Search

This paper focuses on the condition where a reinforced concrete (RC) deep beam is subjected to two concentrated loads (P1 and P2), which are positioned at respective distances a and c from bottom supports. In general, equal shear spans (a = c) and equal point loads (P1 = P2) are commonly assumed in most experimental programmes. Nevertheless, such cases are rare in practice. In contrast, due to the fact that deep beam floor normally subjects to irregular layout of column grid, deep beams are usually subjected to unequal load magnitude (load inequality or P1 ≠ P2) and unsymmetrical load positions (load asymmetry or a ≠ c). Although previous research has demonstrated the significant influences of load asymmetry and inequality on the structural performance of deep beams at room temperature, no research programme has been performed to study their influences on the fire performance of deep beams. As a result, this study is proposed to investigate the shear behaviour of unsymmetrically-loaded deep beams at fire condition, analytically and experimentally. The current research first derives a strut-and-tie-model (STM) to predict the shear capacity of RC deep beams under unequal/unsymmetrical loading conditions and at elevated temperatures. The STM takes into account the effects of unsymmetrical loading configurations, contribution of steel reinforcement on strut capacity, and thermal-induced gradient. Additionally, a test programme on six RC deep beams under fire condition is conducted for verification of the proposed model. Observations from this experimental programme show that load asymmetry and inequality have different effects on the fire performance of deep beams. To be more specific, an increase in load inequality leads to an alteration in failure mode of the deep beams, whist load asymmetry does not affect the failure mode as much. On the other hand, increasing load inequality can result in a significantly increased mid-span deflection at failure and a slightly increased failure time. Besides, effect of load inequality on deflection and failure duration depends on the loading positions. Furthermore, the proposed STM yields good agreement between test data and model predictions for unequally- and/or unsymmetrically-loaded deep beams, at both room and high temperatures. Ministry of National Development (MND) National Research Foundation (NRF) This research work is supported by the Singapore Ministry of National Development and National Research Foundation under L2 NIC Award No. L2NICCFP1-2013-4.

OpenSees is an open-source object-oriented software framework developed at UC Berekeley. The OpenSees framework has been recently extended to deal with structural behaviour under fire conditions. This paper summaries the key work done for this extension and focuses on the validation and application of the developed OpenSees to study the behaviour of composite steel-concrete beams under fire conditions. The performance of the developed OpenSees are verified by four mechanical tests and two fire tests on simply supported composite beams. A parametric study is carried out using OpenSees to study the influence of boundary condition as well as composite effect of slab on the behavior of composite beams exposed to fire. The stress and strain along the beam section is output and compared with yield stress limit at elevated temperature to explain these influences in detail. The results show that the stress distribution in the web of the steel beam is more complex due to the support effects.

This is the post-print version of the final paper published in Engineering Structures. The published article is available from the link below. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. Copyright @ 2008 Elsevier B.V. It is evident from a series of tests on simply supported reinforced concrete slabs that the failure of the slabs at large deflections is due to the formation of individual large cracks. This failure mode was also observed in the Cardington full-scale fire tests. Previous research indicates that the global behaviour of concrete slabs subject to large deflections can be well predicted by the smeared cracking model; however, the model cannot quantitatively predict the openings of individual cracks within the slabs at large deflections. For the discrete approach it is usually assumed that the cracks are formed along element edges, therefore continuous re-meshing is required during the analysis. Consequently, the results are mesh-dependent and the computing cost is high. In recent years, mesh independent finite element procedures, such as embedded (EFEM) and extended (XFEM) approaches, were widely used for modelling of the crack initiation and growth in structural members. However, most of the meshless models developed are either based on in-plane loading conditions or confined to thin shells with assumed full-depth cracks, which form apparent displacement jumps within an element. For a reinforced concrete slab, an out-of-plane load causes coupled stretching and bending of the slab, cracks are usually initiated at discrete positions and then propagated, until at last some individual full-depth cracks are formed. Pure stretching or assumed full-depth cracking is inadequate for modelling this kind of failure. Therefore, in this research, a non-linear layered procedure with embedded weak discontinuity is developed to quantitatively model the progressive tensile failure of reinforced concrete slabs subjected to large deflections. The current model inherits the advantage of the smeared approach, and at the same time, introduces the opening width of crack explicitly by taking the advantage of the better description of the kinematic characteristics of the EFEM approach. A series of validations have been conducted against test data at both ambient and elevated temperatures, and the research shows that the model developed in this paper is not sensitive to the FE mesh size and the aspect ratio of the slab. The results predicted by the model developed agreed well with the test data in terms of deflection and crack open width, also agreeing well with those modelled by the smeared model. Hence, this new approach provides a numerical method to predict the load capacity as well as identifying the occurrence and severity of crack failure in reinforced concrete slabs subjected to extreme loading conditions, such as fire.

The main objective of this paper is to investigate the effect of adding discrete glass fibers on the behavior of reinforced concrete (RC) beams under different fire and cooling conditions. Eighteen beams with different concrete compressive strengths were tested to study the behavior of reinforced concrete (RC) beams containing discrete glass fibers when exposed to different fire and cooling conditions. Nine beams were prepared from normal strength concrete (NSC) with compressive strength equal to 35 MPa while the other beams were prepared from high strength concrete (HSC) with compressive strength equal to 60 MPa. The beams contained different contents of discrete glass fibers. The modes of failure of tested specimens show that the crack patterns change according to fire condition and fiber content. Analysis of test results show that adding discrete glass fibers to NSC increased the residual stiffness of the tested specimens after firing and decreased the rate of the deflection gain during firing. Also adding fibers to concrete has a limited positive effect on the ultimate strength of the specimens compared to the control specimens. Its effect on deflection due to fire is more pronounced. Finally, the recommended optimum ratio of discrete glass fibers is not more than 0.5% of the total concrete weight.