Search

Lumped-parameter thermal models (LPTMs) have been widely used to estimate critical temperatures in permanent magnet synchronous machines (PMSMs). However, in some cases, they may be incapable of predicting the hotspots and even cause temperature misestimation. In this paper, the synergized lumped-parameter and sub-domain thermal models are proposed for surface-mounted PMSMs to track the hotspots in the most vulnerable components, i.e., active/end-windings and rotor magnet. Firstly, the “T-type” elementary network based LPTM is developed to predict the average temperatures in main components and the boundary conditions. Secondly, the boundary conditions are applied to three sub-domain thermal models for the active/end-windings and the rotor magnet to predict the respective hotspots and to further correct the misestimated average temperatures. Finally, the proposed synergized thermal model is verified by the experiments on a prototype surface-mounted PMSM under various load conditions. [ABSTRACT FROM AUTHOR]

Consequent-pole (CP) permanent magnet (PM) configuration suffers asymmetric electromagnetic characteristics although it saves PM usage. The CP-based stator-PM synchronous machines are investigated in this paper, with particular reference to symmetrical issues. The electromagnetic performances of the CP-based stator-PM synchronous machines are firstly evaluated. Afterwards, the rule of even order harmonics cancellation is presented for different slot/pole number combinations and winding layouts, based on which symmetrical phase flux-linkages can be obtained although the unbalanced magnetic flux naturally occurs. Moreover, based on the three-dimensional finite element analysis, the unipolar end leakage-flux caused by the asymmetric magnetic field is identified, and the risk of the shaft magnetization is revealed. Finally, a pair of prototype machines are fabricated and measured to validate the analyses. [ABSTRACT FROM AUTHOR]

Voltage induced in the dc winding by the armature field in wound field switched flux (WFSF) machines will induce voltage perturbation in the voltage supply and cause dc winding current ripple and field excitation fluctuation. This will challenge the dc voltage controller and deteriorate the control performance, especially when the load and/or the rotor speed are high. In this article, the dual three-phase armature winding design with a phase-shift of 30 electrical degrees is employed in the partitioned stator WFSF machines to reduce the on-load dc winding-induced voltage. Analytical deductions and finite element (FE) results demonstrate that the dominant sixth-order-induced voltage harmonic can be suppressed to zero. Hence, the peak-to-peak induced voltage in the 12/11- and 12/13-pole partitioned stator WFSF machines can be reduced by 83.35% and 82.53%, respectively. Due to the improvement of winding factors, the torque densities are 4.85% and 5.60% higher, respectively. Prototypes are built and tested to verify the analytical and FE results. [ABSTRACT FROM AUTHOR]

This article proposes and investigates two asymmetric consequent-pole hybrid excited flux reversal machine (AS-CP-HEFRM) topologies, which have same numbers of iron poles and permanent magnets (PMs) with concentrated ac and dc windings on each stator pole and a salient pole rotor. If PM number on one stator pole is larger than 1, PMs are magnetized radially in the same direction on one stator pole, while opposite on adjacent stator poles. The phenomenon of the phase shift between the flux linkages of dc and PM excitations in the AS-CP-HEFRMs is revealed for the first time, which will weaken the regulation of dc excitation field to PM produced field. The elimination condition of the phase shift is derived and verified by finite-element analysis in this article, which can be considered as design guidelines in AS-CP-HEFRMs. Airgap magnetic field space harmonics of AS-CP-HEFRM are also investigated and verified by finite-element analyses. Meanwhile, the relationship between the rotor pole number and the stator pole arc (PM ratio) is derived and verified by global optimization based on genetic algorithm for maximum average torque. The influence of stator/rotor pole number combinations is also studied and compared in terms of torque, torque ripple, and flux regulation capability. The torque components produced by airgap magnetic field space harmonics are calculated and compared. A prototype has been built and tested to validate the finite element calculations. [ABSTRACT FROM AUTHOR]

Hybrid excited machines, with synergies of permanent magnet (PM) and wound field (WF) excitations, exhibit high torque density as well as controllable flux and are perceived as promising candidate for variable speed application. A novel doubly salient hybrid excited (DSHE) machine with non-overlapped field winding is presented in this paper. It inherits simple structure of conventional doubly salient PM (DSPM) machine and facilitates the regulation of magnetic field by field winding. The electromagnetic performances of the proposed machine with different stator and rotor pole number combinations are investigated by finite element method (FEM), confirming these advantages. Furthermore, the effect of iron bridge on the hybridization between PM and WF excitations is analyzed to obtain a trade-off between high torque density and wide flux regulation range with the frozen permeability method (FPM). It is revealed that the proposed DSHE machine possesses higher power and fault tolerance at flux weakening region compared with the DSPM machine, albeit with sacrificed torque density and efficiency with introduction of field winding. Finally, a prototype is fabricated and tested to validate the theoretical analyses. [ABSTRACT FROM AUTHOR]

The induced voltage ripple in DC field windings can cause many problems in hybrid excitation machines (HEMs). It can generate ripple current in field winding, thus causing unsteady magnetic field excitation and hence additional torque ripple and losses. Besides, the torque and power density of hybrid excitation machines may be deteriorated as a result of the influence of the induced voltage ripple on field winding's excitation circuit, particularly under high-speed conditions. Based on a hybrid excitation switched flux machine (HESFM), the influence of stator slot and rotor pole number combination on no-load and on-load field winding induced voltage ripples are studied and compared by the finite element method (FEM). It reveals that the harmonic content and thus the peak-to-peak value of the field winding induced voltage ripple are closely related to the stator slot and rotor pole number combination at both no-load and on-load operating conditions. The FEM calculations are verified by experiments on a prototype HESFM. [ABSTRACT FROM AUTHOR]

