Search

Sulphur Emission Control Areas (SECAs), mandated by the International Maritime Organization (IMO), regulate fuel sulphur content (FSC) to mitigate the environmental and health impact of shipping emissions in coastal areas. Currently, FSC is limited to 0.1% (w/w) within and 0.5% (w/w) outside SECAs, with exceptions for ships employing wet sulphur scrubbers. These scrubbers enable vessels using non-compliant fuels such as high-sulphur heavy fuel oils (HFOs) to enter SECAs. However, while sulphur reduction via scrubbers is effective, their efficiency in capturing other potentially harmful gases remains uncertain. Moreover, emerging compliant fuels like highly aromatic fuels or low-sulphur blends lack characterisation and may pose risks. Over three years, we assessed emissions from an experimental marine engine at 25% and 75% load, representative of manoeuvring and cruising, respectively. First, characterizing emissions from five different compliant and non-compliant fuels (marine gas oil MGO, hydro-treated vegetable oil HVO, high-, low- and ultra-low sulphur HFOs), we calculated emission factors (EF). Then, the wet scrubber gas-phase capture efficiency was measured using compliant and non-compliant HFOs. NO x EF varied among fuels (5200-19700 mg/kWh), with limited scrubber reduction. CO (EF 750-13700 mg/kWh) and hydrocarbons (HC; EF 122-1851 mg/kWh) showed also insufficient abatement. Carcinogenic benzene was notably higher at 25% load and about an order of magnitude higher with HFOs compared to MGO and HVO, with no observed scrubber reduction. In contrast, carbonyls such as carcinogenic formaldehyde and acetaldehyde, acting as ozone precursors, were effectively scrubbed due to their polarity and water solubility. The ozone formation potential (OFP) of all fuels was examined. Significant EF differences between fuels and engine loads were observed, with the wet scrubber providing limited or no reduction of gaseous emissions. We suggest enhanced regulations and emission abatements in the marine sector to mitigate gaseous pollutants harmful to human health and the environment., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Inc. All rights reserved.)

The arise of autonomous ships has necessitated the development of new risk assessment techniques and methods. This study proposes a new framework for navigational risk assessment of remotely controlled Maritime Autonomous Surface Ships (MASS). This framework establishes a set of risk influencing factors affecting safety of navigation of a remotely-controlled MASS. Next, model parameters are defined based on the risk factors, and the model structure is developed using Bayesian Networks. To this end, an extensive literature survey is conducted, enhanced with the domain knowledge elicited from the experts and improved by the experimental data obtained during representative MASS model trials carried out in an inland river. Conditional Probability Tables are generated using a new function employing expert feedback regarding Interval Type 2 Fuzzy Sets. The developed Bayesian model yields the expected utilities results representing an accident's probability and consequence, with the results visualized on a dedicated diagram. Finally, the developed risk assessment model is validated by conducting three axiom tests, extreme scenarios analysis, and sensitivity analysis. Navigational environment, natural environment, traffic complexity, and shore-ship collaboration performance are critical from the probability and consequence perspective for inland navigational accidents to a remotely controlled MASS. Lastly, important nodes to Shore-Ship collaboration performance include autonomy of target ships, cyber risk, and transition from other remote control centers., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

