Search

A new topology for the design of microwave narrow band-pass filters (NBPFs) based on the alternate right–left handed transmission line (TL) concept is proposed. The proposed NBPF is a three-stage structure which two LH stages and one RH stage are used. The proposed LH stage is implemented by a spiral complementary split ring resonator (spiral CSRRs) and an interdigital capacitor while for implementing the RH stage, the conventional TL shorted by via and the spiral CSRR are used. The spiral CSRRs have been etched in the ground plane. To improve frequency selectivity and out-of-band rejection, the proposed RH stage has been cascaded with two LH stages. Accordingly, a compact NBPF is designed which exhibits extremely sharp rejection skirts around the target passband. The equivalent circuit model and full-wave simulation results of the proposed NBPF are developed. To validate the design concept, the designed filter has been fabricated and tested. Experimental verification is provided and a good agreement has been found between the simulation and measurement. The proposed NBPF has a passband covering 2.3–2.45 GHz and its measured 3-dB fractional bandwidth is about 7.5%. The total size of the proposed NBPF is 0.18 × 0.15 λg2. Compared with some other reported NBPFs, the presented NBPF has significant improvements on size reduction and selectivity. [ABSTRACT FROM AUTHOR]

In this paper, two miniaturized planar diplexers based on the substrate integrated waveguide (SIW) structure loaded by open complementary split-ring resonators (OCSRRs) are proposed. The working principle is based on the theory of evanescent mode propagation. The proposed SIW diplexers operate below the cutoff frequency of the waveguide. Both the complementary split-ring resonators (CSRRs) and the OCSRRs behave as electric dipoles however, the resonance frequency of the OCSRRs is approximately half of the resonance frequency of the CSRRs. Therefore, the electrical size o f the OCSRRs is larger than the CSRRs. Accordingly, the OCSRRs are more appropriate for the SIW miniaturization. At first, the filtering response of the SIW structure loaded by OCSRR unit cells is investigated. Then, two miniaturized SIW diplexers which consist of two cascaded OCSRR unit cells with different orientations are designed. For the first diplexer (Type I), the fractional bandwidths of operation for the up and down channels are 9.52 % and 2.59 % at 4.2 GHz and 5.8 GHz, respectively. For the second diplexer (Type II), the fractional bandwidths of operation for the up and down channels are 5.95 % and 2.51 % at 4.7 GHz and 5.6 GHz, respectively. Finally, in order to validate the ability of the proposed OCSRR unit cells in the size reduction, two designed diplexers are fabricated and experimental verifications are provided. A good agreement between the results of measurement and simulation is achieved. The proposed diplexers show significant advantages in terms of size reduction, low loss, high isolation, and integration with other planar circuits. [ABSTRACT FROM AUTHOR]

In this study, a reconfigurable triple‐band triple‐mode substrate integrated waveguide filter is designed and fabricated in the C‐band spectrum. A novel and simplified design procedure based on analytical equations is proposed. The filter design also benefits from a reconfigurable structure, using metallic via holes as perturbation, allowing wide‐band selectivity of the C‐band spectrum (from 4.4 to 6.9 GHz). Moreover, the filter benefits from a magnetic coupling solution between the resonators, which only couples the first three modes and rejects the next resonating modes. Therefore, a large bandgap in the spectrum is achieved. The proposed structure is fabricated and measured, and a high similarity between the simulation and fabrication is observed. The measured results show that the first band can be tuned in the frequency range of 4.4 to 7, the second band can be tuned in the range 5.8 to 7.7 GHz, and the third band from 5.8 to 7.7 GHz. The insertion loss 1.5 to 2.5 dB, 2 to 3 dB, and 2.5 to 3.5 dB for the first, second, and third bands, respectively. [ABSTRACT FROM AUTHOR]

In this paper, two ultracompact power dividers based on the substrate integrated waveguide (SIW) and half‐mode SIW (HMSIW) technologies loaded by complementary split‐ring resonators (CSRRs) are presented. The presented structures are designed based on the theory of evanescent mode propagation. To obtain a size reduction, the CSRR unit cells are etched on the metallic surface of the SIW and HMSIW structures. First, a two‐way HMSIW power divider is reported. In this circuit, the concept of HMSIW is utilized aiming at a further size reduction in addition to the size reduction by the CSRR unit cells. Then, a four‐way SIW power divider is designed so that the direct coaxial feed is used for the input port and microstrip transmission lines are used for the output ports. Both two‐way and four‐way SIW/HMSIW power dividers at 5.8 GHz covering WLAN are designed, fabricated, and measured. They respectively have 0.18 × 0.21 λg2 and 0.38 × 0.21 λg2 total size. A fair agreement between simulated and measured results is achieved. The measured insertion losses are 0.5 ± 0.5 and 0.6 ± 0.5 dB for the two‐way and four‐way SIW/HMSIW power dividers, respectively, in the operating band of interest. [ABSTRACT FROM AUTHOR]

A novel super compact filter based on half‐mode substrate‐integrated waveguide (HMSIW) technology loaded by the modified complementary split‐ring resonator (MCSRR) is proposed. The working principle of the proposed filter is based on the evanescent‐mode propagation technique. According to this technique, by loading the complementary split‐ring resonator (CSRR) on the metal surface of the substrate‐integrated waveguide (SIW) structure, an additional passband below the SIW cutoff frequency can be obtained. In order to miniaturize the physical size of the conventional CSRR, a new method is introduced. In the proposed MCSRR unit‐cell, the meander slots are carved inside all of the interior space of the ring. Accordingly, the length of the slot is increased which leads to an increase in the inductor and capacitor of the proposed structure without occupying the extra space. Therefore, the electrical size of the proposed MCSRR unit‐cell is reduced. Consequently, the resonance frequency of the proposed MCSRR unit‐cell is decreased compared to the conventional CSRR with the same sizes. Namely, the lower resonance frequencies can be achieved by using this technique without increasing the size of the unit‐cell. In order to confirm the miniaturization technique, two HMSIW filters loaded by the proposed MCSRR unit‐cell are designed, fabricated, and experimental verifications are provided. The results show that a miniaturization about 67% is achieved. [ABSTRACT FROM AUTHOR]

In this article, a new miniaturized metamaterial unit‐cell using stepped‐impedance resonator technique is proposed. The proposed unit‐cell is used to miniaturize the physical size of the conventional complementary split‐ring resonators (CSRRs). In the proposed unit‐cell which is called complementary G‐shaped resonator (CGR), the slot line in the conventional circular CSRR is replaced with the stepped‐impedance slot line. As well as, by carving two trapezoidal shapes inside the inner ring, the resonance frequency of the proposed CGR unit‐cell has been more decreased. Compared to the conventional circular CSRR structure, the electrical size of the proposed CGR is decreased and miniaturization is occurred. To investigate the performance of the proposed CGR unit‐cell in the size reduction, two substrate integrated waveguide filters and a diplexer are designed. To validate the proposed miniaturization technique, the designed filters and diplexer loaded by the CGR unit‐cell are fabricated and measured. The measured results are in a good agreement with the simulated ones. The results shows that, a miniaturization factor about 0.69 is achieved. [ABSTRACT FROM AUTHOR]