Spoke array permanent magnet (PM) flux reversal machines (SAFRPMMs), which are suitable for low speed and high torque applications, are able to enhance torque density due to the flux focusing effect. In this paper, what influence both the number of PM per slot and the PM shape have on their electromagnetic performance are investigated. The results show that both the PM number and the PM shape have significant effects on the performance of SAFRPMMs, and proper selections are critical in designing high performance machines. When the PM number per slot is 2, the SAFRPMM exhibits the best electromagnetic performances, i.e., the highest torque, power, efficiency, and power factor. Meanwhile, by properly designing the PM shape, the torque can be further improved by around 11%. A prototype is made and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

In this article, a simple position error correction method is proposed to minimize the influence of parameter deviation on the model-based rotor position estimation, with the help of two sets of windings in a dual 3-phase permanent magnet synchronous machine (PMSM). In the proposed method, when each set of 3-phase windings is individually used for sensorless rotor position estimation, the nominal parameters that are set in each observer are identical but inaccurate, which leads to errors in the estimated rotor position from both observers. Since the error is varied according to the current level, small current pulses are injected respectively into d- or q-axis of one set (or both set) of 3-phase windings, which causes the difference between the rotor position estimation errors from two sets of 3-phase windings. This difference is subsequently used as the input of an updated controller to minimize the parameter deviation and the corresponding rotor position error. The proposed method is experimentally validated on a dual 3-phase PMSM system. [ABSTRACT FROM AUTHOR]

This article investigates novel fractional slot nonoverlapping winding hybrid excited (HE) machines with consequent-pole permanent magnet (PM) rotors. The proposed machines accommodate the rotor PM and stator field winding separately, which has solved the spatial confliction of double excitations. Different consequent-pole interior PM rotor configurations are extended to retain the PMs and utilize the flux-concentrating effect. Then, the relationship of field and armature current ratio with the PM and wound field fluxes is identified theoretically, which provides design and optimization guidelines for the HE machines. Furthermore, the HE machines are optimized and compared with conventional PM machines. It is revealed that the HE machines exhibit enhanced torque density with flux-enhancing field excitation, and extended operation range with flux-weakening field excitation. Besides, the HE machine utilizing flux-concentrating effect exhibits the highest PM torque but sacrificed flux regulation capability due to magnetic saturation. Finally, the HE prototypes with different rotor configurations are fabricated and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

In this article, a new type of consequent pole flux reversal permanent magnet (CFRPM) machine, which features more iron poles than PM poles under one stator tooth, is proposed to improve the torque density. The proposed CFRPM machine with 6 slots and 16 poles (6S16P) is compared with a 12S16P FRPM machine and its consequent pole type, as well as a conventional 6S4P surface-mounted PM (SPM) machine. The proposed 6S16P CFRPM shows the highest torque among the four machines, together with the highest torque per PM volume. For a fair comparison with the 12S16P FRPM machine and its consequent pole type, the torque ripple of the proposed 6S16P CFRPM is suppressed by using two-step skewed rotor. After employing 4° two-step skewed rotor, while exhibits comparable torque ripple, the proposed 6S16P CFRPM still has 43% and 22% higher torque compared with the 12S16P FRPM machine and its consequent pole type. [ABSTRACT FROM AUTHOR]

The second harmonic current injection method is recently developed to enhance the torque density of variable flux reluctance machines (VFRMs). This article investigates the feasibility and effectiveness of the second harmonic current injection method in VFRMs with different stator/rotor pole combinations. By using magnetic gearing effect, it is found that the second harmonic injection method can only be applied to the 6j/(6i ± 2)j (i, j = 0, 1, 2…) stator/rotor pole VFRMs for the torque density enhancement. For the other stator/rotor pole combinations, the second harmonic current has no contribution in average torque production but only leads to excessive torque ripple. Further, by using global optimization method and finite element analysis, 6/8 stator/rotor pole combination is proved to be the optimal stator/rotor pole combination for 6-stator-slots VFRMs with the second harmonic current injection method, being able to exceed the maximal torque density of conventional VFRMs by 12% at a fixed copper loss. [ABSTRACT FROM AUTHOR]

Hybrid excited (HE) machines have the synergies of high torque density and high efficiency of permanent magnet (PM) machines and excellent flux controllability of wound-field machines. The PMs and field coils (FCs) coexist in HE machines to provide excitations simultaneously, and can be coupled either in series or parallel. The topologies of HE machines are very diverse, which bring challenges in the selection and design of HE machines. Based on the partitioned stator (PS) platform, a pair of series and parallel HE machines having similar structures and PM usage are evaluated and compared to identify their merits and demerits. With the help of finite element analysis, the flux regulation, energy conversion capability, parasitic effects and irreversible demagnetization of the two kinds of the HE machines are comprehensively investigated and the guidance to the machine design is provided. A pair of prototypes are fabricated and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

In order to provide the general guidance in constructing the novel modular machines with redundant teeth, the available slot and pole number combinations based on the balanced conditions are summarized in this article. After the brief review of the machine structure, the general slot and pole number combinations are listed: Firstly, the conventional modular machines used to construct the proposed modular machines need to possess integer times of 3 repetitive machine units. Each machine unit should construct as a 3-phase type. Then, a redundant machine unit providing the redundant teeth for modularity is necessary. This redundant machine only has one pole pair to make sure the space waste is minimal. The slot number of this redundant machine is determined by the greatest common divisor of the slot and pole pair numbers of the conventional modular machine. Finally, the combination of the conventional modular machine and the redundant one generates the proposed modular machine. In order to clearly illustrate the influence of slot and pole number combinations on machine performance, four combinations are chosen as examples to be compared. A 42-slot/32-pole machine is prototyped and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

