Search

The hydrogen-fueled Wanke rotary engine is a promising power system that has both high power and eco-friendly properties. This work investigated the effect of ignition timing on a dual-spark plugs synchronous-ignition hydrogen-fueled Wankel rotary engine under low speed, part load and lean combustion. The results show that with delaying the ignition timing, CA0-10 is shortened first and then lengthened and CA10-90 is consistently shortened. When the CA50 is located between 35 and 40°CA ATDC, the maximum brake torque can be realized. Besides, the selection of ignition timing needs to consider the "trade-off" relationship between the combustion phase and corresponding in-cylinder pressure. The maximum brake torque ignition timing is between 5 and 10°CA ATDC. And there is also a "trade-off" relationship between stability and thermal load when ignition timing is selected. In addition, HC and NO emissions will not become the problem limiting the power performance of hydrogen-fueled Wankel rotary engine under this operating condition. • A modified synchronous ignition hydrogen Wankel rotary engine was used. • The effect of ignition timing on performance of rotary engine was studied. • The power depends mainly on the in-cylinder pressure near 135°CA ATDC. • Selecting ignition timing needs to weigh the stability and thermal load. • Suitable ignition timing makes CA50 located between 35 and 40°CA ATDC. [ABSTRACT FROM AUTHOR]

Abstract The comparative study on performance of the hydrogen/gasoline and hydrogen/n-butanol rotary engines was conducted in the present paper. Considering the stable operation of the engine, for both hydrogen/gasoline case and hydrogen/n-butanol case, the operating conditions were set at: 4000 rpm (engine speed), 35 kPa (intake pressure) and 30 °CA BTDC (spark timing). The total excess air ratio of mixture was maintained at 1.0 through all the tests. The testing results displayed that hydrogen enrichment improved performance of both gasoline and n-butanol rotary engines. To be more specific, brake thermal efficiency was increased, flame development and propagation periods were shortened, the coefficient of variation in flame propagation period was decreased, and the emissions of HC and CO were decreased. NOx emissions were mildly increased after hydrogen addition. Besides, hydrogen/n-butanol rotary engine possessed the similar performance to hydrogen/gasoline rotary engine. Highlights • Performance of HGRE and HBRE was studied. • BTE and Tmax was increased after H 2 blending. • CA0-10, CA10-90 and engine instability were shortened by H 2 addition. • H 2 addition resulted in the reduced HC and CO emissions. • HBRE shares highly similar performance with HGRE. [ABSTRACT FROM AUTHOR]

The study aims to numerically investigate the combustion and emissions formation processes in a spark-ignition rotary engine fueled with hydrogen-gasoline blends. The Renormalization Group k-ε turbulence coupled with a skeletal primary reference fuel mechanism were adopted to simulate the engine working process under 0%, 2% and 4% hydrogen volume fractions in CONVERGE software. The flow field variation and detailed combustion processes were analyzed and discussed. Results showed that a mainstream flow field along with the rotor movement was formed during the compression stroke and sustained in the combustion chamber until the exhaust valve opening. The center of the burned zone would move in same direction with the mainstream flow. Meanwhile, due to the effect of the mainstream flow, the flame propagation in direction of the mainstream flow was expedited. While the flame propagation in contrary direction was retarded, consequently, the unburned mixtures at rear region of combustion chamber suffered incomplete combustion. The distributions of nitric oxide and carbon monoxide emissions were also dominantly affected by the flow field in the combustion chamber. After hydrogen addition, the increased OH, H and O radicals concentrations combined with the intense flow flied accelerated the combustion process, which resulted in the improvement and advancement of in-cylinder pressure and temperature. Compared with original gasoline case, the peak in-cylinder pressure was increased by 9.1% and 13.7% with 2% and 4% hydrogen blends, respectively. With hydrogen enrichment, the increased in-cylinder temperature promoted the formation of nitric oxide emission. Besides, Carbon monoxide emission was decreased with the increase of hydrogen addition fraction. [ABSTRACT FROM AUTHOR]

