Search

In this contribution, we investigate the B_\text1 distribution and coupling characteristics of a multichannel radio frequency (RF) coil consisting of different dipole coil elements for 7 T MRI, and explore the feasibility to achieve a compromise between field distribution and decoupling by combining different coil elements. Two types of dipole elements are considered here: the meander dipole element with a chip-capacitor-based connection to the RF shield which achieves a sufficient decoupling between the neighboring elements; and the open-ended meander dipole element which exhibits a broader magnetic field distribution. By nesting the open-ended dipole elements in between the ones with end-capacitors, the B_\text1 distribution, in terms of field penetration depth and homogeneity, is improved in comparison to the dipole coil consisting only of the elements with end-capacitors, and at the same time, the adjacent elements are less coupled to each other in comparison to the dipole coil consisting only of the open-ended elements. The proposed approach is validated by both full-wave simulation and experimental results. [ABSTRACT FROM AUTHOR]

In this paper, we present a fundamental investigation to improve the B1 efficiency and the signal-to-noise ratio (SNR) of a radio frequency (RF) surface coil for ultrahigh-field magnetic resonance imaging (MRI) by utilizing a high-impedance surface (HIS) as the RF shield. An analytical investigation indicates that a circular loop backed by a perfect magnetic conductor (PMC), which is the ideal case of an HIS, suggests an improved magnetic field compared with the case of a perfect electric conductor (PEC) and the case without any shield. This improvement is verified by a full-wave simulation, where the surface coil is modeled by an ideal impressed current model with azimuthal component ( J\text {surf, \alpha }= 1 A/m). The electromagnetic field is effectively shielded out behind the PEC and PMC shields compared with the case without any shield. Furthermore, the surface coil with uniform current distribution and the PMC shield is realized by a series resonant loop structure and a 2-D HIS structure, respectively. Since the normal component of the magnetic field is supported at the surface of an HIS, whereas suppressed by a conventional PEC, the \boldsymbolB1 field in the vicinity of the HIS shield is enhanced compared with the case with a PEC shield. Hence, an improvement on SNR and \boldsymbolB1 efficiency is achieved by utilizing an HIS shield, especially in the regions adjacent to the surface coil. It has been found that the improvement of B1 efficiency is more prominent than the improvement of SNR due to different normalizations. The difference of peak SAR between considered shields, which is used for B1 efficiency normalization, is considerably larger than the difference of the power loss within the phantom, which is used for the SNR normalization. The proposed approach is validated by full-wave finite-element method simulations and near-field measurements, which reveal good agreement with each other. [ABSTRACT FROM PUBLISHER]

In this paper, we systematically investigate the electromagnetic (EM) field of a stripline dipole coil element backed by various shielding plates, which are characterized by surface impedance. The initial analysis is based on a 2-D finite-element-method model, where the considered surface impedance was categorized in terms of magnitude and phase. It has been demonstrated that the shielding plate can be approximately modeled by the magnitude of a complex surface impedance if the absolute EM field distribution is considered. Additionally, as the magnitude of the surface impedance increases, the magnetic and electric fields excited by the stripline tend to distribute in a broader manner. Thus, the transversal homogeneity of the B1 field of a stripline coil can be improved by a shielding plate with a high surface impedance, which has been verified by 3-D models based on single- and multi-coil elements. For the experimental validation, two shielding plates—a copper-plated substrate and a high-impedance surface, which exhibits a small and large surface impedance, respectively—are considered. An excellent agreement of field distributions between numerical simulation and measurement has been observed. [ABSTRACT FROM PUBLISHER]