This paper proposes a consequent-pole flux reversal machine (CP-FRM) with biased flux modulation theory, which employs homopolar permanent magnets (PMs) placed between the adjacent stator poles. The machine topology is introduced from the perspective of FRM with a shifted magnet position and CP arrangement, and the performance comparison between the proposed CP-FRM and its original surface-mounted PM (SPM) counterpart is presented to highlight the torque improvement of the CP structure. Then, a simplified permeance model is applied to the CP-FRM to identify the principal effective air-gap field harmonics engaging in the torque productions. It shows that the CP-FRM works based on a biased flux modulation effect due to its asymmetric air-gap field distribution caused by the CP configuration, which unveils its underlying torque improvement mechanism over its SPM-FRM counterpart. In order to obtain the highest torque capability, the key design parameters are analytically optimized by analyzing the winding configuration, which aids the establishment of a general design guideline for the CP-FRM. The analytical and FE results are validated by experiments. [ABSTRACT FROM AUTHOR]

A novel parallel hybrid excited (HE) machine with wide flux regulation range is proposed in this paper. The flux paths of permanent magnet (PM) and field winding are separated to avoid irreversible demagnetization and achieve improved flux regulation capability. Since the field winding and armature winding are located in the same stator slots, open-winding drive circuit can be employed to feed biased ac excitation in one set of winding and solve the spatial confliction of conventional hybrid excited machine. Finite element (FE) method is utilized to analyze the electromagnetic performances of the proposed HE machine, in comparison with the original HE machine. It is revealed that the proposed HE machine exhibits lower PM excited back-electromotive force (EMF), which is beneficial to high speed fault tolerant operation. Besides, the torque density can be higher with flux enhancing, albeit with reduced PM usage. Finally, a prototype is manufactured and tested to validate the FE predictions. [ABSTRACT FROM AUTHOR]

In order to ease the manufacture process of very large permanent magnet (PM) machines, such as direct drive wind power generators, modularity technique is usually adopted. Although conventional fractional slot PM machines with all teeth wound windings show good performance, the coils located at the end part of each segment could be easily damaged because of being exposed to the air. In addition, the local winding faults could easily proliferate to the whole machine due to the physical touch of adjacent coils. Thus, a novel modular fractional slot PM machine with redundant teeth is proposed in this paper, while three phases within each set of winding are still balanced. The construction of the proposed modular PM machine having 42-slots/32-poles (42S/32P) combination is described in detail as an example, which can be treated as the integration of six 6S/5P segments and a redundant 6S/2P machine. The reason for using 6S/2P machine is to get rid of the undesirable unbalanced magnetic force (UMF), which usually exists in rotating asymmetric machines, such as 3S/2P PM machine. Since the end part of each segment in the proposed modular PM machine can be covered by half redundant tooth during the production, more protection can be provided for coils located in these regions. Furthermore, the separation of six segments can improve the fault-tolerant capability of the machine. The electromagnetic performance predicted by finite-element analysis (FEA) also demonstrates that the proposed modular machine will perform better if dual three-phase winding is adopted. Finally, the experiments on the prototyped machine validate the analysis in the paper. [ABSTRACT FROM AUTHOR]

In the safe-critical applications such as electric/hybrid electric vehicles, the reliability of the machine drive system is vital. Among the various machine fault types, the uncontrolled generator fault (UCGF) at high speed is one of the most serious faults that could damage the machine drive system. In this paper, the fault protection capability of a novel hybrid-excited doubly salient synchronous machine (HEDSSM) is examined to illustrate its great capability to prevent the dangerous overvoltage issue from the UCGF. Permanent magnet flux of the novel HEDSSM is inherently short-circuited when the field excitation current is not fed into the excitation windings. Therefore, when the UCGF is detected in the high-speed region, the dc-link overvoltage issue can be effectively reduced by forcing the field excitation current to zero. Since only the field excitation current is utilized to protect the machine and power inverter from the UCGF, it is easy to implement and the concept of proposed control strategy can also be applied to other hybrid-excited machines. Finally, the proposed control strategy is verified by both simulation and experimental results on the HEDSSM. [ABSTRACT FROM AUTHOR]

For hybrid-excited doubly salient synchronous machine, both the field excitation current and the d-axis current can be utilized to adjust the flux-linkage, which provides more flexible control parameters for flux-weakening operation. In this paper, three flux-weakening control methods, i.e., utilizing field excitation current alone (Method I), utilizing armature current alone (Method II), and optimal method (Method III), are proposed and compared. All three methods can achieve similar torque performance in the constant-torque region. In the flux-weakening region, Method I exhibits low torque and limited operating speed range. The operating speed range can be further extended by Methods II and III. In addition, Method III can provide a higher efficiency in flux-weakening region than Method II since the copper loss of field winding can be decreased in proportion to the reduction of field excitation current. Those flux-weakening control methods are verified by experimental results. [ABSTRACT FROM AUTHOR]

