Search

Although many commercial stabilizers are available for the treatment of poor soils; agricultural, agro-industrial, and environmentally friendly stabilizers are always encouraged. In this study, an attempt has been made to assess the effects of brewery spent grain ash (BSGA) on lime-treated clay for stabilization of an expansive clay to be used as road construction material. Brewery spent grain (BSG) is an agro-industrial solid waste product obtained during the brewing of beer. Through burning in an open cylinder, it is converted to BSGA. The clay was subjected to preliminary tests to classify and identify some required engineering properties of the sample. Initially, samples were thoroughly mixed with lime by weight of clay to determine the optimum amount of lime needed throughout the experiments. Through laboratory execution trials, 10% lime was determined to be the optimal amount. Following, BSGA was added to the treated clay, which was previously treated with 10% lime, at various percentages of 2, 4, 6, 8, and 10% BSGA by weight of clay. At 0% BSGA, the unsoaked and soaked California bearing ratio (CBR) rose from 13.56 and 8.24% to their greatest values of 14.99% and 9.3%, respectively, at 6% BSGA. Unconfined compressive strength (UCS) values rose from 112.63 kN/m2 at 0% BSGA to 130.31 kN/m2 at 6% BSGA, which is the highest value. Therefore, it was discovered that BSGA can be a beneficial addition to lime stabilization in clay soil. [ABSTRACT FROM AUTHOR]

Expansive clayey soils (CSs) expand and become softer as moisture content increases, but they get harder and stronger as they dry out. The earth's swelling and shrinkage characteristics under varying moisture conditions make roads built on expansive CS, in particular, vulnerable to early degradation. In this investigation, coffee husk ash (CHA), gypsum, and a blend of the two additives (G-CHA) were used in experimental tests to treat expansive CS. This study aims to evaluate experimentally the potential of expansive soil stabilization using different additives: CHA, gypsum, and a combination of gypsum and CHA. Five different percentages of CHA (5%, 10%, 15%, 20%, and 25%), three percentages of gypsum (3%, 6%, and 9%), and variable percentages of their combinations were used to stabilize the soil for pavement subgrade application. Atterberg limits, compaction, linear shrinkage (LS), swelling, unconfined compressive strength (UCS), and California bearing ratio (CBR) tests were performed on treated and virgin soil specimens at 3, 7, 14, 28, and 56-day curing times. Results showed that CHA additives effectively reduced the plasticity, LS, and swell potential in addition to increasing the maximum dry unit weight, UCS, and CBR. It was determined that the UCS and CBR values for the 6% stabilized gypsum soil increased by 28.95% and 19.54%, respectively, and reduced by 41% of the plastic index parameter after the addition of 15% CHA. Based on the evaluation of the results, an optimum mixture of 6% gypsum and 15% CHA (SG6C15) stabilized soil can be used in pavement subgrade applications as it achieved the minimum strength target. The performance of CHA-treated samples as subgrade material is superior to that of untreated virgin soil. Because of the stronger subgrade, smaller pavement layers result in a thinner pavement structure. [ABSTRACT FROM AUTHOR]

Expansive soils are extremely susceptible to swelling and shrinkage associated with seasonal changes in their moisture content. This can cause serious damage to structures constructed on expansive soils. Stabilization using additives is widely used to mitigate the concerns of expansive soils by controlling the changes in volume, thereby increasing the strength and durability of the soils. Multistabilizers, including a low percentage of conventional additives with nonconventional additives, can reduce the costs of stabilization. The performance of the stabilized soil can be enhanced by admixture optimization to ascertain that the agent's ratios are quite adequate to meet the optimal levels of modification. Unfortunately, despite the development of advanced techniques for investigating the stabilization of expansive soil, limited studies are devoted to the optimization of admixture to soils. Hence, in this research, an approach based on rough set theory, a mathematical data mining approach, is presented for multiagent optimization for efficient treatment of expansive soils. The multiadditives used in this study are almond shell ash (ASA), volcanic rock dust (VRD), and portland cement (PC). The differential free swell test, the California bearing ratio test, and the unconfined compressive strength test were applied for assessing the characteristics of the stabilized soil specimens. The obtained results and the confirmatory tests demonstrated that a combination of 20% ASA and 20% VRD with 8% PC provides the optimum results in the properties of expansive soil. The microstructural analysis denoted an enhanced modification of the soil engineering properties. The outcomes of this research confirm that the rough set optimization procedure is highly suitable for application in multiagent optimization for the efficient treatment of expansive soils. [ABSTRACT FROM AUTHOR]

