Search

Voltage wave reflection phenomena along power cables are particularly threatening on ac motor drives equipped with silicon carbide power mosfets due to very short switching times and high switching frequency. Overvoltage suppression resistance inductance capacitance (RLC) networks are usually added but leading to extra cost and a lower efficiency. A completely different overvoltage mitigation approach is presented in this paper exploiting an open-end winding motor configuration. Overvoltage occurring on the terminals of motor phase windings are, in fact, mitigated by simply coordinating the operations of the two inverters; thus, no passive RLC networks are required. The proposed approach is intended as a mean to provide a further valuable feature to open-winding systems at no extra cost, but it can be also valued as an alternative to conventional bridge inverters equipped with overvoltage mitigation devices. [ABSTRACT FROM AUTHOR]

A low input current total harmonic distortion (THD) rectifier is presented, tailored around an open-end winding permanent magnet synchronous generator. Specifically, a six-level converter topology is obtained by connecting the generator stator winding to a three level T-type unidirectional rectifier on one side, and to an auxiliary two-level inverter on the other side. The T-type rectifier manages the entire active power stream and operates at the line frequency in order to minimize the switching power losses. The auxiliary inverter is instead driven by a standard PWM technique, being tasked to sinusoidally shape the input current and to actively balance the voltage across the dc-bus capacitors of the T-type rectifier. Such an inverter, being rated at a lower power and at a lower voltage than the T-type rectifier, can exploit low-cost power mosfets. The proposed topology, featuring a very low input current THD, could well supplement in aircraft, portable or distributed generation applications, modern high-speed permanent magnet synchronous generators featuring a quite small stator impedance. Simulation and experimental results confirm the effectiveness of the proposed configuration. [ABSTRACT FROM AUTHOR]

An optimal current control strategy for asymmetrical hybrid multilevel inverters (MLIs) is proposed in this paper enabling their use on motor drives, static synchronous compensators, and photovoltaic and wind generators, where a fast and precise current regulation is required. A key feature of these highly efficient converters is that an ac machine (motor or transformer) operates according to an open-end winding configuration, connected on one side to a main MLI and, on the other side, to an auxiliary two-level inverter (TLI). The first efficiently controls the main power stream operating at a low switching frequency, while the TLI acts as an active power filter, exploiting a conventional high-frequency two-level pulsewidth modulation (PWM) technique. The proposed control scheme optimally exploits the key features of the two inverters by suitably sharing the control task. In fact, a predictive current control is assigned to the MLI, which can be accomplished by low switching frequency operations, while the high switching frequency of the PWM-operated TLI is exploited to accomplish a fast and precise closed-loop current control, processing only a part of the power stream flowing through the system, thus producing low power losses. Simulations and experimental results confirm the consistency of the proposed approach. [ABSTRACT FROM AUTHOR]

An open-end winding machine configuration and a suitable control strategy for medium-voltage ac motor drives applications are proposed in this paper in order to reduce the distortion of phase voltages in multilevel inverters (MLIs). Differently than standard open-end winding configurations, where two inverters provide active power to both sides of the stator winding, a main MLI supplies in this case the machine on one side, while an auxiliary two-level inverter acts as active power filter on the other side. A high efficiency step modulation manages the MLI, while the auxiliary unit is pulse width modulation (PWM) operated. As the phase current harmonic content is improved, the torque ripple is reduced and the drive efficiency is increased. By exploiting the proposed approach, the apparent switching frequency of the system is that typical of a PWM inverter, although the main unit is operated according to a voltage step modulation strategy. Simulation and experimental results confirm the consistency of the proposed methodology. [ABSTRACT FROM PUBLISHER]

Due to their inner structural redundancy, ac multidrive systems (MDSs) can achieve a fault-tolerance capability with minor circuit modifications. However, some additional components are generally required in order to create emergency current paths. According to a recently presented approach, the amount of additional components can be reduced by exploiting healthy drives to support faulty drives. This can be obtained by connecting together the neutral points of motor stator windings and suitably sharing the neutral current of faulty units among some, or all, healthy units. Following such an approach, three current-sharing methodologies for fault-tolerant MDSs are presented in this paper, which are able to cope with single or multiple failures. They are first theoretically introduced and then validated by mean of simulations and experimental test results. [ABSTRACT FROM PUBLISHER]

This paper deals with the analysis and implementation of a new scalar control technique for industrial interior permanent-magnet synchronous motor drives that exploits energy-saving capability. In particular, the proposed control strategy forces the conditions of maximum torque per ampere (MTPA), flux weakening (FW), and maximum torque per voltage (MTPV) simply by assigning polynomial relationships between the operating angles of the machine. Although the dynamic performance of the drive is worsened compared to that of vector control schemes, the modified scalar control allows us to work in energetic conditions, very close to those obtained with vector-controlled drives exploiting MTPA, FW, and MTPV strategies. The control techniques are implemented without using any speed and voltage measurement and with only a single current feedback. This paper provides a detailed study of the control strategy, showing the effectiveness and limitations of the method through simulations and experimental results. [ABSTRACT FROM PUBLISHER]

This paper deals with a novel hybrid transformer configuration for MV/LV three-phase distribution systems. The configuration involves a standard distribution transformer with an open-end secondary winding, which is connected to the LV grid and a four-legged inverter with a floating DC bus. Unlike previous hybrid transformers, the proposed configuration eliminates the need for a bidirectional converter and auxiliary transformer windings as well. The fourth leg of the inverter is exploited to manage the neutral line current. The main advantage of the proposed configuration is its ability to provide phase voltage control at the distribution grid edge. This enables the compensation of various grid voltage anomalies such as sags, swells and some kinds of interruptions. The effectiveness of the proposed configuration is demonstrated through simulation and experimental results, highlighting its promising performance in real-world scenarios. [ABSTRACT FROM AUTHOR]