This paper aims to comprehensively analyze the influence of number of permanent magnet (PM) pieces on electromagnetic performance of flux reversal permanent magnet (FRPM) machines. First, the unified analytical model of FRPM machines having different numbers of PM pieces is established, from which the optimal number of PM pieces and the corresponding rotor pole number can be identified. It shows that by employing the optimal number of PM pieces instead of the conventional two on each stator tooth, additional back-EMF component can be generated which is beneficial to boost the machine performance. Then, the influence of critical design parameters including stator slot opening ratio, split ratio, and stator slot number is investigated, providing a guidance to the design of FRPM machines aiming at maximum output torque. In addition, both finite element analyses and experimental tests are conducted to verify the analytical analyses. For 6-slot-stator FRPM machines, experimental results show that more than 40% higher output torque can be achieved in the machine with optimal number of PM pieces when compared to the conventional one. [ABSTRACT FROM AUTHOR]

This paper investigates the torque production and the torque ripple reduction of a six-stator/seven-rotor-pole (6/7) variable flux reluctance machine (VFRM). As a main advantage, the 6/7 VFRM produces higher torque density, but less torque ripple compared with the 6/4 VFRM. The instantaneous torque equation of the 6/7 VFRM is derived by considering the spectra of the winding inductance and current. Based on the derived equation, the average torque is found to be mainly produced by the mutual inductance between the field and armature windings. The even-order harmonics of self-inductance and odd-order harmonics in mutual inductance between the field and armature windings are eliminated due to the opposite polarity connection of the armature coils in each phase. This results in the elimination of the third harmonic torque ripple, while a multiple of the sixth harmonic torque ripple exists. In order to mitigate the sixth harmonic torque ripple, the harmonic current injection method is implemented into the field winding. The field harmonic current is calculated from the analytical torque ripple equation. The performance of the proposed methods is verified by both finite element analysis (FEA) and experiment. [ABSTRACT FROM AUTHOR]

A new type of three-phase stator hybrid excited machine with permanent magnets (PMs) located at the slot openings of field winding slots is presented in this paper. It has the advantage of good flux regulation capability due to the field excitation. The machines with different stator/rotor pole combinations, i.e., 6-stator pole and 7-/8-/10-/11-/13-/14-rotor poles, have been comparatively investigated in terms of the open-circuit and on-load characteristics, as well as the influence of dc current and the unbalanced magnetic forces. The 2-D finite element analysis (FEA) has been employed for analysis and optimization of the machines together with experimental validation. [ABSTRACT FROM AUTHOR]

In this paper, the open-circuit dc-winding-induced voltage in a wound field switched flux (WFSFs) machines is analyzed. The phenomenon of open-circuit dc-winding-induced voltage is illustrated and the mechanism is explained. Rotor skewing is proposed to reduce the open-circuit dc-winding-induced voltage, and the optimal skewing angle is analytically derived based on the analytically deduced harmonic orders of the open-circuit dc-winding-induced voltage. Finite-element (FE) analyses show that the open-circuit dc-winding-induced voltages in the analyzed 12-stator-pole partitioned stator WFSF machines having 10-, 11-, 13-, and 14-rotor-pole rotors can be effectively reduced by >94%, while the ac-winding phase-fundamental back-EMFs can be maintained by >95%. Twelve/ten-stator/rotor-pole prototypes with skewed and nonskewed rotors are built and tested to verify the analytical and FE results. [ABSTRACT FROM AUTHOR]

DC winding induced voltage pulsation in the wound field synchronous machines (WFSMs) will cause dc winding current ripple, challenge the dc power supply, and deteriorate the control performance, especially at high speed. In this paper, the influence of dc winding configuration including the dc coil number and the parallel branch number on its induced voltage pulsation is investigated for WFSMs. Based on the modeling of both open-circuit and on-load dc winding induced voltages, the preferred dc winding configurations for WFSMs having various stator/rotor pole number combinations with double layer or single layer ac windings are obtained and validated by finite element (FE) analysis on four typical partitioned stator WFSMs (PS-WFSMs). A PS-WFSM prototype is built and tested to validate both analytical and FE analyses. [ABSTRACT FROM AUTHOR]

This paper introduces a novel hybrid-excited stator slot opening permanent magnet (PM) machine (HSSPMM). The operation principle of the machine is described and the effects of rotor eccentricity and magnetic saturation due to PMs on electromagnetic performance, with particular emphasis on back electromotive force (EMF), are analyzed by finite element method (FEM). It shows that different from the conventional PM machines, the open-circuit back EMF in this novel HSSPMM should be zero but may become non-zero if significant magnetic saturation exists, and furthermore, the rotor eccentricity has a detrimental effect on the waveforms, amplitudes, and symmetries of three-phase back EMFs, as confirmed by FEM and tests. [ABSTRACT FROM AUTHOR]

This paper investigates the influence of pole number and stator outer diameter on the performance of superconducting (SC) generators. The SC generator has an iron-cored rotor topology. First, the generator structure is introduced and the optimization procedure is described. Then, the influence of design parameters on performance, in terms of generator volume, weight, SC wire utilization, active material cost, etc., is presented. Some relationships for the optimal combinations for different performance attributes are established. In addition, the influence of SC material price on the determination of optimal stator outer diameter and pole number is discussed. Finally, the influence of SC coil area per pole on performance is also investigated. [ABSTRACT FROM PUBLISHER]

In this paper, a harmonic field current injection method is proposed for torque ripple reduction in 6-stator/4-rotor-pole (6s/4r) variable flux reluctance machines (VFRMs). Initially, the torque production of VFRM is analyzed based on an analytical torque model and harmonic analysis. The torque ripple of 6s/4r VFRM is found to have multiples of third harmonics. Then, one finite-element analysis (FEA)-based and one analytical equation-based method are developed to calculate the magnitude of the injected harmonic current. Both methods are proved to be effective in torque ripple reduction. Finally, the influence of the inductance mismatch on the proposed method is investigated. It shows that the torque ripple reduction performance is not affected much unless the fundamental component of nominal inductance is underestimated. The feasibility and effectiveness of the proposed methods are validated by both 2-D FEA and experimental test. [ABSTRACT FROM AUTHOR]

