Search

This study aimed to develop a new model, valid for soil with and without expandable characters, to estimate volumetric soil water content (&theta, ) from readings of scaled frequency (SF) acquired with the Diviner 2000&reg, sensor. The analysis was carried out on six soils collected in western Sicily, sieved at 5 mm, and repacked to obtain the maximum and minimum bulk density (&rho, b). During an air-drying process SF values, the corresponding gravimetric soil water content (U) and &rho, b were monitored. In shrinking/swelling clay soils, due to the contraction process, the variation of dielectric permittivity was affected by the combination of the mutual proportions between the water volumes and the air present in the soil. Thus, to account for the changes of &rho, b with U, the proposed model assumed &theta, as the dependent variable being SF and &rho, b the independent variables, then the model&rsquo, s parameters were estimated based on the sand and clay fractions. The model validation was finally carried out based on data acquired in undisturbed monoliths sampled in the same areas. The estimated &theta, &theta, estim, was generally close to the corresponding measured, &theta, meas, with Root Mean Square Errors (RMSE) generally lower than 0.049 cm3 cm&minus, 3, quite low Mean Bias Errors (MBE), ranging between &minus, 0.028 and 0.045 cm3 cm&minus, 3, and always positive Nash-Sutcliffe Efficiency index (NSE), confirming the good performance of the model.

The objective of this paper was to assess the performance of Hydrus-2D model to simulate the effects of different on-farm irrigation strategies applied on potato crop. The ability of the model to simulate the stress coefficient (Ks), obtained as the ratio between actual and maximum transpiration, and to define the productive function of potato crop under the semi-arid conditions of central Tunisia were also evaluated. Experiments were carried out on potato crop under full (FI) and deficit irrigation (DI) and two different water qualities supplied by means of a subsurface drip irrigation system. Results evidenced that the model, despite some discrepancies locally observed, can fairly accurately predict soil water contents and electrical conductivity around buried emitters. Furthermore, under water and salt stress conditions, &ldquo, measured&rdquo, Ks, based on crop water stress index (CWSI) obtained on thermal images, resulted in a good correlation with the corresponding estimated by the model (R2 = 0.8). The database collected during the three growth seasons also allowed the definition of the crop productive function represented by a linear relationship between the relative yield loss and Ks. This function represents a useful guidelines for the sustainable use of irrigation water in countries characterized by a semi-arid climate and a limited availability of water for irrigation.

[EN] The knowledge of the crop response to soil water deficit is essential to predict the actual crop water requirements under limited soil water conditions. The mathematical schematization of the crop response under RDI can allow identifying the exact irrigation timing. The threshold of soil water status below which crop transpiration decreases represents a key parameter for the water stress functions. The main objective of this paper was to investigate the effects of several RDI treatments, applied during the three stages of fruit growth, on soil-plant-water relations of drip-irrigated mandarin trees. Experiments were carried out in seven irrigation treatments: a control, irrigated at 125% of potential evapotranspiration measured in weighting lysimeters, ETlys, during the whole year, and six RDI treatments in which 25% and 50% of ETlys were applied during each of the three stages of fruit growth. The critical threshold of soil water status expressed in terms of soil water depletion below which predawn (PLWP) and midday (MSWP) leaf water potential is affected by decreasing soil water content, were identified. The dependency of crop water status from the climate forcing, occurring under soil water contents higher than the critical threshold was also demonstrated. Moreover, a strong relationship between water stress integral ( ) evaluated during the three stages of fruit growth, and the corresponding amount of water applied (irrigation and precipitation) was observed after normalizing the variables. The robust relationship between these two variables (R2 = 0.83) confirmed that the water stress integral represents a good indicator of the plant-water relationship and allows the prediction of the total irrigation depth to be applied to achieve a desired stress level during the fruit growth. Moreover, this relationship depends on the irrigation schedule adopted to regulate the deficit, which includes the irrigation variables, such as irrigation dose and its variability., The research was carried out in the frame of Progetto Organizzazioni di Produttori-Illuminati Frutta-Rallo (University of Pisa, 1048 Ministero delle Politiche Agricole e Forestali-Regione Toscana) and ATMOSMART-dimostratore tecnologico (University of Pisa).

