Search

The improvement of recrystallization texture and magnetic properties in grain-oriented electrical steel with trace Bi addition processed by strip casting process was studied in this study. Low casting temperature and sufficient liquid steel flow during strip casting process enabled relatively homogeneous distribution of Bi in the as-cast strip, which accelerated the precipitation during solidification and cooling process. As a result, relatively high density of duplex MnS + AlN, MnS and AlN was formed at grain boundaries and inside grain. Due to the synergistic effect of continuous precipitation and fragmentation of coarse precipitates during cold rolling, the number density of precipitates was increased and mean size was decreased along the processing route. High density of precipitates is attributed to severe inhomogeneous plastic deformation, which promoted the formation of high density in-grain shear bands during cold rolling and recrystallization Goss texture during annealing. Homogeneous microstructure with average grain size of ~ 11.6 μm, strong Goss texture with intensity of 2.5 multiples of random distribution, fine precipitates with number density of ~ 1.9 × 109 /cm2 and mean size of ~ 49 nm were formed after primary recrystallization annealing. Furthermore, grain-oriented electrical steel with Bi addition experienced complete secondary recrystallization of exact Goss grains during high-temperature annealing, which is attributed to beneficial optimization of Goss texture and strong inhibition effect, and superior magnetic induction B8 of 1.91 T was obtained. It is expected that this study paves a new way for fabrication of high-performance grain-oriented electrical steel.

Grain-oriented silicon steel was produced by strip casting route. The effect of different annealing temperature on primary annealing and secondary annealing was investigated. The result showed that the average grain diameter increased and the grain uniformity was gradually destroyed with the increasing annealing temperature. Regardless of annealing temperature, the primary texture consisted of strong γ-fiber and weak λ-fiber. With the increase of annealing temperature, the γ-fiber intensity increased. In addition, the Goss component was not shown at 780-880 °C but appeared at 980 °C. After secondary annealing, complete abnormal grain growth occurred in all samples and the average grain diameter increased with the primary annealing temperature. The Goss sharpness of secondary grains firstly increased and then decreased with a peak value obtained at 830 °C. This result was explained in terms of the combination of the inhibiting force, primary grain diameter and primary texture.

We elucidate here the significance of cold rolling reduction on Luders band formation and mechanical behavior in cold-rolled intercritically annealed medium-Mn steel. The study indicated that Luders strain can be decreased by decreasing cold rolling reduction. Moreover, inactive recovery and recrystallization of ferrite consisting of a high dislocation density was responsible for the presence of low Luders strain.

The Nb-bearing grain-oriented silicon steel sheets were produced by conventional route and novel twin-roll casting route, respectively. The microstructure, texture and precipitate evolution were comparatively investigated by using electron backscattered diffraction (EBSD) and transmission electron microscope (TEM). The findings revealed that the precipitation behavior and the texture evolution were totally different between the two processing routes. In the conventional route, a great number of nanoscale niobium nitride particles (NbN), which acted as mainly grain growth inhibitors were precipitated during hot rolling, while in the twin-roll casting route, due to the rapid solidification, the precipitation of NbN were suppressed and a new type Nb-bearing precipitate enriched with sulfur element was observed in the as-cast strip. Besides, the primary recrystallized texture of conventional specimens was characterized by strong &gamma, fiber with a peak at {111} &lt, 110&gt, together with very few Goss components. While in the case of twin-roll casting specimens, the strongest primary recrystallized texture was {111} &lt, 112&gt, texture and the area fraction of Goss component was much higher than that of conventional specimens. After final high temperature annealing, complete secondary recrystallization was obtained in twin-roll casting specimens and the magnetic induction of B8 was 0.1 T higher than that of conventional specimens.

Grain-oriented silicon steels were produced by the shortest processing route involving twin-roll strip casting, two-stage cold rolling with intermediate annealing, and simulated continuous annealing. The secondary recrystallization behavior of grain-oriented silicon steels under different inhibition conditions was in-situ observed by combining the confocal laser scanning microscopy (CLSM) and electron backscattered diffraction (EBSD) techniques. The results revealed that the optimal temperature of secondary recrystallization showed a proportional relationship with the Zenner pinning force. In the case of weak pinning force, the abnormal grain growth occurred quickly at ~1050 &deg, C. The corresponding growth rates were in the range of 60&ndash, 1400 &mu, m/min and decreased gradually as the secondary recrystallization proceeded. In the case of strong pinning force, the incubation time and onset temperature of the secondary recrystallization was significantly increased, but the total time of the secondary recrystallization was obviously shortened from 685 s to 479 s, and the final magnetic induction of B8 was increased from 1.7 T to 1.85 T. After the secondary annealing, some island grains and coarse primary grains were retained. The formation of island grain was related to the low migration of grain boundaries. The findings of coarse &gamma, grains indicated that the primary grain size also played a crucial role during secondary recrystallization, apart from the primary recrystallized texture, which attracted more attention previously.