The low bearing capacity of expansive soils often results in serviceability issues and premature failures of infrastructure built upon them. Various studies have demonstrated the use of different soil treatment methods using mechanical or chemical approaches to stabilize the weak ground as a precaution. Most of the reported studies are limited to either lab-based investigations or field monitoring works without the scientific connection between theory and translation. This study aims to verify the field application of a novel soil stabilization method by conducting laboratory-controlled experiments and field performance testing as verification. Enzyme–based soil stabilization was adopted for in-situ clay soil in combination with ordinary portland cement as a sustainable stabilization approach. Soil samples were collected at different regions from the field to evaluate the effectiveness and the mechanism of soil stabilization in the field by the means of replicating stabilization at the laboratory scale using identical mixing proportions of the additives. The mechanical behavior of stabilized soil was assessed through the unconfined compression strength and California bearing ratio test methods. In addition, the changes in the chemical composition of the soil due to the additives were evaluated through the X-ray diffraction testing technique and microporosity test using 2D images translated to 3D profiles from X-ray micro CT tomography. The efficacy of field stabilization was evaluated by conducting the falling weight deflectometer test in the stabilized site. Results from the study are useful to understand the efficacy of field soil stabilization and enhance the reliability of enzyme–based stabilization in practice. [ABSTRACT FROM AUTHOR]

This study investigated the different geotechnical characteristics of soil stabilization with the addition of lime and rice husk ash (RHA) in varying amounts (3%, 5%, 7%, and 9% lime, and 4%, 8%, 12%, and 16% RHA). A series of compaction, unconfined compressive strength (UCS), California bearing ratio (CBR), pH, and X-ray diffraction (XRD) tests were performed in the laboratory to assess the impact of the considered admixtures on the stabilized soil parameters. This study also proposes the successful integration of an artificial neural network (ANN) and a Gaussian process regression (GPR) with the experimental UCS observations. The lime concentration, RHA concentration, and curing period were considered as the input parameters, and UCS was considered as the response. The proposed framework was extended to analyze the compressive behavior of treated soil on the minuscule level. Such coupled machine learning-based experimental investigation can provide deep insight into the soil behavior which otherwise would have remained unexplored due to the prohibitive nature of performing laboratory experiments on a large scale. The findings demonstrated the effectiveness of RHA in addition to lime in stabilizing the considered expansive soil. With the addition of lime and RHA mix, the UCS and CBR values of the treated soil increased significantly. [ABSTRACT FROM AUTHOR]

The utilization of fly ash (FA) and powdered granulated steel slag (PGSS) as additives in soil stabilization plays a crucial role in environmental, economic, and weak soil property improving advantages. In this study, the combined effect of FA and PGSS in improving expansive subgrade soil was investigated. The materials used for this study were expansive soils, FA, and PGSS. The study has applied an experimental research method. For this investigation, the index properties, Free Swell Index (FSI), unconfined compressive strength (UCS), optimum moisture content (OMC), California bearing ratio (CBR), and scanning electron microscope (SEM) tests were done for treated and untreated expansive soils. The findings indicated that as the mixture of FA (0 to 12.5% at 5% increment) and PGSS (0 to 25% at 5% at 2.5% increment) is added to the untreated expansive soils, the index properties, FSI, and OMC of the soils were significantly declined. The CBR values of expansive soils containing 20% FA and 10% PGSS mixture were 13.8% and 16.21%, respectively, which improved the quality of the soils by 85.43% and 84.82%, respectively. While the untreated expansive soils have a UCS value of 0.34 kg/cm2, the treated soil comprising 20% FA and 10% PGSS mixture has a UCS value of 13.42 kg/cm2, indicating that the soil strength is enhanced by 97.47%. The results of the studies demonstrate that adding FA and PGSS to expansive soil improves its stability and strength. The study concluded that disposals such as FA and PGSS might be effectively used in enhancing the characteristics of construction materials and used for the construction. [ABSTRACT FROM AUTHOR]

