Search

In order to better reflect the actual ecological performance of vehicles in traffic conditions, both the emission standards and the applied emission tests are being developed, for example by considering exhaust emissions for a cold engine start. This article presents the research results on the impact of ambient temperature during the cold start of a gasoline engine in road emission tests. The Real Driving Emissions (RDE) tests apply to passenger cars that meet the Euro 6 emissions norm and they are complementary to their type approval tests. A portable emissions measurement system was used to record the engine and vehicle operating parameters, as well as to measure the exhaust emissions during tests. This allowed for parameters such as engine load, engine speed and vehicle speed to be monitored. The cold start conditions for two different temperatures (8°C and 25°C) were compared in detail. Moreover, the engine operating parameters, exhaust concentration values and road emissions for the 300 s time interval, were compared. The summary of the article presents the share of a passenger car’s cold start phase for each exhaust compound in the urban part of the test and in the entire Real Driving Emissions test depending on the ambient temperature.

The article compares the exhaust emissions in road conditions of city buses: LNG and Diesel. Both buses met the Euro VI exhaust emission norm. The current strong drive to diversify fuels in Poland and the creation of a large gas port in Świnoujście for LNG imports creates an excellent opportunity to use this fuel, also in road transport. Therefore, the attempt to identify the emission in operation, in first place possible applications, i.e. an LNG bus, comparatively with the emission of a Diesel bus. The operational research carried out concerned such a bus and has not yet been carried out in the country, hence their innovation, also methodological. The conducted research, in particular, was aimed at verifying differences in exhaust emissions of carbon dioxide and nitrogen oxides. The study was carried out on one urban bus route performing trips on consecutive days in similar environmental conditions. The performed tests were not strictly type approval tests but only used for comparative purposes. Hence, it was necessary to determine the compliance factor for the relevant exhaust gas substances, with the use of an evaluation algorithm based on measurement windows. Based on these results, the assumption regarding compliance with the emission requirements for the tested buses was verified in real traffic conditions. The exhaust emission values (emission indicators) determined in this way did not exceed the permissible emission limit values for carbon monoxide, while for nitrogen oxides and non-methane hydrocarbons certain exceedances were found.

The article addresses the usage patterns of plug-in hybrid vehicles (PHEVs) under Polish conditions. The conventional approach to operating such vehicles assumes that they are used with a fully charged battery at the start. However, the economic circumstances of Polish users often do not allow for daily charging of vehicles from the domestic power grid. As a result, these vehicles are used not only in a mode powered solely by the internal combustion engine but also in a mode where the internal combustion engine is primarily utilized to charge the battery. An analysis was conducted on various ways of operating plug-in vehicles, evaluating not only harmful emissions but also fuel consumption (for battery states of charge: SOC = 100%, SOC = 50%, SOC = 0%, and SOC = 0 → 100%—forced charging mode). The study focused on the most characteristic vehicle segment in Poland, SUVs, and employed a methodology for determining exhaust emissions under real-world driving conditions. Results indicate that forced charging of such a vehicle's battery leads to over a 25-fold increase in carbon dioxide emissions (fuel consumption) in urban areas compared to operating the vehicle with a fully charged battery (CO—25× increase, NOx—12× increase, PN—11× increase). Operating a plug-in SUV without charging it from the power grid results in a 13-fold increase in fuel consumption compared to using the vehicle with a fully charged battery (CO—10× increase, NOx—6× increase, PN—4× increase). The emission results were used to evaluate Poland's charging infrastructure in the context of PHEV usage. The current state of the infrastructure and its development plans for 2030 and 2040 were analyzed. It was found that significant reductions in fuel consumption (by approximately 30%) and CO2 emissions are achievable by 2040. Emissions of CO, NOx, and PN are expected to decrease by about 10%, primarily due to the internal combustion engine operating at high load conditions in non-urban or highway scenarios. [ABSTRACT FROM AUTHOR]

The increasing number of vehicles operating in Poland, especially passenger vehicles, justifies the need to conduct air pollution emission tests in the context of the impact of vehicles on the natural environment. Firstly, this article reviews the publications related to air pollutant emissions and passenger vehicles traveling on Polish roads. However, it presents a special method using advanced research equipment to determine air pollutant emissions. The above research methods are justified in implementing clean transport zones. Real Driving Emissions represent an essential procedure in the implementation of clean transport zones in Poland, verifying the actual emissions of air pollutants and modeling this phenomenon using the results of real air pollutant emissions. The results of this research state that establishing a link between a vehicle's air pollutant emissions and its age can support making transport or delivery planning more sustainable and choosing less carbon-intensive means of transport to reduce the negative impact of transport on the environment. The scientific novelty of the proposed solutions is the verification of the actual emissions of Euro 6 vehicles and the modeling of air pollutant emissions as a function of speed and acceleration. The research results are included in this article and will become input data for further analysis in examining the impact of vehicle operating age on air pollution emissions. Consequently, the novelty of the present research also lies in its focus on the verification of the impact of operating age, particularly in the context of vehicles exceeding 15 years of age, on air pollutant emissions. By establishing a correlation between a vehicle's air pollutant emissions and its operating age, it becomes possible to make transport or delivery planning more sustainable. Furthermore, the selection of less carbon-intensive means of transport can contribute to reducing the negative impact of transport on the environment. [ABSTRACT FROM AUTHOR]