Thin-gauge non-oriented silicon steel with high strength was successfully processed using strip casting. Texture evolution and strengthening mechanism via nanoscale Cu-rich precipitates were studied to fundamentally understand the balanced combination of magnetic properties and mechanical properties. Coarse equiaxed grains with average size of ∼190 μm and relatively random texture were formed in the as-cast strip, which contributed to the inhomogeneous deformation, resulting in high density of shear bands. Exact Cube was retained from the initial Cube texture and new Goss was formed during the heavy rolling process in the 0.20 mm cold rolled sheet, which promoted relatively strong Cube and Goss texture after recrystallization annealing. The 0.20 mm annealed sheet exhibited high magnetic induction of 1.709 T, which corresponds to the high texture factor of 0.5. The total iron losses were significantly reduced with decrease in thickness, and the P1.5/50, P1.0/400, and P1.0/1000 in 0.20 mm sheet were as low as 2.63, 15.17 and 55.63 W/kg, respectively, which showed a good match between magnetic induction and iron loss. During the aging process, both the magnetic induction and total iron loss exhibited relatively good stability. With increase in aging time, the yield strength first rapidly increased and then slightly decreased. In 0.20 mm sheet, peak yield strength of ∼630 MPa was obtained on aging at 550 °C for 90–120 min. The key mechanism of precipitation strengthening was attributed to the difference in modulus and coherency strain associated with high density of nanoscale precipitates of ∼5 nm. The study revealed that the nanoscale Cu-rich precipitates can be adopted as effective approach to increase the yield strength over ∼100 MPa without deteriorating iron loss in thin-gauge non-oriented silicon steel by strip casting, which guaranteed the balance of magnetic properties and mechanical properties to meet the requirements of high-speed motor.

The present study focuses on improving the magnetic properties and decreasing the anisotropy in non-oriented electrical steel by optimizing {1 0 0} recrystallization texture. As-cast Fe-1.3%Si strip with {1 0 0} texture produced by strip casting was subjected to hot rolling in the ferrite region, cold rolling, and recrystallization annealing. Magnetic properties and texture evolution after different stages of processing were studied. Annealed sample without hot rolling exhibited pronounced Cube and Goss texture, which led to high permeability but induced a large difference (∼0.15 T) in magnetic induction B50 between the maximum at 0° and minimum at 45° to the rolling direction. The introduction of hot rolling with 17–40% reduction weakened the intensity of recrystallization texture and had small influence on the nature of texture and magnetic induction. However, relatively complete {1 0 0} recrystallization texture was developed in the sample with hot rolling of 55% reduction. On the other hand, the average grain size of annealed sheets gradually increased with the increased hot rolling reduction. As a result, the magnetic induction and the core loss was optimized together with the improvement of anisotropy. The development of recrystallization texture is discussed on the basis of the deformed microstructure and nucleation mechanism, while the magnetic properties are correlated to the magnetic quality of the texture.

The primary annealed sheets of strip-cast grain-oriented silicon steel were isothermally secondary annealed for 15 min under 100% H2 atmosphere. The microstructure and crystallographic orientation at different annealing temperatures were characterized and the secondary recrystallization behavior was elucidated. It was observed that relatively complete abnormal grain growth occurred at 1025 °C. Incomplete abnormal grain growth developed when the temperature was lower than 1025 °C, and normal grain growth occurred when the temperature was higher than 1025 °C. During the abnormal grain growth, both of the Goss and {110}⟨227⟩ grains developed because of the rapid decrease of the inhibiting force and the limited annealing time. Considering the high energy boundary (HE), coincidence site lattice boundary (CSL) and solid-state wetting (SSW) models for abnormal grain growth, the first one explained the development of the Goss and {110}⟨227⟩ grains. Another result was that several matrix grain colonies were observed in the interior or at the boundaries of secondary grains after abnormal grain growth. The grains at the periphery of these colonies showed a large fraction of high energy boundaries (20–45° misorientation) with the surrounding secondary grain and similar grain size with the unconsumed matrix grains. Therefore, these colonies were expected to be consumed by prolonging the annealing time and thus the limited annealing time was responsible for their occurrence. A possible explanation for the dominated high energy boundaries instead of low energy boundaries at the periphery of these colonies was proposed. All of these behaviors promoted the understanding of abnormal grain growth.