With their complex structure, multiple failure modes and lack of maintenance crew, the safety problem of Maritime Autonomous Surface Ships' (MASS) machinery systems are becoming an important research topic. The present study presents an availability model for ship machinery systems incorporating a maintenance strategy based on Dynamic Bayesian Networks (DBN). First, the availability of conventional ship machinery systems is evaluated and used as a benchmark based on the configuration and planned maintenance strategy. Secondly, the availability of MASS machinery systems is compared to the benchmark, before the introduction of any changes to the ship's configuration and planned maintenance strategy. Finally, the availability improvement strategies, including redundant designs and planned maintenance strategies at port, are proposed based on sensitivity analysis and planned maintenance cost minimization. To exemplify the model's application, a case study of a cooling water system is explored. Based on a sensitivity analysis using the model, it is possible to decide which components need to be redundant. Different redundancy designs and corresponding planned maintenance strategies can be adopted to meet the availability demand. It is also shown that redundancy and enhanced detection capabilities reduce much of the planned maintenance cost. This framework can be used in the early design stages to determine whether the MASS machinery systems' availability is at least equivalent to that of conventional ships, and has certain reference significance for redundant configuration designs and MASS planned maintenance strategy schedule., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Humic-like substances (HULIS), known for their substantial impact on the atmosphere, are identified in marine diesel engine emissions obtained from five different fuels at two engine loads simulating real world scenarios as well as the application of wet sulfur scrubbers. The HULIS chemical composition is characterized by electrospray ionization (ESI) ultrahigh resolution mass spectrometry and shown to contain partially oxidized alkylated polycyclic aromatic compounds as well as partially oxidized aliphatic compounds, both including abundant nitrogen- and sulfur-containing species, and clearly different to HULIS emitted from biomass burning. Fuel properties such as sulfur content and aromaticity as well as the fuel combustion efficiency and engine mode are reflected in the observed HULIS composition. When the marine diesel engine is operated below the optimum engine settings, e.g., during maneuvering in harbors, HULIS-C emission factors are increased (262-893 mg kg -1 ), and a higher number of HULIS with a shift toward lower degree of oxidation and higher aromaticity is detected. Additionally, more aromatic and aliphatic CHOS compounds in HULIS were detected, especially for high-sulfur fuel combustion. The application of wet sulfur scrubbers decreased the HULIS-C emission factors by 4-49% but also led to the formation of new HULIS compounds. Overall, our results suggest the consideration of marine diesel engines as a relevant regional source of HULIS emissions.

Ships in service feature surfaces that exhibit biofouling, which alters the hydrodynamics of the vessels, thus affecting their normal displacement and significantly increasing their fuel consumption. The application of three types of ceramic coatings as ecological, effective and durable alternatives to commercial silicone-based marine coatings is investigated in this study. Three different ceramic glazes and two control commercial paints are analysed in an actual environment during 20 months of exposure to simulate the navigation conditions such that growth and roughness data can be obtained and then applied to computational fluid dynamics (CFD) software using an open-source Reynolds-averaged Navier-Stokes solver. The CFD results are validated under smooth hull conditions with a full-scale Kriso Container Ship (KCS) model and with different levels of hull roughness. The developed approach shows that the drag in hulls coated with conventional paint is 19% greater than that in hulls with ceramic coating.

The identification of ships plays a crucial role in security and managing vessel traffic for ports and onshore facilities. Existing video monitoring systems help visually identify a vessel where other systems are not present or sufficient. Readable vessel plates and hull inscriptions of detected ships in the video stream allow using text location and recognition methods to obtain ships' identification names or numbers. The obtained information can be then matched with available ship registers. The automation of the process has met many challenges related to the often-low quality of available video streams, heterogeneous regulations on the marking of ships, and the specifics of natural scene text recognition, such as quickly alternating imaging conditions or the interference of the background. The main contribution of this research is a method that can identify any type of vessel in an image that has visible inscriptions (name, registration number) placed on the hull and must be registered in a public registry. The proposed method works with low-quality images with inscriptions placed under different angles and different, readable sizes. Our method recognised 91% of vessels from our test dataset. Obtained identification times have not exceeded 1s. The quality and efficiency of the proposed solution indicate that it is suitable for practical implementation in onshore monitoring systems., Competing Interests: The authors have declared that no competing interests exist.

Riverside monitoring systems are used for controlling the passage of ships, counting them to prevent overcrowding in a port, or raising an alarm if the ship is unknown or not safe. This type of control and analysis is commonly carried out by many people who supervise CCTV in real time. In this paper, we present an alternative approach to automatic image analysis using a variety of artificial intelligence techniques. Based on collaborative learning, these are punished if they make an incorrect classification. The main advantage is the possibility of continually increasing the amount of knowledge during system operation. However, overtraining is possible, so each time, the best classifier is chosen. Another advantage for practical use is the small database, which allows for the quick and practical implementation of such a system. To verify its effectiveness, this ship classification system was tested on data obtained in a Polish city, Szczecin, as part of a bigger project for classifying inland ships and publicly available databases (for more general ship problems)., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2021 ISA. Published by Elsevier Ltd. All rights reserved.)