This contribution discusses the utilization of RF power in an MRI system with RF mode shimming which enables the superposition of circularly polarized modes of a transmit RF coil array driven by a Butler matrix. Since the required power for the individual modes can vary widely, mode-shimming can result in a significant underutilization of the total available RF power. A variable power combiner (VPC) is proposed to improve the power utilization: it can be realized as a reconfiguration of the MRI transmit system by the inclusion of one additional matrix network which receives the power from all transmit amplifiers at its input ports and provides any desired (combined) power distribution at its output ports by controlling the phase and amplitude of the amplifiers’ input signals. The power distribution at the output ports of the VPC is then fed into the “mode” ports of the coil array Butler matrix in order to superimpose the spatial modes at the highest achievable power utilization. The VPC configuration is compared to the standard configuration of the transmit chain of our MRI system with 8 transmit channels and 16 coils. In realistic scenarios, improved power utilization was achieved from 17% to 60% and from 14% to 55% for an elliptical phantom and a region of interest in the abdomen, respectively, and an increase of the power utilization of 1 dB for a region of interest in the upper leg. In general, it is found that the VPC allows significant improvement in power utilization when the shimming solution demands only a few modes to be energized, while the technique can yield loss in power utilization in cases with many modes required at high power level. [ABSTRACT FROM PUBLISHER]

This paper presents a realistic feasibility of radio frequency identification (RFID) based self-localization of objects in real environments using simple infrastructure composed of chipless tags. These tags are designed as arrays of dielectric resonators (DR) in order to overcome the range limitations of the traditional chipless tags, where the DR array structure of the tags boosts the radar cross section (RCS) and, consequentially, extends the range coverage. Furthermore, an efficient algorithm for tag detection is proposed considering the environmental and hardware impairments that alter the backscattered signal from the tag. In this system, the reader interrogates the reference nodes, i.e. chipless tags, by a frequency-sweep RF signal, and the backscattered signals from the tags are captured and analyzed at the reader for detection, ranging and location estimation. A testbed is implemented with fabricated chipless RFID tags in order to evaluate the validity and accuracy of the proposed self-localization system. Experimental measurements based simulations are conducted in several scenarios in order to evaluate the proposed system. Moreover, an object (the reader) is moved to several locations in an interrogation area of $2.5\times 1.2$ m, and, afterwards, its location is estimated. The averaged measured location error achieved based on the proposed system is approximately 5 cm with a variation of 0.9 cm as a minimum observed error and 7 cm as a maximum error. [ABSTRACT FROM AUTHOR]

Passive chipless tags based on dielectric resonators (DRs) have been proposed for a novel millimeter-wave indoor self-localization system to mark fixed reference nodes. The tags employed in the system provide a unique spectral signature (resonance peaks) with much-increased radar cross section (RCS) by placing several identical DRs at the focal line of a spherical dielectric lens. Resonators of optimized geometry allow a modification of this original DR-lens tag by combining the lens with different size DRs which exhibit resonant frequencies separated by large frequency gaps. For easier manufacturing and testing, a demonstrator tag was designed for a “scaled” frequency range of 5–6 GHz with this configuration and is shown to produce spectral signatures of the monostatic RCS which are uniquely related to the angle of arrival (AoA) of the incident wave from a reader. Simulated signatures of a lens of 120-mm diameter with seven spherical DRs are presented and results are supported by experiment. Correlation processing of the signatures can give a resolution of few degrees in AoA while the bistatic RCS half-power beamwidth is on the order of 20°, and RCS levels of resonant peaks are produced between 0 and −6 dBm2. [ABSTRACT FROM AUTHOR]

Indoor localization based on unsynchronized, low-complexity, passive radio frequency identification (RFID) using the received signal strength indicator (RSSI) has a wide potential for a variety of internet of things (IoTs) applications due to their energy-harvesting capabilities and low complexity. However, conventional RSSI-based algorithms present inaccurate ranging, especially in indoor environments, mainly because of the multipath randomness effect. In this work, we propose RSSI-based localization with low-complexity, passive RFID infrastructure utilizing the potential benefits of large-scale MIMO technology operated in the millimeter-wave band, which offers channel hardening, in order to alleviate the effect of small-scale fading. Particularly, by investigating an indoor environment equipped with extremely simple dielectric resonator (DR) tags, we propose an efficient localization algorithm that enables a smart object equipped with large-scale MIMO exploiting the RSSI measurements obtained from the reference DR tags in order to improve the localization accuracy. In this context, we also derive Cramer–Rao lower bound of the proposed technique. Numerical results evidence the effectiveness of the proposed algorithms considering various arbitrary network topologies, and results are compared with an existing algorithm, where the proposed algorithms not only produce higher localization accuracy but also achieve a greater robustness against inaccuracies in channel modeling. [ABSTRACT FROM AUTHOR]