A novel partitioned stator (PS) hybrid excited (HE) switched flux (SF) (PS-HESF) machine is proposed in this paper. In the PS-HESF machine, the permanent magnets (PMs) and field windings are allocated on one stator while the armature windings are placed on the other. The iron-piece-rotor is sandwiched between the two stators. Consequently, compared with the conventional HESF machine having PMs, field windings as well as armature windings all on one stator, the available space of the novel machine is greatly boosted and therefore the performance is enhanced. Based on 2-D finite-element analysis, the electromagnetic performance of the PS-HESF machine is evaluated and the results reveal that it can exhibit not only better flux regulation capability but also higher torque than the conventional HESF machine. Moreover, the influences of the key design parameters on the hybridization ratio in the PS-HESF machines are investigated. A prototype machine is manufactured and tested to validate the predictions. [ABSTRACT FROM PUBLISHER]

Partitioned stator (PS) machines employ two separated stators to accommodate armature windings and permanent magnets (PMs), respectively, alleviating the space conflict in stator-PM machines, and hence boosting the torque density. However, the PM usage volume in PS machines is relatively large, and thus the material cost is high, which is undesirable for the cost-sensitive applications. In this paper, a PS machine employing ferrite PM is presented, which takes advantage of larger available space for PMs while balances the performance and cost. The electromagnetic characteristics of an optimized ferrite PS machine and an NdFeB PS machine are evaluated together with a classic Prius2010 interior PM (IPM) machine as a baseline. Meanwhile, the economic issues are considered. The results reveal that the NdFeB PS machine has higher torque density than the Prius2010 IPM machine, but is more expensive, while the ferrite PS machine can significantly reduce the cost and still exhibit good performance. The demagnetization behavior of the ferrite PS machine is evaluated and a new method to improve the demagnetization withstand capability is proposed. Moreover, the mechanical analysis is conducted for the cupped rotor of PS machines. Finally, a pair of small-scaled prototypes are manufactured to validate the predictions. [ABSTRACT FROM PUBLISHER]

Hybrid excited (HE) machines combine the advantages of both high torque density and excellent flux regulation capability, while also having extensive applications. A novel partitioned stator HE machine employing two stators to allocate armature windings and excitations separately, is proposed in this paper. The permanent magnet (PM) pole-pair and wound field pole-pair are alternately placed on one stator to exhibit parallel magnetic paths, while the armature windings are located on the other stator. The iron-piece-rotor is sandwiched between the two stators. This machine inherits the advantages of stator-PM machine and further benefits from attractive flux regulation capability due to parallel topology. The operating principle and the slot/pole combination rule that are different from the conventional PM machine are illustrated. The two-dimensional finite element technique is used to evaluate the electromagnetic performance, confirming the mentioned advantages. A prototype is manufactured and tested to validate the predictions. [ABSTRACT FROM PUBLISHER]

A partitioned stator hybrid excited machine is proposed, in which the permanent magnets and field windings are alternately placed on an inner stator separated from the outer stator having armature windings. This machine inherits the features of brushless machines and benefits from better space utilization. The operating principle and the effects of slot/pole combinations are investigated in detail. Further, based on 2-D finite-element analysis, the electromagnetic performances of the proposed machines, including back-electromotive force, cogging torque, flux regulation range, torque capability, power factor and torque–speed curve, are evaluated. The results reveal that the proposed machines can exhibit wide flux regulation range as well as good torque density. The prototype is manufactured and tested to validate the predictions. [ABSTRACT FROM PUBLISHER]

In order to simplify the manufacturing process of variable reluctance (VR) resolvers for hybrid electric vehicle/electric vehicle (HEV/EV) applications, a novel VR resolver with nonoverlapping tooth–coil windings is proposed in this paper. A comparison of the winding configurations is first carried out between the existing and the proposed designs, followed by the description of the operating principle. Furthermore, the influence of actual application conditions is investigated by finite-element (FE) analyses, including operating speed and assembling eccentricity. In addition, identical stator and windings of the novel design can be employed in three resolvers of different rotor saliencies. The voltage difference among the three rotor combinations, as well as the detecting accuracy, is further investigated. Finally, prototypes are fabricated and tested to verify the analyses. [ABSTRACT FROM PUBLISHER]

A dual-stator hybrid-excited switched-flux (DS-HESF) machine, which is based on the conventional SF permanent magnet machine but employs a secondary stator to accommodate the field windings, is proposed in this paper. The DS-HESF machine inherits the robust rotor and benefits from a better space utilization. The topology and operating principle of the proposed machine are introduced in detail. Based on the 2-D finite-element analysis, the comparison between the DS-HESF machines having different rotor pole numbers is carried out, accompanied with a conventional HESF machine as a baseline. The results reveal that the DS-HESF machines exhibit not only higher torque density but also a better flux regulation capability. The prototype is manufactured and tested to validate the predictions. [ABSTRACT FROM PUBLISHER]

Novel stator slot permanent magnet (SSPM) machines with doubly salient structure have attractive features, such as a robust rotor and fail-safe capability during faults due to their peculiar PM excitation characteristics. In this paper, average electromagnetic torque production in SSPM machines is investigated using the frozen permeability analysis for the 12/10 stator/rotor pole machine. The single layer (SL) and double layer (DL) winding SSPM machines with 12/10 stator/rotor poles are further investigated, accounting for the influence of stator tooth-tips. The key findings include that the average electromagnetic torque can be enhanced by 9%–10% at the rated current for the DL and SL winding machines with stator tooth-tips. The influence of design parameters, open-circuit characteristics, inductances, electromagnetic torque, torque ripple, and losses is studied. Finally, the 2-D finite-element analysis is experimentally validated. [ABSTRACT FROM AUTHOR]