To investigate the property of the promising and eco-friendly hydrogen-fueled rotary engine, the effect of excess air ratio on the combustion and emission characteristic of it was explored by experiment. The test was conducted under 1500 rpm and 5 CAD ADTC ignition timing. The test results demonstrated that with the decrease of excess air ratio from 2 to 0.85, the thermal efficiency of the hydrogen-fueled rotary engine increases first and then decreases. Besides, increasing MAP is beneficial to improve thermal efficiency. Among the tested condition, the highest brake thermal efficiency is realized when the rotary engine operates at 1.4 excess air ratio and 88 kPa MAP, about 18.34%. And the excellent HC and NO emissions can be obtained at the highest efficiency point. Besides, with the decrease of excess air ratio and the increase of load, the stability and flame development period gradually decrease. With a decreased excess air ratio, the flame propagation period decrease first and then increases, whereas work capacity and thermal efficiency increase first and then decrease. For NO emission, it will increase sharply near the equivalent ratio and gradually decrease after rich combustion. Also, according to the analytical model, it is found that the power performance of the rotary engine depends on the trade-off relationship of in-cylinder pressure and its angle of action. • A rotary engine was modified to run on hydrogen. • The effects of excess air ratio on combustion and emission were studied. • The best efficiency is obtained when the excess air ratio equals 1.4. • An analytical model is presented and the reasonability also be proved. • The emission corresponding to the best efficiency point is excellent. [ABSTRACT FROM AUTHOR]

• The model of HFRE with active pre-chamber TJI was established. • The combustion characteristic of HFRE-SC was analyzed. • The optimum HIT and HID was obtained. Hydrogen can be used as fuel to replace gasoline, with the benefit of reducing harmful emissions of rotary engine (RE). The swirl chamber (SC) coupling spark plug and nozzle will achieve diffusion combustion and higher power as compared to the conventional spark plug. In the current work, a CFD model of a hydrogen-fueled rotary engine with swirl chamber (HFRE-SC) is established to study the impacts of hydrogen injection timing (HIT) and hydrogen injection duration (HID) on combustion characteristics of HFRE-SC. Results reveal that SC combustion system may achieve more combustion efficiency and higher indicated power when compared to port injection (PI). Moreover, lean hydrogen in the rear of combustion chamber (ROCC) can result from retarding HIT and extending HID. In addition, when the rich zone in SC moves toward the spark plug, making it difficult for flames to develop and spread. The best performance can be obtained when using the HIT at 75 °CA BTDC and the HID during 35 °CA, with an 8.42 % up in indicated power compared to the PI. [ABSTRACT FROM AUTHOR]

Using syngas as a primary fuel for internal combustion engines with spark ignition is a bridge technology for transitioning from carbon-based to hydrogen-based energy sources. There are two different ways of syngas delivery into combustion chamber: port injection or direct injection. In this study, the combination of these methods is considered for integration benefits of each injection technology and promotion of syngas utilization in rotary engines. In the novel concept of syngas dual injection, part of the fuel is delivered by a port injector during the induction stroke, while another part is directly injected during the compression stroke. The ratio of fuel mass delivered by port and direct injection is changed within the range of 0.0 (direct injection only) to 1.0 (port injection only) and chosen as a key parameter of concentration stratification. This study aims to investigate the optimal fuel injection strategy with numerical simulation of mixture formation, ignition, and combustion processes. It was shown that dual injection strongly influences turbulence intensity and mixture heterogeneity. The turbulence lengthscales generally increase with dual injection ratio growth. The direct injection case demonstrates maximum performance characteristics. However, the case with a small portion of directly injected fuel (10%–25%) increases fuel conversion efficiency by 5%–7% and decrease fuel consumption by 4%–6% with lower level of CO emission. The results show that the dual injection strategy provides flexibility in controlling the combustion process and emission reduction. • The dual injection strategy is an effective method of syngas utilization in a rotary engine. • The dual injection influences the mixture formation and combustion significantly. • Optimal fuel strategy is characterized by high homogeneity with advanced turbulence. • The major emission of the syngas-fueled rotary engine is carbon monoxide. [ABSTRACT FROM AUTHOR]

The present paper introduced an experiment survey focusing on exploring the impact of hydrogen enrichment on improving the lean-burn performance of an n-butanol rotary engine. During the test, the engine speed and intake pressure were roughly set at 4000 rpm and 35 kPa, respectively. A constant spark advance of 45 °CA was adopted through the test. Hydrogen volumetric fraction of the total intake was severally kept at 0% and 3%. The testing results manifested that the brake thermal efficiency and peak chamber temperature were heightened with hydrogen addition. Besides, the ignition delay and rapid combustion duration were both reduced with the hydrogen additive. Engine running stability gained an improvement by hydrogen supplement. Moreover, HC and CO emissions from the original n-butanol rotary engine were reduced after hydrogen adding. NOx emissions were increased with hydrogen enrichment while reduced with the increase of excess air ratio. This indicated that NOx emissions from both the n-butanol and hydrogen-blended n-butanol rotary engines could be reduced by lean combustion strategies. [ABSTRACT FROM AUTHOR]

