Search

The characteristics of aortic valvular outflow jet affect aortopathy in the bicuspid aortic valve (BAV). This study aimed to elucidate the effects of BAV morphology on the aortic valvular outflow jets. Morphotype-specific valve-devising apparatuses were developed to create aortic valve models. A magnetic resonance imaging-compatible pulsatile flow circulation system was developed to quantify the outflow jet. The eccentricity and circulation values of the peak systolic jet were compared among tricuspid aortic valve (TAV), three asymmetric BAVs, and two symmetric BAVs. The results showed mean aortic flow and leakage did not differ among the five BAVs (six samples, each). Asymmetric BAVs demonstrated the eccentric outflow jets directed to the aortic wall facing the smaller leaflets. In the asymmetric BAV with the smaller leaflet facing the right-anterior, left-posterior, and left-anterior quadrants of the aorta, the outflow jets exclusively impinged on the outer curvature of the ascending aorta, proximal arch, and the supra-valvular aortic wall, respectively. Symmetric BAVs demonstrated mildly eccentric outflow jets that did not impinge on the aortic wall. The circulation values at peak systole increased in asymmetric BAVs. The bicuspid symmetry and the position of smaller leaflet were determinant factors of the characteristics of aortic valvular outflow jet.

Background: Underfilled transcatheter aortic-valve implantation with ad hoc post-dilation is a therapeutic option for patients with borderline annuli to avoid acute complication. The effects of this technique on valve leaflet behavior, hydrodynamic performances, and paravalvular leakage (PVL) using patient-specific three-dimensional (3D) aortic-valve models were investigated. Methods and Results: A female octogenarian patient was treated with this technique by using a 23-mm Sapien-XT. Patient-specific models were constructed from pre-procedure computed tomography (CT) data. Change in aortic annulus areas during systolic/diastolic phases and post-procedure stent areas were adjusted to those of the patient. The following was performed: (1) -3 cc initial and -2 cc underfilled post-dilation to the scale-down model by adjusting percent oversizing; and (2) -1 cc initial underfilling, nominal volume, and repeat nominal volume post-dilation using the patient-specific model. Underfilling was associated with higher %PVL. Observation using a high-speed camera revealed distorted leaflets after underfilled implantation, with a longer valve-closing time and smaller effective orifice areas, especially in the -3 cc underfilled implantation. Micro-CT analysis revealed that the transcatheter valves shifted to the opposite side of the large annulus calcification after post-dilation and reduced the malapposition there., Conclusions: Excessive underfilled implantation showed unacceptable acute hemodynamics. Abnormal leaflet motions after underfilled implantation raised concerns about durability. Flow simulations using patient-oriented 3D models could help to investigate hemodynamics, leaflet motions, and the PVL mechanism.

Background: Quantitative assessment of post-transcatheter aortic valve replacement (TAVR) aortic regurgitation (AR) remains challenging. We developed patient-specific anatomical models with pulsatile flow circuit and investigated factors associated with AR after TAVR., Methods: Based on pre-procedural computed tomography (CT) data of the six patients who underwent transfemoral TAVR using a 23-mm SAPIEN XT, anatomically and mechanically equivalent aortic valve models were developed. Forward flow and heart rate of each patient in two days after TAVR were duplicated under mean aortic pressure of 80mmHg. Paravalvular leakage (PVL) volume in basal and additional conditions was measured for each model using an electromagnetic flow sensor. Incompletely apposed tract between the transcatheter and aortic valves was examined using a micro-CT., Results: PVL volume in each patient-specific model was consistent with each patient's PVL grade, and was affected by hemodynamic conditions. PVL and total regurgitation volume increased with the mean aortic pressure, whereas closing volume did not change. In contrast, closing volume increased proportionately with heart rate, but PVL did not change. The minimal cross-sectional gap had a positive correlation with the PVL volumes (r=0.89, P=0.02). The gap areas typically occurred in the vicinity of the bulky calcified nodules under the native commissure., Conclusions: PVL volume, which could be affected by hemodynamic conditions, was significantly associated with the minimal cross-sectional gap area between the aortic annulus and the stent frame. These data may improve our understanding of the mechanism of the occurrence of post-TAVR PVL., (Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.)

The final goal of this study is to realize a low-cost pulsatile blood pump especially for patients with acute heart failure or postoperative low cardiac output syndrome. In support of the pump, two types of polymer bileaflet valves with different configuration of the valve seats were developed. Influence of the leaflet thickness on the hydrodynamics of the prototype was preliminarily investigated among 70 microm, 100 microm, and 150 microm. As to the valves with the thinner leaflets, buckling of the leaflets was observed, which induced a large amount of regurgitation at valve closure. However, by thickening the leaflet to 150 microm, the mean flow of the prototype and the second model could be successfully comparable to the Medtronic-Hall valve. Moreover, accelerated fatigue tests showed that reinforcement of the valve seat with the additional spokes in the second model extended the durability by four times as compared with the prototype, equivalent to an in vivo duration of over one month.