Accurate soil water status measurements across spatial and temporal scales are still a challenging task, specifically at intermediate spatial (0.1–10 ha) and temporal (minutes to days) scales. Consequently, a gap in knowledge limits our understanding of the reliability of the spatial measurements and its practical applicability in agricultural water management. This paper compares the cumulative EM38 (Geonics Ltd., Mississauga, ON, Canada) response collected by placing the sensor above ground with the corresponding soil water content obtained by integrating the values measured with an FDR (frequency domain reflectometry) sensor. In two field areas, characterized by different soil clay content, two Diviner 2000 access tubes (1.2 m) were installed and used to quantify the dimensionless fraction of transpirable soil water (FTSW). After the calibration, the work proposes the combined use of the FDR and electromagnetic induction (EMI) sensors to measure and map FTSW. A strong correlation (R2 = 0.86) between FTSW and EM38 bulk electrical conductivity was found. As a result, field changes of FTSW are due to the variability of soil water content and soil texture. As with the data acquired in the field, more structured patterns occurred after a wetting event, indicating the presence of subsurface flow or root water uptake paths. After assessing the relationship between the soil and crop water status, the FTSW domain includes a critical value, estimated around 0.38, below which a strong reduction of relative transpiration can be recognized.

The paper analyzes the performance of Hydrus-2D model to simulate the dynamic of soil water contents and transpiration fluxes in an olive orchard in which two different irrigation systems were used in 2011 and 2012. The relationship between measured midday stem water potential, MSWP, and simulated relative transpiration (ratio between simulated actual and maximum crop transpiration), Ks, was also identified with the aim to use the model for crop water status predictions. Finally, a scenario analysis was carried out for irrigation management purposes, by considering the level of crop water stress achieved in the different phases of the vegetative growth. The results evidenced that active roots (d

In this paper the suitability of the HYDRUS-2D model to simulate volumetric soil water content in the root zone of a potato crop under subsurface drip irrigation (SDI) is initially assessed on the basis of a field study. Then, considering that the crop is moderately sensitive to soil salinity, the model is tested to predict the salt distribution around a buried emitter, when two different water qualities (i.e. electrical conductivity of 1.0 and 4.0 dS m-1) are used during the growing season (treatments T1 and T2). Finally, the soil volume in which salt accumulates is distinguished by the model for the two treatments, for which the respective yields are not significantly different. The results showed that in the root zone, simulated and measured soil water content (SWC) are fairly close. HYDRUS-2D well enough predicts the average salt concentration in the soil and evaluates the dynamic of mass-conservative solutes around buried emitters. In both treatments, the salt concentration resulted in an increase in the wetting bulb, with a maximum located towards the edge of the wetting bulb and near the soil surface. Copyright © 2015 John Wiley & Sons, Ltd. Resume Dans cet article, HYDRUS-2D a ete utilise pour l'estimation de la teneur en eau volumique dans la zone racinaire d'une culture de pomme de terre, irriguee au goutte a goutte enterre dans les conditions climatiques tunisiennes. Le modele a ete utilise pour l'estimation de la distribution du sel autour du goutteur enterre pour deux qualites differentes d'eau caracterisees par des conductivites electriques egales a 1.0 et 4.0 dS m-1, respectivement (traitements T1 et T2). Le modele permet de predire le volume du sol dans lequel les sels s'accumulent. Selon le test Student (t), les valeurs de la teneur en eau volumique du sol dans la zone racinaire qui sont prevues par HYDRUS-2D sont significativement correlees aux valeurs reelles mesurees en T1 et T2. Les resultats ont egalement mis en evidence que le modele est capable d'estimer la concentration moyenne de sel dans le sol et d'evaluer la dynamique des solutes a conservation de masse autour d'un goutteur enterre. En outre, dans les deux traitements, la concentration de sel augmente a l'interieur du bulbe, avec un maximum de concentration de sel situee dans le front d'humectation et a proximite de la surface du sol. La concentration de sel dans T2 est legerement plus elevee que dans T1. Cependant, la salinite de l'eau legerement elevee utilisee pour l'irrigation n'a pas affecte significativement la transpiration reelle de la pomme de terre et par consequent son rendement. Copyright © 2015 John Wiley & Sons, Ltd.