A 3.1 mm thick non-oriented Fe-1.0% Si steel as-cast strip was produced by twin-roll strip casting. Samples with/without strip annealing were cold rolled to 0.5 mm and then annealed. The development of microstructure, precipitate and texture was characterized along the entire processing route. It was found that annealing after strip casting had a minor influence on the average grain size and texture of the as-cast strip. A large number of particles precipitated and coarsened during the strip annealing process. Meanwhile, precipitates hindered dislocation slip and crystal rotation such that more significant in-grain shear bands were formed in cold rolled sheets. During recrystallization annealing process, the newly formed fine precipitates in directly cold-rolled sheets consumed stored strain energy and also hindered grain growth. But the initial precipitates in the annealed strip grew further and the effect of pinning of dislocations and grain boundary was lost. Therefore, annealed sheets with strip annealing process showed homogeneous equiaxed grains and the recrystallization texture was characterized by strong λ-fiber texture, which led to high permeability.

The effect of rolling temperature on the evolution of microstructure, texture, and magnetic properties of ultra-low-carbon grain-oriented silicon steel was studied in strip-casting process. Dynamic strain-aging (DSA) behavior was observed during warm rolling in the temperature range of ~ 200 to 400 °C based on the fact that majority of the inhibitor elements remained in solution during the strip-casting process. Considering the initial coarse grains with strong {100} fiber prior to rolling, the cold-rolled specimen exhibited pronounced α-fiber and weak γ-fiber texture. However, intense shear bands and high stored energy regardless of the orientation were obtained in the warm-rolled specimens at the DSA temperature, accompanied by weak α-fiber and strong γ-fiber texture. While homogenous microstructure with lower stored energy was observed in the case of high temperature, the differences in shear bands and stored energy governed by the rolling temperature were strongly related to the extent of DSA effect, which is attributed to distinct characteristic of rolling and recrystallization texture. After recrystallization annealing, fine-grained homogeneous microstructure with strong Goss and γ-fiber texture was obtained at the DSA temperature, while relatively random texture with much more α-fiber and θ-fiber components was observed in the case of high temperature. The microstructure and texture of primary annealed sheets exhibited sufficient Goss grains and favorable surrounding matrix with pronounced γ-fiber texture, which was responsible for the perfect secondary recrystallization annealing in the warm-rolled specimens at the DSA temperature. The present study suggests that texture optimization of strip-cast grain-oriented silicon steel can be achieved by warm rolling in the appropriate temperature range, with improved magnetic properties.

The shear-compression deformation of GH4169 superalloy at 1000–1200 °C and 0.01–1 s−1 was investigated by physical and numerical simulation based on a specific shear-compression sample (SCS). OM, EBSD, and TEM analysis revealed the three typical regions in SCS. Dynamic recrystallization (DRX) preferred to occur in the slot region due to the strain concentration, where the Mises equivalent strain was about 4–6 times higher than the pre-set ones. Mixed grains were observed in the transition region because of insufficient deformation. In contrast, equiaxial grains were preserved in the cylindrical region with negligible deformation. Experimental stress decreased with the increase of temperature and decrease of strain rate. The maximum stress was 180 MPa, which was only 30% of that under single compression deformation. Furthermore, four DRX mechanisms were observed in GH4169. Discontinuous dynamic recrystallization (DDRX) and continuous dynamic recrystallization (CDRX) were the dominant and auxiliary mechanisms, respectively. Twinning dynamic recrystallization (TDRX) occurred in the annealing twins with a fast nucleation rate, and the intersected nano-twins provided favorable nucleation sites for DRX. Lastly, secondary dynamic recrystallization (SDRX) with unique nucleation mechanism of triangularly intersecting subgrain boundaries emerged in SCS, which nucleated in the DRX grains and further refined the microstructure of GH4169.