Improving the robustness of maritime emission inventories is important to ensure we fully understand the point of embarkment for transformation pathways of the sector toward the 1.5 and 2°C targets. A bottom-up assessment of emissions of greenhouse gases and aerosols from the maritime sector is presented, accounting for the emissions from fuel production and processing, resulting in a complete "well-to-wake" geospatial inventory. This high-resolution inventory is developed through the use of the state-of-the-art data-driven MariTEAM model, which combines ship technical specifications, ship location data, and historical weather data. The CO 2 emissions for 2017 amount to 943 million tonnes, which is 11% lower than the fourth International Maritime Organization's greenhouse gas study for the same year, while larger discrepancies have been found across ship segments. If fuel production is accounted for when developing shipping inventories, total CO 2 emissions reported could increase by 11%. In addition to fuel production, effects of weather and heavy traffic regions were found to significantly impact emissions at global and regional levels. The global annual efficiency for different fuels and ship segments in approximated operational conditions were also investigated, indicating the need for more holistic metrics than current ones when seeking appropriate solutions aiming at reducing emissions.

Human-made impacts on the acoustic environment from marine industries is becoming a more significant issue with increasing public concern of environmental consequences. Even though there are several reports with scientific evidences on harmful influences of anthropogenic underwater sounds on the aquatic ecosystem, most of the studies so far dealt with trigger effects of short term noise impacts on aquatic animals. In the present study, however, long-term experimentation was conducted with Nile tilapia (Oreochromis niloticus) in order to figure out how fish may respond to long-term exposure of underwater sounds and if the level of response may change (increase or decline) over time. A startle reflex as a sign of stress was seen immediately at the start of the playbacks of ship noise or urban sounds in this study. Peaks of elevated respiratory movements of ventilation (opercula beats and pectoral wing rates) retained high over the following 30 days of sound initiation and underwent a declining trend over the following 90 days of exposure. At the end of the 120-day study period, the lowered response of fish after long-term sound exposure is likely due to the increased tolerance of fish to human-generated underwater sounds of urban and shipping noises. Different than short-term noise impacts, information on long-term exposure of anthropogenic underwater sounds is important for environmental management and setting new regulations for the sustainable use of water resources in the world.

Background: Cognitive ability refers to the ability to receive, process, store, and extract information. It is the most important psychological condition for people to successfully complete activities. Previous studies have shown that the design of the human-computer interface of the command and control system cannot exceed the cognitive ability of the operator of the command and control system, and it must match the cognitive ability of the operator in order to reduce the mental load intensity, and improve the accuracy, timeliness and work efficiency. However, previous researchers in the field of cognitive science have not put forward a core index system that can represent the cognitive ability of ship command and control system operators and the importance of each index, and there are few achievements that can be used for reference., Objective: To explore the core index system of cognitive ability that affecting the cognitive process of command and control system operators, and to verify the index system., Methods: Based on the classic O*NET questionnaire, two indexes of O*NET were revised, three indexes of response ability were added, and then a questionnaire on the importance evaluation of cognitive abilities index was formed. The questionnaire includes 24 indexes in six aspects: verbal abilities, idea generation and reasoning abilities, quantitative abilities, visual perception abilities, mnemonic and attentive abilities, and response abilities. The cognitive ability importance evaluation data of 202 people from different positions in the ship command and control system were collected. These data reflect the overall level of cognitive ability of operators in the whole ship command and control field., Results: The data analysis results show that: firstly, the most important cognitive abilities affecting command and control system operators were visual perception abilities, mnemonic and attentive abilities, and response abilities. Secondly, the results of confirmatory factor analysis show that CMIN/DF, GFI, CFI, TLI, RMSEA, RMR and other indicators used in the model test all meet the requirements. The model has a good fitting degree, and the overall index extraction method is feasible. Thirdly, the independence T test results show that for beginners and experienced experts, there is a significant difference in the important evaluation of mnemonic and attentive abilities, while there is no significant difference in the important evaluation of response and visual perception abilities. Fourthly, the results of Bi-group confirmatory factor analysis experiment show that the structural model has good stability and factor invariance., Conclusions: Through the research of this paper, the index system which can express the core cognitive ability of the commander of command and control system is successfully constructed, and the index system has been fully verified by mathematics. The 3 abilities and 10 indexes in the index system are closely related to the work tasks of operators, which also reflects the correctness of our construction results to a certain extent. According to the results of data analysis, there are differences between assistant commanders and professional commanders in the evaluation of the importance of some indexes, which reflects the importance of working age and experience to the promotion of position skills. The results of this research are of great significance for the subsequent acquisition of cognitive ability data and assessment of post cognitive ability of command and control system operators., Competing Interests: NO authors have competing interests.