The knowledge of soil water content (SWC) dynamics in the upper soil layer is important for several hydrological processes. Due to the difficulty of assessing the spatial and temporal SWC dynamics in the field, some model-based approaches have been proposed during the last decade. The main objective of this work was to assess the performance of two approaches to estimate SWC in the upper soil layer under field conditions: the physically-based thermal inertia and the Hydrus model. Their validity was firstly assessed under controlled laboratory conditions. Thermal inertia was firstly validated in laboratory conditions using the transient line heat source (TLHS) method. Then, it was applied in situ to analyze the dynamics of soil thermal properties under two extreme conditions of soil-water status (well-watered and air-dry), using proximity remote-sensed data. The model performance was assessed using sensor-based measurements of soil water content acquired through frequency (FDR) and time domain reflectometry (TDR). During the laboratory experiment, the Root Mean Square Error (RMSE) was 0.02 m3 m−3 for the Hydrus model and 0.05 m3 m−3 for the TLHS model approach. On the other hand, during the in situ experiment, the temporal variability of SWCs simulated by the Hydrus model and the corresponding values measured by the TDR method evidenced good agreement (RMSE ranging between 0.01 and 0.005 m3 m−3). Similarly, the average of the SWCs derived from the thermal diffusion model was fairly close to those estimated by Hydrus (spatially averaged RMSE ranging between 0.03 and 0.02 m3 m−3).

[EN] Micro-irrigation is considered one of the most efficient water distribution systems and allows increasing water use efficiency if coupled with effective water-saving irrigation management strategies as regulated deficit irrigation (RDI) or partial root-zone drying (PRD) techniques. However, application of these strategies makes it crucial the real-time monitoring of soil and crop water status, in order to identify appropriate irrigation scheduling parameters (irrigation timing and doses) and to prevent irreversible damage of plant system and/or crop yield reductions. Even if midday stem water potential (MSWP) is considered one of the most affordable indicator for direct determinations of crop water status, its measurement requires skilled operators, is destructive and time consuming, so that indirect and fast estimations are desirable. In this direction, agro-hydrological models can be considered an easy-to-use tool for indirect evaluations of soil and crop water status aimed to identify irrigation scheduling parameters even when micro-irrigation distribution systems and water saving management strategies are adopted. The paper, after examining the eco-physiological response of citrus orchards to soil water deficit, assessed the potential of FAO-56 agro-hydrological modelto identify the crop water stress under different irrigation management strategies. Experiments carried out during three years (2009–2011) allowed identifying the crop water stress response to soil water deficit conditions, also confirming the schematization proposed in FAO-56 paper for citrus orchards. Moreover, after evaluating the similarity between the measured MSWP with the simulated crop water stress coefficient, Ks, it was proved the fairly good performance of FAO-56 agrohydrological model to predict soil water content (RMSE = 0.04 m3 m−3), from one side, and the crop response to different irrigation management strategies, from the other. The obtained results evidenced that the crop water stress coefficient estimated by the model can be used as a suitable indicator to replace the tedious and time-consuming field measurements of MSWP. © 2016 Elsevier B.V. All rights reserved., Research was carried out in the frame of the PRIN 2010 projects, co-financed by Ministero dell'Istruzione, dell'Universita e della Ricerca (MIUR) and Universita degli Studi di Palermo. Authors wish to thank the Committee for International Relations Office (CORI) of University of Palermo to support the research cooperation with the Polytechnic University of Valencia.

