Search

This work investigated two titanium-based alloys with a constant tantalum content and variable contents of alloy additives – niobium and zirconium. The Ti-30Ta-10Zr-20Nb (wt.%) and Ti-30Ta-20Zr-10Nb (wt.%) alloys were obtained using a combination of powder metallurgy and arc melting methods. The influence of alloying additives on the structure and properties of the Ti-Ta-Nb-Zr system was studied using, among others: X-ray diffraction and scanning electron microscopy. The X-ray diffraction confirmed the single-β-phase structure of both alloys. In addition, the microscopic analysis revealed that a higher amount of zirconium favoured the formation of larger grains. However, the microhardness analysis indicated that the alloy with the higher niobium content had the higher microhardness. Importantly, the in vitro corrosion study revealed that the addition of niobium promoted the better corrosion resistance of the investigated alloy. [ABSTRACT FROM AUTHOR]

Scientists and medics are still searching for new metallic materials that can be used in medicine, e.g., as material for implants. The following article proposes materials based on titanium with vital elements prepared by combined powder metallurgy and arc melting methods. Four compositions of Ti-28Ta-9Nb, Ti-28Ta-19Nb, Ti-28Ta-9Zr and Ti-28Ta-19Zr (wt.%) have been prepared. The tested material was thoroughly analyzed by X-ray diffraction and scanning electron microscopy. Qualitative phase analysis using X-ray diffraction showed the presence of two phases, a' and ß titanium. In addition, a microhardness test was conducted, and the material was characterized in terms of corrosion properties. It was found that the corrosion resistance decreases with an increase of the ß phase presence. [ABSTRACT FROM AUTHOR]

This work investigated two titanium-based alloys with a constant tantalum content and variable contents of alloy additives - niobium and zirconium. The Ti-30Ta-10Zr-20Nb (wt.%) and Ti-30Ta-20Zr-10Nb (wt.%) alloys were obtained using a combination of powder metallurgy and arc melting methods. The influence of alloying additives on the structure and properties of the Ti-Ta-Nb-Zr system was studied using, among others: X-ray diffraction and scanning electron microscopy. The X-ray diffraction confirmed the single-ß-phase structure of both alloys. In addition, the microscopic analysis revealed that a higher amount of zirconium favoured the formation of larger grains. However, the microhardness analysis indicated that the alloy with the higher niobium content had the higher microhardness. Importantly, the in vitro corrosion study revealed that the addition of niobium promoted the better corrosion resistance of the investigated alloy. [ABSTRACT FROM AUTHOR]

In this paper, the influence of Mo addition on the structure and mechanical properties of the NiCoMnIn alloys have been studied. Series of polycrystalline NiCoMnIn alloys containing from 0 to 5 mas.% of Mo were produced by the arc melting technique. For the alloys containing Mo, two-phase microstructure was observed. Mo-rich precipitates were distributed randomly in the matrix. The relative volume fraction of the precipitates depends on the Mo content. The numbers of the Mo rich precipitates increases with the Mo contents. The structures of the phases were determined by the TEM. The mechanical properties of the alloys are strongly affected by Mo addition contents. Brittleness of the alloys increases with the Mo contents. [ABSTRACT FROM AUTHOR]

The results of the present investigation are focused on the structure examinations of a commercial Al-3%Mg alloy in different conditions using an optical microscope (OM), scanning electron microscopy (SEM), the EBSD technique, transmission electron microscopy (TEM) and X-ray diffraction (XRD). Measurements of the microhardness and ultimate tensile strength were carried out to evaluate the influence of ECAP and post-ECAP treatment on the mechanical properties. In this study, we found that 6 ECAP passes via route B c result in a significant grain refinement. The measured average grain size of the as deformed sample was about 0.43 μm. As a result of the performed post-ECAP heat treatment (artificial ageing), a material with a more homogenous microstructure, having an average grain size of ~ 0.68 μm, was obtained. The results of the mechanical property measurements show a significant increase in mechanical strength to about ~ 384 [MPa] in the T9 condition and to ~ 330 [MPa] after post-ECAP treatment (T8 condition). The high strength of the alloy in the T9 condition is suggested to be related to grain size strengthening, dislocation strengthening and precipitation strengthening. An increase in elongation/ductility from 2.4% to 11.2% was observed in the T8 condition sample, which is a result of the grain growth and the dislocation density decrease. [ABSTRACT FROM AUTHOR]