Search

In this article, a highly efficient battery-balancing circuit with output voltage regulation for mobile applications is proposed and analyzed. The proposed circuit performs a cell-balancing operation for series-connected multiple-battery cells and voltage regulation operation simultaneously without additional power conversion stages. Therefore, it can be integrated into a battery pack with maximized power density and efficiency. These features are essential for recent low-power applications with multiple batteries, such as wireless/smart speakers, drones, and electronic point-of-sale, that require high power density. The operational principle, electrical modeling, and tradeoff relationship between the system power losses and balancing characteristics are derived, and the optimal design candidates of the proposed topology are discussed in terms of Pareto optimization. The effectiveness of the proposed system is verified with a prototype board using GaN switches, and 96.05% efficiency is achieved with a 1.8 V, 0.5 A load. [ABSTRACT FROM AUTHOR]

This paper proposes a resonant switching cell model to analyze and design the single-ended resonant dc–dc converters. The single-ended zero-voltage switching (ZVS) converters such as the Class E converter are efficient for megahertz switching because they feature low turn-on and turn-off switching losses. Also, they use only a ground-referenced switch, allowing a simple gate drive circuit. In this paper, we investigate the single-ended resonant converter with the small input inductance, whereas the conventional Class E converter has a large input inductance. The main contribution of this paper is to propose the resonant switching cell as an analytic model that simplifies the analysis and the design of the resonant dc–dc converters. Furthermore, this paper presents the design method of the resonant switching cell model for minimizing the resonant current magnitude and conduction loss while the converter maintains ZVS property. The experimental results from a 10-MHz GaN-based prototype demonstrate the feasibility and effectiveness of the analysis and design based on the proposed resonant switching cell model. [ABSTRACT FROM AUTHOR]

This paper proposes data transmission method between primary and secondary of the flyback converter without additional communication circuit while simultaneously transferring power. In some application such as a battery charger, the data exchanges between the primary and secondary sides are necessary. In the conventional system, an additional line or wireless communication modules is used for data exchanges, thereby increasing the system and connector size. The proposed system, in comparison, does not use additional signal transceiver but instead exchanges data by simply alternating operation mode of the flyback converter, thus adding communication function while not increasing the volume of the terminal and overall system. The waveform of transformer voltage is used to count the number of resonant pulses, which is used for decoding and encoding the data packet. Bidirectional communication between primary and secondary sides is possible while power is transferred to the output using an appropriate communication protocol. This paper proposes data transmission method for both single output and the multioutput cases. Also, both half-duplex and full-duplex communication using the proposed method is explained. The experimental results are presented to verify the performance of the proposed communication method. [ABSTRACT FROM AUTHOR]

The six-step operation of surface-mounted permanent magnet machine drives in a flux weakening region has many advantages compared to the pulse width modulation mode, such as the reduced switching loss and fully utilized inverter output voltage. However, if the ratio of the sampling frequency to the fundamental frequency is low in fixed sampling system, the low-frequency oscillation in the current can be incurred in the six-step operation. The low-frequency current causes a system stability problem and reduces system efficiency due to an excessive heat and high power loss. Therefore, this paper proposes the variable time step controller for six-step operation. By updating an output voltage, sampling phase currents, and executing the digital controller synchronized with the variable sampling time, the turn on and off switch signals for six-step operation can be generated at the exact moment. As a result, the low-frequency oscillation in the phase current can be eliminated. In addition, the system transfer function of the proposed control method is discussed for the system stability and system dynamic analysis. The effectiveness of the proposed method is verified by the comparative simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a single-switch isolated dc–dc converter suited for a very high-frequency switching operation, especially above 10 MHz. The converter features a small number of passive components, low-switching loss, and low-voltage stress on the switch. In order to achieve low-voltage stress while maintaining zero voltage switching, the voltage waveform across the switch is shaped by designing the resonant network of the converter. The resonant network includes main parasitic components, such as leakage inductances of the transformer and the junction capacitance of the switch. Furthermore, some resonant elements are entirely replaced by these parasitic components under the specific condition. This paper derives the conditions and then minimizes the number of passive components. To validate the design procedure and the performance of the proposed converter, a GaN-based prototype was implemented. It operates at 10 MHz and provides the output power of 10 W from the dc input voltage of 50 V. The output voltage is regulated to 20 V by the ON–OFF control. Experimental results show that the peak voltage on the switch is reduced to 2.2–2.3 times the dc-input voltage and the efficiency of 69% is achieved under the full load. [ABSTRACT FROM AUTHOR]

This paper presents a novel family of single-switch resonant dc–dc converters with low switch voltage stress. The single-switch resonant converter which has a ground-referenced switch is advantageous for implementing the gate drive circuit and operating at several-MHz switching frequency. However, the conventional ones mostly have high voltage stress on the switch, roughly 4–5 times the input voltage. In this paper, we propose the single-switch converter topologies derived from the drain-source impedance networks consisting of two inductors and two capacitors. The switch voltage of the proposed converters is shaped into a near trapezoid by designing the resonant networks to have the desired drain-source impedance. Furthermore, a simple and specific design scheme is presented here so that the peak switch voltage is lowered to 2.2–2.5 times the input voltage while zero voltage switching is achieved. Experimental results from a 20-W GaN-based prototype operating at 10 MHz demonstrate the feasibility of the proposed converter topologies and the design method. [ABSTRACT FROM AUTHOR]