The main objective of the work is to optimize drip installation depth for Eggplant crop irrigated with surface or subsurface drip irrigation systems to improve irrigation Water Use Effeciency (WUE), by means of field measurements and simulations carried out with Hydrus-2D model. Initially, a comparison between simulated Soil Water Contents (SWC) and the corresponding measured in two plots, in which laterals with coextruded emitters are laid on the soil surface (T0) and at 20 cm depth (T20), respectively. In order to choose the best position of the lateral, the results of different simulation run, carried out by choosing a deeper installation (T45) depth. Simulated SWC’s resulted fairly close to the corresponding measured at different distances from the emitter and therefore the model was able to predict SWC’s in the root zone with values of the Root Mean Square Error generally lower than 4%. This result is consequent to the appropriate schematization of the root distribution, as well as of the root water uptake. The values of WUE associated to the different examined installation depths tend to a very slight increase when the position of the lateral is situated on 20 cm and start to decrease for the higher depths.

The knowledge of crop response to water stress is crucial to predict transpiration reductions under limited soil water conditions and for a rational scheduling of irrigation. In order to assess whatever water stress model, it is necessary to estimate critical thresholds of soil water status, below which plant transpiration starts to decrease. The main objective of the work is to identify the shape and to determine the parameters of table olive orchards (Olea europaea, var. Nocellara del Belice) water stress function, assessed according to relative transpiration or leaf/stem water potential. In order to assess different water stress functions describing the eco-physiological field response to soil water status, an experimental campaign was carried out in a farm located in South-West coast of Sicily. Meteorological data and soil and crop water status were monitored during irrigation seasons 2008 and 2009. A value of soil matric potential of about −40 m was identified as the threshold below which actual transpiration decreases with decreasing soil water content. For values of soil matric potential higher than the critical threshold, actual transpiration resulted almost constant. A similar behavior was observed when the xylematic leaf/stem water potentials were used to quantify the crop water stress. Investigation also showed that the non-linear models better reproduced the initial phase of the transpiration reduction process; for the examined crop, in fact, convex shape models, typical of xerophytes, better reproduce the reductions of actual transpiration under the soil water deficit conditions recognized in the field.

Correct estimation of crop actual transpiration plays a key-role in precision irrigation scheduling, since crop growth and yield are associated to the water passing through the crop. Objective of the work was to assess how the combined use of micro-meteorological techniques (eddy covariance, EC) and physiological measurements (sap flow, SF) allows a better comprehension of the processes involving in the Soil–Plant–Atmosphere continuum. To this aim, an experimental dataset of actual evapotranspiration, plant transpiration, and soil water content measurements was collected in an olive orchard during the midseason phenological period of 2009 and 2010. It was demonstrated that the joint use of EC and SF techniques is effective to evaluate the components of actual evapotranspiration in an olive orchard characterized by sparse vegetation and a significant fraction of exposed bare soil. The availability of simultaneous soil water content measurements allowed to estimate the crop coefficients and to assess a simple crop water stress index, depending on actual transpiration that can be evaluated even in the absence of direct measurements of actual transpiration. The crop coefficients experimentally determined resulted very similar to those previously evaluated; in particular, in the absence of water stress, a seasonal average value of about 0.65 was obtained for the “single” crop coefficient, whereas values of a 0.34 and 0.41 were observed under limited water availability in the root zone. The comparison between the values of crop water stress index evaluated during the investigated periods evidenced systematically lower values (less crop water stress) in the first year compared to the second, according to the general trend of soil waters content in the root zone. Further researches are however necessary to extent the experimental dataset to periods characterized by values of soil evaporation higher than those observed, in order to verify the crop coefficients even under different conditions than those investigated.