Waste heat recovery from shipboard machineries could be a potential source for heat treatment of ballast water. Similar to a shipboard schematic arrangement, a laboratory-scale engine-heat exchanger set-up harvesting waste heat from jacket water and exhaust gases was erected to test the level of species' mortalities. Mortalities were also assessed under experimental conditions for cultured and natural plankton communities at laboratory level. Effect of pump impellers on species' mortalities were also tested. Exposures between 60°C and 70°C for 60 sec resulted in 80-100% mortalities. Mortalities due to pump impeller effects were observed in the range of 70-100% for zooplankton. On the laboratory-scale arrangement, >95% mortalities of phytoplankton, zooplankton and bacteria were recorded. It was demonstrated that the temperature of tropical sea waters used as secondary coolant can be raised to cause species' mortalities, employing engine exhaust gases. The results also indicated that pump impeller effects will enhance species' mortalities. The limitations of the shipboard application of this method would be the large ballast volumes, flow rates and time for treatment.

Computer-aided solutions are essential for naval architects to manage and optimize technical complexities when developing a ship's design. Although there are an array of software solutions aimed to optimize the human element in design, practical ergonomics methodologies and technological solutions have struggled to gain widespread application in ship design processes. This paper explores how a new ergonomics technology is perceived by naval architecture students using a mixed-methods framework. Thirteen Naval Architecture and Ocean Engineering Masters students participated in the study. Overall, results found participants perceived the software and its embedded ergonomics tools to benefit their design work, increasing their empathy and ability to understand the work environment and work demands end-users face. However, participant's questioned if ergonomics could be practically and efficiently implemented under real-world project constraints. This revealed underlying social biases and a fundamental lack of understanding in engineering postgraduate students regarding applied ergonomics in naval architecture., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Purpose: To get knowledge of the work environment for seafarers sailing under the Swedish flag, in terms of safety climate, ergonomical, chemical and psychosocial exposures, and the seafarers self-rated health and work ability., Methods: A Web-based questionnaire was sent to all seafarers with a personal e-mail address in the Swedish Maritime Registry (N = 5608). Comparisons were made mainly within the study population, using Student's t test, prevalence odds ratios and logistic regressions with 95% confidence intervals., Results: The response rate was 35% (N = 1972; 10% women, 90% men), with 61% of the respondents working on deck, 31% in the engine room and 7% in the catering/service department (1% not classifiable). Strain on neck, arm or back and heavy lifting were associated with female gender (p = 0.0001) and younger age (below or above 30 years of age, p < 0.0001). Exposures to exhausts, oils and dust were commonly reported. Major work problems were noise, risk of an accident and vibrations from the hull of the ship. The safety climate was high in comparison with that in land-based occupations. One-fourth had experienced personal harassment or bullying during last year of service., Conclusions: Noise, risk of accidents, hand/arm and whole-body vibrations and psychosocial factors such as harassment were commonly reported work environment problems among seafarers within the Swedish merchant fleet., Competing Interests: The authors declare that they have no conflict of interest.