A novel processing route involving strip casting, pre-annealing treatment, cold rolling and recrystallization annealing was applied to a Fe-2.6%Si steel to improve the magnetic properties. The impact of as-cast strip pre-annealing on the microstructure, texture, precipitation and magnetic properties were investigated by electron probe micro-analysis, transmission electron microscopy, and X-ray diffraction analysis, etc. It was found that the precipitation of second-phase particles during strip casting was restrained by rapid solidification. The absence of pre-annealing led to the occurrence of a large amount of 20–50 nm MnS precipitates in the final annealed sheets, which is responsible for fine grains and high core loss (4.01 W/kg) due to grain boundary pinning effect. Although the microstructure and texture of 900–1000 °C pre-annealed samples were similar to those of as-cast strip, significant grain coarsening together with the strengthening of λ-fiber texture was observed in the 1100 °C pre-annealed strips. In comparison with the case of as-cast strip, a higher amount of large-sized precipitates consisting of manganese sulfide and/or aluminum nitride occurred in matrix after pre-annealing. Correspondingly, in the final annealed sheets, the number density of precipitates with sizes smaller than 100 nm was substantially reduced, and 100–200 nm and 200–500 nm sized particles became more dominant in samples subjected to 30-min and 120-min pre-annealing treatments respectively. In addition, the average grain size of final annealed sheets increased with the pre-annealing temperature and time because of the weakened pining effect of coarsen precipitates. Ultimately, the magnetic induction of samples subjected to pre-annealing was slightly increased and ranged from 1.73 T to 1.75 T owing to the enhancement of {100} recrystallization texture, and simultaneously the core loss significantly decreased until a minimum of 3.26 W/kg was reached. Nevertheless, large number of 200–500 nm particles presented during pre-annealing for 120 min could weaken the improvement in core loss which is likely associated with the pinning effect on magnetic domain wall.

Texture optimization has always been a challenge to fabricate non-oriented electrical steels (NOES). In the present study, thin-gauge NOES with high permeability was successfully processed using an innovative and convenient twin-roll strip casting process without hot rolling. The relation between the as-cast microstructure, processing route and texture evolution was studied. The results indicated that as-cast strip with coarse grains exhibited strong {100}〈0vw〉 texture and unique {110}〈110〉 component. Annealed sheets processed by one-stage rolling displayed pronounced {111}〈112〉, {223}〈110〉 components and weak Cube and Goss texture. Micro-texture characteristics revealed that {100}〈0vw〉 texture was partially retained from initial grains, and new Cube and Goss substructures were generated within {110}〈110〉 deformed grains during cold rolling. This was responsible for the development of Cube and Goss recrystallization texture. Furthermore, the application of two-stage rolling not only reinforced these two behavior, but also accelerated the nucleation of η grains because of the increased shear bands in cold-rolled sheets. In this manner, an improved texture consisting of dominant η-fiber, weak γ-fiber and optimized magnetic properties (B50 = 1.72 T, P10/400 = 14.91 W/kg) were obtained. Keywords: Thin-gauge non-oriented electrical steel, Twin-roll strip casting, Microstructure, Texture, Magnetic properties

We elucidate here the impact of niobium in ultra-low carbon grain oriented electrical steel (GOES) in terms of microstructure, texture, precipitation and magnetic properties that was processed by twin roll strip casting. Coarse and complex MnS + NbN precipitates, and fine NbN were nucleated at the grain boundaries and in the interior of the grain in the as-cast strip, which contributed to a small degree of grain refinement together with relatively random texture, and AlN precipitation was suppressed during the strip casting process. NbN continuously precipitated during the entire process and exhibited high stability during the reheating cycle, which provided stronger inhibiting force in comparison to AlN precipitates. As a consequence, fine and homogeneous inhibitors were obtained in the primary annealed sheet in the presence of Nb under cold rolling and annealing parameters used in the present study. On considering the effect of NbN particles or Nb in solution on the deformation and recrystallization behavior, the primary annealed Nb-containing sheet exhibited significantly more homogeneous microstructure in relation to Nb-free GOES, with grain size in the range of ∼8–12 μm, and was characterized by relatively more pronounced γ-fiber and weak Goss texture, beneficial for the abnormal growth of Goss grains. Furthermore, Nb-containing GOES experienced complete abnormal growth during secondary recrystallization annealing, such that the enhanced magnetic induction (B 8 as high as 1.88 T) was obtained. In summary, the present study underscores that NbN can be used as an effective inhibitor in ultra-low carbon grain oriented electrical steel using strip casting technology.

