Search

Compared to conventionnal bench top instruments, on-line GC analyzers require specific characteristics. On one hand, for some applications operating with a reactor pressure as high as several tens of bars, sample pressure has to be reduced before GC separation, or specific valves and columns have to be designed to perform separation with high carrier gas inlet pressure. On the other hand, informative detectors such as mass spectrometer are valuable but low maintenance detectors are prefered. To fit these two requirements (sampling at high pressure without decompression stage, and informative detector with low maintenance), short monolithic silica capillary column operated with inlet pressure as high as 60 bar has been hyphenated to VUV detector. Injection and column performance have been first investigated. The system has been optimized by adjusting split ratio at high pressure and by tuning two main VUV detector parameters ("average number" linked to data point averaging and make-up gas pressure) to decrease the limit of quantification. The optimization stage led to a set of experimental parameters which is a good compromise between signal-to-noise ratio and chromatographic efficiency. Finally, the hyphenated monolithic column has be used to partially separate a mixture of methane, ethane, carbon monoxide and carbon dioxide within 15 s, and the VUV deconvolution capabilities have been exploited to overcome coelution and finally separate individual signals., (Copyright © 2019 Elsevier B.V. All rights reserved.)

80% vinyltrimethoxysilane-based hybrid silica monoliths (80-VTMS), which have been initially developed for separation in reversed-phase liquid chromatography, have been investigated in high pressure gas chromatography separations (carrier gas pressure up to 60bar) and compared to silica monolithic columns. The behavior of both silica and 80-VTMS monolithic columns was investigated using helium, nitrogen and carbon dioxide as carrier gas. The efficiency of 80-VTMS monolithic columns was shown to vary differently than silica monolithic columns according to the temperature and the carrier gas used. Carrier gas nature was a significant parameter on the retention for both silica and vinyl columns in relation to its adsorption onto the stationary phase in such high pressure conditions. The comparison of retention and selectivity between 80-VTMS monoliths and silica was performed under helium using the logarithm of the retention factor according to the number of carbon atoms combined to Kovats indexes. The very good performances of these columns were demonstrated, allowing the separation of 8 compounds in less than 1min., (Copyright © 2017 Elsevier B.V. All rights reserved.)

In order to analyze light hydrocarbons mixtures with silica monolithic columns, a conventional gas chromatograph was modified to work with carrier gas pressure as high as 60bar. To understand hydrodynamic flow and retention with short columns (less than 30cm), special attention was required due to the temperature difference between the oven area and the FID detector which contain a significant length of the column. Efficiency and selectivity using various carrier gases (helium, nitrogen and carbon dioxide) at different inlet pressure for different oven temperature were studied. Carrier gas nature was a very significant parameter: on one side, linked to adsorption mechanism for gases like nitrogen and carbon dioxide onto the stationary phase modifying retention and selectivity, on the other side in relation to the minimum theoretical plate height which was as low as 15μm (66 000 platem(-1)) using carbon dioxide as carrier gas. The chromatographic system was then used to separate methane, ethane, ethylene, acetylene, propane, cyclopropane, and butane in less than 30s., (Copyright © 2016 Elsevier B.V. All rights reserved.)

This paper presents a photografting process of monolithic silica capillary columns based on the ene-thiol click chemistry. This study is performed on a "generic" vinyl-functionalized silica monolith (Hmin 6±1μm). The photoclick reaction is investigated using different thiol monomers (octadecanethiol, cysteine and sodium mercaptoethanesulfonate) to prepare capillary columns dedicated to various chromatographic modes (reversed-phase, HILIC and strong cation exchange). Whatever the monomer used, the photografting reaction is achieved in less than 5min with a relatively high thiol monomer content. This allows preparing highly retentive and efficient monolithic columns while avoiding polymerization and/or column clogging. In addition to the aforementioned properties (duration, versatility, efficiency), this photo-triggered chemical reaction allows addressing several appropriate surface functionalizations inside a single monolithic column in order to prepare nanovolume multimodal capillary columns. A multimodal biphasic monolithic column with a 1cm length cation-exchange segment followed by a 9cm length reversed-phase segment (SCX-RP) is prepared through two successive photografting reactions using a UV-mask to localize the reactions. This multimodal biphasic column is investigated using a model sample for the selective fractionation and separation of cationic and neutral compounds and is applied to the on-line preconcentration and separation of β-blockers., (Copyright © 2014 Elsevier B.V. All rights reserved.)