This paper proposes a new partitioned stator flux reversal permanent magnet (PM) (PS-FRPM) machine having integer-slot overlapping windings, i.e., the slot number per pole per phase q is an integer, based on the magnetic gearing effect in stator-PM machines. Compared with the existing PS-FRPM machine with fractional-slot nonoverlapping windings, a more sinusoidal armature reaction magnetomotive force can be achieved in the proposed PS-FRPM machine with integer-slot overlapping windings, resulting in lower iron loss and PM loss. Electromagnetic performance of the PS-FRPM machine, which has q = 1 overlapping windings is analyzed and compared with PS-FRPM machine, which has q = 0.5 nonoverlapping windings by finite element (FE) analysis. FE results show that the proposed 24/10/12-outer-stator/rotor/inner-stator-pole PS-FRPM machine with q = 1 overlapping winding exhibits higher fundamental phase back-electromotive force, higher average electromagnetic torque and lower torque ripple, lower loss and higher efficiency, higher self-inductance but lower mutual inductance, higher d-axis inductance, and potential infinite flux-weakening capability compared with the 12/10/12-outer-stator/rotor/inner-stator-pole PS-FRPM machine with q = 0.5 nonoverlapping windings. Both prototype machines with q = 1 overlapping winding and q = 0.5 nonoverlapping windings are built and tested to verify the FE analyzes. [ABSTRACT FROM PUBLISHER]

This paper proposes an integrated field and armature current control strategy for a variable flux reluctance machine (VFRM) with an open-winding topology. By using an open-winding inverter, the field and armature currents can be injected into a single coil as a sinusoidal current biased by the dc offset rather than the separated field and armature windings. The integrated current control can reduce the copper loss to half and extend the operating speed range owing to the reduction in the winding resistance. In order to utilize the zero-sequence current as a field current, a zero-vector modification technique is proposed, in which the switching-on time of the zero vectors is modified to generate the constant zero-sequence voltage between two inverters. The proposed scheme is implemented in a synchronous $dq0$-axis frame with space vector modulation. For the validation of the proposed method, a machine model of the VFRM is developed and implemented in MATLAB/Simulink. The simulation and experimental results verify that the proposed strategy can effectively reduce the copper loss and extend the operating speed range. [ABSTRACT FROM AUTHOR]

This paper proposes a novel rotor contour design for variable reluctance (VR) resolvers by injecting auxiliary air-gap permeance harmonics. Based on the resolver model with nonoverlapping tooth-coil windings, the influence of air-gap length function is first investigated by finite element (FE) method, and the detection accuracy of designs with higher values of fundamental wave factor may deteriorate due to the increasing third order of output voltage harmonics. Further, the origins of the third harmonics are investigated by analytical derivation and FE analyses of output voltages. Furthermore, it is proved that the voltage harmonics and the detection accuracy are significantly improved by injecting auxiliary air-gap permeance harmonics in the design of rotor contour. In addition, the proposed design can also be employed to eliminate voltage tooth harmonics in a conventional VR resolver topology. Finally, VR resolver prototypes with the conventional and the proposed rotors are fabricated and tested respectively to verify the analyses. [ABSTRACT FROM PUBLISHER]

The hybrid-excited stator slot permanent magnet (HSSPM) machines have good flux regulation capability due to the dc excitation. This makes them attractive candidates for variable speed applications. In this paper, the choices of stator/rotor pole combinations for an arbitrary number of armature phases are discussed. The three-phase 12-10/11/13/14 stator/rotor poles HSSPM machines with single- and double-layer windings are further investigated. Their open-circuit characteristics, torque, inductances, and unbalanced magnetic forces are comparatively studied using 2-D finite-element analysis (FEA). Finally, the 2-D FEA is experimentally validated. [ABSTRACT FROM AUTHOR]

The partitioned stator (PS) machine adopts two stators to allocate windings and permanent magnets (PMs) separately, increasing the space for PMs as well as armature coils to boost the electromagnetic torque and improving the thermal condition of PMs. In this paper, the PS switched-flux PM (PS-SFPM) machine and the PS flux reversal PM (PS-FRPM) machine are proved to inherently share the same operating principle and similar machine topology but with interior PM (IPM) and surface-mounted PM stators, respectively. Furthermore, four globally optimized PS machines with different inner stator topologies are compared in terms of back EMF, cogging torque, electromagnetic torque, torque per PM volume, and flux-weakening capability. The results reveal that the spoke-shaped IPM (IPM-spoke) inner stator exhibits the highest back EMF and hence the highest average torque, while the I-shaped IPM (IPM-I) stator has the best flux-weakening capability, and the V-shaped IPM (IPM-V) produces the highest torque per PM volume. Furthermore, four machines are redesigned with the same PM usage volume, and the results show that the PS-SFPM machine still exhibits the highest back EMF as well as torque although with sacrificed advantages. The finite-element analyses and experiments are used to confirm the predictions. [ABSTRACT FROM AUTHOR]