Ultra-thin grain-oriented silicon steels were processed via the conventional process and strip casting process, and the mechanisms of texture inheritance and inhibitor induced secondary recrystallization were comparatively studied in detail. In the conventional route with commercial grain-oriented silicon steel as the starting material, exact {1 1 1} 〈1 1 2〉 dominated the deformation texture after cold rolling with ~ 63% reduction, and strong Goss texture was formed in 0.08–0.10 mm thin-gauge primary recrystallized sheet. Meanwhile, weak {2 1 0} 〈0 0 1〉 and {h11} textures were also observed because of the inhomogeneous deformation with initial deviated Goss texture. After high temperature annealing, the sheet experienced incomplete secondary recrystallization with abnormal growth of Goss grains accompanied by normal growth of {2 1 0} 〈0 0 1〉 and {4 1 1} 〈1 4 8〉 grains, considering the absence of pinning force on grain boundary migration. In the strip casting process, the intensity of γ-fiber texture was increased, while grain size decreased from ~ 13.3 to ~11.4 μm and the area fraction of Goss grains decreased from 2.8% to 0.6% in the primary recrystallized sheet with decrease of thickness from 0.15 to 0.08 mm. During high temperature annealing process, MnS, (Nb,V)N and AlN provided continuous and sufficient inhibition force for normal grain growth, which guaranteed the formation of complete secondary recrystallization of exact Goss grains. Superior magnetic induction B8 was up to 1.97 T in the strip casting process, which was 0.09 T higher than the conventional route. Meanwhile, the iron losses P1.7/50 and P1.0/1000 were as low as 0.85 and 20.7 W/kg, respectively, which were comparable to the reported ultra-thin grain-oriented silicon steels. The present study provided a novel method to produce high efficiency ultra-thin grain-oriented silicon steel, which may significantly contribute to energy saving in high-frequency electrical devices.

In order to improve the mechanical properties of Inconel 718 alloy produced by sub-rapid solidification, the yttrium (Y) element was added during casting. One alloy with 0.1% weight Y content (0.1Y) and a reference alloy without Y addition (0Y) were produced, which involved homogenization, cold rolling, intermediate annealing, and aging treatment. The influences of Y addition on the microstructure and mechanical properties of Inconel 718 alloy were examined. Due to the precipitation of Ni3Y and Ni17Y2 particles, 0.1Y alloy exhibited a refined grain size and a lower recrystallization fraction. The average grain size of 0Y homogenized sample and 0.1Y homogenized sample were about 50.8 μm and 29.5 μm, respectively. Besides, a higher fraction of δ phase precipitated in the 0.1Y annealed sample, including a large amount of granular or short-rod shape δ phases and a small amount of needle-like δ phases. The area fraction of δ phase in the 0.1Y annealed sample was ~10.45%. However, the area fraction of δ phase in the 0Y annealed sample was lower (~7.93%), and needle-like δ phase was hardly observed under this condition. Compared with 0Y alloy, 0.1Y alloy showed better tensile properties. The 0.1Y alloy after aging treatment exhibited an excellent combination of ultimate tensile strength (~1400 MPa), and total elongation (~20%) when deformed at room temperature.

An unconventional cold rolling scheme (inclined rolling at 0°, 30°, 45°, 90° during second-stage cold rolling process) was adopted to process grain-oriented silicon steel based on strip casting process. The influences of inclination angles on microstructure, texture, inhibitor and magnetic properties were studied by a combination of EBSD, XRD and TEM. It was found that the α-fiber texture was weakened and γ-fiber was strengthened in cold rolled sheet with increase in inclination angle. The primary recrystallization sheet exhibited more homogeneous microstructure with relatively strong γ-fiber, medium α-fiber texture, weak λ-fiber texture and Goss component at high inclination angles. Fine and homogeneous inhibitors were obtained after primary annealing with increase in inclination angle from 0° to 90° because of more uniform deformation after inclined rolling. The grain-oriented silicon steel experienced completely secondary recrystallization at various inclination angles after final annealing process, with superior magnetic properties at 0° and 90°. Furthermore, Goss nuclei capable of final secondary recrystallization in strip casting process newly formed both in-grain shear bands and grain boundaries region during second-stage cold rolling and subsequent annealing process, which is different from the well-accepted results that Goss texture originated from the subsurface layer of the hot rolled sheet or during intermediate annealing process. In addition, the Goss texture that nucleated in-grain shear bands was weaker but more accurate as compared to that in grain boundaries region.