This study investigated the feasibility of using agricultural wastes: sugarcane bagasse ash and plantain leaves ash for clay soil stabilization. The sample was mixed using five trial mixes: 0%BA:10%PLA, 3%BA:7%PLA, 5%BA:5%PLA, 7%BA :3%PLA, 10%BA:0%PLA and a control mix. Characterization of these ashes was done using the X-ray fluorescence testing method. Specific gravity, sieve analysis, Atterberg limits, compaction and California bearing ratio tests were also assessed. The clay soil was described as A-7-6 (AASHTO). After X-ray characterization, BA and PLA possessed 61.97% and 28.27% pozzolanic content respectively. From the liquid limit results, on addition of 3%BA :7%PLA, a significant decrease in values of 47.0%, 32.0% and 15.0% to 36.0%, 26.0% and 10.0% for LL, PL and PI was documented. Also, the addition of plantain leaves alone significantly decreases atterberg limit values. For compaction, 3%BA and 7%PLA recorded the least MDD value of 18.44kN/m³ and peak value of 19.42kN/m³ at 0%BA: 10%PLA. 10%PLA and 10%BA recorded CBR soaked values of 57.8% and 62.1% whilst 7%BA:3%PLA yielded best results of 51.3% CBR soaked values. These findings reveal significant improvements in strength and index properties of the clay soil. In conclusion, bagasse ash and plantain leaves ash produce an eco-friendly stabilizer that can be utilized as subbase material in the stabilization of clay soils. [ABSTRACT FROM AUTHOR]

This experimental study examines the efficacy of the inclusion of randomly distributed polypropylene fiber (PP) reinforcement on the engineering properties of expansive clays. The effect of PP fiber inclusions (0%-0.8%) on compaction, unconfined compressive strength (UCS), elastic modulus (E50), California bearing ratio (CBR) and swell-consolidation parameters of test soil were explored. Experimental results showed significant improvement in the strength parameters of treated soils with an optimal fiber content at about 0.4% by weight of soil. The swell-consolidation parameters were also observed to be significantly ameliorated in fiber-reinforced samples. Test results indicate that the use of PP fiber as a reinforced stabilizer for expansive clays not only benefits the sustainable utilization of fiber wastes in soil stabilization, but also reduces the environmental footprint globally. [ABSTRACT FROM AUTHOR]

Oil pollution causes deterioration of the physical, chemical, mechanical, and geotechnical characteristics of affected soil leading to loss of soil productivity for engineering purposes. Different stabilization methods serve as a remedy for such soil to regain its loss engineering properties. This study was concerned with the utilization of lime to stabilize crude oil contaminated soil and to investigate its efficacy for soil stabilization. The study also focused on determining the geotechnical properties of crude oil contamination and matching the result with standard specifications established for engineering works. Hydrated lime, expansive clayey soil, contaminated soil, and potable water were the materials used for the experimental investigation. The contaminated soil was treated with 6.5% lime and 0–20% crude oil contaminated materials obtained from oil exploration sites in North-Eastern Nigeria and per standard test method for laboratory evaluation of consistency limits, compaction properties, California bearing ratio (CBR), and microstructural and mineralogical assessments. The experimental results obtained were further tested statistically through one-way ANOVA and F-statistics to establish the source of variation for the geotechnical properties, while multiple linear regression and correlation statistics helped draw the connection between the consistency limits, compaction, and CBR properties of the soil-lime-COCM blend. Results indicated a coefficient of determination of 99.86. The contaminated soil materials were found to show optimal performance at a 5% ratio and 6.5% of lime for civil construction purposes. [ABSTRACT FROM AUTHOR]