Despite their ban on small vessels in 1989 in the EU, organotin compounds (OTCs) are still being released into the environment due to their presence in historic paint layers on leisure boats. 23 paint samples scraped from recreational boats from three countries around the Baltic Sea were analyzed for total tin (Sn) and OTCs. Two antifouling paint products were also subjected to the same analyses. A new method for the detection of Sn in paint flake samples was developed and found to yield more accurate results compared to four different acid digestion methods. A new method was also developed for the extraction of OTCs from ground paint flakes. This endeavor revealed that existing methods for organotin analysis of sediment may not have full recoveries of OTCs if paint flakes are present in the sample. The hull paint samples had Sn concentrations ranging from 25 to 18,000 mg/kg paint and results showed that tributyltin (TBT) was detected in all samples with concentrations as high as 4.7 g (as Sn)/kg paint. TBT was however not always the major OTC. Triphenyltin (TPhT) was abundant in many samples, especially in those originating from Finland. Several other compounds such as monobutyltin (MBT), dibutyltin (DBT), tetrabutyltin (TeBT), monophenyltin (MPhT) and diphenyltin (DPhT) were also detected. These could be the result of degradation occurring on the hull or of impurities in the paint products as they were also identified in the two analyzed paint products. A linear correlation (r 2  = 0.934) was found between the total tin content and the sum of all detected OTCs. The detection of tin can therefore be used to indicate the presence of OTCs on leisure boats., (Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The wintertime maritime traffic operations in the Gulf of Finland are managed through the Finnish-Swedish Winter Navigation System. This establishes the requirements and limitations for the vessels navigating when ice covers this area. During winter navigation in the Gulf of Finland, the largest risk stems from accidental ship collisions which may also trigger oil spills. In this article, a model for managing the risk of winter navigation operations is presented. The model analyses the probability of oil spills derived from collisions involving oil tanker vessels and other vessel types. The model structure is based on the steps provided in the Formal Safety Assessment (FSA) by the International Maritime Organization (IMO) and adapted into a Bayesian Network model. The results indicate that ship independent navigation and convoys are the operations with higher probability of oil spills. Minor spills are most probable, while major oil spills found very unlikely but possible., (Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.)

During the last decades the shipping industry has undergone rapid technical developments and experienced hard economic conditions and increased striving for profitability. This has led to reduced staffing and changes in task performance, which has been reported to increase workload for the remaining seafarers. The working conditions on board have a number of distinct and in many ways unique characteristics, which makes the job demands and resources for seafarers unique in several ways. The purpose of this study was to assess how engine room staff perceives how these major technical and organizational changes in the shipping industry have affected job demands as well as resources. The study compiled individual interviews and focus groups interviews with engine crew members where they were asked to elaborate on the psychosocial work environment and the major changes in the working conditions on board. Engine crew describes a work situation where they feel a lack of resources. The content of the work has changed, staffing has been reduced, new tasks are being added but the organization of the crew and the design of the work place remains unaltered., (Copyright © 2016 Elsevier Ltd and The Ergonomics Society. All rights reserved.)

Tributyltin (TBT) and other organotin compounds have been restricted for use on leisure boats since 1989 in the EU. Nonetheless, release of TBT is observed from leisure boats during hull maintenance work, such as pressure hosing. In this work, we used a handheld X-ray Fluorescence analyser (XRF) calibrated for antifouling paint matrixes to measure tin, copper and zinc in antifouling paints coated on leisure boats in Sweden. Our results show that over 10% of the leisure boats (n = 686) contain >400 μg/cm(2) of tin in their antifouling coatings. For comparison, one layer (40 μm dry film) of a TBT-paint equals ≈ 800 μg Sn/cm(2). To our knowledge, tin has never been used in other forms than organotin (OT) in antifouling paints. Thus, even though the XRF analysis does not provide any information on the speciation of tin, the high concentrations indicate that these leisure boats still have OT coatings present on their hull. On several leisure boats we performed additional XRF measurements by progressively scraping off the top coatings and analysing each underlying layer. The XRF data show that when tin is detected, it is most likely present in coatings close to the hull with several layers of other coatings on top. Thus, leaching of OT compounds from the hull into the water is presumed to be negligible. The risk for environmental impacts arises during maintenance work such as scraping, blasting and high pressure hosing activities. The data also show that many boat owners apply excessive paint layers when following paint manufacturers recommendations. Moreover, high loads of copper were detected even on boats sailing in freshwater, despite the more than 20 year old ban, which poses an environmental risk that has not been addressed until now., (Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Measurements of particle number and mass concentrations and number size distribution of particles from a ship running on liquefied natural gas (LNG) were made on-board a ship with dual-fuel engines installed. Today there is a large interest in LNG as a marine fuel, as a means to comply with sulfur and NOX regulations. Particles were studied in a wide size range together with measurements of other exhaust gases under different engine loads and different mixtures of LNG and marine gas oil. Results from these measurements show that emissions of particles, NOX, and CO2 are considerably lower for LNG compared to present marine fuel oils. Emitted particles were mainly of volatile character and mainly had diameters below 50 nm. Number size distribution for LNG showed a distinct peak at 9-10 nm and a part of a peak at diameter 6 nm and below. Emissions of total hydrocarbons and carbon monoxide are higher for LNG compared to present marine fuel oils, which points to the importance of considering the methane slip from combustion of LNG.