The subject of assessing exhaust emissions in real driving conditions has been relevant for a long time. Its introduction into approval tests focused attention on the comparative possibilities of tests performed on a chassis dynamometer and in road conditions. The article is a continuation of research on the possibilities of estimating emissions in the Real Driving Emission test based on emission data from Worldwide harmonized Light Vehicles Test Cycles. The first part discussed the possibility of comparing dynamic parameters in these tests, and the second part discussed the possibility of estimating road exhaust emissions. The work was done in two stages: the first stage involved the use of distance-specific emissions in individual parts of the WLTC test, and the second stage involved the use of exhaust emission rates as datasets divided into intervals defined by vehicle speed and acceleration. Comparative tests were performed for conventional vehicles (gasoline, diesel) and hybrid vehicles. A chassis dynamometer was used to carry out WLTC tests and PEMS equipment was used for the RDE tests. The exhaust gas components that had to be measured in road tests, namely: carbon monoxide, carbon dioxide, nitrogen oxides, and the number of particulate matter, were analyzed. Based on the data collected, parameters such as road emissions and the exhaust emissions rate were determined for each phase of the dynamometer test as well as the road test. Because of this, it was possible to compare the distance-specific exhaust emissions of each vehicle in the two emission tests. The comparison resulted in establishing that it is possible to estimate distance-specific exhaust emissions of conventional and hybrid vehicles in road test conditions, using only the results obtained in the approval test (for selected test phases). The research concluded that it is possible to estimate selected RDE test parameters based on the results obtained in the WLTC test for the tested vehicles. [ABSTRACT FROM AUTHOR]

The article is an attempt to perform an ecological assessment of passenger cars with various types of engines in road emission tests. The main research problem and, at the same time, the goal was to develop a method for determining the exhaust emissions from motor vehicles in real traffic conditions based on results obtained in homologation tests. The tests were carried out on vehicles equipped with gasoline, diesel, and hybrid engines, and the obtained results were analyzed. All of the selected vehicles were of the same class—passenger cars, with a similar curb weight, similar maximum engine power, and in the same emission class (Euro 6d). The authors compared the dynamic parameters of vehicle motion in established emission tests: Worldwide harmonized Light vehicles Test Cycles and Real Driving Emissions. Four procedures were used to analyze and compare the operating conditions of the vehicles in the WLTC and RDE tests, differing in how the phases in the tests were divided as well as having a different methodology for determining the road emissions in the tests. The procedures were as follows: WLTC (where the test was divided and the determination of the road emission of exhaust gases was carried out according to the standard WLTP procedure), RDE (the road test was divided into sections and the exhaust emission was determined according to the standard RDE procedure), WLTC1+2 (the test was divided into phases: 1 + 2, 3, and 4; a combination of phases 1 and 2 corresponding to the urban section of the RDE test), WLTCRDE (where drive phases were divided and emissions determined in the same way as in the RDE procedure, which assumes the division of the test into sections based on vehicle speed). The implementation of the research task in the form of an algorithm procedure when comparing the dynamic parameters of the movement in the WLTC and RDE tests is the leading goal presented in this article. The division of the WLTC test into sections (urban, rural, and motorway) according to the RDE procedure and also the calculation of the total emissions in the test according to this procedure resulted in obtaining similar road emission values in the test. [ABSTRACT FROM AUTHOR]

Hybrid vehicles account for the largest share of new motor vehicle sales in Europe. These are vehicles that are expected to bridge the technological gap between vehicles with internal combustion engines and electric vehicles. Such a solution also makes it possible to meet the limits of motor vehicle emissions, at a time when it is particularly important to test them under actual traffic conditions. This article analyzes the impact of the length of the test routes in relation to current, but also future regulations of approval standards. Three routes of post-phase composition (urban, rural, motorway) with lengths of about 30, 16 and 8 km were selected for the study. Measurements of the main emission components were made using portable emission measurement systems (PEMS), and exhaust emissions were determined using the moving average window (MAW) method. Analysis of the obtained results led to the conclusion that the current requirements for the RDE test (in particular, the duration of the test) enforce a length of each part of 32 km. Reducing the test to 60–90 min causes the individual phases to last 16 km, and the main advantage of such a solution is the very strong influence of the cold start phase on the emission results in the urban phase. Future declarations by lawmakers to drastically reduce the length of the test phases to 8 km will force hybrid vehicles to be tested largely using the internal combustion engine. This will be the right thing to do, especially in the urban phase, as now in addition to a significant reduction in the engine warm-up phase, manufacturers will have to take into account that such an engine thermal condition can also occur in the rural phase. [ABSTRACT FROM AUTHOR]