Mechanical circulatory support (MCS) devices, including veno-arterial extracorporeal membrane oxygenation (VA-ECMO) and Impella, have been widely used for patients with cardiogenic shock (CS). However, hemodynamics with each device and combination therapy is not thoroughly understood. We aimed to elucidate the hemodynamics with MCS using a pulsatile flow model. Hemodynamics with Impella CP, VA-ECMO, and a combination of Impella CP and VA-ECMO were assessed based on the pressure and flow under support with each device and the pressure–volume loop of the ventricle model. The Impella CP device with CS status resulted in an increase in aortic pressure and a decrease in end-diastolic volume and end-diastolic pressure (EDP). VA-ECMO support resulted in increased afterload, leading to a significant increase in aortic pressure with an increase in end-systolic volume and EDP and decreasing venous reservoir pressure. The combination of Impella CP and VA-ECMO led to left ventricular unloading, regardless of increase in afterload. Hemodynamic support with Impella and VA-ECMO should be a promising combination for patients with severe CS. [ABSTRACT FROM AUTHOR]

Open in new tab Download slide OBJECTIVES Transcatheter mitral valve repair is an emerging alternative to the surgical repair. This technology requires preclinical studies to assess efficacy in mitigating mitral regurgitation (MR). However, ex vivo MR models are not established. We developed 2 novel repairable models, functional and degenerative, which can quantitatively assess regurgitation and effect of intervention. METHODS We used porcine mitral valves and a pulsatile flow circulation system. In the functional MR model, the annulus was immersed in 0.1% collagenase solution and dilated using 3D-printed dilators. To control the regurgitation grade, the sizes of the dilator and silicone sheet in which the valve was sutured to were adjusted. Chordae of P2 were severed in the degenerative model, and the number of severed chordae was adjusted to control the regurgitation grade. Models were repaired using the edge-to-edge or artificial chordae technique. RESULTS The mean regurgitant fraction of the moderate–severe functional and degenerative models were 47.9% [standard deviation (SD): 2.2%] and 58.5% (SD: 8.0%), which were significantly reduced to 28.7% (SD: 4.4%) (P  < 0.001) and 26.0% (SD: 4.4%) (P  < 0.001) after the valve repair procedures. Severe functional model had a mean regurgitant fraction of 59.4% (SD: 6.0%). CONCLUSIONS Both functional and degenerative models could produce sufficient MR levels that meet the interventional indication criteria. The repairable models are valuable in evaluating the efficacy of valve repair procedures and devices. The ability to control the amount of regurgitation enhances the versatility and reliability of these models. These reproducible models could expedite the development of novel devices. [ABSTRACT FROM AUTHOR]

Purpose: To compare the characteristics of reimplantation (RI) using grafts with sinuses and remodeling (RM) with/without external suture annuloplasty using a pulsatile flow simulator. Methods: Porcine aortic roots were obtained from an abattoir, and six models of RM and RI with sinuses were prepared. External suture annuloplasty (ESA) was performed in the RM models to decrease the root diameter to 22 mm (RM-AP22) and 18 mm (RM-AP18). Valve models were tested at mean pulsatile flow and aortic pressure of 5.0 L/min and 120/80 (100) mmHg, respectively, at 70 beats/min. The forward flow, regurgitation, leakage, backflow rates, valve-closing time, and mean and peak pressure gradient (p-PG) were evaluated. Root configurations were examined using micro-computed tomography (micro-CT). Results: The backflow rate was larger in the RM models than in the RI models (RI: 8.56% ± 0.38% vs. RM: 12.64% ± 0.79%; p < 0.01). The RM-AP and RI models were comparable in terms of the forward flow, regurgitation, backflow rates, p-PG, and valve-closing time. The analysis using a micro-CT showed a larger dilatation of the sinus of the Valsalva in the RM groups than in the RI group (Valsalva: RI, 26.55 ± 0.40 mm vs. RM-AP22, 31.22 ± 0.55 mm [p < 0.05]; RM-AP18, 31.05 ± 0.85 mm [p < 0.05]). Conclusions: RM with ESA and RI with neo-sinuses showed comparable hemodynamics. ESA to RM reduced regurgitation. [ABSTRACT FROM AUTHOR]

Open in new tab Download slide Open in new tab Download slide OBJECTIVES Sinus plication has emerged as a promising tool that can lead to better stability in bicuspid aortic valve (BAV) repair. However, the mechanisms underlying the efficacy of this technique are unclear. We evaluated the hydrodynamic effect of sinus plication using the experimental pulsatile flow simulator and our original BAV model in vitro. METHODS Based on the computed tomography data of a BAV patient who had undergone aortic valvuloplasty, a BAV model (group C, n  =   6) was developed with bovine pericardium and vascular prosthesis (J-graft Shield Neo Valsalva 24 mm). We performed sinus plication (group SP, n  =   6) in the BAV model and compared hydrodynamic data with the control model in the pulsatile flow simulator. Non-fused cusp angle, annulus diameter and effective height were measured by ultrasonography. RESULTS The average flow was significantly increased in group SP compared to group C (4.24 ± 0.14 l/min vs 4.14 ± 0.15 l/min, respectively, P  =   0.034). The mean transvalvular pressure gradient and regurgitant fraction were significantly decreased in group SP compared to group C (11.6 ± 4.3 mmHg vs 16.6 ± 5.0 mmHg, respectively, P  =   0.009 and 14.1 ± 2.0% vs 17.4 ± 2.1%, respectively, P  =   0.001). Ultrasound measurement indicated that non-fused cusp angle was significantly increased in group SP compared to group C (163.8° ± 9.2° vs 153.0° ± 4.6°, respectively, P  =   0.012). CONCLUSIONS Sinus plication in the BAV model significantly increased the commissural angle. It was effective in not only controlling regurgitation but also improving valve opening. These finding should be confirmed by evaluating cusp stress and/or long-term durability in the future studies. [ABSTRACT FROM AUTHOR]