A Fe-3.0%Si non-oriented silicon steel was produced by a novel strip casting process. Cold-rolled sheets were annealed at temperatures varying from 900 to 1200 ° C with the aim to investigate the influence of recrystallization annealing process on the microstructure, texture and magnetic properties. The increase in annealing temperature significantly increased the recrystallized grain size and reduced the core loss. However, the oversized microstructure (~360 μm) in 1200 ° C annealed sheets resulted in an augment in core loss. In addition, with increasing annealing temperature, the magnetic induction diminished along the rolling direction while gradually increased along the transverse direction, even though the average value changed slightly. This interesting result could be attributed to the weakening in η -fiber and strengthening in λ -fiber and γ -fiber texture. The best combination of core loss (3.23 W/kg), magnetic induction (1.71 T) and anisotropy was obtained at recrystallization annealing of 1100 ° C. The specified and unspecified errors in this paper have been carefully corrected, and

A novel ultra-low carbon grain oriented silicon steel was successfully produced by strip casting and two-stage cold rolling method. The microstructure, texture and precipitate evolution under different first cold rolling reduction were investigated. It was shown that the as-cast strip was mainly composed of equiaxed grains and characterized by very weak Goss texture ({110} ) and λ-fiber ( //ND). The coarse sulfides of size ~100 nm were precipitated at grain boundaries during strip casting, while nitrides remained in solution in the as-cast strip and the fine AlN particles of size ~20–50 nm, which were used as grain growth inhibitors, were formed in intermediate annealed sheet after first cold rolling. In addition, the suitable Goss nuclei for secondary recrystallization were also formed during intermediate annealing, which is totally different from the conventional process that the Goss nuclei originated in the subsurface layer of the hot rolled sheet. Furthermore, the number of AlN inhibitors and the intensity of desirable Goss texture increased with increasing first cold rolling reduction. After secondary recrystallization annealing, very large grains of size ~10–40 mm were formed and the final magnetic induction, B 8 , was as high as 1.9 T.

Thin gauge grain-oriented (GO) silicon steel with high permeability was successfully processed by a simple way based on strip casting process, without hot rolling and decarburization annealing. The primary annealed sheet exhibited unique characteristics of homogeneous precipitation because of near-rapid solidification, and fine-grained recrystallized microstructure with relatively strong Goss texture and pronounced {111} 〈112〉 texture, which was responsible for the subsequent Goss abnormal growth. MnS, (Nb,V)N and AlN precipitates provided strong pinning effect on grain boundaries at different stages during the final annealing process, which is referred as “sequential inhibition behavior”. The thin gauge GO silicon steel experienced complete secondary recrystallization induced by inhibitor, and exhibited sharp Goss texture together with significantly superior magnetic properties (magnetic induction B8 = 1.98 T; iron loss P1.7/50 = 0.7 W/kg). Keywords: Thin gauge grain oriented silicon steel, Strip casting, Magnetic properties, Microstructure, Precipitation, Secondary recrystallization

A Fe-1.3% Si non-oriented silicon steel strip was produced by twin-roll strip casting process, and subsequently treated with cold rolling and annealing. The effect of heating rates on the recrystallization and precipitation behavior of second phase particles (AlN and MnS) was investigated by MMS-200 thermal mechanical simulator. It was found that the recrystallization area fraction decreased obviously with the increase of heating rate. At the heating rate of 5 °C/s, the recrystallization rate gradually decreased with the extension of holding time, but it increased at the rapid heating rates. The particle’s sizes mainly concentrated in 50~200 nm at the heating rate of 5 °C/s during annealing. The number of particles under 50nm increased gradually and the number of precipitates between 50~400 nm reduced significantly when the heating rate was increased to 50~300 °C/s. The results indicated that the rapid heating rate could refine the size of precipitates and decrease the number of particles above 50nm.

Grain-oriented 4.5 wt% Si and 6.5 wt% Si steels were produced by strip casting, warm rolling, cold rolling, primary annealing, and secondary annealing. Goss grains were sufficiently developed and covered the entire surface of the secondary recrystallized sheets. The microstructure and texture was characterized by OM, EBSD, TEM, and XRD. It was observed that after rolling at 700 °C, the 6.5 wt% Si steel exhibited a considerable degree of shear bands, whereas the 4.5 wt% Si steel indicated their rare presence. After primary annealing, completely equiaxed grains showing strong γ-fiber texture were presented in both alloys. By comparison, the 6.5 wt% Si steel showed smaller grain size and few favorable Goss grains. Additionally, a higher density of fine precipitates were exhibited in the 6.5 wt% Si steel, leading to a ~30-s delay in primary recrystallization. During secondary annealing, abnormal grain growth of the 6.5 wt% Si steel occurred at higher temperature compared to the 4.5 wt% Si steel, and the final grain size of the 6.5 wt% Si steel was greater. The magnetic induction B 8 of the 4.5 wt% Si and the 6.5 wt% Si steels was 1.75 and 1.76 T, respectively, and the high-frequency core losses were significantly improved in comparison with the non-oriented high silicon steel.