In switched-flux permanent-magnet machines, winding coil connections can be rearranged into several types of machine winding configurations (MWCs), such as all poles wound, alternate poles wound, and single and dual three-phase windings. This paper investigates the influence of machine saliency on a sensorless control operation based on different MWCs. First, by injecting an HF carrier signal, the machine saliency level can be evaluated experimentally. The influence of saliency on an HF-signal-injection-based sensorless operation for different MWCs can be then investigated irrespective of any information of machine parameters. However, the secondary saliency caused by magnetic saturation or current harmonics may exist in a machine, due to which the sensorless control performance will deteriorate. Hence, an orthogonal signal-based position tracking observer is proposed to improve the accuracy of rotor position estimation rather than utilizing an existing position observer. Furthermore, experimental results confirm that a prototype machine exhibits different saliency characteristics and apparent saliency, in which the HF-injection-based sensorless control technique can be applied. Moreover, better steady and dynamic state performance can be achieved by the improved position estimator compared with using an existing position observer. [ABSTRACT FROM AUTHOR]

A novel type of partitioned stator switched flux permanent magnet (PS-SFPM) machine with either single-layer or double-layer windings is developed in this paper. The proposed PS-SFPM machines have two stators, which separately accommodate the armature windings and the PMs, and between which is the rotor made of iron pieces, while the number of stator poles with PMs may be equal or half of that with armature windings. All the machines are optimized under fixed copper loss for maximum average torque by genetic algorithm. Their electromagnetic performances are compared, such as open-circuit flux-linkages and back-electromotive forces (EMFs), cogging torque, static torque waveforms, average torque against current, PM utilization ratio, and flux-weakening performances. The results show that due to more PM usage and higher open-circuit back-EMF, the PS-SFPM machines having the number of stator poles with PMs the same as that with armature windings exhibit higher average torque, irrespective of the winding topologies, either single-layer or double-layer windings. However, the single-layer winding PS-SFPM machines having the number of stator poles with PMs half of that with armature windings have the best PM usage and the highest ratio of average torque to PM volume, as well as good flux-weakening capability. A prototype machine is manufactured and tested to validate the analyses. [ABSTRACT FROM PUBLISHER]

In this paper, partitioned stator flux reversal permanent magnet (PS-FRPM) machines having different stator/rotor pole combinations with consequent-pole PM (CPM) stator are proposed and analyzed. Compared with the conventional 12-stator-pole PS-FRPM machines having 10-, 11-, 13-, and 14-rotor-pole rotors and surface-mounted PM (SPM) stator, the PM volume in the proposed PS-FRPM machines with CPM stator can be saved by 28.33%, 30%, 30%, and 33.33%, respectively, while the torque density are similar, i.e., 98.59%, 96.69%, 95.50%, and 97.15%, respectively. Besides, the proposed PS-FRPM machines with CPM stator can exhibit only <1% smaller efficiency compared with the existing PS-FRPM machines with SPM inner stator. [ABSTRACT FROM AUTHOR]

The local magnetic saturation in tooth-tips of surface-mounted permanent magnet (SPM) machines generates on-load terminal voltage distortion, especially when small or closed slot openings are adopted. This paper focuses on investigating the influence of slot and pole number (Ns/2p) combinations on this phenomenon in both fractional slot and integer slot SPM machines. The mechanism of this phenomenon and how it is influenced by current advance angle and tooth-tip geometric parameters are introduced first. Then, voltage distortion pattern is proposed to analyze the occurring time or rotor positions of voltage ripples and their relative amplitudes according to the winding arrangements of different Ns/2 p combinations, with the influence of PM leakage flux considered. By 2-D finite-element analysis, the voltage distortion of various machines is calculated and compared, such as Ns \pm 1 = 2p, Ns \pm 2 = 2p, N s/2p = 3/2 (3/4), and integer slot machines with slot number per pole per phase q = 1 or 2. The analysis results reveal that under the same comparison conditions, the integer slot machines have less voltage distortion than the fractional slot machines, especially when q \geq 2. Meanwhile, for the same slot number, the fractional slot machines with Ns > 2p suffer from on-load voltage distortion less than their counterparts with Ns < 2p. Finally, three prototype machines with 12/10, 12/14, and 12/8 slot/pole numbers are manufactured and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

Three-phase nonoverlapping stator wound-field synchronous (NSWFS) machines having salient pole rotors are investigated systematically in this paper. The influence of the rotor pole number on the NSWFS machines is investigated via optimized designs. Using two-dimensional (2-D) finite-element analysis (FEA), the NSWFS machines are found to exhibit higher torque than the nonoverlapping segmented rotor NSWFS (SNSWFS) machines. The FEA-predicted back-electromotive force (EMF), cogging torque, and static torque of the NSWFS machines are validated by experiments on prototype machines. [ABSTRACT FROM AUTHOR]

This paper presents dual three-phase permanent magnet (PM) machines utilizing third-harmonic back electromotive force (EMF) and current to improve the output torque, but the torque ripple remains almost similar. The feasibility and practical issues of dual three-phase machines with third-harmonic EMF and current are first discussed, and the output torque is analytically derived. Furthermore, the optimal value of the third harmonic injected into a current waveform for maximum torque improvement is also analytically derived and validated by finite-element analysis (FEA) with the consideration of the constraints of both the peak and root-mean-square currents. For feasible dual three-phase PM machines, torque characteristics, including the average torque and the torque ripple, are compared without and with third-order harmonic injection. It is found that, for a dual three-phase machine without third-harmonic back EMF, the optimal third harmonic into the current is 1/6 of the fundamental current, and the average torque with the current having the optimal third harmonic injected can be improved by 15%. However, for the dual three-phase PM machines with third-harmonic back EMF, the optimal third harmonic into the current is dependent on the ratio of the third-harmonic back EMF to the fundamental back EMF, and the interaction of the third-harmonic current and the third-harmonic EMF results in the further improvement of the output torque. Finally, the experiments on a prototype are given to verify both the analytical and FEA methods. [ABSTRACT FROM PUBLISHER]

