle, the predominant flow pattern is annular flow. As gas wells mature, the produced gas flow rate reduces decreasing the liquid carrying capability initiating the condition where the liquid film is unstable and flow pattern changes from fully co-current annular flow to partially co-current annular flow. The measurement and visualization of annular flow and liquid loading characteristics is of great importance from a technical point of view for process control or from a theoretical point of view for the improvement and validation of current modeling approaches. In this experimental investigation, a Wire-Mesh technique based on conductance measurements was applied to enhance the understanding of the air-water flow in vertical pipes. The flow test section consisting of a 76 mm ID pipe, 18 m long, was employed to generate annular flow and liquid loading at low pressure conditions. A 16×16 wire configuration sensor is used to determine the void fraction within the cross-section of the pipe. Data sets were collected with a sampling frequency of 10,000 Hz. Physical flow parameters were extracted based on processed raw measured data obtained by the sensors using signal processing. In this work, the principle of Wire-Mesh Sensors and the methodology of flow parameter extraction are described. From the obtained raw data, time series of void fraction, mean local void fraction distribution, characteristic frequencies and structure velocities are determined for different liquid and gas superficial velocities that ranged from 0.005 to 0.1 m/s and from 10 to 40 m/s, respectively. In order to investigate dependence of liquid loading phenomenon on viscosity, three different liquid viscosities were used. Results from the Wire-Mesh Sensors are compared with results obtained from previous experimental work using Quick Closing Valves and existing modeling approaches available in the literature.
- Published
- 2014
Catalog
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.