Search

Porous materials have recently attracted significant attention in the aerospace and biomedical fields for addressing issues related to friction and wear. Porous materials are beneficial in applications where continuous lubrication is not feasible or for components that operate under extreme conditions, such as high speeds, elevated temperatures, and heavy loads. The pores can serve as reservoirs for liquid lubricants, which are gradually released during the operation of the components. The tribological properties of these materials depend on their porosity, the lubricants used, and any additional additives incorporated into the porous materials. This review article provides insight into common fabrication techniques for porous materials and examines their tribological performance for all three classes of materials—polymers, metals, and ceramics. Additionally, it discusses design criteria for porous self-lubricating materials by highlighting the critical properties of both the substrate and lubricants. [ABSTRACT FROM AUTHOR]

In the present work, the effect of graphite nanoplatelets (GNPs) on tribological properties of the aluminum (Al), and Al/alumina (Al2O3) composite are studied. GNPs are multilayer graphene sheets which were used as a solid lubricant material. Two sets of composites, Al/GNPs and Al/GNPs/Al2O3 with varying amounts of reinforcements, were synthesized by powder metallurgy that involves cold compaction followed by hot compaction. The hardness of the composites increased with the addition of GNPs and Al2O3. The Al/GNPs composite with 1 wt.% of GNPs (Al/1GNPs) showed a 20% increase in hardness whereas Al/GNPs/ Al2O3 composite with 1 wt.% GNPs and 2 wt.% Al2O3 (Al/1GNPs/2Al2O3) showed 27% increases in hardness compared to the pure Al. The coefficient of friction measured at 20 N was observed to be 22% and 53% lesser for Al/1GNPs and Al/1GNPs/2Al2O3, respectively, compared to corresponding alloys without graphene Al. The X-ray diffraction and scanning electron microscopy analysis revealed the presence of GNPs at the worn surface after the tribology tests. The wear rate was also reduced significantly. In comparison with pure Al, the Al/1GNPs and Al/1GNPs/2Al2O3 composites resulted in 5- and 20-times lesser wear rate, respectively. The addition of Al2O3 caused reduction in wear rate due to higher hardness and load carrying ability, whereas composites with more than 1 wt.% GNPs showed higher wear rate due to lower hardness and higher porosity. The Al/1GNPs/2Al2O3 composite exhibited the least coefficient of friction (0.2–0.25) and wear rate (1 × 10−6–4 × 10−6 mm3/N.m) compared to other GNPs and Al2O3 reinforced Al composites. The worn surfaces were further analyzed to understand the wear mechanism by Raman spectroscopy, transmission electron microscopy, and x-ray diffraction to detect the Al4C3 phase formation, chemical bonding, and defect formation in graphene. [ABSTRACT FROM AUTHOR]

Wear and friction properties of Al2O3 composite reinforced with in-situ formed aluminum borate (9Al2O3·2B2O3) and hexa-boron nitride (h-BN) have been investigated. The initial constituents for the composites were Al2O3, AlN, and H3BO3. The H3BO3 was used as a source of B2O3, where B2O3 reacted with AlN and Al2O3 to form in-situ h-BN and 9Al2O3·2B2O3. Based on the thermodynamic calculation and phase transformation, four different compositions were selected. First, the powders were mixed by ball milling followed by compaction at 10 MPa. The compacted pellets were sintered at 1400 °C in vacuum. The composites were characterized using X-ray diffraction followed by hardness measurement and reciprocating sliding test against alumina and steel balls. The X-ray diffraction results revealed the formation of in situ phases of 9Al2O3·2B2O3 and h-BN that improved the tribological properties. By comparing the tribological performance of different composites, it was found that the hard 9Al2O3·2B2O3 phase maintains the wear resistance of composites, whereas the coefficient of friction is highly dependent on the counter ball. Against alumina ball, the lowest coefficient of friction was observed for the composites with maximum h-BN concentration and minimum aluminum borate concentration, whereas the opposite trend was observed against the steel ball. [ABSTRACT FROM AUTHOR]