Search

New developments in mobile resistivity meter instrumentation have made it possible to survey large areas with dense data coverage. The mobile system usually has a limited number of electrodes attached to a cable that is pulled along behind an operator so that a large area can be covered within a short time. Such surveys can produce three‐dimensional datasets with hundreds of thousands of electrodes positions and data points. Similarly, the inverse model used to interpret the data can have several hundred thousand cells. It is impractical to model such large datasets within a reasonable time on microcomputers used by many small companies employing standard inversion techniques. We describe a model segmentation technique that subdivides the finite‐element mesh used to calculate the apparent resistivity and Jacobian matrix values into a number of smaller meshes. A fast technique that optimizes the calculation of the Jacobian matrix values for multi‐channel systems was also developed. A one‐dimensional wavelet transform method was then used to compress the storage of the Jacobian matrix, in turn reducing the computer time and memory required to solve the least‐squares optimization equation to determine the inverse model resistivity values. The new techniques reduce the calculation time and memory required by more than 80% while producing models that differ by less than 1% from that obtained using the standard inversion technique with a single mesh. We present results using a synthetic model and a field dataset that illustrates the effectiveness of the proposed techniques. [ABSTRACT FROM AUTHOR]

ABSTRACT The use of optimized arrays generated using the 'Compare R' method for cross-borehole resistivity measurements is examined in this paper. We compare the performances of two array optimization algorithms, one that maximizes the model resolution and another that minimizes the point spread value. Although both algorithms give similar results, the model resolution maximization algorithm is several times faster. A study of the point spread function plots for a cross-borehole survey shows that the model resolution within the central zone surrounded by the borehole electrodes is much higher than near the bottom end of the boreholes. Tests with synthetic and experimental data show that the optimized arrays generated by the 'Compare R' method have significantly better resolution than a 'standard' measurement sequence used in previous surveys. The resolution of the optimized arrays is less if arrays with both current (or both potential) electrodes in the same borehole are excluded. However, they are still better than the 'standard' arrays. [ABSTRACT FROM AUTHOR]

Abstract: There have been major improvements in instrumentation, field survey design and data inversion techniques for the geoelectrical method over the past 25years. Multi-electrode and multi-channel systems have made it possible to conduct large 2-D, 3-D and even 4-D surveys efficiently to resolve complex geological structures that were not possible with traditional 1-D surveys. Continued developments in computer technology, as well as fast data inversion techniques and software, have made it possible to carry out the interpretation on commonly available microcomputers. Multi-dimensional geoelectrical surveys are now widely used in environmental, engineering, hydrological and mining applications. 3-D surveys play an increasingly important role in very complex areas where 2-D models suffer from artifacts due to off-line structures. Large areas on land and water can be surveyed rapidly with computerized dynamic towed resistivity acquisition systems. The use of existing metallic wells as long electrodes has improved the detection of targets in areas where they are masked by subsurface infrastructure. A number of PC controlled monitoring systems are also available to measure and detect temporal changes in the subsurface. There have been significant advancements in techniques to automatically generate optimized electrodes array configurations that have better resolution and depth of investigation than traditional arrays. Other areas of active development include the translation of electrical values into geological parameters such as clay and moisture content, new types of sensors, estimation of fluid or ground movement from time-lapse images and joint inversion techniques. In this paper, we investigate the recent developments in geoelectrical imaging and provide a brief look into the future of where the science may be heading. [Copyright &y& Elsevier]

Electrical impedance tomography (EIT) was used to monitor the movement of a fluorinated hydrocarbon dense nonaqueous phase liquid (DNAPL) through a saturated porous medium within a laboratory column. Impedance measurements were made using a horizontal plane of 12 electrodes positioned at regular intervals around the centre of the column. A 2D inversion algorithm, which incorporated the cylindrical geometry of the column, was used to reconstruct resistivity and phase images from the measured data. Differential time-lapse images of DNAPL movement past the plane of electrodes were generated by the cell-by-cell subtraction of resistivity and phase baseline models from those associated with the DNAPL release stage of the experiment.The DNAPL pulse was clearly delineated as resistive anomalies in the differential time-lapse resistivity images. The spatial extent of the resistive anomalies indicated that in addition to vertical migration, some lateral spreading of the DNAPL had occurred. Residual contamination could be detected after quasi-static conditions were reestablished. Residual DNAPL saturation was estimated from the resistivity model data by applying Archie''s second equation.Despite significant measured phase changes due to DNAPL contamination, the differential phase images revealed only weak anomalies associated with DNAPL flow; these anomalies could be seen only in the initial stages of the experiment during peak flow through the plane of electrodes. [Copyright &y& Elsevier]