Weak subgrade is the main problem facing most highway projects. Therefore, this study focuses on trying to improve the properties and increase the strength of weak, clayey, swelling soil for use as a subgrade for pavement structural sections. This trial was developed using a mix of granular and chemical stabilization for the soil. Granular stabilization was applied firstly by mixing natural sand at different percentages of 20%, 35%, and 50% of the total weight of clayey, swelling soil samples to find the minimum percentage that could be added to improve it to sandy, clayey soil, which is acceptable as a subgrade according to the Egyptian highway specification code. Secondly, chemical stabilization was applied to enhanced sandy, clayey soil to increase its strength properties. This was performed by adding chemical additives (lime, cement kiln dust (CKD), fiberglass, Addicrete 11, and gypsum) at different ratios of 2%, 4%, and 6% of the total weight of the samples of enhanced sandy, clayey soil. An experimental program was conducted consisting of characteristics and consistency tests, the California bearing ratio (CBR) test, a proctor test, and a consolidated-drained (C-D) tri-axial shear test. The results showed that 50% sand was the minimum percentage that could be mixed with swelling, clayey soil for granular stabilization to be enhanced and become sandy, clayey soil, which is accepted as a subgrade layer according to the Egyptian highway specification code. In addition, using a mix of granular and chemical stabilization increased the compressive strength of this enhanced subgrade by adding 6% lime or cement kiln dust (CKD) of the total sample weight. They enhanced the strength of the soil and reduced its plasticity. Adding 6% fiberglass and polymers could slightly enhance the desired properties; however, it is not recommended to use them due to their slight effect and economic cost. In addition, it is not recommended to use gypsum at more than 4% due to its negative effect on CBR. [ABSTRACT FROM AUTHOR]

Efficient utilization of problematic soils such as soft clay by imparting additional strength using various stabilization techniques is done to improve soil properties. The application of nanomaterials in the area of soil stabilization has great potential to create a stiff skeleton, especially when blended with cementitious materials. Using the response surface method, this study focused on studying the effects of single and blended cementitious systems, comprising cement (0% to 20%), slag (0% to 20%), and nanosilica (0% to 2.4%), on the properties of soft clay in wet conditions [water-to-soil ratio (w/s) of 53% to 87%]. The mechanical [California bearing ratio (CBR), unconfined compressive strength up to 91 days] and durability (freezing-thawing durability factor) properties of stabilized clay were investigated, and the bulk trends were corroborated by thermogravimetry and microscopy analyses. Based on statistical analysis, incremental addition of cement, slag, and nanosilica led to the systematic increase in the properties of soft clay, albeit to different extents and with different mechanisms. At the low w/s (53%), superior mechanical and durability properties were obtained for soft clay stabilized with the ternary binder comprising cement, slag, and nanosilica. Numerical optimization showed that stabilizing this weak type of soft/expansive clay is possible, but the results (proportions, performance, cost) varied based on the target design criteria and application. [ABSTRACT FROM AUTHOR]

Plastic clays in subgrade may cause major engineering defects such as excessive heave or settlement during the wet season that contribute to the formation of uneven geometry at the pavement surface. Soil stabilization is often a requisite to ameliorate the engineering properties of soft soils or reactive clays. This study investigates the application of nano-silica and nano-alumina to improve the California bearing ratio (CBR) of a local clay. The clay was treated with cement (2%–8%), with nano-additive (0.1%–1.5%) and with cement and nano-additive (3% cement + 0.1%–1.5% nano-additive). The compacted sample was cured for 7 days and subjected to soaked and unsoaked CBR tests. The soaked CBR of the nontreated clay increased by 49% and 27% for 1% nano-silica and 1% nano-alumina treated clay, respectively. Although 3% cement addition improved the CBR of the soaked clay by 28%, the combination of 3% cement with 1% nano-silica and nano-alumina resulted in 196% and 164% increase in the soaked CBR of the nontreated clay, respectively. The combination of nano-additives and cement yielded the same soaked CBR as if 6%–7% cement would have been used. Clay treated with 1% nano-silica and 3% cement achieved the highest CBR value within the tested samples and the sample treated with 1% nano-alumina and 3% cement achieved the lowest free swell potential. The scanning electron microscopy (SEM) micrographs of the treated clay showed the formation of uniform fabric with fewer pore spaces and calcium silicate hydrate (CSH)/calcium aluminate hydrate (CAH) products within the fabric of nano-additive treated clay. [ABSTRACT FROM AUTHOR]