The amount of hybrid vehicles and their contribution have increased in the global market. They are a promising aspect for a decrease in emissions. Different tests are used to determine the factors of such emissions. The goal of the present study was to compare the emissions of two hybrid vehicles of the same manufacturer: the plug-in version and the HEV version (gasoline + electric engine). These vehicles were chosen because they comprise the largest market share of hybrid cars in Poland. The exhaust emission tests were conducted in the WLTC tests on a chassis dynamometer and under real traffic conditions. Simultaneous testing on a dyno and under real driving is the most adequate test to assess the environmental aspects of vehicles—especially hybrids. The combustion engines of the tested vehicles were supplied with gasoline containing 5% biocomponents. The emissions, including CO2, CO, NOx, THC and PNs, were measured in accordance with the European Union procedure. According to the latter, the resistance to motion of the chassis dyno was adjusted to the road load, allowing the hybrid vehicles to move in electric mode and allowing the dynamometer to operate in energy recovery mode. The obtained emissions of CO2, CO, NOx and THC in the case of the plug-in hybrid vehicle were lower by 3%, 2%, 25%, and 13%, respectively, compared to the case of HEV. Fuel consumption in the case of the plug-in hybrid vehicle was lower by 3%, and PN was lower by 10% compared to the case of HEV (WLTC). In real driving conditions, the differences were more pronounced in favour of the plug-in vehicle: CO2 emissions in the RDE test were 30% lower, NOx emissions were 50% lower, and PN was 10% lower. An increase in emissions was only observed for CO2 emissions—the plug-in vehicle's on-road emissions were 6% higher compared to the HEV. The obtained emissions for FC and PN varied with actual velocity values due to competitive driving between a combustion engine and an electric motor, as well as existing acceleration and deceleration events during the test and other factors. [ABSTRACT FROM AUTHOR]

The paper describes the method of investigations of exhaust emissions from a combustion engine under operation classified in terms of its dynamic states. In this paper, the engine operating states are determined through the vehicle driving under actual traffic conditions in the RDE (Real Driving Emissions) test. Based on the recorded tracings of the vehicle velocity, the engine states were classified as static for the acceleration of the absolute value lower than the adopted classification limit. Besides, the authors analyzed the engine operating states for the positive as well as negative acceleration. For the adopted engine operating states, zero-dimensional characteristics of the emission intensity for individual exhaust components were determined (average value, coefficient of variation). The influence of the analyzed operating states on the emission of individual exhaust components was assessed. The greatest increase in the intensity of the emission of nitrogen oxides was observed for the positive vehicle acceleration model and the lowest (also for the nitrogen oxides) for the negative vehicle acceleration. On average, the greatest increase in the emission intensity of pollutants and the intensity of particle number occurred for the dynamic states of the engine corresponding to positive acceleration. The conclusions from the performed investigations entitle the authors to propose a greater allowance for the exhaust emission-related criteria in the engine control algorithms. [ABSTRACT FROM AUTHOR]

On-road driving tests are performed to determine the emission of harmful exhaust compounds from vehicles. These primarily include carbon dioxide, nitrogen oxides, and particle number. However, there is a lack of indicators that combine the first three substances that are the most important in assessing the environmental aspects of vehicles. The purpose of this article is to indicate the possibility of assessing emissions in real driving conditions from light-duty and heavy-duty vehicles of different categories. In order to do so, a portable emissions measurement system (PEMS) and an instrument for measuring the particle number were used. The tests were carried out on routes designed to comply with the requirements and regulations laid down in the European Union legislation. On-road emissions of carbon dioxide, nitrogen oxides and particle number have been determined. Factors have been determined as the multiplication of these compounds for each vehicle category in three phases of the test: urban, rural, and motorway. A new way of assessing emissions from vehicles using new factors has been proposed. [ABSTRACT FROM AUTHOR]

The paper describes the methodology of research of exhaust emissions from a combustion engine under engine states determined by the vehicle actual operation in the RDE test. The processes of quantities determining the vehicle motion and engine states have been recorded, along with the exhaust emission intensity. Based on the developed research methodology, zero-dimensional characteristics of the processes of the emission intensity have been determined under the conditions of urban, rural and motorway traffic, as well as in the entire test. The authors also determined the average specific distance exhaust emissions under the conditions of urban, rural and motorway traffic, as well as in the entire test. Based on the above results, the unique characteristics of the relation of the average specific distance emissions and the average vehicle speed have been obtained. The obtained characteristics may be used in the modeling of exhaust emissions from motor vehicles under actual traffic conditions. The authors also explored the sensitivity of the average specific distance emissions to the vehicle driving style. [ABSTRACT FROM AUTHOR]