Search

Renewable energy is an advisable choice to reduce fuel consumption and $\rm CO_{2}$ emission. Therein, wind energy and solar energy are the most promising contributors to reach this goal. Although the hybrid wind/solar system has been widely studied, the real-time current sharing based on their maximum capacities is rarely achieved in terms of seconds. Based on this, this paper proposes an accurate current sharing and voltage regulation approach in hybrid wind/solar systems, which is based on distributed adaptive dynamic programming approach. Firstly, the equivalent wind/solar model is built, which is an indispensable preprocessing to achieve the complementary between wind energy and solar energy. Therein, the wind energy and solar energy can output relative current according to their respective capacity ratio, which ensure the maximum utilization ratio of renewable energy source. Furthermore, current sharing and voltage regulation problem is switched into optimal control problem. Under this effect, each source agent aims to obtain the optimal control variable and achieve accurate current sharing/voltage regulation. Moreover, an adaptive dynamic programming approach based on Bellman principle is proposed. It can achieve accurate current sharing and voltage regulation. Finally, the simulation results are provided to illustrate the performance of the proposed adaptive dynamic programming approach. [ABSTRACT FROM AUTHOR]

In dc microgrid, energy storage system (ESS) plays a crucial role to provide short-or-long term and high-quality electric energy. The different control strategies for bidirectional dc-dc converter (BDC) of ESS in grid-tied and islanded modes pose challenges to the coordination control of the dc microgrid. This paper proposes an autonomous control scheme for the BDC in dc microgrid. The proposed control scheme is based on $V^2-P$ droop control and unifies bus voltage regulation and power regulation in a single control structure. Thus, global smooth transition between various operation modes can be achieved without any control strategy changes, which avoids various mode switch detection mechanisms and improves system stability. Furthermore, the proposed control scheme is fully decentralized which reduces the reliance on communication, and enhances the reliability of the microgrid. On the other hand, $V^2-P$ droop approach eliminates the negative effect of widespread constant power loads (CPLs) in dc microgrid. The stability of the proposed control method is illustrated, and the design guideline of some critical control gains is addressed. Finally, the effectiveness of the proposed control scheme is validated by the real-time hardware-in-loop (HIL) platform. [ABSTRACT FROM AUTHOR]

This article investigates the current sharing and voltage regulation problem of a DC microgrid by a distributed supervisory control method. In the existing secondary control methods, current sharing feedback control loop and voltage regulation feedback control loop are linearly integrated to shift the droop equation. However, the linear combination of two loops may easily offset the control effect of each other, as the control dimension is less than the objective dimension. This fact motivates us to design a distributed supervisory secondary control (DSSC) scheme to achieve a more flexible configuring of each converter. The DSSC consists of two candidate controllers and a supervisor. The two controllers refer to current sharing configuring and DC bus voltage regulation respectively, and the supervisor is to orchestrate the switching between candidate controllers based on the system environment of DC microgrid. Under the proposed DSSC, each converter selects to configure the current sharing or regulates the DC bus voltage according to its need. Theoretical stability analysis is rigorously conducted. Finally, both simulation and experiment results are presented to demonstrate the effectiveness of DSSC. [ABSTRACT FROM AUTHOR]

In this article, a fixed and smooth-switch-sequence modulation strategy is proposed to equalize the dc-link voltages among the cascaded rectifier. The structure of a single-phase three-level neutral-point-clamped cascaded rectifier is studied. Three core steps of this strategy are analyzed respectively, including carrier wave disposition calculation, fixed pulse generator, and voltage rank function. In addition, a criterion of the degree of the load unbalance is established in order to measure the voltage balancing boundary of the presented approach. The superiorities of the proposed control strategy embody the smooth switch sequence, the strong voltage balance capability, as well as the fixed switch sequence. Owe to these advantages, the cascaded rectifier could effectively reduce the switching frequency, achieve the goals of voltage balancing, and reduce the calculation burden of the controller when the number of cascaded modules is large. The effectiveness of the proposed strategy is verified by simulation and experiment results. [ABSTRACT FROM AUTHOR]

This paper presents a uniform control strategy for the bidirectional ac/dc interlinking converter (BIC) in hierarchical controlled hybrid microgrid. The uniform control strategy unifies different control structures for multifunctional BIC in terms of power management, ac and dc voltage support. With the unified control structure, various triggering mechanisms for BIC mode-switch are not compulsory in response to the relevant scenario changes in the power network. Therefore, the negative consequences, such as unsmooth transition and system collapse due to the inaccurate or slower mode switch, can be avoided. Moreover, the uniform control strategy is also applicable for the hierarchical controlled hybrid microgrid, whose control architecture is typically comprised of the centralized and decentralized levels. This enables the communication fault ride-through capability and the impact from the communication failures can thus be mitigated. To sum up the above two features, the proposed control strategy is able to provide a smooth operation for the BIC without control mode switch in the event of unintentional scenario changes in power or communication network. To verify the validity of the proposed uniform control strategy, the controller hardware-in-the-loop experimental results have been provided in this paper. [ABSTRACT FROM PUBLISHER]

Modularity and high reliability from redundancy are the two attractive advantages of modular multilevel converters (MMCs). This paper elaborates a switch open-circuit fault diagnosis and a fault-tolerant operation scheme for MMCs with distributed control. The proposed fault diagnosis and fault-tolerant control method can significantly improve the reliability of the MMC while maintaining the modularity of its software implementation. By distributing fault diagnosis into submodules, its local controller is capable of identifying the switching devices in open-circuit fault without extra hardware circuitry. Based on the real-time measurements of submodule terminal voltage and arm current, single, or multiple faulty switches can be identified within 3.5 ms without triggering faulty alarms. Furthermore, a new fault-tolerant operation is proposed to maintain the output current, internal dynamics, and switching harmonics unchanged after the faulty submodule is bypassed. This is achieved by resetting the period and phase registers in the local controller according to the information of bypassed submodules. The control loops of the MMC are not influenced by the proposed fault diagnosis and fault-tolerant operation, making the operation transition seamless and reliable. Experimental results show that fault identification and system reconfiguration can be completed within 5 ms, and the MMC can seamlessly and smooth ride through the switch open-circuit faults without severe malfunction and catastrophic damages. [ABSTRACT FROM AUTHOR]

The traditional finite-control-set model predictive control (FCS-MPC) method for a cascaded H-bridge (CHB) rectifier has two main issues: heavy computational burden and low steady-state current performance. In this paper, a novel FCS-MPC method has been proposed for a single-phase CHB rectifier. The proposed method solves the optimization problem of FCS-MPC for one cell by one cell, like a “pipeline.” In the proposed method, the sampling period is divided into equal intervals by the number of cells. At the beginning of the first interval, the first cell selects its switching state to be applied. Then, the following cell selects its switching state to be applied at the beginning of next interval. Finally, the selected switching state of last cell will be applied at the beginning of the last interval. A cost function presenting the control objectives of common source current error and itself dc-link voltage error is evaluated for each cell. A single-phase three-cell CHB rectifier controlled by a DSpace DS1104 is tested and the experimental results show that a significant reduction in computational time, an improved steady-state current performance, and a comparable dynamic response are achieved in the proposed method in comparison with the traditional FCS-MPC method. [ABSTRACT FROM AUTHOR]