The mechanism responsible for secondary recrystallization is still disputed in grain oriented silicon steel. This is mainly related to the complexly of itself. In this work, the occurrence of {2 1 0} texture through secondary recrystallization was observed in the grain oriented silicon steel with Cu 2 S as main inhibitor. In order to elucidate the abnormal growth of {2 1 0} grain, texture evolutions in Fe–3% Si–0.5% Cu steel were investigated using micro-texture analysis. In addition, the {2 1 0} texture was used to validate the current mechanisms of secondary recrystallization. The result indicates that the surface energy plays a significant role in the selection of secondary recrystallization besides the characteristics boundaries which are linked to high mobility.

An ultra-low carbon Fe–3%Si grain oriented electrical steel strip was produced by a twin roll strip casting process. Next, the strip with or without annealing was cold rolled and subsequently annealed. The effect of annealing after strip casting on the texture development was studied using macro-/micro texture analysis. Due to the rapid solidification, the precipitation behavior of second phase particles was suppressed and very few particles were observed in the as-cast strip. The direct cold rolled texture was characterized by strong α ( //RD) and weak γ ({111}//ND) fibers. While, in the annealed strip, a large number of particles were precipitated during the annealing of the cast strip and these particles hindered the crystal rotation during cold rolling such that part of the initial solidification texture remained in the cold rolled sheet. In the case of the direct cold rolling process, the precipitation occurred before recrystallization during primary annealing. These fine particles had a significant pinning effect on dislocations and further retarded the recrystallization behavior, leading to relatively strong α-fiber in the primary annealed sheet. On the other hand, compared with the fine and dispersed particles precipitated during the strip annealing process, the distribution of particles precipitated during primary annealing were inhomogeneous. Therefore, there was no secondary recrystallization during secondary annealing, which was distinct from the strip annealing process where abnormal growth of Goss grains were observed and the magnetic properties were significantly improved.

Non-oriented electrical steel as-cast strip was produced by twin roll strip casting process, and subsequently cold rolled and annealed at heating rates in the range of 3–450 °C/s with the aim to elucidate the effect of heating rate on the evolution of recrystallized microstructure and texture. The average grain size was rapidly increased when the heating rate was increased from 3 to 25 °C/s, and decreased when the heating rate was greater than 25 °C/s. The average grain size did not increase linearly with heating rate, which was related to different degree of nucleation and growth rate. The recrystallization texture exhibited pronounced improvement during rapid annealing. At high heating rate, the Goss and Cube had a higher probability of nucleation of shear bands with high stored energy, while the intensity of the γ-fiber texture was significantly reduced. The highest B50 value attained was 1.803 T at a heating rate of 300 °C/s. The study indicates that rapid heating has strong effect on the recrystallization behavior in non-oriented electrical steels, which facilitates optimization of microstructure and texture, especially in the coarse-grained structure.

Grain oriented silicon steel was produced by strip casting and two-stage cold rolling processes. The development of microstructure and texture was investigated by using optical microscopy, X-ray diffraction and electron backscattered diffraction. It is shown that the microstructure and texture evolutions of strip casting grain oriented silicon steel are significantly distinct from those in the conventional processing route. The as-cast strip is composed of coarse solidification grains and characterized by pronounced 〈001〉//ND texture together with very weak Goss texture. The initial coarse microstructure enhances {111} shear bands formation during the first cold rolling and then leads to the homogeneously distributed Goss grains through the thickness of intermediate annealed sheet. After the secondary cold rolling and primary annealing, strong γ fiber texture with a peak at {111}〈112〉 dominates the primary recrystallization texture, which is beneficial to the abnormal growth of Goss grain during the subsequent high temperature annealing. Therefore, the secondary recrystallization of Goss orientation evolves completely after the high temperature annealing and the grain oriented silicon steel with a good magnetic properties ( B 8 =1.94 T, P 1.7/50 =1.3 W/kg) can be prepared.