This paper aims to analyze the effectiveness of maritime safety control from the perspective of safety level along the Yangtze River with special considerations for navigational environments. The influencing variables of maritime safety are reviewed, including ship condition, maritime regulatory system, human reliability and navigational environment. Because the former three variables are generally assumed to be of the same level of safety, this paper focuses on studying the impact of navigational environments on the level of safety in different waterways. An improved data envelopment analysis (DEA) model is proposed by treating the navigational environment factors as inputs and ship accident data as outputs. Moreover, because the traditional DEA model cannot provide an overall ranking of different decision making units (DMUs), the spatial sequential frontiers and grey relational analysis are incorporated into the DEA model to facilitate a refined assessment. Based on the empirical study results, the proposed model is able to solve the problem of information missing in the prior models and evaluate the level of safety with a better accuracy. The results of the proposed DEA model are further compared with an evidential reasoning (ER) method, which has been widely used for level of safety evaluations. A sensitivity analysis is also conducted to better understand the relationship between the variation of navigational environments and level of safety. The sensitivity analysis shows that the level of safety varies in terms of traffic flow. It indicates that appropriate traffic control measures should be adopted for different waterways to improve their safety. This paper presents a practical method of conducting maritime level of safety assessments under dynamic navigational environment., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Shipwrecks on the sea floor around the world may contain hazardous substances that can cause harm to the marine environment. Today there are no comprehensive methods for environmental risk assessment of shipwrecks, and thus there is poor support for decision-making on prioritization of mitigation measures. The purpose of this study was to develop a tool for quantitative risk estimation of potentially polluting shipwrecks, and in particular an estimation of the annual probability of hazardous substance discharge. The assessment of the probability of discharge is performed using fault tree analysis, facilitating quantification of the probability with respect to a set of identified hazardous events. This approach enables a structured assessment providing transparent uncertainty and sensitivity analyses. The model facilitates quantification of risk, quantification of the uncertainties in the risk calculation and identification of parameters to be investigated further in order to obtain a more reliable risk calculation., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

The aerodynamic characteristics of the wing-in-ground effect (WIG) craft model that has a noble configuration of a compound wing was experimentally investigated and Universiti Teknologi Malaysia (UTM) wind tunnel with and without endplates. Lift and drag forces, pitching moment coefficients, and the centre of pressure were measured with respect to the ground clearance and the wing angle of attack. The ground effect and the existence of the endplates increase the wing lift-to-drag ratio at low ground clearance. The results of this research work show new proposed design of the WIG craft with compound wing and endplates, which can clearly increase the aerodynamic efficiency without compromising the longitudinal stability. The use of WIG craft is representing an ambitious technology that will help in reducing time, effort, and money of the conventional marine transportation in the future.