Electrical resistivity tomography (ERT) surveys are widely used in geological, environmental and engineering studies. However, the effectiveness of surface ERT surveys is limited by decreasing resolution with depth and near the ends of the survey line. Increasing the array length will increase depth of investigation, but may not be possible at urban sites where access is limited. One novel method of addressing these limitations while maintaining lateral coverage is to install an array of deep electrodes. Referred to here as the Multi-Electrode Resistivity Implant Technique (MERIT), self-driving pointed electrodes are implanted at depth below each surface electrode in an array, using direct-push technology. Optimal sequences of readings have been identified with the “Compare R” method of Wilkinson. Numerical, laboratory, and field case studies are applied to examine the effectiveness of the MERIT method, particularly for use in covered karst terrain. In the field case studies, resistivity images are compared against subsurface structure defined from borings, GPR surveys, and knowledge of prior land use. In karst terrain where limestone has a clay overburden, traditional surface resistivity methods suffer from lack of current penetration through the shallow clay layer. In these settings, the MERIT method is found to improve resolution of features between the surface and buried array, as well as increasing depth of penetration and enhancing imaging capabilities at the array ends. The method functions similar to a cross-borehole array between horizontal boreholes, and suffers from limitations common to borehole arrays. Inversion artifacts are common at depths close to the buried array, and because some readings involve high geometric factors, inversions are more susceptible to noise than traditional surface arrays. Results are improved by using errors from reciprocal measurements to weight the data during the inversion. [ABSTRACT FROM AUTHOR]

Abstract: We describe the use of a fully volumetric geophysical imaging approach, three-dimensional electrical resistivity (3D ERT), for bedrock detection below mixed sand and gravel deposits typical of fluvial valley-fill terraces. We illustrate the method through an analysis of terrace deposits of the Great Ouse River (UK), where up to 4m of sand and gravel have filled the valley bottom during the latest Pleistocene. We use an edge detector to identify the steepest gradient in first-derivative resistivity profiles, which yields an estimate of bedrock depth (verified by drilling) to a precision better than 0.2m (average) and 0.4m (standard deviation). Comparison of a range of drilling techniques at the site has revealed that borehole derived interface depths suffered from levels of uncertainty similar to those associated with the 3D ERT — indicating that the reliability of bedrock interface depths determined using these two approaches is comparable in this case. The 3D ERT method provides a high spatial resolution that enabled a previously unknown erosional bedrock structure, associated with the change from deeper first terrace to second terrace deposits, to be identified in the Great Ouse valley. The method provides a relatively quick method to quantify terrace fill volume over large sites to a greater degree of precision than currently available. [Copyright &y& Elsevier]

Abstract: Robust characterization and monitoring of dense nonaqueous phase liquid (DNAPL) source zones is essential for designing effective remediation strategies, and for assessing the efficacy of treatment. In this study high-resolution cross-hole electrical resistivity tomography (ERT) was evaluated as a means of monitoring a field-scale in-situ bioremediation experiment, in which emulsified vegetable oil (EVO) electron donor was injected into a trichloroethene source zone. Baseline ERT scans delineated the geometry of the interface between the contaminated alluvial aquifer and the underlying mudstone bedrock, and also the extent of drilling-induced physical heterogeneity. Time-lapse ERT images revealed major preferential flow pathways in the source and plume zones, which were corroborated by multiple lines of evidence, including geochemical monitoring and hydraulic testing using high density multilevel sampler arrays within the geophysical imaging planes. These pathways were shown to control the spatial distribution of the injected EVO, and a bicarbonate buffer introduced into the cell for pH control. Resistivity signatures were observed within the preferential flow pathways that were consistent with elevated chloride levels, providing tentative evidence from ERT of the biodegradation of chlorinated solvents. [ABSTRACT FROM AUTHOR]