Rotary engine has flat chamber and longs for fuel with high flame speed and small quenching distance. Hydrogen has many excellent characteristics that are suitable for the rotary engine. In this paper, the performance of a rotary engine fueled with pure hydrogen at different excess air ratios was experimentally investigated. The investigation was carried out on a single-rotor hydrogen-fueled rotary engine equipped with port fuel injection system. An online electronic control module was used to govern the hydrogen injection duration and excess air ratio. In this study, the engine was operating at the idle speed of 3000 rpm and different excess air ratios varied from 0.993 to 1.283. The test results demonstrated that the fuel energy flow rate of the hydrogen rotary engine and engine stability were reduced with the increase of excess air ratio. When the excess air ratio increased from 0.993 to 1.283, the hydrogen energy flow rate was decreased from 14.91 to 11.55 MJ/h. Both the flame development and propagation periods were increased with excess air ratio. CO emission was negligible, but HC, CO 2 and NOx emissions were still detected due to the evaporation and possible burning of the lubrication-used gasoline, and oxidation reaction of nitrogen of the intake air. [ABSTRACT FROM AUTHOR]

In this paper, a rotary engine equipped with an n-butanol and hydrogen port-injection system was developed to investigate the combustion and emissions characteristics of a hydrogen-blended n-butanol rotary engine at part load and stoichiometric conditions. A self-developed hybrid electronic control unit was adopted to adjust the injection durations of n-butanol and hydrogen. The rotary engine was run under the conditions of 4000 rpm, a manifold absolute pressure of 35 kPa and a fixed spark timing of 45 °CA before the top dead center during the whole testing operation. The hydrogen volumetric fraction in the total intake was varied from 0% to 6.30%. The test results manifested that the brake thermal efficiency and chamber temperature were simultaneously increased with hydrogen addition. The hydrogen supplement obviously shortened flame development and propagation periods. Both chamber pressure integral heat release fraction versus crank angle were increased when the hydrogen fraction was enhanced. HC emissions were reduced by 54.5% when hydrogen volume fraction was raised from 0% to 6.30%, CO and CO 2 emissions were also reduced after increasing hydrogen blending fraction. NOx emissions were mildly elevated due to the improved chamber temperature. [ABSTRACT FROM AUTHOR]

In the present paper, the cyclic variations of a hydrogen-blended gasoline rotary engine operated under various conditions were experimentally investigated. The experiments were carried out on a modified hydrogen-gasoline dual-fuel rotary engine equipped with an electronically-controlled fuel injection system. An electronic control module was specially made to command the fuel injection, excess air ratio and hydrogen volumetric fraction. The tested engine was first run at idle condition with a speed of 2400 rpm and then operated at 4500 rpm to investigate the cyclic variations of a hydrogen-enriched gasoline rotary engine under different hydrogen volumetric percentages in the total intake, excess air ratios and spark timings. The experimental results demonstrated that the coefficient of variations (in peak pressure, engine speed, flame development period and flame propagation period) of the gasoline rotary engine were distinctly decreased with the increase of hydrogen volume fraction under all the tested conditions. In particular, at idle and stoichiometric conditions, the coefficient of variation in CA0-10 and CA10-90 were reduced from 9.25% to 5.01%, 15.40% to 8.70%, respectively. [ABSTRACT FROM AUTHOR]

This paper presented an experimental study about the idle performance of a rotary engine fueled with hydrogen and gasoline blends. The idle speed was reduced from original 2400 to 2300 and 2200 rpm, and hydrogen energy percentage ( β H2 ) was varied from 0% to 35.0%. Test results showed that cyclic variation was raised with the decrease of idle speed whereas reduced with the increase of β H2 . Both decreasing idle speed and increasing β H2 were effective on reducing engine fuel consumption. Total fuel energy flow rate was effectively dropped from 22.4 MJ/h under “2400 rpm and β H2 = 0%” to 20.01 MJ/h under “2200 rpm and β H2 = 35.0%”. Combustion duration was reduced through increasing β H2 . HC and CO emissions were dropped with the increase of β H2 , but increased after reducing idle speed. CO 2 emission was decreased after reducing idle speed and adding hydrogen. [ABSTRACT FROM AUTHOR]