Frequency domain reflectometry (FDR) downhole sensors have been increasingly used for soil moisture field monitoring because they allow measurement, even continuously, along a soil profile. Moreover, they can also be installed with minimal soil disturbance around the access tube. The objectives of the paper were to assess the field and laboratory calibration protocols for a FDR capacitance probe (Diviner 2000) for a range of soils characterized by different particle size distributions and shrink/swell potential and to propose a practical and effective protocol on the basis of undisturbed soil samples, accounting for soil shrinkage/swelling processes characterizing swelling clay soils. The experiments showed that on coarse-textured soils, field calibration under wet, moist, and dry conditions allows estimations of the volumetric soil water content, with root-mean-square error (RMSE) values always lower than 0.058 cm3 · cm-3. On the contrary, the problems occurring in the field on finer-textured soils, which are characterized by a clay content ranging between 36.7 and 45.1% and moderate to high shrink/swell potential, did not permit identification of suitable calibration equations and then accurate estimations of the soil water content. For such soils, in fact, a great dispersion of the experimental data and consequently high error values associated with the site-specific calibration equations, i.e., up to 0.121 cm3 · cm-3 for the soil characterized by the highest clay percentage, were observed. The laboratory experiments were carried out by using undisturbed soil monoliths which, compared with sieved soils, have the advantage of accounting for the natural soil structure surrounding the access tube and monitoring the soil shrinkage processes occurring in clay soils during sensor calibration experiments. The Diviner 2000 calibration equations obtained in the laboratory were characterized by error values generally lower than those obtained in the field and always smaller than 0.053 cm3 · cm-3. Finally, in the range of a soil water content between approximately 10% and the maximum observed, the scaled frequency measured by the sensor was almost constant at a decreasing soil water content. This circumstance can be ascribed to the normal phase of the shrinkage process determining the compensative effects between the reduction of the volumetric soil water content and the increasing soil bulk density. The maximum variations of scaled frequency were observed in the range of the soil water content, for which the resulting soil bulk density was approximately constant. The knowledge of the soil shrinkage characteristic curve therefore assumes a key role when calibrating FDR sensors on shrinking/swelling clay soils.

This paper compares two agro-hydrological models that are used to schedule irrigation of a typical Mediterranean crop. In particular, a comparison between the Food and Agriculture Organization (FAO) model, which uses a black box approach, and the soil-water-atmosphere-plant (SWAP) model, which is based on the numerical analysis of Richards' equation, are shown for wine grape. The comparison was carried out for the 2005 and 2006 irrigation seasons and focused on hydrological balance components and on soil water contents. Next, the ordinary scheduling parameters were identified so that the performance of the two models, which aimed to evaluate the seasonal water requirements and the irrigation times, could be assessed. In the validation phase, both of the models satisfactorily simulated the soil water content, and comparable values of cumulative evapotranspiration were obtained. With the goal of recognizing the crop water stress condition in the field, the original algorithm of the FAO model was modified. This research provided evidence of how the two agrohydrological models, although characterized by different approaches in modeling the phenomena, showed a similar behaviour when used for scheduling irrigation under soil water deficit conditions.

Summary A coupled energy/hydrologic model was applied to simulate the exchange of energy and water in the soil–plant-atmosphere system (SPA). The model, which uses a “two-source” approach to estimate the energy fluxes, and the “force-restore” approach to represent the water balance, was validated by means of evapotranspiration measurements collected via scintillometry and soil moisture measurements collected via time domain reflectometry (TDR) in a Sicilian olive grove. The comparison between measured and estimated fluxes values at an hourly scale showed good agreement. Additional comparisons on a daily timescale confirmed the model’s applicability for quantifying crop water requirements. Also in terms of daily evapotranspiration and soil water content values, the obtained results confirmed the model’s applicability for those practical applications aiming to quantify the crop water requirement. Moreover, further studies should be conducted to test the feasibility of using this model for long term simulations over a broad range of conditions.