Three-phase nonoverlapping stator wound-field synchronous (NSWFS) machines employing salient pole rotors are proposed in this paper. Based on the optimized design, the influence of rotor pole number on the proposed machine is investigated. According to 2-D finite-element analysis (FEA), it is found that the proposed machine shows higher torque density and lower torque ripple compared with the existing NSWFS machines. The operation principles of the proposed machine under different pole numbers are presented and compared in this paper. The FEA-predicted back electromotive force, cogging torque, and static torque of NSWFS machines are validated by experiments made on the prototypes. [ABSTRACT FROM AUTHOR]

This paper investigates the performance of sensorless control of switched-flux permanent-magnet synchronous machines (SFPM) with different stator winding topologies, such as all poles wound (double-layer winding) and alternate poles wound (single-layer winding), whose back electromotive force (EMF) exhibit different waveform characteristics, i.e., sinusoidal, asymmetric, and non-sinusoidal waves. Most importantly, it is found that the single-layer SFPM machine is with asymmetric back-EMFs, due to which the performance of sensorless control will deteriorate. In order to minimize this influence, a control strategy is developed for the improvement of accuracy of rotor position estimation, which is based on the elimination of back-EMF harmonics and not sensitive to the machine parameters. In addition, it also shows that the developed strategy is easy for implementation and the experimental results confirm that the influence of asymmetric and non-sinusoidal back-EMF can be effectively compensated. Consequently, an improvement in the accuracy of rotor position estimation is achieved at both steady and dynamic states as compared with those conventional methods without compensation. [ABSTRACT FROM PUBLISHER]

A novel stator hybrid-excited, parallel flux path, synchronous machine of doubly salient topology is proposed. It has the novel features of: 1) hybrid dc field and permanent magnet (PM) excitation in the stator; 2) magnets placed in the slots between adjacent salient stator poles; and 3) the magnetic poles of PMs arranged, such that the flux premagnetizes the stator, but it is in a direction to oppose the dc excitation flux. The electromagnetic characteristics of the machine are analyzed on open-circuit and load. Since the new machine topology is developed from the variable-flux machine (VFM), a comparison of their electromagnetic torque and machine losses is conducted. The average electromagnetic torque of the hybrid-excited machine can be increased by 18% for fixed copper loss in comparison with the VFM due to the reduction of magnetic saturation in the stator. It is also shown that at high temperatures some risk of PM demagnetization exists when excited with dc and armature currents due to fringing flux that exists between the stator and the rotor poles. However, this affects only a very small area of the PMs. The performance of the hybrid-excited machine is predicted by a 2-D finite-element analysis and experimentally validated. [ABSTRACT FROM AUTHOR]

Several switched flux permanent magnet (SFPM) machines with mechanically movable flux adjusting technique are proposed, analyzed, and compared for applications which demand high speed and efficiency. By using ferromagnetic pieces-–one per every stator pole or every alternative stator pole, which are named as flux adjusters (FAs) and located on the outside surface of the stator—the airgap flux density can be weakened and therefore the operation speed range and flux weakening capability can be improved. The influence of using all or alternative FAs on the open circuit results, electromagnetic performance, and torque–speed characteristics of the SFPM machine is investigated through three SFPM machines with different stator/rotor pole combinations, i.e., 12/10, 12/13, and 12/14. Moreover, although using FAs in all stator poles can significantly improve the flux weakening capability, alternative FAs can also achieve remarkable improvement although higher torque ripple is observed. Additionally, it has been found that the 12/13 combination is considered to be the most suitable candidate for alternative FAs technique. In addition to 2-D finite-element analysis (FEA) and analytical methods, 3-D FEA results accounting for the end-effect are presented. Furthermore, experiments are performed to validate the results. [ABSTRACT FROM AUTHOR]

A novel variable reluctance (VR) resolver with nonoverlapping tooth–coil windings is proposed in this paper. It significantly simplifies the manufacturing process of multilayer windings in conventional products. Finite element (FE) analysis is used to illustrate the basic operating principle, followed by analytical derivation of main parameters and optimization of major dimensions, including air-gap length and slot opening width. Based on winding distributions and FE results, it is shown that identical stator and winding can be employed for a resolver with three different numbers of rotor poles. Further, other stator slot/rotor pole combinations based on the nonoverlapping tooth–coil windings are generalized. In addition, the influence of eccentricity and end-winding leakage on the proposed topology is investigated. Finally, a prototype is fabricated and tested to verify the analysis, including main parameters and electrical angle error. [ABSTRACT FROM AUTHOR]

In this paper, a double stator (DS) wound field (WF) switched flux (SF) (DS-WFSF) machine is proposed. In the DS-WFSF machine, field and armature windings are separately placed in two different stators. Compared with the conventional WFSF machine with single stator, in which both field and armature windings are located, nonoverlapping concentrated windings and large slot areas can be obtained in the DS-WFSF machine. The proposed DS-WFSF machine exhibits >19% higher torque than the conventional WFSF machine, with both machines having the same space envelope and being globally optimized. The influence of leading design parameters, such as copper loss ratio between the field and armature windings, air-gap diameter, and rotor iron piece thickness and widths, on the average output torque is investigated for the DS-WFSF machines having 12/10, 12/11, 12/13, and 12/14 stator slots/rotor iron pieces. All the analyses are confirmed by both finite element and experimental results. [ABSTRACT FROM AUTHOR]