Herein, we report the "ene-thiol" photografting of 1-octadecanethiol onto vinyl pre-functionalized silica monolith to prepare clicked reversed-phase silica monolithic columns with high permeability and performances. The experimental conditions (concentration of thiol in solution, irradiation duration) are optimized with respect to highest retention and methylene selectivity, i.e. to the highest surface coverage of the monolith. It is demonstrated that an irradiation duration of 5min is enough with a 0.8M concentration of 1-octadecanethiol in solution or that it may be replaced by successive irradiations at a lower ODT concentration (0.19M) with renewing of the solution between the illuminations. Retention factors as high as those obtained with standard silanization are reached while keeping the intrinsic monolith permeability and efficiency (160,000plates/m in nano-LC at 0.7mm/s). The absence of polymerization, in the "ene-thiol" version, is demonstrated. Indeed, the steric selectivity of our clicked-material is characteristic of monolayer-like functionalized silica and significantly lower than the steric selectivity measured on polymeric-like functionalized silica., (Copyright © 2014 Elsevier B.V. All rights reserved.)

A simple, rapid and localizable photochemical process for the preparation of hydrophilic coated capillary and silica-based monolithic capillary columns is described. The process involves the free radical polymerization of acrylamide monomers onto acrylate pre-activated silica surface triggered by UV photoinitiation. The experimental conditions (monomer content, time of irradiation) were optimized on silica monolithic columns by monitoring the evolution of the chromatographic properties (retention, permeability, efficiency) in HILIC mode using a set of nucleosides as test solutes. Compared to thermal polymerization process, the photoinitiation allows the preparation of highly retentive and efficient HILIC monolithic columns in less than 10min of irradiation. This process was then successfully applied to the surface coating of fused silica capillary walls. In addition to its relative high stability and ability to reduce the electroosmotic flow, this polyacrylamide coating is localizable. Benefits of this localizable photochemical process are highlighted through the conception of an in-line integrated bimodal microseparation tool combining a SPE preconcentration step on a photografted silica monolith and an electrokinetic separation step in a polyacrylamide photopolymerized capillary section. Two neuropeptides are used as model solutes to illustrate the suitability of this approach., (Copyright © 2013 Elsevier B.V. All rights reserved.)

The thermodynamics of a chemical reaction confined at a solid surface was investigated through kinetic measurements of a model unimolecular reaction. The thermal cleavage of ester groups grafted at the surface of solid silica was investigated together with complementary physicochemical characterization of the grafted species. The ester molecules were chemically grafted to the silica surface and subsequently cleaved into the carboxylic acids. A grafting process of a reproducible monolayer was designed using the reaction of monofunctional organosilane from its gas phase. The thermal deprotection step of the ester end-group was investigated. The thermal deprotection reaction behaves in quite a specific manner when it is conducted at a surface in a grafted layer. Different organosilane molecules terminated by methyl, isopropyl and tert-butyl ester groups were grafted to silica surface; such functionalized materials were characterized by elemental analysis, IR and NMR spectroscopy, and thermogravimetric analysis, and the thermodynamic parameters of the thermal elimination reaction at the surface were measured. The limiting factor of such thermal ester cleavage reaction is the thermal stability of grafted ester group according to the temperature order: tert-butyl < i-propyl < methyl. Methyl ester groups were not selectively cleaved by temperature. The thermal deprotection of i-propyl ester groups took place at a temperature close to the thermal degradation of the organofunctional tail of the silane. The low thermolysis temperature of the grafted tert-butyl esters allowed their selective cleavage. There is a definite influence of the surface on the reaction. The enthalpy of activation is lower than in the gas phase because of the polarity of the reaction site. The major contribution is entropic; the negative entropy of activation comes from lateral interactions with the neighbor grafted molecules because of the high grafting density. Such reaction is an original strategy to functionalize the silica surface by carboxylic acid groups by means of a simple, reproducible, and efficient process involving in situ thermolysis of ester groups., (© 2011 American Chemical Society)

This paper presents a comprehensive theory and experimental characterisation of the modulation of the fluorescence intensity by the construction of optical interferences on oxidised silicon substrates used for DNA microarrays. The model predicts a 90-fold variation of the fluorescence signal depending on the oxide thickness. For a Cy3 dye, the signal is maximal for a 90 nm oxide thickness corresponding to a 7.5-fold enhancement with respect to a standard glass substrate. For experimental validation of the model, we have prepared Si/SiO2 substrates with different parallel steps of decreasing oxide thicknesses on the same sample using a buffered oxide etch (BOE) etching process after thermal oxidation. The SiO2 surface has been functionalized by a silane monolayer before in situ synthesis of L185 oligonucleotide probes. After hybridisation with complementary targets, the variations of the fluorescence intensity versus oxide thickness are in very good accordance with the theoretical model. The experimental comparison against a glass substrate shows a 10-fold enhancement of the detection sensitivity. Our results demonstrate that a Si/SiO2 substrate is an attractive alternative to standard glass slides for the realisation of fluorescence DNA microarrays whenever detection sensitivity is an important issue.