Actual evapotranspiration from typical Mediterranean crops has been assessed in a Sicilian study area by using surface energy balance (SEB) and soil-water balance models. Both modelling approaches use remotely sensed data to estimate evapotranspiration fluxes in a spatially distributed way. The first approach exploits visible (VIS), near-infrared (NIR) and thermal (TIR) observations to solve the surface energy balance equation whereas the soil-water balance model uses only VIS-NIR data to detect the spatial variability of crop parameters. Considering that the study area is characterized by typical spatially sparse Mediterranean vegetation, i.e. olive, citrus and vineyards, alternating bare soil and canopy, we focused the attention on the main conceptual differences between one-source and two-sources energy balance models. Two different models have been tested: the widely used one-source SEBAL model, where soil and vegetation are considered as the sole source (mostly appropriate in the case of uniform vegetation coverage) and the two-sources TSEB model, where soil and vegetation components of the surface energy balance are treated separately. Actual evapotranspiration estimates by means of the two surface energy balance models have been compared vs. the outputs of the agro-hydrological SWAP model, which was applied in a spatially distributed way to simulate one-dimensional water flow in the soil-plant-atmosphere continuum. Remote sensing data in the VIS and NIR spectral ranges have been used to infer spatially distributed vegetation parameters needed to set up the upper boundary condition of SWAP. Actual evapotranspiration values obtained from the application of the soil water balance model SWAP have been considered as the reference to be used for energy balance models accuracy assessment. Airborne hyperspectral data acquired during a NERC (Natural Environment Research Council, UK) campaign in 2005 have been used. The results of this investigation seem to prove a slightly better agreement between SWAP and TSEB for some fields of the study area. Further investigations are programmed in order to confirm these indications.

The authors deal with the quite interesting and actual problem of Diviner 2000 capacitance probe calibration and present some field and laboratory data obtained on two different layers (0–0.26 and 0.26–0.50 cm) of the same soil profile, characterized by different textural class. The importance of site-specific calibration of sensors used to monitor soil or plant water status assumes a particular relevance in semiarid environments where the application of precision irrigation represents an appropriate management strategy aimed to achieve high values of water use efficiency (Cammalleri et al. 2013). Moreover, in clay soils, physical properties are strongly influenced by soil water content (Provenzano et al. 2013), so that the correct measurement of this variable plays a key role to increasing crop yield and preserving water. However, the discussers would focus on some significant points to be corrected in the manuscript and some others that should have been specified in the methodology and considered in the final discussion, as following specified, for the benefit of potential readers. The need to adequately install the access tube, aimed to ensure the contact between the tube and the surrounding soil, is not only to avoid preferential flow of water down the walls of the tube, as considered in the paper, but also to reduce the air gap around the tube and to avoid rough measurements of scaled frequency, used to estimate soil water contents, whose values depend on the mutual proportion of soil, water, and air in the soil volume investigated by the sensor. With reference to the second part of Eq. (2) of original paper, it is necessary to precise that the function θwðSFÞ correctly results

[EN] Agro-hydrological models are considered an economic and simple tool for quantifying crop water requirements. In the last two decades, agro-hydrological physically based models have been developed to simulate mass and energy exchange processes in the soil-plant-atmosphere system. Although very reliable, because of the high number of required variables, simplified models have been proposed to quantify crop water consumes. The main aim of this paper is to propose an amendment of the Food and Agricultural Organization (FAO) of the United Nations FAO-56 spreadsheet program to introduce a more realistic shape of the stress function, valid for mature olive orchards (Olea europaea L.). The modified model is successively validated by means of the comparison between measured and simulated soil water contents and actual transpiration fluxes. These outputs are finally compared with those obtained with the original version of the model. Experiments also allowed assessing the ability of simulated crop water stress coefficients to explain the actual water stress conditions evaluated on the basis of measured relative transpirations and midday stem water potentials. The results show that the modified model significantly improves the estimation of actual crop transpiration fluxes and soil water contents under soil water deficit conditions, according to the RMSEs associated with the revised model, resulting in significantly higher than the corresponding values obtained with the original version. (C) 2014 American Society of Civil Engineers.