The study showcase the optimization of California bearing ratio (CBR) values of expansive soil treated with cement kiln dust (CKD) and metakaolin (MTK) blend based on Scheffe optimization method. The CBR values utilized in the design of road infrastructure is an important parameter because it provides the rating of soil material for use as subgrade, sub-base and/or base course of road pavement. Therefore, applying Scheffe optimization technique will eliminate the random selection of design mix ratios and other associated disadvantages during CBR tests. Based on the optimization exercise and it results, the maximum CBR (unsoaked and soaked) values of 69 and 50 % were achieved with a corresponding mix ratio of 1.0:0.30:0.35:0.50 for black cotton soil, water, cement kiln dust and metakaolin respectively. During the course of this study, the laboratory results were used to develop two CBR models. The scheffe models developed are Ŷ=34X1+46X2+40X3+69X4-8X1X2-4X1X3+34X1X4+8X2X3+34X2X4+30X3X4 and Ŷ=17X1+28X2+22X3+50X4-10X1X2-6X1X3+42X1X4+8X2X3+40X2X4+40X3X4 for CBR unsoaked and soaked, respectively. In addition, the mathematical models were statistically scrutinized, confirmed for the adequacy and validity based on the outcomes of student t-test and analysis of variance (ANOVA). Also, the scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) techniques were used to explore the morphological and composition variations of the natural soil in contrast with the typically optimized soil-CKD-MTK blend. However, the SEM of the unaltered soil sample showed a smooth like surface, whereas the soil mixture optimally treated does not show same but rather demonstrated a rough like surfaced morphology. Thus, the observed variations might be due to the alterations of the soil fabrics possibly enhanced by the development of cementitious compounds (calcium silicate hydrate and calcium aluminate hydrate) as a result of pozzolanic reaction. [ABSTRACT FROM AUTHOR]

This research investigates the microstructural and geotechnical properties, environmental impact, and economic benefit of cement kiln dust (CKD)-treated kaolinite clay with the addition of sodium chloride (NaCl). As a chemical admixture, NaCl is expected to enhance the strength properties of the clay soil stabilized by CKD. To verify this issue, the geotechnical characteristics of CKD-treated soils with different contents of NaCl (2.5, 5, and 10%) were examined. To this end, the Atterberg limits, standard Proctor, unconfined compressive strength and California bearing ratio (CBR) tests were conducted. Besides, scanning electron microscopy (SEM) analysis was used to observe the microstructural changes resulting from using additives. It was found that the addition of NaCl to the CKD-stabilized clay caused the maximum dry density to increase and the optimum moisture content to decrease. 10% NaCl enhanced the unconfined compressive strength of the CKD-treated soil to 18.7% and 8% higher than that of the NaCl-free specimen during 7 and 28 days of curing, respectively. These results were in accordance with the consequences extracted from the CBR behavior diagram. Moreover, cementitious compounds products in the mixtures were presumed to be the significant factor contributing to strength improvements based on the SEM results. The stabilized clayey soil with 15% CKD and 10% NaCl as environment-friendly method could significantly reduce energy consumption, e-CO2 emission, and cost of soil stabilization. [ABSTRACT FROM AUTHOR]

