Search

An Fe-based coating was thermally sprayed onto the surface of AZ91 magnesium alloy via the High-Velocity-Oxygen-Fuel (HVOF) method. The thermally sprayed coating with a thickness of 530 ± 25 µm and a porosity of 0.7 ± 0.1% did not show any macrostructural defects and did not cause any degradation of the AZ91 alloy. Laser remelting of the surface layer of the sprayed coating resulted in the recrystallization of the structure and the disappearance of presented pores, splat boundaries, and other defects. This led to an increase in the hardness of the remelted layer from the original 535 ± 20 HV0.3 up to 625 ± 5 HV0.3. However, during the laser remelting at a laser power of 1000 W, stress cracking in the coating occurred. The tribological properties were evaluated by the ball-on-plate method under dry conditions. Compared to the uncoated AZ91 magnesium alloy, a higher value of friction coefficient (COF) was measured for the as-sprayed coating. However, there was a decrease in wear rate and weight loss. The remelting of the surface layer of the as-sprayed coating led to a further decrease in the wear rate and weight loss. Based on the obtained data, it has been shown that the application of laser-remelted thermally sprayed Fe-based coatings on AZ91 Mg alloy improves hardness and tribological properties compared to bare Mg alloy and as-sprayed Fe-based coatings. [ABSTRACT FROM AUTHOR]

This paper deals with the study of the crystallization and phase transformation of Ni-P coatings deposited on AZ91 magnesium alloy. Prepared samples were characterized in terms of surface morphology and elemental composition by means of scanning electron microscopy with energy-dispersive spectroscopy analysis. The results of X-ray diffraction analysis and differential scanning calorimetry suggested that increasing the phosphorus content caused Ni-P coatings to develop an amorphous character. The crystallization of Ni was observed at 150, 250, and 300 °C for low-, medium- and high-phosphorus coatings, respectively. The Ni crystallite size increased with increasing temperature and decreasing P content. Conversely, the presence of the Ni3P phase was observed at a maximum peak of 320 °C for the high-phosphorus coating, whereas the crystallization of the Ni3P phase shifted to higher temperatures with decreasing P content. The Ni3P crystallite size increased with increasing temperature and increasing P content. An increase in microhardness due to the arrangement of Ni atoms and Ni3P precipitation was observed. The deposition of as-deposited Ni-P coatings led to an improvement in the corrosion resistance of AZ91. However, the heat treatment of coatings resulted in a deterioration in corrosion properties due to the formation of microcracks. [ABSTRACT FROM AUTHOR]

The corrosion behavior of duplex Ni-P coatings deposited on AZ91 magnesium alloy was studied. The electroless deposition process of duplex Ni-P coating consisted in the preparation of low-phosphorus Ni-P coating (5.7 wt.% of P), which served as a bond coating and high-phosphorus Ni-P coating (11.5 wt.% of P) deposited on it. The duplex Ni-P coatings with the thickness of 25, 50, 75 and 100 µm were deposited on AZ91 magnesium alloy. The electrochemical corrosion behavior of coated AZ91 magnesium alloy was investigated by electrochemical impedance spectroscopy and potentiodynamic polarization method in 0.1 M NaCl. Obtained results showed a significant improvement in the corrosion resistance of coated specimens when compared to uncoated AZ91 magnesium alloy. From the results of the immersion tests in 3.5 wt.% NaCl, 10% solution of HCl and NaOH and 5% neutral salt spray, a noticeable increase in the corrosion resistance with the increasing thickness of the Ni-P coating was observed. [ABSTRACT FROM AUTHOR]