In risk assessment of maritime transportation, estimation of accidental oil outflow from tankers is important for assessing environmental impacts. However, there typically is limited data concerning the specific structural design and tank arrangement of ships operating in a given area. Moreover, there is uncertainty about the accident scenarios potentially emerging from ship encounters. This paper proposes a Bayesian network (BN) model for reasoning under uncertainty for the assessment of accidental cargo oil outflow in a ship-ship collision where a product tanker is struck. The BN combines a model linking impact scenarios to damage extent with a model for estimating the tank layouts based on limited information regarding the ship. The methodology for constructing the model is presented and output for two accident scenarios is shown. The discussion elaborates on the issue of model validation, both in terms of the BN and in light of the adopted uncertainty/bias-based risk perspective., (Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Misunderstanding each other's intentions is one of the most common causes of shipping accidents. By sending out a number of waypoints ahead and displaying them on the Electronic Chart Display and Information System (ECDIS) a ship's intentions would be clearly visible for other ships. Displaying ships' intentions would be a major change compared to navigation today. It could be very beneficial but it could also have unintended consequences. This paper reports on findings from an evaluation looking for unintended consequences of change using system simulation. During the simulation an unanticipated behavior was observed. Bridge crews started to click and drag waypoints too negotiate crossing situations ahead of time. The behavior could be compared to agreeing over the VHF. However further research is needed to evaluate this new behavior and how it aligns to COLREGS., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

Shipwrecks deteriorate and the probability of a release of oil increases with time on the sea floor. The potential leakage is a risk to the marine environment and may also have social and economic consequences. The purpose of this study was to evaluate existing methods for risk assessment of shipwrecks and suggest a generic risk assessment framework. A risk assessment is necessary for providing decision support on remediation actions and thus enabling an efficient use of available resources. Existing risk assessment methods aimed for assessing shipwrecks were evaluated by comparison to relevant parts of an international standard on risk management. The comparison showed that existing methods lack several key components of risk assessment procedures. None of the evaluated methods provide a comprehensive risk assessment for potentially polluting shipwrecks and few take into account uncertainty and sensitivity. Furthermore, there is a need to develop risk assessment methods considering long-term effects of continuous release of oil into the marine environment. Finally, a generic comprehensive framework for risk assessment of shipwrecks is suggested., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

Vessel Traffic Service (VTS) is a shore-side service implemented by a "Competent Authority to improve the safety and efficiency of vessel traffic and to protect the environment". It is a service that operates through VTS centers, from which VTS operators monitor traffic, assist in navigational matters and provide information to all ships in a designated area. As VTS is provided by operators located on shore, they usually make use of several decision support systems to be able to monitor the traffic and to provide information to the vessels. Although several new tools and approaches have been introduced in the VTS domain, there is still room for improvements. This paper summarizes the results from three studies conducted within the EfficienSea project to approach user needs for dynamic risk management in the VTS domain. Data was collected by conducting study visits and observations at VTS centers, a focus group interview as well as several semi-structured interviews. The paper summarizes the results and presents technical and organizational user needs for dynamic risk management within the VTS domain.

Transmission of intended and suggested routes to and from electronic chart systems has been identified as a user need. The idea was discussed during a focus group meeting and two field studies in fringe fields like search and rescue (SAR) and ice breaking. A prototype test was then conducted during a SAR drill. The features were very well received by all the participants in the drill. A system simulation with two ships and a VTS station was also conducted in a full mission bridge simulator. Preliminary results are very promising. Behavior with vessels in conflicting situations suggested that the intended routes could facilitate understanding when negotiating with or without VHF communication. No major concerns were expressed by the professional crew members that participated.

Underreporting of maritime accidents is a problem not only for authorities trying to improve maritime safety through legislation, but also to risk management companies and other entities using maritime casualty statistics in risk and accident analysis. This study collected and compared casualty data from 01.01.2005 to 31.12.2009, from IHS Fairplay and the maritime authorities from a set of nations. The data was compared to find common records, and estimation of the true number of occurred accidents was performed using conditional probability given positive dependency between data sources, several variations of the capture-recapture method, calculation of best case scenario assuming perfect reporting, and scaling up a subset of casualty information from a marine insurance statistics database. The estimated upper limit reporting performance for the selected flag states ranged from 14% to 74%, while the corresponding estimated coverage of IHS Fairplay ranges from 4% to 62%. On average the study results document that the number of unreported accidents makes up roughly 50% of all occurred accidents. Even in a best case scenario, only a few flag states come close to perfect reporting (94%). The considerable scope of underreporting uncovered in the study, indicates that users of statistical vessel accident data should assume a certain degree of underreporting, and adjust their analyses accordingly. Whether to use correction factors, a safety margin, or rely on expert judgment, should be decided on a case by case basis., (Copyright © 2011 Elsevier Ltd. All rights reserved.)