Because of the limit of properties of gasoline and irregular design of chamber, the pure gasoline rotary engine generally encounters partial burning, increased noxious emissions or even misfire at lean conditions. This situation could be deteriorated at idle because of the high variation in the intake charge and low combustion temperature. Hydrogen addition is proved to remit the deterioration of performance of sparked-ignited (SI) engines at idle and lean conditions. This paper conducted an experiment on a modified rotary engine equipped with gasoline and hydrogen port-injection systems to explore the performance of a hydrogen–gasoline rotary engine (HGRE) at idle and lean conditions. An electronic management unit (EMU) was invented to manage spark and fuel injection. Excess air ratio ( λ ) and hydrogen volumetric fraction in the total intake ( α H 2 ) were also governed through the EMU. For this study, the HGRE was operating at idle and α H 2 was kept at 0% and 3%, respectively. For a specific α H 2 , gasoline flow rate was reduced to make the HGRE run at desired λ . Results indicated that engine fluctuation and fuel energy flow rate were both decreased after hydrogen addition. Combustion duration was cut down and central heat release point was advanced after hydrogen addition. Peak chamber temperature ( T max ), pressure and heat release were enhanced after hydrogen blending. HC, CO and CO 2 emissions were simultaneously reduced because of hydrogen enrichment. Specifically, at λ = 1.00, HC, CO and CO 2 emissions were respectively reduced from 42,411 to 26,316 ppm, 1.86 to 0.78% and 9.96 to 8.58% when 3% hydrogen was added. [ABSTRACT FROM AUTHOR]

This study aims to explore the combined effect of injection angle and injection pressure in a gasoline direct injection rotary engine through numerical simulation. Simulation results show that with the increase of injection angle, the fuel impinging position changes from the rotor recess to the middle cylinder block. At the same injection angle, the fuel enrichment area turns to the front of the combustion chamber with the increase of injection pressure. The lower injection angle is helpful to obtain a more uniform fuel distribution. Especially, with increase of injection pressure, the in-cylinder inhomogeneity index presents a downward trend. Under different injection pressures, the flame propagation period of the 0° injection angle is the most stable. The stable flame development and propagation processes make it easy to obtain higher indicated thermal efficiency. The highest indicated thermal efficiency is obtained at 0° injection angle and 15 MPa injection pressure, which is up to 24.99%. Moreover, compared with the fuel intake port injection, part of direct injection strategies help to get higher in-cylinder peak pressure. The higher in-cylinder temperature promotes the formation of NOx, but the organization of the in-cylinder fuel distribution can effectively reduce CO and Soot emissions. • A rotary engine simulation model with gasoline direct injection was established and validated. • The combined effects of injection angle and injection pressure were investigated. • The lower injection angle can obtain higher in-cylinder pressure and indicated thermal efficiency. • Lower in-cylinder inhomogeneity index is helpful to reduce Soot and CO emissions. [ABSTRACT FROM AUTHOR]

• A rotary engine simulation model with gasoline port and direct injection was established and validated. • The combined effects of ignition position and injection method were investigated. • Higher in-cylinder pressure can be obtained by direct injection under the same ignition strategy. • Using double spark plugs ignition and port injection can reduce carbon-based emissions. This research aims to numerically investigate the combined effect of ignition position and injection method on the gasoline rotary engine. The three-dimensional dynamic model was established by CONVERGE software and validated by the experimental data. The results indicate that compared with port injection, the direct injection leads to obvious fuel stratification in the combustion chamber, and the local equivalence ratios around the two spark plugs are different. The index of in-cylinder fuel inhomogeneity corresponding to direct injection decreases linearly with the progress of the mixing process. Adopting the double spark plug can obtain a higher release heat rate and combustion efficiency than adopting the single spark plug ignition. Higher in-cylinder peak pressure and indicated thermal efficiency also can be obtained by using double spark plugs ignition. Only using leading spark plug ignition would cause a large in-cylinder unburned area, resulting in poor power performance of the rotary engine. In particular, the direct injection can obtain higher mean in-cylinder pressure than the port injection, but the indicated thermal efficiency of port injection is higher than that of direct injection. In the aspect of emissions, double spark plugs ignition would lead to higher in-cylinder temperature and NOx content than other ignition modes, but double spark plugs ignition can alleviate incomplete combustion and reduce HC emission. Under the same ignition strategy, the port injection can effectively reduce CO emission than direct injection. [ABSTRACT FROM AUTHOR]