This paper presents a laboratory investigation on the use of construction demolition waste in poor clayey soil to improve its strength and drainage characteristics. Various laboratory tests such as differential free swell, Atterberg's limits, compaction, unconfined compressive strength (UCS), California bearing ratio (CBR), and permeability have been conducted on un-stabilized and Construction Demolition Waste (CDW) stabilized clayey soil. The outcomes revealed that the addition of CDW in poor soil reduced both maximum dry density and optimum moisture content. The UCS, CBR, and permeability got improved on adding optimum content of CDW in poor clayey soil. The secant modulus also increased on addition of the CDW in virgin soil. The regression analysis performed for different tests showed good agreement of laboratory results with predicted values. Thus, it can be revealed that using CDW in stabilization of poor clayey soil will not only solve the problem of its disposal but will also be cost effective and protect the environment. [ABSTRACT FROM AUTHOR]

[Display omitted] • The incorporation of nanoclay and rice plant fibers improves the mechanical properties of clay soils. • As a reinforcement, rice fibers increase the interlocking and binding of soil particles, while nanoclay's viscous gel increases cohesion. • Rice plant fiber is a highly renewable and eco-friendly material that can be an alternative to traditional stabilizers when combined with nanoclay as a natural material. Conventional stabilizers such as cement and lime are extensively used to improve the mechanical properties of soils. However, these materials suffer from geo-environmental concerns, especially greenhouse gas emissions. In this respect, incorporating sustainable and renewable materials into the soil is an effective technique to enhance its mechanical properties. This study investigated the effect of rice fibers (as a low-cost and eco-friendly material) and nanoclay on soil's mechanism and mechanical performance. In this study, pure soil samples and three nanoclay dosages (0.4, 0.8, and 1%) and three rice fiber ratios (0.3, 0.6, and 0.9%) in three lengths of 5, 10, and 15 mm in random distribution were tested. The prepared samples were characterized through compaction, unconfined compressive strength (UCS), direct shear strength, tensile strength, California bearing ratio (CBR), and scanning electron microscopy (SEM) examinations. First, the optimum amount of nanoclay was determined based on the compressive strength test. Then, the effect of optimum nanoclay and randomly distributed rice fibers was investigated on the mechanical properties of stabilized soil. The results showed that the shear and compressive strengths of the reinforced soil were higher than those of the control samples. An increase in the dosage of rice fibers improved the failure strain, soil ductility, and shear strength. The optimum amount of fibers was 0.9%, exceeding which led to fiber twisting and agglomeration. However, increasing the nanoclay content decreased the failure strain. According to the microscopic examination, when fibers were combined with nanoclay, the interaction between soil particles and fibers increased due to the filling property and the formation of a viscous gel. Overall, fiber added with nanoclay improved the mechanical properties of clay soil and could be used as a low-cost and sustainable option for soil improvement. [ABSTRACT FROM AUTHOR]

Applying synthetic fibers is one of the most effective physical methods for soil improvement and stabilization. In this paper, we determine the effects of polypropylene (PP) and poly vinyl alcohol (PVA) fibers contents (0.2, 0.5, 1.0 and 1.5%) at environment temperature (25 °C) and various freezing soil temperatures (0, −5, −10 and − 15 °C) on stabilization of the clayey sand soil (SC) samples. The results show that for both types of fibers, by simultaneous increasing of fiber content and lowering the temperature, the values of the unconfined compressive strength (UCS), elastic modulus (EM), ductility and California bearing ratio (CBR) increase, and they all reach their maximum values for 1.5% fiber content at −15 °C. Moreover, we show that PVA fibers perform better compared to PP fibers in increasing of UCS, EM, ductility and CBR values for different fiber contents and temperatures. This can be attributed to the fact that PVA has higher tensile and flexural strength compared to PP fiber. • The effect of freezing soil temperatures (FSTs) on strength parameters of a clayey sand (SC) soil stabilized by poly propylene (PP) and poly vinyl alcohol (PVA) fibers is investigated. • For both types of PP and PVA fibers, by simultaneous increasing of fiber content and lowering the temperature (FSTs effect), the strength parameters of SC soil samples are increased. • The strength parameters of SC soil samples reinforced by PP and PVA fibers reach their maximum values for 1.5% fiber content at −15 °C. • The PVA fibers perform better compared to PP fibers in increasing of strength parameters for different fiber contents at environment temperature and FSTs. [ABSTRACT FROM AUTHOR]