Texture evolution in Fe-1.3%Si steels with ultra-high magnetic induction produced by strip casting, cold rolling and annealing was investigated using macro-/micro-texture analysis. A new and strong {1 1 0} fiber has been founded in thin as-cast sheets. The in-grain shear bands with the Cube orientation can be observed in deformed {1 1 0}〈1 1 0〉 grains after cold rolling. The new Cube grains are mainly nucleated and grow within those shear bands at the beginning of recrystallization and consequently determine the overall annealing texture.

In conventional production of grain-oriented electrical steel, the content of silicon is limited to 3.0%~3.4%, which could control the ‘γ→α’ transformation process to obtain fine grain sizes in hot-rolling and disperse AlN particles in normalizing. In this study, the precipitation behaviors of S ans N in 4.5% Si-Fe alloy are inhibited during twin-roll strip casting process. And then the ideal microstructure and texture was obtained after the two-stage cold rolling and primary annealing. The evolution of microstructure and texture during the subsequent high temperature annealing were investigated. The results revealed that a sharp and developed Goss texture has been achieved by secondary recrystallization in the final annealing step and the magnetic induction B8 /Bsis above 1.76/1.90T.

The grain oriented silicon steel containing 3%Si-0.5%Cu was produced by low slab reheating temperature technique. The precipitates were observed during the mainly process such as hot rolling, normalization, primary and secondary recrystallization annealing. The species, size, density and shape of precipitates were identified using TEM technique. The results indicate that Cu2S and AlN are mainly inhibitors which precipitate during hot rolling and normalization respectively. After primary recrystallization annealing the precipitation size of Cu2S is in the range of 30~40nm while the mean size of AlN is ~50nm, which could inhibit grain growth. In addition, the precipitation of MnS is inhibited comparing with the precipitation of Cu2S.

Grain-oriented 4.5%Si steel is processed by strip casting and two-stage rolling with second rolling reduction varied from 53.3 to 82.7%. The microstructure and texture evolution are studied with emphasis on the effect of second rolling reduction on secondary recrystallization. After secondary annealing, significant abnormal grain growth occurs for all reductions in the range of 53.3–82.7%. The underlying reason is the strong inhibiting force induced by additional Nb, and the grain diameter of the secondary grains increase with increased rolling reduction. Additionally, the sharpness of secondary grains to ideal Goss orientation increase with increase in second rolling reduction. This is attributed to decreased inhibiting force drop rate between abnormal grain growth of precise Goss and deviated Goss grains with increased rolling reduction. Another interesting aspect is enhancement of magnetic induction B8 and significant reduction in high frequency (400–1000 Hz) core losses with increase in second rolling reduction. Optimal magnetic properties are obtained in the steel subjected to 82.7% rolling reduction. The present study suggests that strip casting is an effective approach to fabricate grain-oriented high silicon steel, especially thin-gauged steels with superior magnetic properties.

Here, the authors elucidate the microstructure and texture evolution in ultra-low carbon grain oriented silicon steels with (Cu,Mn)S and Nb(C,N) as inhibitors. Both Cu- and Nb-bearing steels exhibit microstructural and texture gradients across the thickness. The surface layer is characterized by recrystallized equiaxed grains, while the subsurface layer is dominated by strong Goss texture, and the center layer is composed of elongated deformed bands with strong α-fiber including {100} ∼{223} texture. In contrast to the Cu-bearing hot rolled sheet, the deformed center zone of Nb-hot rolled sheet is broadened and indicate a new {111} component, while the neighboring Goss zone, which act as the nuclei for secondary recrystallization is reduced. Also, the fraction of Goss texture in Nb-primary recrystallized sheets is lower than Cu-primary sheets in a series of specimens subjected to identical annealing temperature prior to secondary recrystallization because of inheriting texture of hot rolled sheets. On the other hand, compared to the (Cu,Mn)S particles, the Nb(C,N) particles significantly hinder the primary recrystallized grain growth. The onset of secondary recrystallization for Cu-bearing steel is 950 °C, while the growth of Nb-primary grains continue to be strongly inhibited at 975 °C. After high-temperature annealing, a high magnetic induction (B8 is ≈1. 8 T) is obtained in Cu-bearing steel. In contrast, in Nb-bearing steel, there is no secondary recrystallization or the non-Goss grain ({113} ) is abnormal growth, and the magnetic induction B8 is ≈1.48–1.5 T. The lower magnetic induction of Nb-bearing silicon steel is related to the lower fraction of primary Goss texture and the stronger pinning effect of Nb(C,N) inhibitors.