• Hydrogen two-stage direct-injection is implemented on a gasoline SI rotary engine. • Injecting proper hydrogen in the second pulse after spark-ignition is investigated. • Two-stage injection strategies can realize desirable stratified conditions of hydrogen. • High thermal efficiency and good knock resistance are the benefits of the HTDI. • The HTDI allows significant CO and THC reduction with a slight NOx penalty rate. Hydrogen two-stage direct-injection enrichment is a novel injection strategy to utilize hydrogen more efficiently and effectively in gasoline rotary engines by inheriting the merits of hydrogen and direct injection simultaneously, such as flexible control, efficiency improvement, and emissions reduction. Based on the CONVERGE code with detailed chemistry solvers, a full-cycle CFD modeling including hydrogen jet-flow and combustion processes was presented and validated by experimental data. To understand the role of hydrogen two-stage injection in improving engine performance at part-load and lean-burn regime, six different injection arrangements for which two-stage injection strategies with variable hydrogen amount for each pulse (up to 30% for post-injection) had considered. The different effects on species evolution, combustion characteristics, knock propensity, and emissions formation were analyzed step-by-step. The simulation results showed that compared with direct-injected hydrogen for single-pulse, injecting adequate hydrogen in the second pulse after spark-ignition onwards performed a significant beneficial effect on the mixture stratification and flame propagation, especially for the trailing part of the rotor chamber, which contributed to the improvement in both combustion characteristics and thermal efficiency. The assessment of knock propensity demonstrated that the two-stage direct-injected hydrogen had the potential of mitigating the knock under lean operations. Using split injection accompanied by an optimized hydrogen allocation strategy allowed substantial unburned hydrocarbon and carbon monoxide reductions with a slight nitrogen oxide penalty rate due to the elevated combustion temperature. [ABSTRACT FROM AUTHOR]

To achieve more efficient and robust combustion, split direct-injected hydrogen as a new injection strategy for rotary engines was used to clarify the influences of various injection parameters, including hydrogen amount for each pulse, the dwell between pulses, and secondary injection pulse-width, on combustion performance and emissions formation by CFD modeling. The results of this investigation confirmed the benefit of split direct-injection as a useful means to govern mixture stratification which enabled the combustion more effective and rapid compared to single-injection mode. Enhanced combustion could be achieved by increasing the mass fraction of post-injection with an optimized dwell between injections. Further investigation on secondary injection pulse-width demonstrated that engine performance was substantially improved with a wider second injection pulse. From one side, as the secondary injection pulse-width was increased, the surrounding mixture distribution of the spark-plug location was richer, which was confirmed as a beneficial inhomogeneous circumstance of hydrogen to accelerate the burning rate. From another side, strong tumble level and turbulence intensity were of significant importance for facilitating the combustion process and getting optimal thermal efficiency. For emissions formation, split direct-injected hydrogen made a near-zero HC and CO emissions at the price of a comparable increase of NOx emissions. • Hydrogen split direct-injection is implemented on a gasoline SI Wankel engine. • Analyzing three factors for amelioration including first, post-injection, and dwell. • Split injection strategies can realize desirable stratified conditions of hydrogen. • Injecting proper hydrogen in each pulse with an adequate dwell is of importance. • Thermal efficiency can be notably improved benefits from the wide second injection. [ABSTRACT FROM AUTHOR]

• Implementation of oxygen enriched air on rotary engine combustion was performed. • Thorough 3D CFD models of rotary engines was built and verified by experiment data. • Increasing oxygen content stimulated the growth of initial flame and burned volume. • Oxygen enrichment markedly reduced the formations of CO, HC, and soot emissions. • The optimum combustion behavior can be achieved by α O2 = 30% and λ = 1.1 operation. The attractiveness of oxygen-enriched combustion advantages are making a comeback in the implementation of the rotary engine concept. In this connection, a numerical investigation on influences of intake oxygen enrichment combined with excess air ratio on combustion behavior of the rotary engine needs to be clarified. A three-dimensional computational fluid dynamics simulations coupling with chemical kinetic mechanisms was performed in this study, and the numerical results had been validated with existing experimental data. The species evolution, combustion characteristics, and pollutant formation were monitored to assess the oxygen-enriched combustion of the rotary engine. Results showed that there was a significant influence of intake oxygen enrichment for improving flame development and burned volume due to the reasonable species concentration and intense turbulence intensity. Increasing oxygen enrichment led to the enhanced peak pressure and advanced corresponding position, resulted in a rapid combustion period for improving heat-release efficiency and combustion efficiency, meanwhile made a higher indicated mean effective pressure at the price of a smaller increment of nitrogen oxide formation. The substantial reductions of carbon monoxide, unburned hydrocarbon, and soot were recorded, which is attributed to the higher-oxygen mixture with suitable lean operations. Considering combustion characteristics and emissions performance, the operation of intake oxygen volume of 30% accompanying the excess air ratio of 1.1 is the best choice for the engine used in the current study. [ABSTRACT FROM AUTHOR]