• In this study, different types of green cement-free soil stabilizers are proposed. • CKD outperforms cement based on enhancing kaolinite clay soil strength properties. • Silica fume and nano-silica are considered stabilization's activators. • Replacing cement with CKD significantly reduces environmental pollutions. • Nano-silica should not be applied more than 1% in clayey soil stabilization. This investigation aims to assess the nano-silica and silica fume effectiveness on engineering clay soils' characteristics stabilized with cement kiln dust. Laboratory tests, including Atterberg limits, standard Proctor compaction, unconfined compressive strength, and California bearing ratio, were performed. The manufactured specimens were tested 7 and 28 days after preparation to analyze the curing time impacts on soil's strength characteristics. Meanwhile, changes in the chemical and microstructures of soil were observed using scanning electron microscope examination and X-ray diffraction analysis. Subsequently, the mixtures were compared based on eight environmental parameters. To this end, a new environmental index was developed to consider all environmental criteria simultaneously. Afterward, three criteria, including 28-day unconfined compressive strength, environmental index, and unit price, were taken into account as sustainability criteria. Moreover, the gray relational analysis was employed to examine the mixtures' sustainability. The results demonstrated that the amount of 1% nano-silica and 15% silica fume by dry soil weight was an optimum addition content of employed activators for enhancing the CKD-treated soil's geotechnical properties, respectively. Furthermore, the sustainability evaluation revealed that CKD-treated soil was the most sustainable mixture. Given the sustainability effects, nano-silica addition less than 2% and silica fume to the CKD-stabilized soil can lead to propose treated soil with considerably more sustainability than cement. It is essential to highlight that the sustainability of CKD-treated soils containing silica fume was considerably more than that of stabilized soils comprising nano-silica. [ABSTRACT FROM AUTHOR]

In the search for alternatives to bioremediation of soils, this research aimed to analyze the effects of lime, cement, and asphalt as stabilizers on clayey gravel and sand soil contaminated with gasoline in the laboratory. Concentrations of 10–20% of lime, cement, and asphalt were added to the soil. A standard sample was chosen to compare the results obtained in the modified Proctor compaction, California bearing ratio (CBR), direct shear, and consolidation tests. It was found that the presence of more than 10% liquid low–density hydrocarbon affects plasticity, void ratio, friction angle, moisture content, dry density, and cohesion. According to the tests carried out, soils contaminated with concentrations lower than 10% of gasoline are recommended to construct the subgrade and sub-base layers in pavements. Finally, it was found that cement is the stabilizer that presented overall higher enhancements of the mechanical properties of the clayey gravel and sand soil among the three stabilizers. However, the results also show that depending on the soil use and specific parameter requirements, other stabilizers can be used. [ABSTRACT FROM AUTHOR]

The waste glass is one of the huge volume construction and demolition (C&D) debris and using it in the construction, significantly reduces the area required for the storage and contributes to the conservation of natural resources while reducing the carbon footprint. In the light of these data, the answer to the question of whether glass powder could be considered as a stabilizing additive with sea water in lime-stabilized clayey soil so that clayey soil could be used in road pavement and embankment construction has been investigated. A series of experimental studies conducted to determine the effect of additives on the geotechnical properties of the clayey soil such as moisture-density relationships, strength, and consistency. The samples were prepared by blending 5% lime and different percentages of powdered glass such as 10%, 20% and 25% with three different clayey soil that were used as subgrade soil. The results of the tests indicate that powdered glass, sea water and clayey soils are very compatible to react with each other and additives improve geotechnical properties of clayey soils in a way so that it decreases plasticity index and increases workability of clayey soils. In addition, the additives increase California bearing ratio and unconfined compressive strength of clayey soils up to ten times depending on usage rates. [ABSTRACT FROM AUTHOR]