Search

The human body constantly produces thermal electromagnetic radiation with a maximum of about 10 μm. This thermal radiation has a number of positive effects on the human body and, in addition, allows the insulation under clothing to be improved under extreme climatic conditions, causing a significant reduction in ambient temperature. With so-called far-infrared (FIR) textiles, it is possible to ensure the reflection of thermal radiation back to the human body. In the first part of this review, the generation of heat by the human body and its propagation by radiation through the skin are comprehensively explained. The thermal characteristics of the individual skin layers as an emitter of infrared radiation are given. The second part discusses the basic preparation methods of FIR textiles. Suitable particle systems are described based on metals and their oxides, porous carbon, and special ceramics. Modification of the fiber phase (especially the fineness of the fibers and the porosity of the fabric) in combination with the surface coating of metals is also used for their health-promoting effects. The main manufacturers of FIR textiles and their typical products are mentioned.

The air flow and conjugate heat transfer through the fabric was investigated numerically. The objective of this paper is to study the thermal insulation of fabrics under heat convection or the heat loss of human body under different conditions (fabric structure and contact conditions between the human skin and the fabric). The numerical simulations were performed in laminar flow regime at constant skin temperature (310 K) and constant air flow temperature (273 K) at a speed of 5 m/s. Some important parameters such as heat flux through the fabrics, heat transfer coefficient, and Nusselt number were evaluated. The results showed that the heat loss from human body (the heat transfer coefficient) was smallest or the thermal insulation of fabric was highest when the fabric had no pores and no contact with the human skin, the heat loss from human body (the heat transfer coefficient) was highest when the fabric had pores and the air flow penetrated through the fabric.

This paper analyzes the relationship between technological parameters of spinning of 100% CV Vortex yarns of different counts and its selected geometrical parameters (a lead of helix of wrapping fibre ribbon, yarn diameter) as well as yarn properties. The number of twist of wrapping fibre layer is determined. The effect of the yarn delivery speed, hollow spindle diameter, and the main draft on the hairiness, mass irregularity, tenacity, elongation, resistance to abrasion and bending rigidity of Vortex yarn is observed. The yarn properties are compared with the properties of open-end rotor spun yarns. Slivers of the same spinning lot were used for the production of both kinds of yarn. The results showed that the delivery speed in combination with spindle diameter affects yarn diameter, hairiness and abrasion resistance. Mass irregularity and imperfections of yarn is mainly affected by the main draft of drafting unit. Technological parameters of spinning do not affect the level of bending rigidity of the Vortex yarn. Tested rotor spun yarns had a larger diameter, higher hairiness, lower tenacity and higher elongation, lower mass irregularity and number of imperfections, higher abrasion resistance and lower bending rigidity compared to tested Vortex spun yarns.

Flex fatigue behaviour of plastic optical fibres (POFs) with the diameters of 0.2 and 0.3 mm under different pretensions is measured with fatigue life curve by flexometer. The fatigue sensitivity coefficient is calculated by the linear fitting curve of normalised stress versus logarithm of bending cycles. The residual modulus is investigated during the flex fatigue processes. The results exhibit the exponential relationship between applied pretension and numbers of bending cycles at break. It is indicated that the flex fatigue of POFs might be sensitive with high swing angle or swing speed. There is an evident loss of modulus for two POFs with pretensions of 4 and 10% of ultimate tensile strength during 10-times bending cycles. The values of residual modulus of two POFs almost keep constant after 10-times bending cycles.

CO2 laser treatment can increase the surface roughness of plastic optical fibres (POFs) with the diameter of 0.5 mm and enhance the input intensity and attenuation coefficient accordingly, which is supposed to weaken the side emission of POFs in long distance above 375 mm. TiO2 particles were applied to improve the increasing optical loss of POFs by laser treatment. POFs were first modified with fine TiO2 particles and then treated by CO2 laser with the pixel time from 30 to 120 ìs. The surface morphology was observed by scanning electron microscopy to investigate the changes of micro-structure before and after laser treatment and the distribution of TiO2 particles. The illumination intensity and attenuation coefficient were calculated and compared in two methods. It is visible that the evaluation by model LLF2 with two parts is more suitable for the fitting of experimental data and shows higher input intensity and lower attenuation than that by standard power function. Both the evaluation methods exhibit that the utilization of TiO2 particles could play an active role in the enhancement of side emission of POFs treated by CO2 laser.

Air permeability is one of the most important properties of non-woven fabrics in many applications. This paper aims to investigate the effects of thickness, porosity and density on the air permeability of needle-punched non-woven fabrics and compare the experimental values with two models which are based on hydraulic radius theory and drag theory, respectively. The air permeability of the samples was measured by an air permeability tester FX3300. The results showed that the air permeability of non-woven fabrics decreased with the increase in thickness and density of samples, increased with the increase of porosity, and the air permeability was not directly proportional to the pressure gradient. Meanwhile, the prediction model based on hydraulic radius theory had a better agreement with experimental values than the model based on drag theory, but the values were much higher than the experimental results, especially for higher porosity and higher pressure gradient.

Effective thermal conductivity (ETC) is a very important index for evaluating the thermal property of heterogeneous materials, which include more than two different kinds of materials. Several analytical models were proposed for predicting the ETC of heterogeneous materials, but in some cases, these models cannot provide very accurate predictions. In this work, several analytical models and numerical simulations were studied in order to investigate the differences among them. In addition, some factors which would influence the ETC of heterogeneous materials were investigated by numerical simulation. The results demonstrated that the numerical simulation can provide very accurate prediction, indicated that different analytical models should be selected to predict specific problems based on their assumptions, and suggested that more variables need to be considered in order to improve these analytical models, such as inclusion shape, inclusion size, distribution of inclusions and contact area. Besides, numerical method could be an effective and reliable way to obtain the ETC of heterogeneous materials with any kind of complicated structures.