Search

Laser-ablated template and fluoroalkyl silane modified composite coatings are used to prepare a micro- and nano-structure on silicone rubber surfaces. By testing the surface potential accumulation and dissipation process, we assess the suppression of surface charge on superhydrophobic silicone rubber. The surface physicochemical properties and resistivity are examined. The electron and hole trap distribution are analysed using isothermal current decay theory. Peak density of traps associated with the superhydrophobic surfaces are found to be promoted to lower energy levels relative to unmodified silicone. Surface micro-structure increases trap density and reduce trap depth; nano coatings are shown to further reduce surface trap depth. The improvements shown to suppress surface charge accumulation is beneficial to a range of electrical industries and helps mitigate surface flashover on insulation. [ABSTRACT FROM AUTHOR]

The effects of liquids immersion and subsequent drying on the surface properties of filled high temperature vulcanized (HTV) silicone rubber have been reported in this series of paper. In this first paper, the surface hydrophobicity characterized by static contact angle and surface chemical properties characterized by a comprehensive analysis of Fourier transform infrared spectroscopy (FTIR), X-Ray diffraction (XRD) and thermal desorption gas chromatography mass spectrometry (TD-GC/MS) have been studied. The liquids employed in this study were deionized water, NaCl solution and nitric acid solution, which represented the actual liquids that composite insulators could encounter in practice use. As for the NaCl solution, the lower the concentration, the greater its impact on the hydrophobicity of the silicone rubber (the deionized water can be considered as the NaCl solution of concentration of 0 mol/L). As for the nitric acid solution, the higher the concentration, the greater its impact on the hydrophobicity of silicone rubber. During the permeation process of deionized water and NaCl solution into HTV silicone rubber, some Alumina Tri-hydrate (ATH) filler and low molecular weight (LMW) could be dissolved into the liquids. Nitric acid solution not only dissolved the ATH filler, but also interacted with the ATH filler and degraded the polymer matrix. [ABSTRACT FROM AUTHOR]

This study utilized a multi-needle corona electrode system to investigate the influence of AC and DC coronas on the surface properties of high temperature vulcanized (HTV) silicone rubber. Contact angle measurements and X-ray photoelectron spectroscopy (XPS) analysis were performed to characterize the chemical structure and hydrophobicity changes in state of the silicone rubber surface after corona exposure. The results indicated that the effects of AC corona were greater than that of DC corona, and the effects of negative DC corona were slightly greater than that of positive DC corona. XPS results showed that the C elemental content on the silicone rubber surface decreased, whereas the O elemental content increased. High-resolution scan on Si 2p XPS spectra proved that surface oxidation occurred during corona exposure and caused the high binding energies of Si atoms and silica-like layer. High-resolution C 1s XPS spectra showed that corona exposure destroyed the Si-CH3 groups on the surface. Some C-O and C=O bonds appeared following the corona exposure. High-resolution O 1s XPS spectra confirmed the formation of Si-OH groups and chemically absorbed water, which was ignored in the past research. Chemically absorbed water was detected as one of the essential factors that caused the loss of hydrophobicity of silicone rubber after corona exposure, together with Si-OH groups and silica-like layer. [ABSTRACT FROM PUBLISHER]

This paper investigates the liquid permeation performance of silicone rubber containing alumina tri-hydrate (ATH) that has been modified with N-[3-(trimethoxysilyl) propyl] aniline (Y-9669). From the change in weight during immersion in water, saline solution or nitric acid, and during subsequent drying in air as well as a second immersion test, it is revealed that the majority of the absorbed liquid exists in filler and interface for silicone rubber with original ATH. Surface modification of ATH filler can protect silicone rubber from liquid permeation. It is easier for liquid to permeate into silicone rubber than to escape from it due to the hydrophobicity of the silicone rubber matrix. A cycle of immersion and drying is found to have little impact on subsequent immersion in the case of water and saline solutions; however, damage inflicted on the matrix and filler by nitric acid means that the rate of permeation increases during subsequent immersion. The volume resistivity and surface resistivity of samples with unmodified ATH also decrease more appreciably than those with modified ATH after a cycle of immersion and air drying due to the amount of the residual absorbed liquid. [ABSTRACT FROM AUTHOR]

Capacitance and gravimetric measurements are used to study the diffusion of water into high temperature vulcanized (HTV) silicone rubber. Silicone rubber with different Alumina Tri-hydrate (ATH) filler contents was used in this research, and deviations from the classical Fickian diffusion were observed. A model is presented for the calculation of the diffusion coefficient of water in silicone rubber by capacitance method in which the anomalous diffusion mechanism and the water concentration profile are considered. The present model is compared to other models and the difference between the diffusion coefficients obtained is analyzed. [ABSTRACT FROM PUBLISHER]

In this paper, the permeation properties of three types of liquids into HTV silicone rubber with different Alumina Tri-hydrate (ATH) contents had been investigated by weight gain experiments. The influence of differing exposure conditions on the diffusion into silicone rubber, in particular the effect of solution type, solution concentration, and test temperature were explored. Experimental results indicated that the liquids permeation into silicone rubber obeyed anomalous diffusion ways instead of the Fick diffusion model. Moreover, higher temperature would accelerate the permeation process, and silicone rubber with higher ATH content absorbed more liquids than that with lower ATH content. Furthermore, the material properties of silicone rubber before and after liquid permeation were examined using Fourier infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA) and scanning electron microscopy (SEM), respectively. The permeation mechanisms and process were discussed in depth by combining the weight gain experiment results and the material properties analyses. [ABSTRACT FROM PUBLISHER]