Search

This paper proposes a method to boost the terminal voltages using a capacitive network. The boosted voltage can improve the power capability of an interior permanent magnet synchronous motor (IPMSM). In the conventional drive system fed by a voltage-source inverter, the terminal voltages of the motor are limited by the dc-link voltage. Such a voltage limitation reduces the torque capability at high speeds. Thereby, the maximum output power is limited. To overcome this feature, series capacitor network between the inverter and the motor is introduced in the proposed IPMSM drive system. The series capacitors boost the motor terminal voltages higher than the inverter voltages to increase the rated speed, resulting in improved power capability. The rated speed in the proposed drive system can be redefined to the desired value through a capacitive network. The enhanced power capability and design freedom in the rated speed are particularly advantageous in fan-load applications where the load torque is proportional to the square of speed. This article presents the structure, d–q equivalent model, operating characteristics, and operable area of the proposed drive. Experimental results are given to verify the feasibility and effectiveness of the proposed system. [ABSTRACT FROM AUTHOR]

This article proposes a method to extend the operating area of the surface permanent magnet motor by inserting the passive power networks between the motor and the voltage source inverter (VSI). In the conventional motor drive system, since the operating area is limited by the maximum voltage, which is synthesized by the inverter, the output torque capability is reduced in the high-speed region. In order to extend the operating area, two types of passive power networks are proposed in this article. The power networks supply the reactive power to the motor for amplifying the motor terminal voltage. Due to the actions, the proposed motor drive system can utilize a higher maximum motor terminal voltage than that in the conventional drive systems. Depending on the network types, the operating point at which the maximum power or torque is generated is shifted to a high speed. The design, control, and analysis methods of the proposed system are presented in this article. The effectiveness of the proposed system is verified through the experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a fault-tolerant operation for dual three-phase surface-mounted permanent magnet machines (SPMSMs) that were both electrically connected on three winding phases and mechanically connected on one shaft. The open-phase fault-tolerant operation is considered in dual three-phase SPMSMs drive thus combining motor drive of three-phase and single-phase. The proposed method controls the torque of each motor with different phases using a single inverter. In order to control these motors, the torque and current are distributed between the motors with the specific ratio. Methods for minimizing torque ripple and copper losses and maximizing the output torque of the three-phase motor are stated in this paper. Accordingly, a system with cost-effective and enhanced reliability is proposed without any configuration adjustment or auxiliary switching devices. The mathematical analysis and experiments are presented to verify the feasibility of the proposed method. After the fault, the resulting system is able to provide up to 75% of the rated torque, and up to 50% of the torque can be utilized without any torque ripple. [ABSTRACT FROM AUTHOR]

A double inverter fed wound machine (DFWM) needs two inverters on the rotor as well as the stator side. This scheme gives more freedom to operation of an electric machine and improves the output power capability and the efficiency, but its control method becomes more complex because the number of control variables and the operating constraints increase. This paper deals with a control method of DFWM for minimizing the copper loss in maximized operating area. The possible operation area considering all constraints of currents, voltages, and flux is analyzed on the stator currents plane to maximize the operating area. For the minimum copper loss operation in the operating area, different modes are defined and the optimal currents are determined in each mode. Also, the optimal current selection algorithm is proposed to achieve the torque control using the optimal currents. The simulation and experimental results about wound machines are presented to show the feasibility of the proposed control method. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel drive method for interior permanent magnet machines (IPMMs). In the proposed system, a two-phase IPMM is fed from a single-phase H-bridge inverter for low-cost applications. Its main winding in d -axis is connected to the inverter and the auxiliary winding in q-axis is inherently short circuited. This configuration enables the motor to operate in a wider speed range with higher energy efficiency than most other single-phase drive systems. Also, its torque capability in the high-speed range is as high as that of the three-phase IPMM drive despite the reduced power devices, drivers, and current sensors. Accordingly, the proposed system has benefits such as simple structure, low cost, high-power density, and improved efficiency. In this paper, the system is modeled with an equivalent three-phase machine. Based on the model, its torque characteristics and operating areas are analyzed and compared to those of the conventional IPMM drives. A speed control algorithm is also developed. It includes a maximum torque per ampere control to improve drive efficiency and a flux-weakening control to maximize the feasible inverter output voltage. The proposed system and control algorithm are verified by experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes the novel control method for a monoinverter dual parallel (MIDP) drive system with interior permanent magnet synchronous machines (IPMSMs). It includes maximum torque per ampere (MTPA) control to elevate drive efficiency and active damping control to alleviate inherent stability problem of an MIDP motor drive system. Due to the combination of reluctance and electromagnetic torques, the d- and q-axis currents of IPMSM are coupled unlike those of induction and surface-mounted permanent magnet machines. For this reason, MTPA and active damping control of a MIDP IPMSM drive system are far more complex than those with nonsalient motors. In this paper, model-based mathematical analysis about MTPA and active damping control for MIDP IPMSM drive system are provided. Experimental results with two 1.6-kW IPMSMs are presented to verify the proposed algorithm. [ABSTRACT FROM AUTHOR]

This paper presents the control method for mono inverter dual parallel (MIDP) surface-mounted permanent-magnet synchronous motor (SPMSM) drive system. Unlike the MIDP induction machine drive system, MIDP SPMSM drive system suffers from the inherent instability due to the lack of slip. The proposed active damping control method refrains the system oscillation coming from the mechanical and electrical unbalances and enables the stable operation. This paper also presents the simple maximum torque per ampere control method for MIDP SPMSM drive system. Mathematically calculated optimal currents reduce the amplitude of the currents and improve the drive efficiency. To maximize the merits of the MIDP motor drive system, a sensorless algorithm is also applied. Experiments with the 600-W SPMSMs are executed to verify the feasibility of the proposed control method. [ABSTRACT FROM PUBLISHER]

This paper proposes a single-phase grid-connected wound rotor machine that has the single-phase stator and three-phase rotor windings. The machine has no auxiliary winding or capacitor unlike conventional single-phase machines. Nevertheless, it can operate in all four quadrants of the torque–speed plane with a three-phase inverter. For adjustable speed drives, an isolated three-phase inverter is applied to the rotor windings while the stator winding is directly connected to a single-phase source. The grid filter and rectifier of the conventional system are eliminated and the rotor-side slip rings can be also removed by the inverter integration. So the overall structure of the proposed drive system is simple and cost effective. In this paper, the proposed machine is modeled into a modified d–q model considering the absence of q-axis stator coil. Its characteristics are analyzed and vector control methods of the grid power factor, dc-link voltage, and speed are proposed. For more efficient control, the optimal rotor current set is calculated from the minimum copper loss condition. The system has wider operating areas than other single-phase drive systems. The feasibility of the proposed system is verified by experiments. [ABSTRACT FROM AUTHOR]