Search

Original multiscale flaked silver SERS-substrate (MFSS substrate) was applied for glycated albumin (GA) biosensing. The substrate is composed from silver flakes that have three orders of magnitude size dispersion: from 50 nm to 2 μm. The multiscale silver structure refracts the incident light and various surface plasmons are excited. Some of the internal plasmons are localized and give rise of the large local electric field. It was demonstrated that Raman scattering signal strongly depends: a) on "hot spots" formation at the edges and points of contact of silver plates, and b) on the angle of incidence. As a result the silver structure operates as an effective SERS substrate. To achieve the selectivity to glycated part, the surface of SERS-substrate was modified with 4-mercaptophenylboronic acid (4-mPBA). Various saccharides (Fru, Glc, Suc, Dex) were taken as model compounds for the glycated proteins determination. The saccharides contain cis-diol groups that form five- or six-membered ethers with boronic acid. Spectrum of SERS-substrate changes after sugar/glycated albumin treatment. Main differences in the SERS-spectra of sugar/glycated albumin treated SERS-substrate and control are referred to phenylboronic acid vibrations (999, 1021, 1072 and 1589 cm -1 ). Principal component analysis (PCA) and Partial Least Squares Regression (PLS-R) were used to discriminate spectra and to construct calibration curve, as well as to measure GA values in real samples of human plasma. Multiscale flaked silver SERS-substrate modified with 4-mPBA allows quantitative one-step biosensing of glycated albumin in 15 μl of human plasma., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2019 Elsevier B.V. All rights reserved.)

We perform a detailed investigation of coatings made of poly(p-xylylene) nanocomposites with embedded silver nanoparticles of sizes up to 12 nm and concentration up to 10.5 vol. %. We study their microstructure, mechanical, optical, and radiative characteristics. We reveal certain correlations between structural peculiarities and optical, as well as radiative properties. These correlations are due to fluctuations in distribution of nanoparticles in a polymer matrix and also due to the peculiarities of nanoparticles size distribution. We calculated optical dispersion coefficients for nanocomposites with different silver content. It was shown the refractive index ( n) and extinction coefficient (k) is strongly dependent on the silver content and change within the 1.4–2.4 for n and 0–0.6 for the k. It is argued that poly(p-xylylene)silver nanocomposites can be used to construct multilayer coatings with required optical constant and conformal to any complex morphology. [ABSTRACT FROM PUBLISHER]

Silver and gold are the most commonly used materials in optics and plasmonics. Silver has the lowest optical losses in the visible and near-infrared wavelength range, but it faces a serious problem—degradation over time. It has been repeatedly reported that the optical properties of silver thin films rapidly degrade when exposed to the atmosphere. This phenomenon was described by various mechanisms: rapid silver oxidation, sorption of sulfur or oxygen, formation of silver compounds with chlorine, sulfur, and oxygen. In this work, we systematically studied single-crystalline silver films from 25 to 70 nm thicknesses for almost two years. The surface morphology, crystalline structure and optical characteristics of the silver films were measured using spectroscopic ellipsometry, ultra-high-resolution scanning electron microscopy, and stylus profilometry under standard laboratory conditions. After 19 months, bulk structures appeared on the surface of thin films. These structures are associated with relaxation of internal stresses combined with dewetting. Single-crystalline silver films deposited using the single-crystalline continuous ultra-smooth, low-loss, low-cost (SCULL) technology with a thickness of 35–50 nm demonstrated the best stability in terms of degradation. We have shown that the number of defects (grain boundaries and joints of terraces) is one of the key factors that influence the degradation intensity of silver films. [ABSTRACT FROM AUTHOR]