Search

This article systematically compares two axial flux permanent magnet machines designed for a university student racing car application: a double-rotor single-stator yokeless and segmented armature (YASA) structure, and a single-stator single-rotor configuration. Both machines are optimized for minimum loss and active weight using three-dimensional finite element analysis and the highest performing candidate designs are compared in more detail. The studies indicate that the benefits offered by the YASA configuration over the single-stator single-rotor machine are achieved only for specific designs that are heavier. For the design space with lower mass, albeit with increased losses, the Pareto front designs overlap. In this envelope, the YASA configuration demonstrates higher efficiencies at higher speeds, whilst the single-stator single-rotor is more efficient in high torque duty cycles. This shows the performance of the two machines is very similar and the choice is application specific. To validate the finite element analysis used in the optimization, a prototype was built and tested. Results showed good alignment between simulation and experimental data. [ABSTRACT FROM AUTHOR]

Outer-rotor switched reluctance machines (SRMs) have drawn much attention as promising candidates for in-wheel direct-drive motors of future electric vehicles. This article presents a systematic performance comparison of three outer-rotor SRM topologies for in-wheel traction applications in terms of the specific torque, electromagnetic efficiency, torque ripple, radial force, and mechanical aspects. A generalized design optimization framework for SRMs is proposed to enable the fast evaluation of large numbers of designs generated from the differential evolution by incorporating an analytical current profile estimation into the transient finite element analysis. The relationship between the saliency ratio and converter volt-ampere rating is also discussed. The calculations are then benchmarked with the experimental results from an existing prototype. The effectiveness of the performance prediction method and the proposed optimization approach is validated. [ABSTRACT FROM AUTHOR]

Axial-flux permanent-magnet machines are used particularly in applications requiring a compact structure. Their disc-shaped topology and axial airgap have led to a variety of configurations including two popular ones: the yokeless and segmented armature (YASA), and the single-stator single-rotor or single-sided machine. In this study, a comprehensive comparative analysis of these configurations is conducted at different magnetic and electric loadings. It is found that at lower loadings, typically employed for air-cooled machines, the torque/ampere characteristics of the YASA machine are almost identical to those of a single-sided machine constructed with half the magnet volume. On the other hand, the single-sided machine outperforms the YASA machine when the magnet volumes in both machines are maintained equal. However, for higher electric loadings, the torque/ampere characteristics of the YASA machine droop significantly less than those of the single-sided machine. This article includes analytical estimations, which are verified with experimentally validated finite element analysis (FEA) simulations. In addition, the impacts of the armature reaction on saturation and the magnetic flux linkage, the magnet losses, and eddy current losses in both machines are also explored. [ABSTRACT FROM AUTHOR]

Optimizing the design of electric machines is a vital step in ensuring the economical use of active materials. The three-dimensional (3-D) flux paths in axial flux permanent magnet (AFPM) machines necessitate the use of computationally expensive 3-D electromagnetic analysis. Furthermore, a large number of design evaluations is required to find the optimum, causing the total computation time to be excessively long. In view of this, a two-level surrogate assisted algorithm capable of handling such expensive optimization problems is introduced, which substantially reduces the number of finite element analysis (FEA) evaluations to less than 200 while conventional algorithms require thousands of designs to be analyzed. The proposed algorithm is employed to optimally design an AFPM machine within a specified envelope, and to identify the limits of cost and efficiency. In order to obtain these limits, the variables' ranges are assigned to be as wide as possible, resulting in a vast design space, the study of which was enabled by the developed special algorithm. Additionally, optimized designs with different rotor polarities are systematically compared in order to form the basis for a set of generalized design rules. [ABSTRACT FROM AUTHOR]

Equivalent circuit parameters serve as the basis for performance estimation and implementation of power electronic drives controls and therefore their accurate evaluation is very important. Specified in the newly approved IEEE Std 1812, a short-circuit test can be employed, in combination with an open-circuit measurement, in order to determine the back emf and the synchronous inductance. In the case of interior permanent magnet (IPM) machines, this approach can be used only to determine the d-axis inductance and additional and separate measurements are required for the q-axis inductance. In this respect, various methods, inclusive of dc step response tests, on-load tests, and a widely used test in industry, which involves locked-rotor measurements at variable voltage and constant frequency supply, are studied in detail, based on two-dimensional finite element analysis. Locked-rotor methods based on dc current supply and static torque versus rotor position measurements are introduced for determining the q-axis inductance in combination with the standardized open-circuit and short-circuit tests. A critical study of the inductances determined from different tests is conducted, and experimental results on an IPM motor design with non-sinusoidal back emf, relatively high torque ripple, and low leakage are presented. [ABSTRACT FROM AUTHOR]