The specific problems associated with the work on board within the merchant fleet are well known and have over the years been a topic of discussion. The work conditions in the engine room (ER) are demanding due to, e.g. the thermal climate, noise and awkward working postures. The work in the engine control room (ECR) has over recent years undergone major changes, mainly due to the introduction of computers on board. In order to capture the impact these changes had implied, and also to investigate how the work situation has developed, a total of 20 engine officers and engine ratings were interviewed. The interviews were semi-structured and Grounded Theory was used for the data analysis. The aim of the present study was to describe how the engine crew perceive their work situation and working environment on board. Further, the aim was to identify areas for improvements which the engine crew consider especially important for a safe and effective work environment. The result of the study shows that the design of the ECR and ER is crucial for how different tasks are performed. Design which does not support operational procedures and how tasks are performed risk inducing inappropriate behaviour as the crew members' are compelled to find alternative ways to perform their tasks in order to get the job done. These types of behaviour can induce an increased risk of exposure to hazardous substances and the engine crew members becoming injured., (Copyright © 2010 Elsevier Ltd and The Ergonomics Society. All rights reserved.)

Background: Today many merchant ships sail with only two nautical officers, working a shift schedule of 6 hr on and 6 hr off. There are concerns that such a shift schedule is related to fatigue. However, little data exist from onboard studies of seafarers., Methods: Data were collected on board 13 ships. Fifteen participants worked on a 6-on, 6-off watch system and another 15 on a 4-on, 8-off watch system. Electrooculography, actigraphy, diaries, and reaction time tests were used to measure the effects of shift system on fatigue and sleep., Results and Conclusions: Sleepiness was higher during the night shift in the 6-on, 6-off system. Moreover, sleepiness increased more during the watch in the 6-on, 6-off system compared to the 4-on, 8-off system. There was a trend toward shorter sleep episodes in the 6-on, 6-off system and sleep was more often split into two episodes., (2010 Wiley-Liss, Inc.)

This paper presents the results of field emission measurements that have been carried out on the 4500-kW four-stroke main engine on-board a product tanker. Two fuel qualities--heavy fuel oil (HFO) and marine gas oil (MGO)-have been tested on the same engine for comparable load settings. A fuel switch within the marine sector is approaching and the aim of this study is to draw initial conclusions on the subsequent effects on ship exhaust gas composition and emission factors with a focus on particles. Measurements on exhaust gas concentrations of carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur dioxide (SO2), total hydrocarbons (HCs), and particulate matter (PM) were conducted. The gases, except SO2, did not show any major differences between the fuels. Specific PM emissions were generally higher for HFO than for MGO; however, for the smallest size-fraction measured containing particles 0.30-0.40 microm in diameter, the opposite is observed. This finding emphasizes that to minimize negative health effects of particles from ships, further regulation may be needed to reduce small-sized particles; a fuel shift to low sulfur fuel alone does not seem to accomplish this reduction. The average of this and previously published data from on-board studies on particle emissions from ships results in emissions factors of 0.33 and 1.34 g/kWh for marine distillate oil (MDO) and HFO, respectively. Accounting for 1 standard deviation in each direction from the average values gives a range of 0.18-0.48 g/kWh for MDO and 0.56-2.12 g/kWh for HFO.

A number of marine organisms are able to resist fouling pressure and remain essentially free of fouling. Some organisms are totally devoid of even the first stages of biofilm formation involving bacteria and microalgae. A key feature in recent research has been the realisation that previous low adherence technology is an insufficient technical solution and that natural models, based on marine and other organisms, incorporate other passive techniques for fouling resistance. These characteristics may be incorporated into physical analogues of the natural processes. This paper describes ways of producing physical analogues of some such characteristics, the application of such techniques to surfaces in the marine environment and the environmental impact. The paper includes some results of recent trials and a cost comparison.