Search

Purpose: Three-dimensional (3D) autotransplantation is a technique for surgical transposition of a tooth to another site within one patient, using 3D printed replicas of the donor tooth. In this study, we evaluated intraoperative experiences during 3D autotransplantation of teeth., Materials and Methods: A multicenter prospective clinical study was implemented. All procedures were performed using preoperative cone-beam computed tomography imaging and computer-assisted design with computer-assisted manufacturing resulting in a 3D replica of the donor tooth., Results: The 100 autotransplantation procedures (79 patients) included canines, premolars, molars, and 1 supernumerary tooth. In 82% of the procedures, the transplantation was performed with an extra-alveolar time of less than 1 minute and an immediate good fit of the donor tooth. In 14%, the extra-alveolar time was 1 to 3 minutes or multiple fitting attempts were necessary. In 4%, the extra-alveolar time exceeded 3 minutes. Difficulties during the procedures were caused by movement artifacts on the preoperative cone-beam computed tomography imaging, a long interval between the imaging and the procedure, or insufficient bone volume at the recipient site., Conclusions: The use of a 3D printed donor tooth replica during autotransplantation procedures minimized the extra-alveolar time and intraoperative fitting attempts of transplants. This facilitated a quick and reliable treatment and enabled more difficult procedures., (Copyright © 2019 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.)

This systematic review provides an overview of studies on autotransplantation techniques using rapid prototyping for preoperative fabrication of donor tooth replicas for preparation of the neo-alveolus. Different three-dimensional autotransplantation techniques and their treatment outcomes are discussed. The systematic literature search yielded 19 articles that satisfied the criteria for inclusion. These papers described one case-control study, four clinical observational studies, one study with a clinical and in vitro part, four in vitro studies, and nine case reports. The in vitro studies reported high accuracy for the printing and planning processes. The case reports all reported successful transplantation without any pathological signs. The clinical studies reported a short extraoral time of the donor tooth, with subsequent success and survival rates of 80.0-91.1% and 95.5-100%, respectively. The case-control study reported a significant decrease in extraoral time and high success rates with the use of donor tooth replicas. In conclusion, the use of a preoperatively designed surgical guide for autotransplantation enables accurate positional planning, increases the ease of surgery, and decreases the extraoral time. However, the quality of the existing body of evidence is low. Further research is therefore required to investigate the clinical advantages of this innovative autotransplantation technique., (Copyright © 2017 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.)

Purpose: The aim of the present cadaveric study was to assess the accuracy of computer-assisted template-guided autotransplantation of teeth with custom 3-dimensional (3D) designed/printed surgical tooling., Materials and Methods: Ten partially edentulous human mandibular cadavers were scanned using a cone-beam computed tomography (CBCT) system and an intraoral scanning system. The 3D data of these cadavers were imported to specialized software and used to analyze the region of the recipient sites, and the donor teeth were selected. Subsequently, congruent to the donor teeth, custom surgical tooling and surgical-guided templates were designed and 3D printed. The guided osteotomies were performed and the donor teeth transplanted. To evaluate the planned donor teeth positions compared with the transplanted donor teeth positions, the mandibles were scanned again using the CBCT system, and software matching was applied to measure the accuracy of the procedure., Results: The mean angular deflection of the transplanted donor teeth with the planned donor teeth positions was 5.6 ± 5.4°. Comparing the 3D positions of the shoulders, a mean deviation of 3.15 ± 1.16 mm and a mean apical deviation of 2.61 ± 0.78 mm were found., Conclusions: The described method of computer-assisted template-guided autotransplantation of teeth with custom 3D designed/printed surgical tooling could potentially provide a relatively accurate alternative for the currently available treatment approaches. Further research should focus on improving the accuracy of this technique and evaluating the clinical success and advantages of this method., (Copyright © 2017 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.)

Purpose: The aim of this study was to introduce a novel method for accurate autotransplantation with computer-assisted guided templates and assembled custom-designed surgical tooling and to test the feasibility and accuracy of this method ex vivo., Materials and Methods: A partially edentulous human mandibular cadaver was scanned with a cone-beam computed tomography (CBCT) system and an intraoral scan system. The 3-dimensional (3D) data of this cadaver were imported into specialized software and used to analyze the region of the recipient site and the donor tooth was selected. Subsequently, congruent to the donor tooth, custom surgical tools and a surgical guided template were designed and 3D printed. The guided osteotomy was performed and the donor tooth was transplanted. To evaluate the planned position of the donor tooth in relation to the position of the transplanted donor tooth, the mandible with the transplanted donor tooth was rescanned with the CBCT system and software matching was applied to measure the accuracy of the procedure., Results: The angular deflection of the transplanted donor tooth in relation to the planned donor tooth position was 3.1°. When comparing the 3D positions of the shoulder, there was a deviation of 1.25 mm and an apical deviation of 0.89 mm., Conclusion: With the use of currently available technology, it is feasible to accurately plan and create in a virtual simulation a donor tooth position with congruent custom surgical tools and to transfer this to a clinical setting with 3D printing. However, further research on multiple levels is needed to explore this novel approach., (Copyright © 2016 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.)