Search

The study aims to analyze the strength properties obtained from three-point bending tests of epoxy-glass composite samples modified by adding rubber recyclate. A pure epoxy-glass composite is used as a comparative variant. The tested materials, which varies in the percentage of rubber recyclate and distribution, are cut through waterjet cutting to minimize the influence of temperature. The results undergo statistical analysis, and the microstructures are examined using scanning electron microscopy. The decreasing bending strength of the composites is observed, as the content of rubber recyclate in the material increased. However, adding rubber recyclate directly into the resin subtly decreases in bending strength compared to adding in the layers between the glass mat layers. Composites with rubber recyclate exhibits lower deflection under load compared to pure composites. The most favorable bending test parameters are obtained for the material containing 5% rubber recyclate distributed in three layers. [ABSTRACT FROM AUTHOR]

This paper presents the results of investigations of the mechanical properties of epoxy–glass composites with the addition of rubber recyclate. For the purposes of the study, seven variants of materials were designed and manufactured, which differed in terms of the percentage of recyclate content (3, 5 and 7%) and the way the recyclate was distributed in the composite (one, two and three layers with a constant share of 5%). Tests of comparative mechanical properties were carried out using a static tensile test. As a result of the conducted tests, the following values were obtained for all variants of materials: tensile strength (Rm), Young's modulus (E) and percentage relative strain ε. In addition, for a deeper analysis of the results obtained, statistical calculations of Kolgomorov–Sinai EK-S metric entropy were performed on the experimental data sets, which were then analyzed. The results of the analysis indicate that the application of metric entropy calculations EK-S can be helpful in identifying changes in the internal structure of the composite material that occur during its loading, and which do not manifest themselves in any other tangible way. The data obtained as a result of the research can be used to optimize production processes and to determine the further direction of development of epoxy–glass composites with the addition of rubber recyclate, while saving time and resources. [ABSTRACT FROM AUTHOR]

The paper presents acoustic studies of a multilayer composite made based on Synolite 1967-G-1 polyester resin and glass fabric with a three-way arrangement of +/-45° fibres, Triaxial type and a weight of 860 g/m2. As an addition, rubber recyclate created in the process of disposal of car tires was used. The material was made using the vacuum infusion method. By the vacuum lamination method, composite materials were produced in the form of plates with the addition of rubber recyclate in four variants of the amount of recyclate used in the produced composite - 20%, 30%, 40% and 50%. Each variant contained 6 layers of fabric and five layers of rubber recyclate. The samples were tested in the vibroacoustic laboratory on a dedicated measuring station of a set of reverberation chambers without flanking transmission, in which the specific acoustic insulation Rw was determined following PN-EN ISO 10140-2 and related standards, i.e. PN-EN ISO 10140-1, PN-EN ISO 10140-2, PN-EN ISO 10140-4, PN-EN ISO 10140-5 and PN EN ISO 717-1. All manufactured variants of the composite material with the addition of rubber recyclate were characterized by acoustic insulation in the range of Rw = (30.0 ÷ 35.7) dB. High sound insulation parameters for tested panels up to 12 mm thick act as a barrier to counteracting the spread of unwanted airborne noise. Combined with good mechanical properties such as tensile strength, toughness and hardness, they form the basis for the easy design of all shields in many industries. The use of rubber recyclate obtained in the process of disposal of car tires has a positive impact on improving environmental protection. [ABSTRACT FROM AUTHOR]

Currently, there is a noticeable trend of modifying new materials by using additives from the recycling of harmful waste. This is to protect the environment by using waste to produce composites and at the same time to reduce the cost of their production. The article presents an analysis of the impact of the use of rubber recyclate obtained from the utilization of car tires as a sandwich layer of epoxy–glass composites and its impact on the strength parameters of the composite. The presented research is an extension of the previously conducted analyses on composite materials modified with the addition of rubber recyclate. The four variants of the materials produced contained the same percentage amount of rubber recyclate, but differed in the way it was distributed and the number of layers. Static tensile tests as well as impact strength and kinetics of damage to samples made with and without the addition of recyclate were carried out. Observation of the structures of the materials with the use of SEM was also performed. A significant influence of the method of distributing the recyclate in layers on the strength parameters of the materials was found. In the case of composites with three and two sandwich layers of recyclate, more favorable results were obtained compared to the blank sample. In addition, the values of the impact strength measurements were subjected to statistical analysis at the significance level of α = 95%. The distributions were tested for normality with the Shapiro–Wilk test, differences between pairs were tested with the Student's t-test for dependent groups, and ANOVA differences were tested for independent groups. Using the Student's t-test, it was confirmed that between the pairs of variables in the configurations reference sample and modified sample, there were significant statistical differences in the distribution of impact strength measurement results for all the analyzed materials. Statistical analysis showed a significant usefulness in the selection of the material with the best strength parameters and a significant role of statistical methods in the study of anisotropic materials. [ABSTRACT FROM AUTHOR]

The article attempts to assess the possibility of using rubber recyclate as a component of composite materials. Research is being carried out to develop a technology for the production of composite materials with the addition of rubber waste. These tests are aimed at increasing the reliability and safety of the operation of structures exposed to longterm impact of devices generating vibrations. At the same time, work is underway on the use of complex composite surfaces as sound-absorbing elements. The new direction of using recyclates will have a positive impact on the management of environmentally harmful waste, taking into account a favorable economic factor. [ABSTRACT FROM AUTHOR]

The aim of the research was to analyze the strength parameters of epoxy-glass sandwich composites with the addition of rubber recyclate. Material samples were subjected to a static tensile test performed on a universal testing machine in accordance with the current standard for fiber-reinforced composite materials. The test results showed that the addition of rubber recyclate increases the plastic parameters of the composite, which allows considering the use of the tested material for structures loaded with the vibration and noise scale. The use of rubber recyclate to modify the strength parameters of the composite allows to reduce the amount of rubber waste and ensures the durability of the new material. [ABSTRACT FROM AUTHOR]