Switched reluctance (SR) machines are attractive because they present relatively high efficiency and torque density in spite of lacking permanent magnets. This paper focuses on a two-objective optimization of an external rotor SR motor with a stator that has concentrated coils and a rotor with magnetically isolated modules. The objectives are minimum loss and mass, and 11 independent dimensionless geometric variables are considered as inputs that affect them. A combined design of experiments (DOE) and differential evolution (DE) approach is proposed. The DOE methodology is used to reduce the search space by eliminating from consideration input variable values, leading to poor-performing designs. Following this initial DOE study, an optimization study based on DE is run over the reduced search space, which leads to significant savings in computation time. Furthermore, a directed graph-based method for comparing different designs on the Pareto front to rank the best compromise designs is proposed. [ABSTRACT FROM AUTHOR]

Coreless axial flux machines are of interest because of the absence of stator core losses and cogging torque. These machines generally employ concentrated windings. One of the challenges with such a winding is that the torque producing MMF component that corresponds to the fundamental of the magnet excitation is accompanied by substantial asynchronous components. These harmonics cause losses in the rotor core and magnets, which can become significant at high speeds. This paper proposes a new multilayer winding arrangement to eliminate the non-torque producing MMF components. This winding is applied to a 12-coil 16-pole coreless axial flux machine. The efficacy of the winding is established by 3-D finite-element analysis. [ABSTRACT FROM AUTHOR]

Coreless axial flux permanent magnet (AFPM) machines are attracting increasing attention due to their compact structure and high torque density. The torque to weight ratio can be further enhanced by the use of alternate conductor materials, such as carbon nanotube (CNT), or aluminum windings in place of the copper material coils. This paper proposes a coreless AFPM synchronous motor with CNT windings. Analytical equations are developed to allow a systematic comparison of machine designs with different conductor materials. The performance of machine designs with different coil materials, namely, copper, aluminum, and CNT, is evaluated and compared. The calculations are also backed by 3-D finite-element analysis. [ABSTRACT FROM AUTHOR]

A novel automated design optimization procedure based on the application of an ultrafast computationally efficient finite-element analysis (CE-FEA) for current-regulated synchronous reluctance machines supplied from power electronic converters is proposed. The CE-FEA uses only a minimum number of magnetostatic solutions in order to comprehensively evaluate performance, including ripple torque and core losses. The optimization algorithm is based on differential evolution, and uses as independent variables the torque angle and ratios for a generic rotor topology with four flux barriers. Two problems, one with two and the other with three objectives, are studied and results are compared. Global performance indices and objectives incorporate the effect of average torque output, losses, torque ripple, and power factor at fixed cost. It is shown that through optimal studies with more than 5000 candidate designs, high output power, high efficiency, and low torque ripple can be achieved, while the relatively low power factor remains an inherent limitation of synchronous reluctance technology. Simulations are validated versus tests from a 10-hp 1800-r/min prototype. [ABSTRACT FROM AUTHOR]

A motor for in-wheel electric vehicle (EV) requires high efficiency and specific torque. In view of this, permanent-magnet brushless dc (PM BLDC) motor is most commonly employed for this application. However, due to the increasing cost of PMs, machines that do not use PMs are attracting interest. Switched reluctance motor (SRM), with its simple and robust construction, along with fault tolerant operation, is a viable option for in-wheel EV application. However, the SRM has low specific torque as compared with BLDC. Therefore, design improvements are required to make SRM a viable alternative to BLDC motor. In this paper, a new 12/26 pole SRM with high specific torque is proposed for in-wheel EV application. This machine has segmented-rotor-type construction. Also, concentrated-winding arrangement is used, ensuring low end-winding volume and copper loss. The developed machine also has high efficiency. In order to verify the design, the prototype of the machine is fabricated, and experimental results are presented. [ABSTRACT FROM AUTHOR]