Search

This study was evaluated the tensile bond strength (TBS) of resin cements to bovine dentin resin-coated with all-in-one adhesive systems. Each of the dual-polymerizing resin cements; Link Max, Clearfil Esthetic Cement, Bistite II and Chemiace Ii were used to bond indirect resin disks to bovine dentin, as control, or coated by single-application or by dual-application of an adhesive system from the same manufacturer; G-Bond, Clearfil Tn-S Bond, Tokuyama Bond Force and Hybrid-Coat (n=10). After 24-hour water storage, TBSs were measured. The fracture pattern and the adhesive interface were observed using an SEM. Dual-application of the adhesive yielded significantly higher TBSs compared to control and single-application groups for all materials (p

Abstract: Objectives: To evaluate and compare bond strengths of different primers and resin cements to silica-based and zirconia ceramics. Methods: Silica-based and zirconia ceramic specimens were ground flat with #600-grit SiC paper. The ceramic surfaces were airborne-particle abraded and then divided into 11 groups of seven each: untreated (control); and conditioned with one of the six primers in combination with a resin cement from the same manufacturer as follows: Bistite II/Tokuso Ceramic Primer, Linkmax/GC Ceramic Primer, RelyX ARC/RelyX Ceramic Primer, Panavia F 2.0/Clearfil Ceramic Primer, and Resicem/Shofu Porcelain Primer and Resicem/AZ Primer. Stainless steel rods were bonded to the ceramic surfaces using one of the five resin cements. After 24-h water storage, the tensile bond strengths were tested using a universal testing machine and failure modes were examined. Results: Conditioning with primers containing a silane coupling agent (all the primers except AZ Primer) significantly enhanced bond strengths of resin cements to silica-based ceramic. For zirconia ceramic, Resicem/AZ Primer exhibited significantly higher bond strength than the other groups except Panavia F 2.0/Clearfil Ceramic Primer. The predominant failure mode of the groups conditioned with primers containing a phosphonic acid monomer (AZ Primer) or a phosphate ester monomer (Clearfil Ceramic Primer and Tokuso Ceramic Primer) was cohesive failure in cements whereas that with the other primers was adhesive failure at the zirconia surfaces. Significance: The use of primers containing a silane coupling agent improved resin bonding to silica-based ceramic. On the other hand, the use of primers containing a phosphonic acid monomer or a phosphate ester monomer improved resin bonding to zirconia ceramic. [Copyright &y& Elsevier]

Resin bonding to zirconia ceramic cannot be established by standard methods that are utilized for conventional silica-based dental ceramics. This study was aimed to examine the tensile bond strength of resin cement to zirconia ceramic using a new laboratory technique. Sixty-four zirconia ceramic specimens were air-abraded using Al2O3 particles and divided into two groups; the control group with no pretreatment (Control), and the group pretreated using the internal coating technique (INT), in which the surface of the zirconia specimens were thinly coated by fusing silica-based ceramic and air-abraded in the same manner. The specimens in each group were further divided into two subgroups according to the silane coupling agents applied; a mixture of dentin primer/silane coupling agent (Clearfil SE Bond Primer/Porcelain Bond Activator) or a newly developed single-component silane coupling agent (Clearfil Ceramic Primer). After bonding with dual-cured resin cement (Panavia F 2.0), they were stored in water for 24 h and half of them were additionally subjected to thermal cycling. The tensile bond strengths were tested using a universal testing machine. ANOVAs revealed significant influence of ceramic surface pretreatment (p<0.001), silane coupling agent (p<0.001) and thermal cycling (p<0.001); the INT coating technique significantly increased the bond strengths of resin cement to zirconia ceramic, whereas thermal cycling significantly decreased the bond strengths. The use of a single-component silane coupling agent demonstrated significantly higher bond strengths than that of a mixture of dentin primer/silane coupling agent. The internal coating of zirconia dental restorations with silica-based ceramic followed by silanization may be indicated in order to achieve better bonding for the clinical success. [ABSTRACT FROM AUTHOR]

This study was conducted to enhance the tensile bond strengths of resin cements to zirconia ceramics. Fifty-six zirconia ceramic specimens (Cercon Base) and twenty-eight silica-based ceramic specimens (GN-1, GN-1 Ceramic Block) were air-abraded using alumina. Thereafter, the zirconia ceramic specimens were divided into two subgroups of 28 each according to the surface pretreatment; no pretreatment (Zr); and the internal coating technique (INT). For INT, the surface of zirconia was coated by fusing silica-based ceramics (Cercon Ceram Kiss). Ceramic surfaces were conditioned with/without a silane coupling agent followed by bonding with one of two resin cements; Panavia F 2.0 (PF) and Superbond C&B (SB). After 24 hours storage in water, the tensile bond strengths were tested (n=7). For both PF and SB, silanization significantly improved the bond strength to GN-1 and INT (p<0.05). The INT coating followed by silanizaton demonstrated enhancement of bonding to zirconia ceramics. [ABSTRACT FROM AUTHOR]